CISCO-MPLS-TE-STD-EXT-MIB

All MIBs › CISCO-MPLS-TE-STD-EXT-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2016-08-05

Category: Cisco Devices, MPLS and Traffic Engineering

Description: Adds Cisco-specific TE tunnel attributes and performance statistics to the IETF MPLS Traffic Engineering MIB.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-MPLS-TE-STD-EXT-MIB?

CISCO-MPLS-TE-STD-EXT-MIB is a Cisco extension to the IETF MPLS-TE-STD-MIB, adding Cisco-specific managed objects for MPLS Traffic Engineering (TE) tunnels on Cisco routing platforms. Its principal content is the auto-bandwidth feature, which lets an MPLS TE tunnel automatically resize its reserved bandwidth to match measured load, exposing configuration thresholds along with adjustment, overflow, and underflow parameters. From a monitoring standpoint it supports watching software-level tunnel behavior -- the current auto-bandwidth status, and how close a tunnel's actual load is to its overflow/underflow thresholds -- to catch tunnels that are chronically over- or under-provisioned. It explicitly extends the standards-based MPLS-TE-STD-MIB (IETF) and is meant to be used alongside it rather than standalone. It is deployed on Cisco MPLS-TE-capable routers in service-provider and large enterprise WAN/MPLS backbones that use dynamically adjusted TE tunnel bandwidth. Engineers can download the CISCO-MPLS-TE-STD-EXT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-MPLS-TE-STD-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco routers/label switch routers running MPLS Traffic Engineering (auto-bandwidth extension to MPLS-TE-STD-MIB)

Monitoring Examples

cmplsTunnelAutoBWTable/cmplsTunnelAutoBWEntry rows (keyed per TE tunnel) expose cmplsTunnelAutoBWStatus, cmplsTunnelAutoBWMin, and cmplsTunnelAutoBWMax so an operator can confirm auto-bandwidth is enabled and see its allowed range. Polling cmplsTunnelAutoBWAdjThreshPercs/BW alongside cmplsTunnelAutoBWOverflowThreshPercs/BW and cmplsTunnelAutoBWOverflowLimit reveals whether a tunnel is repeatedly hitting its overflow threshold -- a sign that its configured max bandwidth is too low for actual traffic. cmplsTunnelAutoBWUnderflowThreshPercs/BW would similarly flag a tunnel that is over-provisioned relative to its real load.

What Can Be Monitored

auto-bandwidth enable status per tunnel
min/max auto-bandwidth range
overflow/underflow threshold and limits
bandwidth adjustment thresholds

Imported Objects

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From MPLS-TE-STD-MIB

mplsTunnelARHopListIndex	OBJECT-TYPE
mplsTunnelAdminStatus	OBJECT-TYPE
mplsTunnelEgressLSRId	OBJECT-TYPE
mplsTunnelIndex	OBJECT-TYPE
mplsTunnelIngressLSRId	OBJECT-TYPE
mplsTunnelInstance	OBJECT-TYPE
mplsTunnelName	OBJECT-TYPE
mplsTunnelOperStatus	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using cmplsTunnelAutoBWApplications OID:

Select a Cisco MPLS-TE routers/label switch router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cmplsTunnelAutoBWApplications into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object indicates the number of auto bandwidths applied. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cmplsTeStdExtMIB	1.3.6.1.4.1.9.9.738			This MIB module contains Cisco specific managed object definitions for MPLS Traffic Engineering (TE), not contained in MPLS-TE-STD-MIB. The auto bandwidth feature enables MPLS TE Tunnels to adapt automatically their bandwidth to their actual load.
cmplsTeStdExtMIBNotifs	1.3.6.1.4.1.9.9.738.0
NTF cmplsTunnelPreempt	1.3.6.1.4.1.9.9.738.0.1			This notification is generated when a MPLS TE tunnel is preempted.
NTF cmplsTunnelInsuffBW	1.3.6.1.4.1.9.9.738.0.2			This notification is generated when a MPLS TE tunnel could not be setup or reoptimized.
NTF cmplsTunnelReRoutePending	1.3.6.1.4.1.9.9.738.0.3			This notification is generated when re-route is required for the tunnel.
NTF cmplsTunnelReRoutePendingClear	1.3.6.1.4.1.9.9.738.0.4			This notification is generated when tunnel no longer needs to be re-routed.
NTF cmplsTunnelBringupFail	1.3.6.1.4.1.9.9.738.0.5			This notification is generated when MPLS TE tunnel failed to come up
cmplsTeStdExtMIBObjects	1.3.6.1.4.1.9.9.738.1
cmplsTunnelAutoBWTable	1.3.6.1.4.1.9.9.738.1.1		not-accessible	This table is used in order to manage auto bandwidth data. This table is sparse dependent on the mplsTunnelTable. An entry in this table exists for each mplsTunnelEntry with a mplsTunnelRole of 'head' or 'headTail'. Each row contains auto-bandwidth data for the tunnel identified by the indexes defined later. An entry is created as soon as a 'head' or 'headTail' MPLS TE tunnel is configured in the system.
cmplsTunnelAutoBWEntry	1.3.6.1.4.1.9.9.738.1.1.1		not-accessible	A conceptual row in cmplsTunnelAutoBWTable. There is an entry in this table for each MPLS-TE tunnel with mplsTunnelRole equals to 'head' or 'headTail'.
INT cmplsTunnelAutoBWStatus	1.3.6.1.4.1.9.9.738.1.1.1.1	INTEGER	read-only	This object indicates the operational status [or mode] of the auto bandwidth algorithm: - autoBWDisabled: The auto-bandwidth algorithm is not running; - autoBWEnabled: The auto-bandwidth algorithm is running; - autoBWCollectOnlyMode: The auto-bandwidth algorithm is running, but the bandwidth applications are disabled;
U32 cmplsTunnelAutoBWMin	1.3.6.1.4.1.9.9.738.1.1.1.2	Unsigned32	read-write	This object specifies the minimum bandwidth that the auto-bandwidth algorithm can apply to a tunnel when the adjustment threshold is overcome. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWMax	1.3.6.1.4.1.9.9.738.1.1.1.3	Unsigned32	read-write	This object specifies the maximum bandwidth that the auto-bandwidth algorithm can apply to a tunnel when the adjustment threshold is overcome. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
CMP cmplsTunnelAutoBWAdjThreshPercs	1.3.6.1.4.1.9.9.738.1.1.1.4	CmplsTunnelBWPercent	read-write	This object specifies the adjustment threshold percentage that needs to be overcome in order to trigger a new bandwidth application. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWAdjThreshBW	1.3.6.1.4.1.9.9.738.1.1.1.5	Unsigned32	read-write	This object specifies the adjustment threshold bandwidth that needs to be overcome in order to trigger a new bandwidth application. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
CMP cmplsTunnelAutoBWOverflowThreshPercs	1.3.6.1.4.1.9.9.738.1.1.1.6	CmplsTunnelBWPercent	read-write	This object specifies the adjustment threshold percentage that needs to be overcome in order to trigger an overflow occurrence. If the application period has not completed when a cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWOverflowThreshBW	1.3.6.1.4.1.9.9.738.1.1.1.7	Unsigned32	read-write	This object specifies the adjustment threshold bandwidth that needs to be overcome in order to trigger an overflow occurrence. If the application period has not completed when a cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWOverflowLimit	1.3.6.1.4.1.9.9.738.1.1.1.8	Unsigned32	read-write	This object specifies the number of consecutive collections exceeding overflow threshold. If the application period has not completed when a cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
CMP cmplsTunnelAutoBWUnderflowThreshPercs	1.3.6.1.4.1.9.9.738.1.1.1.9	CmplsTunnelBWPercent	read-write	This object specifies the adjustment threshold percentage that needs to be overcome in order to trigger an underflow occurrence. If the application period has not completed when a cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWUnderflowThreshBW	1.3.6.1.4.1.9.9.738.1.1.1.10	Unsigned32	read-write	This object specifies the adjustment threshold bandwidth that needs to be overcome in order to trigger an underflow occurrence. If the application period has not completed when a cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWUnderflowLimit	1.3.6.1.4.1.9.9.738.1.1.1.11	Unsigned32	read-write	This object specifies the number of consecutive collections under the underflow threshold. If the application period has not completed when a cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new bandwidth will be applied. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWApplicationFrequency	1.3.6.1.4.1.9.9.738.1.1.1.12	Unsigned32	read-write	This object specifies the bandwidth application period. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWCollectionFrequency	1.3.6.1.4.1.9.9.738.1.1.1.13	Unsigned32	read-write	This object specifies the sampling period for data rates. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWLastAppliedBW	1.3.6.1.4.1.9.9.738.1.1.1.14	Unsigned32	read-only	This object indicates the last bandwidth applied by the auto-bandwidth algorithm. It will be set to zero if no bandwidth has been applied yet. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWApplicationsEx	1.3.6.1.4.1.9.9.738.1.1.1.15	Counter32	read-only	This object indicates the number of auto bandwidths applied. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
INT cmplsTunnelAutoBWLastApplicationTrigger	1.3.6.1.4.1.9.9.738.1.1.1.16	INTEGER	read-only	This object indicates the trigger reason for the last bandwidth application. If mplsTunnelInstance is zero this object will be set to 'applicationNone'. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWOverflowApplications	1.3.6.1.4.1.9.9.738.1.1.1.17	Counter32	read-only	This object indicates the number of bandwidth applications due to overflow occurrences. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWOverflowOccurrences	1.3.6.1.4.1.9.9.738.1.1.1.18	Counter32	read-only	This object indicates the number of overflow occurrences since last application period. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWUnderflowApplications	1.3.6.1.4.1.9.9.738.1.1.1.19	Counter32	read-only	This object indicates the number of bandwidth applications due to underflow occurrences. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWUnderflowOccurrences	1.3.6.1.4.1.9.9.738.1.1.1.20	Counter32	read-only	This object indicates the number of underflow occurrences since last application period. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
G32 cmplsTunnelAutoBWUnderflowHighestBW	1.3.6.1.4.1.9.9.738.1.1.1.21	Gauge32	read-only	This object indicates the highest sample collected during an underflow sequence. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWRequested	1.3.6.1.4.1.9.9.738.1.1.1.22	Unsigned32	read-only	This object indicates the bandwidth requested by the auto-bandwidth algorithm. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWSignaled	1.3.6.1.4.1.9.9.738.1.1.1.23	Unsigned32	read-only	This object indicates the bandwidth signaled by the auto-bandwidth algorithm. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWCollectOnlyRequested	1.3.6.1.4.1.9.9.738.1.1.1.24	Unsigned32	read-only	This object indicates the bandwidth that would have been requested by the auto-bandwidth algorithm if the auto-bandwidth functionality was enabled. If the collect only mode is enabled, the bandwidth change request will not be executed. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWHighest	1.3.6.1.4.1.9.9.738.1.1.1.25	Unsigned32	read-only	This object indicates the highest bandwidth sampled by the auto-bandwidth algorithm. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
C32 cmplsTunnelAutoBWCollectedSamples	1.3.6.1.4.1.9.9.738.1.1.1.26	Counter32	read-only	This object indicates the samples collected since the last auto-bandwidth application. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
U32 cmplsTunnelAutoBWJitter	1.3.6.1.4.1.9.9.738.1.1.1.27	Unsigned32	read-only	This object indicates the auto-bandwidth application jitter. Jitter is the extra time to be added to the application interval the first time the auto bandwidth is applied. If mplsTunnelInstance is zero this object will be set to zero. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
INT cmplsTunnelAutoBWAppRejectReason	1.3.6.1.4.1.9.9.738.1.1.1.28	INTEGER	read-only	This object indicates the reason for the bandwidth application rejection. This object value is not aplicable if cmplsTunnelAutoBWStatus is 'autoBWDisabled'.
cmplsTeTunnelReasonTable	1.3.6.1.4.1.9.9.738.1.2		not-accessible	This table is used in order to indicate the causes for the notifications.
cmplsTeTunnelReasonEntry	1.3.6.1.4.1.9.9.738.1.2.1		not-accessible	A conceptual row in cmplsTunnelReasonTable.
INT cmplsTunnelReoptReason	1.3.6.1.4.1.9.9.738.1.2.1.1	INTEGER	accessible-for-notify	This object indicates the reason of the tunnel reoptimization: - unknown: the reason is not known - periodicTimerExpiry: Periodic Reoptimization - bandwidthCLIChange: the tunnel bandwidth has been changed from CLI - bandwidthOverflow: an auto-bandwidth overflow occurred - bandwidthUnderflow: an auto-bandwidth underflow occured - bandwidthAdjustment: an auto-bandwidth application occured - fastReRoute: a fast re-route occured - cliRequest: User-triggerred - metricTypeChange: tunnel metric type has been changed from CLI - preferredPathExists: preferred-path-exists message received from a downstream node - poSwitchoverTrigger: User-requested path-option switchover - bandwidthChange: bandwidth change - autoBandwidth: Auto Bandwidth - remergeError: Remerge Error - dueToMaximumMetric: Reoptimization due to receiving an LSA with MAX metric - pathProtectionSwitchover: Path Protection Switchover - iEPEnableReoptimization: IEP Enable Reoptimization - affinityPathVerificationFail: Affinity path verification failure - softPreemption: soft preemption (see RFC 5712) - preferredTreeExists: preferred-tree-exists message received from a downstream node - costLimitPathVerificationFail: Cost Limit path verification failure - linkupReopt: link state up - iEPChangeReoptimization: inuse explicit-path change - poChangeReoptimization: inuse path-option change - bfdSessionTypeChange: a bfd session type change occured This object is intended to be included in the trap mplsTunnelReoptimized defined in MPLS-TE-STD-MIB.
INT cmplsTunnelInsuffBWFailedOperation	1.3.6.1.4.1.9.9.738.1.2.1.2	INTEGER	accessible-for-notify	This object indicates whether the tunnel could not be setup or reoptimized because of insufficient bandwidth: - unknown: the reason is not known - failedToSetup: insufficient bandwidth during initial setup - failedToReoptimize: insufficient bandwidth during reoptimization
INT cmplsTunnelPreemptionType	1.3.6.1.4.1.9.9.738.1.2.1.3	INTEGER	accessible-for-notify	This object indicates LSP Preemption type of this LSP: - unknown: the type is not known - hardPreemption: the preempted LSP resources are freed immediately; the LSP is broken immediately and the traffic is disrupted. - softPreemption: the resources release pending on the reoptimization of this LSP. The head of the LSP reroutes the traffic before the LSP is broken. - frrSoftPreemption: similar to softPreemption. In this case the traffic of the soft preempted LSP is switched to the backup. See: Farrel, A., Interim Report on MPLS Pre-emption, draft-farrel-mpls-preemption-interim-00.txt, work in progress
IPt cmplsTunnelPreemptionLinkAddrType	1.3.6.1.4.1.9.9.738.1.2.1.4	InetAddressType	accessible-for-notify	This object indicates the address type of the link where the preemption occurs - another, higher priority LSP is being admitted on this link and there is not enough bandwidth for it causing this LSP to be preempted (removed) from this link: - unknown: the object cmplsTunnelPreemptionLinkAddr does not contain any address - ipv4: the object cmplsTunnelPreemptionLinkAddr contains the IPv4 address - ipv6: the object cmplsTunnelPreemptionLinkAddr contains the IPv6 address
IP cmplsTunnelPreemptionLinkAddr	1.3.6.1.4.1.9.9.738.1.2.1.5	InetAddress	accessible-for-notify	This object indicates the address of the link where the preemption occurs - another, higher priority LSP is being admitted on this link and there is not enough bandwidth for it causing this LSP to be preempted (removed) from this link.
INT cmplsTunnelReRoutePendingClearReason	1.3.6.1.4.1.9.9.738.1.2.1.6	INTEGER	accessible-for-notify	This object indicates the reason why the tunnel is not longer in the reroute pending state: - unknown: the reason is unknown - reoptimized: the tunnel has been reoptimized - reinstated: the tunnel has been reinstated
cmplsTeTunnelFailReasonTable	1.3.6.1.4.1.9.9.738.1.3		not-accessible	This table is used in order to indicate the causes for the MPLS TE tunnel failure notifications.
cmplsTeTunnelFailReasonEntry	1.3.6.1.4.1.9.9.738.1.3.1		not-accessible	A conceptual row in the cmplsTeTunnelFailReasonTable.
INT cmplsTeFailReasonType	1.3.6.1.4.1.9.9.738.1.3.1.1	INTEGER	read-only	This object indicates the type (category) of fail reason.
I32 cmplsTeFailReason	1.3.6.1.4.1.9.9.738.1.3.1.2	Integer32	read-only	This object indicates specific fail reason value based on the fail reason type indicated by cmplsTeFailReasonType. Fail Reason Type Fail Reason Value Type ---------------- ----------------------- bfd(2) CiscoBfdDiag generalTe(3) CmplsTeTunnelDiag This object is replaced by cmplsTeFailReasonRev
INT cmplsTeFailReasonRev	1.3.6.1.4.1.9.9.738.1.3.1.3	INTEGER	accessible-for-notify	This object provieds more deails on fail reason. cmplsTeFailReason values for reasonType bfd(2) mirror the CiscoBfdDiag values: - noDiagnostic No bfd diagnostic info - controlDetectionTimeExpired Control Detection Timer Expired - echoFunctionFailed Echo Function Failed - neighborSignaledSessionDown Neighbor Signaled Session Down - forwardingPlaneReset Forwarding Plane Reset - pathDown Path Down - concatenatedPathDown Concatenated Path Down - administrativelyDown Administratively Down - reverseConcatenatedPathDown Reverse Concatenated Path Down - unknown Unknown error code cmplsTeFailReason values for reasonType generalTe(3) mirror the CmplsTeTunnelDiag values: - unknown Unknown error code - bfdSessionBringupTimeout bfd session failed to come up before timeout
cmplsTunnelLoadshareTable	1.3.6.1.4.1.9.9.738.1.4		not-accessible	This table is used in order to manage load data.
cmplsTunnelLoadshareEntry	1.3.6.1.4.1.9.9.738.1.4.1		not-accessible	A conceptual row in cmplsTunnelLoadshareTable. There is an entry in this table for each MPLS-TE tunnel.
U32 cmplsTunnelLoadShare	1.3.6.1.4.1.9.9.738.1.4.1.1	Unsigned32	read-write	This object indicates the Load-share as defined by the bandwidth attribute (default) or explicitly configured using the load-share command under tunnel configuration.
cmplsTeStdExtMIBObjectsGlobal	1.3.6.1.4.1.9.9.738.1.5
INT cmplsTeLoadshareBalance	1.3.6.1.4.1.9.9.738.1.5.1	INTEGER	read-write	This object indicates if the load-share balance is equal or unequal.
cmplsTeStdExtMIBConform	1.3.6.1.4.1.9.9.738.2
cmplsTeStdExtMIBCompliances	1.3.6.1.4.1.9.9.738.2.1
cmplsTeStdExtMIBCompliance	1.3.6.1.4.1.9.9.738.2.1.1			This is the main compliance statement for the MIB.
cmplsTeStdExtMIBCompliancesRev1	1.3.6.1.4.1.9.9.738.2.1.2			This is the main compliance statement for the MIB. Adding the extended traps.
cmplsTeStdExtMIBComplianceRev2	1.3.6.1.4.1.9.9.738.2.1.3			This is the main compliance statement for the MIB
cmplsTeStdExtMIBComplianceRev3	1.3.6.1.4.1.9.9.738.2.1.4			This is the main compliance statement for the MIB
cmplsTeStdExtMIBComplianceRev4	1.3.6.1.4.1.9.9.738.2.1.5			This is the main compliance statement for the MIB
cmplsTeStdExtMIBGroups	1.3.6.1.4.1.9.9.738.2.2
cmplsTeStdExtMIBAutoBWObjectGroup	1.3.6.1.4.1.9.9.738.2.2.1			This contains the main MPLS TE extensions groups.
cmplsTeStdExtMIBAutoBWOptionalGroup	1.3.6.1.4.1.9.9.738.2.2.2			This contains the optional MPLS TE extensions groups.
cmplsTeStdExtMIBTrapObjectsGroup	1.3.6.1.4.1.9.9.738.2.2.3			This contains the MPLS TE extended traps objects. This object is replaced by cmplsTeStdExtMIBTrapObjectsGroupRev1
cmplsTeStdExtMIBTrapObjectsGroupRev1	1.3.6.1.4.1.9.9.738.2.2.4			This contains the optional MPLS TE extensions groups.
cmplsTeStdExtMIBTrapGroup	1.3.6.1.4.1.9.9.738.2.2.5			This contains the MPLS TE extended traps.
cmplsTeStdExtMIBFailTeTrapGroup	1.3.6.1.4.1.9.9.738.2.2.6			This contains the MPLS TE extended traps related to BFD over TE LSP.
cmplsTeStdExtMIBFailTeTrapObjectsGroup	1.3.6.1.4.1.9.9.738.2.2.7			This contains the MPLS TE extended traps objects related to BFD over TE LSP. This object is replaced by cmplsTeStdExtMIBFailTeTrapObjectsGroupRev1
cmplsTeStdExtMIBLoadShareObjectsGroup	1.3.6.1.4.1.9.9.738.2.2.8			This contains the MPLS TE extended objects related to TE loadshare.
cmplsTeStdExtMIBFailTeTrapObjectsGroupRev1	1.3.6.1.4.1.9.9.738.2.2.9			This contains the MPLS TE extended traps objects related to BFD over TE LSP.

RFC description

Extends IETF MPLS Traffic Engineering MIB with Cisco-specific TE tunnel attributes and performance statistics.

Start monitoring Cisco MPLS-TE routers/label switch routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-MPLS-TE-STD-EXT-MIB