All MIBs › CISCO-LWAPP-WLAN-SECURITY-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2020-06-09
Category: Cisco Devices, VPN and Security, Wireless and WLAN
Description: Manages WLAN security settings including 802.1X, WPA, and encryption on Cisco LWAPP wireless controllers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-LWAPP-WLAN-SECURITY-MIB?
CISCO-LWAPP-WLAN-SECURITY-MIB is a Cisco enterprise MIB implemented on wireless LAN controllers that terminate the Lightweight Access Point Protocol (LWAPP) tunnel from Cisco lightweight access points, focused specifically on WLAN security configuration such as CCKM, WPA/WPA2, PSK, and fast-transition (FT) settings per wireless ESS (Extended Service Set). It exposes per-ESS security configuration objects covering encryption type, key management mode, pre-shared key format, and CCKM/WPA support flags. Administrators use it to monitor and verify the software-level security configuration state of each wireless network, confirming that the intended encryption (WPA1/WPA2) and key management mode are actively applied, and to receive notifications of security-related events via ciscoLwappWlanSecurityMIBNotifs. It depends on the broader Cisco LWAPP MIB family (controller/AP topology) since security settings are indexed per WLAN ESS defined elsewhere in that architecture. It is deployed on Cisco wireless LAN controllers managing fleets of lightweight access points in enterprise and campus WiFi deployments. Network engineers evaluating or troubleshooting this functionality can download the CISCO-LWAPP-WLAN-SECURITY-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-WLAN-SECURITY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco wireless LAN controller (LWAPP-based)
Monitoring Examples
An admin would poll cLWSecDot11EssCckmTable/cLWSecDot11EssCckmEntry to check cLWSecDot11EssCckmWpa2Security and cLWSecDot11EssCckmWpa2EncType per ESS, confirming that WPA2 with the expected encryption cipher is enforced rather than a weaker or misconfigured setting. cLWSecDot11EssPskFmt and cLWSecDot11EssPsk let an admin verify the pre-shared key format configured for a given WLAN, while cLWSecDot11EssFtEnable indicates whether 802.11r fast transition is enabled, useful when troubleshooting roaming or authentication delays reported by wireless clients.
What Can Be Monitored
- per-WLAN WPA/WPA2 encryption type
- CCKM support status
- pre-shared key configuration
- key management mode
- fast-transition (802.11r) status
This MIB depends on
Related MIBs
Imported Objects
From CISCO-LWAPP-TC-MIB
| CLSecEncryptType | |
| CLSecKeyFormat |
From CISCO-LWAPP-WLAN-MIB
| cLWlanIndex | OBJECT-TYPE |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoLwappWlanSecurityMIB | 1.3.6.1.4.1.9.9.521 | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is for WLAN security related features as specified in the CCKM, CKIP specifications. The relationship between the controller and the LWAPP APs is depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Advanced Encryption Standard ( AES ) In cryptography, the Advanced Encryption Standard (AES), also known as Rijndael, is a block cipher adopted as an encryption standard by the US government. It is expected to be used worldwide and analysed extensively, as was the case with its predecessor, the Data Encryption Standard (DES). AES was adopted by National Institute of Standards and Technology (NIST) as US FIPS PUB 197 in November 2001 after a 5-year standardisation process. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Cisco Centralized Key Management ( CCKM ) Client and AP exchange several EAPOL packets in the process of EAP authenticaton to determine dynamic session key (NSK), which is used for encrypting packets between them. When client moves to new-AP, it has to mutually authenticate with the new-AP and derive new NSK. This is being done by using complete EAP authentication (which is time consuming and causes noticeable delay in the voice application). Till that time, no data packets are being transmitted between new-AP and client. CCKM implementation in first controller caches client's credentials like session, vlanid, ssid, etc. and propagates the same to other controllers in mobility group. Currently a set of controller can be configured as part of a mobility group. If client roams across access points associated to this set of controllers, then with CCKM implementation in place, the L2 authentication will not happen. To make this happen a CCKM cache is maintained on each controller and the first controller where client gets associated update rest of the controllers in mobility group. On later reassociations, controller validates the CCKM specific IE present and allow associations. Wireless LAN Access Points (APs) manufactured by Cisco Systems have features and capabilities beyond those in related standards (e.g., IEEE 802.11 suite of standards, Wi-Fi recommendations by WECA, 802.1X security suite, etc). A number of features provide higher performance. For example, Cisco AP transmits a specific Information Element, which the clients adapt to for enhanced performance. Similarly, a number of features are implemented by means of proprietary Information Elements, which Cisco clients use in specific ways to carry out tasks above and beyond the standard. Other examples of feature categories are roaming and power saving. Cisco Key Integrity Protocol ( CKIP ) A proprietary implementation similar to TKIP. CKIP implements key permutation for protecting the CKIP key against attacks. Other features of CKIP include expansion of encryption key to 16 bytes of length for key protection and MIC to ensure data integrity. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Multilinear Modular Hash ( MMH ) This is a message authentication code. The original message is run through the hash (with a secret key), and the code is the result. The code is sent along with the original message. The receiver of the message calculates the hash over the original message (also with the secret key) and compares the final message authentication code with the code sent with the message. If the two codes match, the receiver can be assured that the original message is authentic. Pre-Shared Key ( PSK ) Pre-shared keys are normally used for interoperability purposes. The basic idea is that two parties sharing a common secret can communicate securely. This idea has been used since cryptography first sprung onto the scene. Temporal Key Integrity Protocol ( TKIP ) A security protocol defined to enhance the limitations of WEP. Message Integrity Check and per-packet keying on all WEP-encrypted frames are two significant enhancements provided by TKIP to WEP. Wired Equivalent Privacy ( WEP ) A security method defined by 802.11. WEP uses a symmetric key stream cipher called RC4 to encrypt the data packets. Wi-Fi Protected Access ( WPA ) Wi-Fi Protected Access (WPA and WPA2) are security systems created in response to several serious weaknesses found in Wired Equivalent Privacy (WEP). WPA implements the majority of the IEEE 802.11i standard, and was intended as an intermediate measure to take the place of WEP while 802.11i was prepared. WPA is designed to work with all wireless network interface cards, but not necessarily with first generation wireless access points. Protected Management Frame (PFM) Wi-Fi certified WPA2 with Protected Management Frames provides a WPA2-level of protection for unicast and multicast management action frames. Unicast management actions frames are protected from both eavesdropping and forging, and multicast management action frames are protected from forging. WPA2 with Protected Management Frames augments WPA2 privacy protections already in place for data frames with mechanisms to improve the resiliency of mission-critical networks. Authentication, Authorization, and Accounting (AAA) Authentication, authorization, and accounting (AAA) is a term for a framework for intelligently controlling access to computer resources, enforcing policies, auditing usage, and providing the information necessary to bill for services. Remote Authentication Dial In User Service (RADIUS) Remote Authentication Dial-In User Service (RADIUS) is a networking protocol that provides centralized Authentication, Authorization, and Accounting (AAA or Triple A) management for users who connect and use a network service. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications, Amendment 6, MAC Security Enhancements. [2] draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol | ||
| ciscoLwappWlanSecurityMIBNotifs | 1.3.6.1.4.1.9.9.521.0 | |||
| ciscoLwappWlanSecurityMIBObjects | 1.3.6.1.4.1.9.9.521.1 | |||
| clwsCckmConfig | 1.3.6.1.4.1.9.9.521.1.1 | |||
| cLWSecDot11EssCckmTable | 1.3.6.1.4.1.9.9.521.1.1.1 | not-accessible | This table represents the CCKM configuration for the WLANs configured on this controller. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable. The controller adds or deletes a row to this table whenever a WLAN is added or deleted. | |
| cLWSecDot11EssCckmEntry | 1.3.6.1.4.1.9.9.521.1.1.1.1 | not-accessible | Each entry represents a conceptual row in cLWSecDot11EssCckmTable and uniquely identified by cLWlanIndex. | |
| T/F cLWSecDot11EssCckmWpaSupport | 1.3.6.1.4.1.9.9.521.1.1.1.1.1 | TruthValue | read-write | This object specifies to enable or disable layer-2 security using WPA1 or WPA2. When this object is set to 'true' layer-2 security is enabled. When this object is set to 'false' layer-2 security is disabled. When layer-2 security is enabled, the following objects are only applied to environment and can be set. cLWSecDot11EssCckmWpa1Security cLWSecDot11EssCckmWpa1EncType cLWSecDot11EssCckmWpa2Security cLWSecDot11EssCckmWpa2EncType cLWSecDot11EssCckmKeyMgmtMode cLWSecDot11EssCckmGtkRandomize cLWSecDot11EssWpa3Security. |
| T/F cLWSecDot11EssCckmWpa1Security | 1.3.6.1.4.1.9.9.521.1.1.1.1.2 | TruthValue | read-write | This object specifies whether cckmwpa1 security is enabled or not. A value of 'true' indicates that WPA1 security is enabled on the controller. A value of 'false' indicates that WPA1 security is disabled on the controller. |
| CLS cLWSecDot11EssCckmWpa1EncType | 1.3.6.1.4.1.9.9.521.1.1.1.1.3 | CLSecEncryptType | read-write | This object specifies the type of WPA1 encryption configured on this WLAN. The value populated by this object is applicable only when cLWSecDot11EssCckmWpa1Security populates a value of 'true'. |
| T/F cLWSecDot11EssCckmWpa2Security | 1.3.6.1.4.1.9.9.521.1.1.1.1.4 | TruthValue | read-write | This object specifies whether cckmwpa2 security is enabled or not. A value of 'true' indicates that WPA2 security is enabled on the controller. A value of 'false' indicates that WPA2 security is disabled on the controller. |
| CLS cLWSecDot11EssCckmWpa2EncType | 1.3.6.1.4.1.9.9.521.1.1.1.1.5 | CLSecEncryptType | read-write | This object specifies the type of WPA2 encryption configured on this WLAN. The value populated by this object is applicable only when cLWSecDot11EssCckmWpa2Security populates a value of 'true'. |
| BIT cLWSecDot11EssCckmKeyMgmtMode | 1.3.6.1.4.1.9.9.521.1.1.1.1.6 | Bits | read-write | This object specifies the type of authentication key management that is applicable only when cLWSecDot11EssCckmWpaSupport is set to a value of 'true'. The following are the possible key management configurations allowed and accepted by the system. dot1x + CCKM dot1x only CCKM only PSK only FT fast transition dot1x only FT PSK only FT PSK + PSK FT dot1x + dot1x FT dot1x + dot1x + CCKM dot1x + CCKM +11w dot1x + 11w CCKM + 11w PSK + 11wPsk |
| CLS cLWSecDot11EssPskFmt | 1.3.6.1.4.1.9.9.521.1.1.1.1.7 | CLSecKeyFormat | read-write | This object specifies the type of the authentication preshared key configured through the object cLWSecDot11EssCckmPsk. Note that the key configuration is applicable only when psk is configured as the key management mechanism through the cLWSecDot11EssCckmKeyMgmtMode object. |
| OCT cLWSecDot11EssPsk | 1.3.6.1.4.1.9.9.521.1.1.1.1.8 | OCTET STRING | read-write | This object specifies the authentication pre-shared key in the hex format that is applicable only when the 'psk' bit is specified in the cLWSecDot11EssCckmKeyMgmtMode object. The length of the key that can be specified for the cLWSecDot11EssPsk object depends on the value of the cLWSecDot11EssPskFmt object as follows. 'ascii' 8-63 octets 'hex' 32 octets. |
| T/F cLWSecDot11EssCckmGtkRandomize | 1.3.6.1.4.1.9.9.521.1.1.1.1.9 | TruthValue | read-write | This object represents the Group Temporal Key(GTK) used for multicast and broadcast packet encryption in wpa1 and wpa2 clients. This object indicates the Group Temporal Key (GTK) configured on this WLAN that is applicable only when cLWSecDot11EssCckmWpaSupport is set to a value of 'true'. A value of 'true' indicates that Group Temporal Key (GTK) Randomization is enabled for a WLAN. A value of 'false' indicates that Group Temporal Key (GTK) Randomization is disabled for a WLAN. |
| T/F cLWSecDot11EssFtEnable | 1.3.6.1.4.1.9.9.521.1.1.1.1.10 | TruthValue | read-write | This object specifies whether fast transition is enabled for particular WLAN. A value of 'true' means that fast transition is enabled and A value of 'false' means that fast transition is disabled. |
| U32 cLWSecDot11EssFtReassocTime | 1.3.6.1.4.1.9.9.521.1.1.1.1.11 | Unsigned32 | read-write | This object specifies the fast transition re-association time. |
| T/F cLWSecDot11EssFtOverDs | 1.3.6.1.4.1.9.9.521.1.1.1.1.12 | TruthValue | read-write | This object specifies whether fast transition over distributed system is enabled. A 'true' value means that fast transition over the distributed system is enabled. A 'false' value means fast transition over the distributed system is disabled. |
| INT cLWSecDot11Ess11wPfm | 1.3.6.1.4.1.9.9.521.1.1.1.1.13 | INTEGER | read-write | This object specifies the 802.11w PFM status for a particular WLAN. |
| U32 cLWSecDot11EssRetryTime | 1.3.6.1.4.1.9.9.521.1.1.1.1.14 | Unsigned32 | read-write | This object specifies the 802.11w Security Association(SA) query retry timeout. |
| U32 cLWSecDot11EssComebackTime | 1.3.6.1.4.1.9.9.521.1.1.1.1.15 | Unsigned32 | read-write | This object specifies the 802.11w association comeback time. |
| INT cLWSecDot11EssFtMode | 1.3.6.1.4.1.9.9.521.1.1.1.1.16 | INTEGER | read-write | This object indicates the 11r status for a wlan cLWSecDot11EssFtMode is set to a value of 'adaptive'. |
| T/F cLWSecDot11EssWpa3Security | 1.3.6.1.4.1.9.9.521.1.1.1.1.17 | TruthValue | read-write | This object specifies whether wpa3 security is enabled or not. A value of 'true' indicates that WPA3 security is enabled on the controller. A value of 'false' indicates that WPA3 security is disabled on the controller. |
| T/F cLWSecDot11EssMPskEnable | 1.3.6.1.4.1.9.9.521.1.1.1.1.18 | TruthValue | read-write | This object specifies whether Multi-PSK security feature is enabled or not. True: indicates Multi-PSK security feature is enabled. False: indicates Multi-PSK security feature is disabled. |
| U32 cLWSecDot11EssSaeAntiClogThreshold | 1.3.6.1.4.1.9.9.521.1.1.1.1.19 | Unsigned32 | read-write | This object specifies the threshold for number of SAE open sessions beyond which Anti Clogging shall be enforced for future associations. |
| U32 cLWSecDot11EssSaeRetransTimeout | 1.3.6.1.4.1.9.9.521.1.1.1.1.20 | Unsigned32 | read-write | This object specifies the SAE Retransmission Timeout value. |
| I32 cLWSecDot11EssSaeMaxRetry | 1.3.6.1.4.1.9.9.521.1.1.1.1.21 | Integer32 | read-write | This object specifies the SAE maximum number of retry count |
| T/F cLWSecDot11OsenEnable | 1.3.6.1.4.1.9.9.521.1.1.1.1.22 | TruthValue | read-write | This object specifies whether Hotspot 2.0 OSEN security feature is enabled or not. True: indicates OSEN security feature is enabled. False: indicates OSEN security feature is disabled. |
| U32 cLWSecDot11TMWlanId | 1.3.6.1.4.1.9.9.521.1.1.1.1.23 | Unsigned32 | read-write | This object shall be used to configure OWE Transition mode support on the corresponding WLANs. Range: 0-4096. It enables OWE Transition mode on the corresponding WLANs. If it is 0, the transition mode is not enabled. |
| CLS cLWSecDot11EssWpa3EncType | 1.3.6.1.4.1.9.9.521.1.1.1.1.24 | CLSecEncryptType | read-write | This object specifies the type of WPA3 encryption configured on this WLAN. The value populated by this object is applicable only when cLWSecDot11EssWpa3Security populates a value of 'true'. |
| cLWSecDot11EssCkipTable | 1.3.6.1.4.1.9.9.521.1.1.2 | not-accessible | This table represents the CKIP parameters of a WLAN. This is a new layer-2 security policy similar to static WEP. User can select this policy on a WLAN. This policy will be allowed to be configured only when Aironet Extensions are enabled on the WLAN. Once user has selected CKIP he will be given an option to : 1> configure key 2> select MMH There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable. The controller adds or deletes a row to this table whenever a WLAN is added or deleted. | |
| cLWSecDot11EssCkipEntry | 1.3.6.1.4.1.9.9.521.1.1.2.1 | not-accessible | Each entry represents a conceptual row in cLWSecDot11EssCkipTable and uniquely identified by cLWlanIndex. | |
| T/F cLWSecDot11EssCkipSecurity | 1.3.6.1.4.1.9.9.521.1.1.2.1.1 | TruthValue | read-write | This object is used to enable to disable layer-2 CKIP as security policy for this WLAN. When this object is set to 'true', layer-2 CKIP security is enabled. When this object is set to 'false', layer-2 CKIP security is disabled. |
| U32 cLWSecDot11EssCkipKeyIndex | 1.3.6.1.4.1.9.9.521.1.1.2.1.2 | Unsigned32 | read-write | This object specifies the key index corresponding to the key being configured. A value of 0 indicates that the CKIP key hasn't been configured. |
| INT cLWSecDot11EssCkipKeyLength | 1.3.6.1.4.1.9.9.521.1.1.2.1.3 | INTEGER | read-write | This object specifies the length of CKIP key in bits that is applicable only when cLWSecDot11EssCkipSecurity is set as 'true'. |
| CLS cLWSecDot11EssCkipKeyFmt | 1.3.6.1.4.1.9.9.521.1.1.2.1.4 | CLSecKeyFormat | read-write | This object specifies the type of the key configured through the object cLWSecDot11EssCkipKey. |
| OCT cLWSecDot11EssCkipKey | 1.3.6.1.4.1.9.9.521.1.1.2.1.5 | OCTET STRING | read-write | This object specifies the CKIP key that is applicable only when cLWSecDot11EssCkipSecurity is set as 'true'. The number of characters to be configured depends on the key length and the key type configured through the objects cLWSecDot11EssCkipKeyLength and cLWSecDot11EssCkipKeyFmt respectively. The combinations are as follows. Key Type Number of characters hex 10/26 hex characters for 40/104 bits ascii 5/13 ascii characters for 40/104 bits. When cLWSecDot11EssCkipKeyFmt is set to 'hex', cLWSecDot11EssCkipKey can only be set to hexadecimal characters. To ensure consistency the following objects must be set together. cLWSecDot11EssCkipKeyFmt cLWSecDot11EssCkipKeyIndex cLWSecDot11EssCkipKeyLength cLWSecDot11EssCkipKey. |
| T/F cLWSecDot11EssCkipMMHMode | 1.3.6.1.4.1.9.9.521.1.1.2.1.6 | TruthValue | read-write | This object is used to enable or disable MMH MIC mode for the CKIP for this WLAN. 'true' - MMH MIC mode is enabled 'false' - MMH MIC mode is disabled. |
| T/F cLWSecDot11EssCkipKPEnable | 1.3.6.1.4.1.9.9.521.1.1.2.1.7 | TruthValue | read-write | This object specifies whether CKIP is enabled. A value of 'true' indicates that the encryption keys will be generated by permuting the static CKIP key configured through cLWSecDot11EssCkipKey. A value of 'false' indicates that CKIP is disabled. |
| cLWSecMPskKeysTable | 1.3.6.1.4.1.9.9.521.1.1.5 | not-accessible | This table represents the Multi-PSK configuration for the WLANs configured on the controller. Each row in this table corresponds to a Multi-PSK priority and pre-shared key combination. | |
| cLWSecMPskKeysEntry | 1.3.6.1.4.1.9.9.521.1.1.5.1 | not-accessible | Each entry represents a conceptual row in cLWSecMPskKeysTable table and is uniquely identified by cLWlanIndex and cLWSecMPskPriority | |
| U32 cLWSecMPskPriority | 1.3.6.1.4.1.9.9.521.1.1.5.1.1 | Unsigned32 | not-accessible | This object specifies the priority for Multi-PSK value |
| ROW cLWSecMPskRowStatus | 1.3.6.1.4.1.9.9.521.1.1.5.1.2 | RowStatus | read-create | The status of this conceptual row: To create a row in cLWSecMPskKeysTable table, set this object to either createAndGo(4) or createAndWait(5) and set cLWSecMPskPriority, cLWSecMPskKey and cLWSecMPskKeyFormat objects in the row to appropriate values. |
| CLS cLWSecMPskKeyFormat | 1.3.6.1.4.1.9.9.521.1.1.5.1.3 | CLSecKeyFormat | read-create | This object specifies the type of the authentication pre-shared key configured through the object cLWSecMPskKey. This configuration is applicable only when cLWSecDot11EssMPskEnable is enabled. |
| OCT cLWSecMPskKey | 1.3.6.1.4.1.9.9.521.1.1.5.1.4 | OCTET STRING | read-create | This object specifies the authentication pre-shared key that is applicable only when cLWSecDot11EssMPskEnable is enabled. The length of this attribute depends on the value of the cLWSecMPskKeyFormat: 'ascii': 8-63 octets 'hex' : 32 octets. |
| clwsCkipConfig | 1.3.6.1.4.1.9.9.521.1.2 | |||
| clwsWebPolicyConfig | 1.3.6.1.4.1.9.9.521.1.3 | |||
| cLWSecDot11EssWebPolicyTable | 1.3.6.1.4.1.9.9.521.1.3.1 | not-accessible | This table represents the conditional web-redirect parameters for the WLANs configured on this controller. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable. The controller adds or deletes a row to this table whenever a WLAN is added or deleted. | |
| cLWSecDot11EssWebPolicyEntry | 1.3.6.1.4.1.9.9.521.1.3.1.1 | not-accessible | Each entry represents a conceptual row in cLWSecDot11EssWebPolicyTable and uniquely identified by cLWlanIndex. | |
| T/F cLWSecDot11EssWebPolicyCondRedirect | 1.3.6.1.4.1.9.9.521.1.3.1.1.1 | TruthValue | read-write | This object is used to enable or disable conditional redirect. When this attribute is 'true', it signifies that conditional redirect is enabled and redirection of the client is done based on the url-redirect attribute provided by radius server. When this attribute is 'false', it signifies that conditional redirect is disabled and redirection of the client is not done, even if the url-redirect attribute is provided by the radius server. This attribute can be enabled only when 802.1x has been configured as layer-2 security the wlan and web policy is enabled on the wlan. |
| T/F cLWSecDot11EssWebPolicySplashPageWebRedirect | 1.3.6.1.4.1.9.9.521.1.3.1.1.2 | TruthValue | read-write | This object is used to enable or disable splash page web redirect. When this attribute is 'true', it signifies that splash page redirect is enabled and redirection of the client is done based on the url-redirect attribute provided by radius server. The redirect function works only for HTTP traffic. HTTPS redirect is not supported for any of the Web Policies. When this attribute is 'false', it signifies that splash page redirect is disabled and redirection of the client is not done. This attribute can be enabled only when 802.1x or WPA1+WPA2 has been configured as layer-2 security on the wlan. |
| clwsAaaConfig | 1.3.6.1.4.1.9.9.521.1.4 | |||
| INT cLWSecAaaRadiusAuthCallStationIdType | 1.3.6.1.4.1.9.9.521.1.4.1 | INTEGER | read-write | This object specifies the call station ID information sent in RADIUS authentication messages. ipAddr(1)- Sets Call Station Id Type to the system's IP Address. macAddr(2)- Sets Call Station Id Type to the system's MAC Address. apMacAddress(3)- Sets Call Station Id Type to the AP's Radio MAC Address. apMacAddressSsid(4)- Sets Call Station Id Type to the format :. apNameSsid(5)- Sets Called Station Id to the format :. apName(6)- Sets Called Station Id to the AP Name. apGroupName(7)- Sets Called Station Id to the AP Group Name. apLocation(8)- Sets Called Station Id to the AP Location. apVlanId(9)- Sets Called Station Id to the VLAN id. apMacEthAddress(10)- Sets Called Station Id Type to the AP's Ethernet MAC address. apMacEthAddressSsid(11)- Sets Called Station Id Type to the format :. apLabelAddress(12)- Sets Call Station Id Type to the AP MAC address printed on APLabel. apLabelAddressSsid(13)- Sets Call Station Id Type to the format :. |
| INT cLWSecAaaRadiusAccUsernameDelimiter | 1.3.6.1.4.1.9.9.521.1.4.2 | INTEGER | read-write | This object specifies the delimiter to be used when displaying the username for accounting request. For example, if the value of the username for accounting request is 1234567890ab. noDelimiter - display it as 1234567890ab. hyphen - display it as 12-34-56-78-90-ab colon - display it as 12:34:56:78:90:ab singleHyphen - display it as 123456-7890ab |
| clwsMpskConfig | 1.3.6.1.4.1.9.9.521.1.5 | |||
| ciscoLwappWlanSecurityMIBConform | 1.3.6.1.4.1.9.9.521.2 | |||
| ciscoLwappWlanSecurityMIBCompliances | 1.3.6.1.4.1.9.9.521.2.1 | |||
| ciscoLwappWlanSecurityMIBCompliance | 1.3.6.1.4.1.9.9.521.2.1.1 | The compliance statement for the SNMP entities that implement the ciscoLwappWlanSecurityMIB module. | ||
| ciscoLwappWlanSecurityMIBComplianceRev1 | 1.3.6.1.4.1.9.9.521.2.1.2 | The compliance statement for the SNMP entities that implement the ciscoLwappWlanSecurityMIB module. | ||
| ciscoLwappWlanSecurityMIBComplianceRev2 | 1.3.6.1.4.1.9.9.521.2.1.3 | The compliance statement for the SNMP entities that implement the ciscoLwappWlanSecurityMIB module. | ||
| ciscoLwappWlanSecurityMIBComplianceRev3 | 1.3.6.1.4.1.9.9.521.2.1.4 | The compliance statement for the SNMP entities that implement the ciscoLwappWlanSecurityMIB module. | ||
| ciscoLwappWlanSecurityMIBGroups | 1.3.6.1.4.1.9.9.521.2.2 | |||
| ciscoLwappWlanSecurityCckmConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.1 | This collection of objects represents CCKM related security parameters on a WLAN. The collection also configures the pre-shared keys when PSK is configured as the key management type. | ||
| ciscoLwappWlanSecurityCkipConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.2 | This collection of objects represents CKIP related security parameters on a WLAN. | ||
| ciscoLwappWlanSecurityWebPolicyConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.3 | This collection of objects represents conditional redirect parameters on a WLAN. | ||
| ciscoLwappWlanSecurityAaaConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.4 | This collection of objects represents AAA related security parameters on a WLAN. | ||
| ciscoLwappWlanSecurityFtConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.5 | This collection of objects represents fast transition related security parameters on a WLAN. | ||
| ciscoLwappWlanSecurityPfmConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.6 | This collection of objects represents PFM related security parameters on a WLAN. | ||
| ciscoLwappWlanSecurityCckmConfigGroup1 | 1.3.6.1.4.1.9.9.521.2.2.7 | This collection of objects represents GTK randomization information. | ||
| ciscoLwappWlanSecurityCckmConfigGroup2 | 1.3.6.1.4.1.9.9.521.2.2.8 | This collection of objects represents Multi-PSK information. | ||
| ciscoLwappWlanSecurityWPA3ConfigGroup | 1.3.6.1.4.1.9.9.521.2.2.9 | This collection of objects represents WPA3 related security parameters on a WLAN. |
RFC description
Cisco LWAPP MIB for wireless LAN security configuration and monitoring; manages authentication, encryption, and policy objects for Cisco wireless networks.
Start monitoring Cisco Wireless LAN Controllers (LWAPP-based) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.