CISCO-DOT3-OAM-MIB

All MIBs › CISCO-DOT3-OAM-MIB

Organization: Cisco Systems, Inc

Last Updated: 2006-05-31

Category: Cisco Devices, Network Interfaces

Description: Manages IEEE 802.3ah Ethernet OAM on Cisco devices, monitoring OAM discovery, link events, and remote loopback operations.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DOT3-OAM-MIB?

CISCO-DOT3-OAM-MIB implements management of IEEE 802.3ah Ethernet OAM (Operations, Administration, and Maintenance) features on Cisco switches and routers, covering Ethernet-in-the-First-Mile link monitoring. It exposes configuration data (admin state, OAM mode, max PDU size), operational status (operational state, functions supported), and peer discovery information (peer MAC address, vendor OUI), along with fault notifications for link events. It is explicitly useful for monitoring the software/link-layer health of a device: cdot3OamOperStatus reveals whether OAM discovery has completed and the link is being actively monitored, and the notification objects surface remote loopback and link fault events as they occur. This MIB is an extension of the IEEE 802.3ah/802.3-2005 standard, so it depends conceptually on that standard's OAM PDU model even though it is a Cisco-specific implementation. It is typically deployed on Cisco Ethernet access/aggregation devices at metro or first-mile network boundaries where OAM is used to detect and diagnose link faults remotely. Network engineers evaluating or troubleshooting this functionality can download the CISCO-DOT3-OAM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DOT3-OAM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco switches
Cisco routers

Monitoring Examples

An administrator would poll cdot3OamTable/cdot3OamEntry to check cdot3OamAdminState and cdot3OamOperStatus per interface, confirming OAM discovery succeeded, and inspect cdot3OamPeerTable/cdot3OamPeerEntry for cdot3OamPeerMacAddress and cdot3OamPeerVendorOui to verify the correct remote device was discovered. Receiving a trap from cdot3OamNotifications alongside an operational status change would indicate a link fault or loss of OAM peering that needs investigation.

What Can Be Monitored

OAM admin/operational state per interface
OAM discovery mode and max PDU size
peer MAC address and vendor OUI
link fault/loopback notifications
functions supported by remote OAM peer

Imported Objects

From CISCO-SMI

ciscoExperiment

OBJECT-IDENTITY

From HCNUM-TC

CounterBasedGauge64

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using cdot3OamInformationTx OID:

Select a Cisco switches and router (802.3ah Ethernet OAM) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cdot3OamInformationTx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports a count of the number of Information OAMPDUs transmitted on this interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in frames), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT cdot3OamAdminState	1.3.6.1.4.1.9.10.136.1.1.1.1	INTEGER	read-write	This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The cdot3OamAdminState always starts in the disabled(1) state until an explicit management action or configuration information retained by the system causes a transition to the enabled(2) state. When enabled(2), Ethernet OAM will attempt to operate over this interface.
cdot3OamCompliance	1.3.6.1.4.1.9.10.136.2.2.1			The compliance statement for managed entities supporting OAM on Ethernet like interfaces.
cdot3OamCompliances	1.3.6.1.4.1.9.10.136.2.2
U32 cdot3OamConfigRevision	1.3.6.1.4.1.9.10.136.1.1.1.5	Unsigned32	read-only	The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occurred which might require the peer OAM entity to re-evaluate whether OAM peering is allowed.
cdot3OamConformance	1.3.6.1.4.1.9.10.136.2
cdot3OamControlGroup	1.3.6.1.4.1.9.10.136.2.1.1			A collection of objects providing the abilities, configuration, and status of an Ethernet OAM entity.
T/F cdot3OamCriticalEventEnable	1.3.6.1.4.1.9.10.136.1.5.1.16	TruthValue	read-write	If true, the local OAM entity should attempt to indicate a critical event via the OAMPDU flags to its peer OAM entity when a critical event occurs. The exact definition of a critical event is implementation dependent. If the system does not support critical event capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
C32 cdot3OamDuplicateEventNotificationRx	1.3.6.1.4.1.9.10.136.1.4.1.6	Counter32	read-only	A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamDuplicateEventNotificationTx	1.3.6.1.4.1.9.10.136.1.4.1.5	Counter32	read-only	A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
T/F cdot3OamDyingGaspEnable	1.3.6.1.4.1.9.10.136.1.5.1.15	TruthValue	read-write	If true, the local OAM entity should attempt to indicate a dying gasp via the OAMPDU flags field to its peer OAM entity when a dying gasp event occurs. The exact definition of a dying gasp event is implementation dependent. If the system does not support dying gasp capability, setting this object has no effect, and reading the object should always result in 'false'. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
cdot3OamEntry	1.3.6.1.4.1.9.10.136.1.1.1		not-accessible	An entry in the table, containing information on the Ethernet OAM function for a single Ethernet like interface. Entries in the table are created automatically for each interface supporting Ethernet OAM. The status of the row entry can be determined from cdot3OamOperStatus. A cdot3OamEntry is indexed in the cdot3OamTable by the ifIndex object of the Interfaces MIB.
cdot3OamErrFrameEventGroup	1.3.6.1.4.1.9.10.136.2.1.7			A collection of objects for configuring the thresholds for an Errored Frame Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
T/F cdot3OamErrFrameEvNotifEnable	1.3.6.1.4.1.9.10.136.1.5.1.11	TruthValue	read-write	If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
cdot3OamErrFramePeriodEventGroup	1.3.6.1.4.1.9.10.136.2.1.6			A collection of objects for configuring the thresholds for an Errored Frame Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
T/F cdot3OamErrFramePeriodEvNotifEnable	1.3.6.1.4.1.9.10.136.1.5.1.8	TruthValue	read-write	If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
U32 cdot3OamErrFramePeriodThreshold	1.3.6.1.4.1.9.10.136.1.5.1.7	Unsigned32	read-write	The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If cdot3OamErrFramePeriodThreshold frame errors occur within a window of cdot3OamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.
U32 cdot3OamErrFramePeriodWindow	1.3.6.1.4.1.9.10.136.1.5.1.6	Unsigned32	read-write	The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If cdot3OamErrFramePeriodThreshold frame errors occur within a window of cdot3OamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.
T/F cdot3OamErrFrameSecsEvNotifEnable	1.3.6.1.4.1.9.10.136.1.5.1.14	TruthValue	read-write	If true, the local OAM entity should send an Event Notification OAMPDU when an Errored Frame Seconds Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
cdot3OamErrFrameSecsSummaryEventGroup	1.3.6.1.4.1.9.10.136.2.1.8			A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
I32 cdot3OamErrFrameSecsSummaryThreshold	1.3.6.1.4.1.9.10.136.1.5.1.13	Integer32	read-write	The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If cdot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of cdot3OamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
I32 cdot3OamErrFrameSecsSummaryWindow	1.3.6.1.4.1.9.10.136.1.5.1.12	Integer32	read-write	The amount of time (in 100ms intervals) over which the threshold is defined. The default value is 100 (10 seconds). If cdot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of cdot3OamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
U32 cdot3OamErrFrameThreshold	1.3.6.1.4.1.9.10.136.1.5.1.10	Unsigned32	read-write	The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm. If cdot3OamErrFrameThreshold frame errors occur within a window of cdot3OamErrFrameWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
U32 cdot3OamErrFrameWindow	1.3.6.1.4.1.9.10.136.1.5.1.9	Unsigned32	read-write	The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If cdot3OamErrFrameThreshold frame errors occur within a window of cdot3OamErrFrameWindow seconds (measured in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
cdot3OamErrSymbolPeriodEventGroup	1.3.6.1.4.1.9.10.136.2.1.5			A collection of objects for configuring the thresholds for an Errored Symbol Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.
T/F cdot3OamErrSymPeriodEvNotifEnable	1.3.6.1.4.1.9.10.136.1.5.1.5	TruthValue	read-write	If true, the OAM entity should send an Event Notification OAMPDU when an Errored Symbol Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cdot3OamFunctionsSupported attribute), this value is ignored.
U32 cdot3OamErrSymPeriodThresholdHi	1.3.6.1.4.1.9.10.136.1.5.1.3	Unsigned32	read-write	The two objects cdot3OamErrSymPeriodThresholdHi and cdot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as cdot3OamErrSymPeriodThreshold = ((2^32) * cdot3OamErrSymPeriodThresholdHi) + cdot3OamErrSymPeriodThresholdLo If cdot3OamErrSymPeriodThreshold symbol errors occur within a window of cdot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for cdot3OamErrSymPeriodThreshold is one symbol errors. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm.
U32 cdot3OamErrSymPeriodThresholdLo	1.3.6.1.4.1.9.10.136.1.5.1.4	Unsigned32	read-write	The two objects cdot3OamErrSymPeriodThresholdHi and cdot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as cdot3OamErrSymPeriodThreshold = ((2^32) * cdot3OamErrSymPeriodThresholdHi) + cdot3OamErrSymPeriodThresholdLo If cdot3OamErrSymPeriodThreshold symbol errors occur within a window of cdot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for cdot3OamErrSymPeriodThreshold is one symbol error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an asynchronous notification to the peer OAM entity of the statistics related to this threshold crossing alarm.
U32 cdot3OamErrSymPeriodWindowHi	1.3.6.1.4.1.9.10.136.1.5.1.1	Unsigned32	read-write	The two objects cdot3OamErrSymPeriodWindowHi and cdot3OamErrSymPeriodLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as cdot3OamErrSymPeriodWindow = ((2^32)*cdot3OamErrSymPeriodWindowHi) + cdot3OamErrSymPeriodWindowLo If cdot3OamErrSymPeriodThreshold symbol errors occur within a window of cdot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for cdot3OamErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.
U32 cdot3OamErrSymPeriodWindowLo	1.3.6.1.4.1.9.10.136.1.5.1.2	Unsigned32	read-write	The two objects cdot3OamErrSymPeriodWindowHi and cdot3OamErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as cdot3OamErrSymPeriodWindow = ((2^32)*cdot3OamErrSymPeriodWindowHi) + cdot3OamErrSymPeriodWindowLo If cdot3OamErrSymPeriodThreshold symbol errors occur within a window of cdot3OamErrSymPeriodWindow symbols, an Event Notification OAMPDU should be generated with an Errored Symbol Period Event TLV indicating the threshold has been crossed in this window. The default value for cdot3OamErrSymPeriodWindow is the number of symbols in one second for the underlying physical layer.
cdot3OamEventConfigEntry	1.3.6.1.4.1.9.10.136.1.5.1		not-accessible	Entries are automatically created and deleted from this table, and exist whenever the OAM entity supports Ethernet OAM events (as indicated by the eventSupport bit in cdot3OamFunctionsSuppported). Values in the table are maintained across changes to the value of cdot3OamOperStatus. Event configuration controls when the local management entity sends Event Notification OAMPDUs to its OAM peer, and when certain event flags are set or cleared in OAMPDUs.
cdot3OamEventConfigTable	1.3.6.1.4.1.9.10.136.1.5		not-accessible	Ethernet OAM includes the ability to generate and receive Event Notification OAMPDUs to indicate various link problems. This table contains the mechanisms to enable Event Notifications and configure the thresholds to generate the standard Ethernet OAM events. There is one entry in the table for every entry in cdot3OamTable that supports OAM events (where cdot3OamFunctionsSupported includes the eventSupport bit set). The values in the table are maintained across changes to cdot3OamOperStatus. The standard threshold crossing events are: - Errored Symbol Period Event. Generated when the number of symbol errors exceeds a threshold within a given window defined by a number of symbols (for example, 1,000 symbols out of 1,000,000 had errors). - Errored Frame Period Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a number of frames (for example, 10 frames out of 1000 had errors). - Errored Frame Event. Generated when the number of frame errors exceeds a threshold within a given window defined by a period of time (for example, 10 frames in 1 second had errors). - Errored Frame Seconds Summary Event. Generated when the number of errored frame seconds exceeds a threshold within a given time period (for example, 10 errored frame seconds within the last 100 seconds). An errored frame second is defined as a 1 second interval which had >0 frame errors. There are other events (dying gasp, critical events) that are not threshold crossing events but which can be enabled/disabled via this table.
cdot3OamEventLogEntry	1.3.6.1.4.1.9.10.136.1.6.1		not-accessible	An entry in the cdot3OamEventLogTable. Entries are automatically created whenever Ethernet OAM events occur at the local OAM entity, and when Event Notification OAMPDUs are received at the local OAM entity (indicating events have occurred at the peer OAM entity). The size of the table is implementation dependent, but when the table becomes full, older events are automatically deleted to make room for newer events. The table index cdot3OamEventLogIndex increments for each new entry, and when the maximum value is reached the value restarts at zero.
U32 cdot3OamEventLogEventTotal	1.3.6.1.4.1.9.10.136.1.6.1.12	Unsigned32	read-only	Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (cdot3OamLogRunningTotal) and the number of resultant Event Notifications (cdot3OamLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times one or more of these occurrences have resulted in an Event Notification (for example, 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).
cdot3OamEventLogGroup	1.3.6.1.4.1.9.10.136.2.1.10			A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event and maintaining the event information.
U32 cdot3OamEventLogIndex	1.3.6.1.4.1.9.10.136.1.6.1.1	Unsigned32	not-accessible	An arbitrary integer for identifying individual events within the event log.
INT cdot3OamEventLogLocation	1.3.6.1.4.1.9.10.136.1.6.1.5	INTEGER	read-only	Whether this event occurred locally (local(1)), or was received from the OAM peer via Ethernet OAM (remote(2)).
CDO cdot3OamEventLogOui	1.3.6.1.4.1.9.10.136.1.6.1.3	Cdot3Oui	read-only	The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs include their OUI in the Event Notification TLV which gets reflected here.
NUM cdot3OamEventLogRunningTotal	1.3.6.1.4.1.9.10.136.1.6.1.11	CounterBasedGauge64	read-only	Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (cdot3OamLogRunningTotal) and the number of resultant Event Notifications (cdot3OamLogEventTotal) should be identical. For threshold crossing events, since multiple occurrences may be required to cross the threshold, these values are likely different. This value represents the total number of times this event has happened since the last reset (for example, 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset).
cdot3OamEventLogTable	1.3.6.1.4.1.9.10.136.1.6		not-accessible	This table records a history of the events that have occurred at the Ethernet OAM level. These events can include locally detected events, which may result in locally generated OAMPDUs, and remotely detected events, which are detected by the OAM peer entity and signaled to the local entity via Ethernet OAM. Ethernet OAM events can be signaled by Event Notification OAMPDUs or by the flags field in any OAMPDU. This table contains both threshold crossing events and non-threshold crossing events. The parameters for the threshold window, threshold value, and actual value (cdot3OamEventLogWindowXX, cdot3OamEventLogThresholdXX, cdot3OamEventLogValue) are only applicable to threshold crossing events, and are returned as all F's (2^32 - 1) for non-threshold crossing events. Entries in the table are automatically created when such events are detected. The size of the table is implementation dependent. When the table reaches its maximum size, older entries are automatically deleted to make room for newer entries.
U32 cdot3OamEventLogThresholdHi	1.3.6.1.4.1.9.10.136.1.6.1.8	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects cdot3OamEventThresholdHi and cdot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cdot3OamEventLogThreshold = ((2^32) * cdot3OamEventLogThresholdHi) + cdot3OamEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 -1) and adds no useful information.
U32 cdot3OamEventLogThresholdLo	1.3.6.1.4.1.9.10.136.1.6.1.9	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects cdot3OamEventThresholdHi and cdot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cdot3OamEventLogThreshold = ((2^32) * cdot3OamEventLogThresholdHi) + cdot3OamEventLogThresholdLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.
TIM cdot3OamEventLogTimestamp	1.3.6.1.4.1.9.10.136.1.6.1.2	TimeStamp	read-only	The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notification OAMPDU indicating the event occurred on the peer. A system may attempt to adjust the timestamp value to more accurately reflect the time of the event at the peer OAM entity by using other information, such as that found in the timestamp found of the Event Notification TLVs, which provides an indication of the relative time between events at the peer entity.
U32 cdot3OamEventLogType	1.3.6.1.4.1.9.10.136.1.6.1.4	Unsigned32	read-only	The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFramePeriodEvent (2), erroredFrameEvent(3), erroredFrameSecondsEvent(4), linkFault(256), dyingGaspEvent(257), criticalLinkEvent(258) The first four are considered threshold crossing events as they are generated when a metric exceeds a given value within a specified window. The other three are not threshold crossing events. When the OUI is not 71874 (0x0180C2 in hex), then some other organization has defined the event space. If event subtyping is known to the implementation, it may be reflected here. Otherwise, this value should return all Fs (2^32 - 1).
NUM cdot3OamEventLogValue	1.3.6.1.4.1.9.10.136.1.6.1.10	CounterBasedGauge64	read-only	If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (for example, 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this value is returned as all F's (2^64 - 1) and adds no useful information.
U32 cdot3OamEventLogWindowHi	1.3.6.1.4.1.9.10.136.1.6.1.6	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects cdot3OamEventWindowHi and cdot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cdot3OamEventLogWindow = ((2^32) * cdot3OamEventLogWindowHi) + cdot3OamEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.
U32 cdot3OamEventLogWindowLo	1.3.6.1.4.1.9.10.136.1.6.1.7	Unsigned32	read-only	If the event represents a threshold crossing event, the two objects cdot3OamEventWindowHi and cdot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cdot3OamEventLogWindow = ((2^32) * cdot3OamEventLogWindowHi) + cdot3OamEventLogWindowLo Otherwise, this value is returned as all F's (2^32 - 1) and adds no useful information.
cdot3OamFlagEventGroup	1.3.6.1.4.1.9.10.136.2.1.9			A collection of objects for configuring the sending OAMPDUs with the critical event flag or dying gasp flag enabled.
C32 cdot3OamFramesLostDueToOam	1.3.6.1.4.1.9.10.136.1.4.1.17	Counter32	read-only	A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whenever a frame is dropped by the OAM layer. Note that any Ethernet frame, not just OAMPDUs, may be dropped by the OAM layer. This can occur when an OAMPDU takes precedence over a 'normal' frame resulting in the 'normal' frame being dropped. When this counter is incremented, no other counters in this MIB are incremented. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
BIT cdot3OamFunctionsSupported	1.3.6.1.4.1.9.10.136.1.1.1.6	Bits	read-only	The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs. Setting 'unidirectionalSupport(0)' indicates that the OAM entity supports the transmission of OAMPDUs on links that are operating in unidirectional mode (traffic flowing in one direction only). Setting 'loopbackSupport(1)' indicates the OAM entity can initiate and respond to loopback commands. Setting 'eventSupport(2)' indicates the OAM entity can send and receive Event Notification OAMPDUs. Setting 'variableSupport(3)' indicates the OAM entity can send and receive Variable Request and Response OAMPDUs.
cdot3OamGroups	1.3.6.1.4.1.9.10.136.2.1
C32 cdot3OamInformationRx	1.3.6.1.4.1.9.10.136.1.4.1.2	Counter32	read-only	A count of the number of Information OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamInformationTxEx	1.3.6.1.4.1.9.10.136.1.4.1.1	Counter32	read-only	A count of the number of Information OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamLoopbackControlRx	1.3.6.1.4.1.9.10.136.1.4.1.8	Counter32	read-only	A count of the number of Loopback Control OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamLoopbackControlTx	1.3.6.1.4.1.9.10.136.1.4.1.7	Counter32	read-only	A count of the number of Loopback Control OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
cdot3OamLoopbackEntry	1.3.6.1.4.1.9.10.136.1.3.1		not-accessible	An entry in the table, containing information on the loopback status for a single Ethernet like interface. Entries in the table are automatically created whenever the local OAM entity supports loopback capabilities. The loopback status on the interface can be determined from the cdot3OamLoopbackStatus object.
cdot3OamLoopbackGroup	1.3.6.1.4.1.9.10.136.2.1.4			A collection of objects for controlling the OAM remote loopback function.
INT cdot3OamLoopbackIgnoreRx	1.3.6.1.4.1.9.10.136.1.3.1.2	INTEGER	read-write	Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), OAM loopback commands are processed. The default value is to ignore loopback commands (ignore(1)).
INT cdot3OamLoopbackStatus	1.3.6.1.4.1.9.10.136.1.3.1.1	INTEGER	read-write	The loopback status of the OAM entity. This status is determined by a combination of the local parser and multiplexer states, the remote parser and multiplexer states, as well as by the actions of the local OAM client. When operating in normal mode with no loopback in progress, the status reads noLoopback(1). The values initiatingLooopback(2) and terminatingLoopback(4) can be read or written. The other values can only be read - they can never be written. Writing initiatingLoopback causes the local OAM entity to start the loopback process with its peer. This value can only be written when the status is noLoopback(1). Writing the value initiatingLoopback(2) in any other state has no effect. When in remoteLoopback(3), writing terminatingLoopback(4) causes the local OAM entity to initiate the termination of the loopback state. Writing terminatingLoopack(4) in any other state has no effect. If the OAM client initiates a looopback and has sent an Loopback OAMPDU and is waiting for a response, where the local parser and multiplexer states are DISCARD (see [802.3ah, 57.2.11.1]), the status is 'initiatingLoopback'. In this case, the local OAM entity has yet to receive any acknowledgement that the remote OAM entity has received its loopback command request. If the local OAM client knows that the remote OAM entity is in loopback mode (via the remote state information as described in [802.3ah, 57.2.11.1, 30.3.6.1.15]), the status is remoteLoopback(3). If the local OAM client is in the process of terminating the remote loopback [802.3ah, 57.2.11.3, 30.3.6.1.14], with its local multiplexer and parser states in DISCARD, the status is terminatingLoopback(4). If the remote OAM client has put the local OAM entity in loopback mode as indicated by its local parser state, the status is localLoopback(5). The unknown(6) status indicates the parser and multiplexer combination is unexpected. This status may be returned if the OAM loopback is in a transition state but should not persist. The values of this attribute correspond to the following values of the local and remote parser and multiplexer states. value LclPrsr LclMux RmtPrsr RmtMux noLoopback FWD FWD FWD FWD initLoopback DISCARD DISCARD FWD FWD rmtLoopback DISCARD FWD LPBK DISCARD tmtngLoopback DISCARD DISCARD LPBK DISCARD lclLoopback LPBK DISCARD DISCARD FWD unknown * any other combination *
cdot3OamLoopbackTable	1.3.6.1.4.1.9.10.136.1.3		not-accessible	This table contains controls for the loopback state of the local link as well as indicating the status of the loopback function. There is one entry in this table for each entry in cdot3OamTable that supports loopback functionality (where cdot3OamFunctionsSupported includes the loopbackSupport bit set). Loopback can be used to place the remote OAM entity in a state where every received frame (except OAMPDUs) is echoed back over the same interface on which they were received. In this state, at the remote entity, 'normal' traffic is disabled as only the looped back frames are transmitted on the interface. Loopback is thus an intrusive operation that prohibits normal data flow and should be used accordingly.
U32 cdot3OamMaxOamPduSize	1.3.6.1.4.1.9.10.136.1.1.1.4	Unsigned32	read-only	The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation.
cdot3OamMIB	1.3.6.1.4.1.9.10.136			The MIB module for managing the new Ethernet OAM features introduced by the Ethernet in the First Mile task force (IEEE 802.3ah). The functionality presented here is based on IEEE 802.3ah [802.3ah], released in October, 2004. [802.3ah] was prepared as an addendum to the standing version of IEEE 802.3 [802.3-2002] at the time. Since then, [802.3ah] has been merged into the base IEEE 802.3 specification in [802.3-2005]. In particular, this MIB focuses on the new OAM functions introduced in Clause 57 of [802.3ah]. The OAM functionality of Clause 57 is controlled by new management attributes introduced in Clause 30 of [802.3ah]. The OAM functions are not specific to any particular Ethernet physical layer, and can be generically applied to any Ethernet interface of [802.3-2002]. An Ethernet OAM protocol data unit is a valid Ethernet frame with a destination MAC address equal to the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), a lengthOrType field equal to the reserved type for Slow Protocols, and a Slow Protocols subtype equal to that of the subtype reserved for Ethernet OAM. OAMPDU is used throughout this document as an abbreviation for Ethernet OAM protocol data unit. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Std 802.3ah-2004: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan are networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', October 2004. [802.3-2002] refers to: IEEE Std 802.3-2002: 'Information technology - Telecommunications and information exchange between systems - Local and metropolitan are networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', March 2002. [802.3-2005] refers to: IEEE Std 802.3-2002: 'Information technology - Telecommunications and information exchange between systems - Local and metropolitan are networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', December 2005. [802-2001] refers to: 'IEEE Standard for LAN/MAN (Local Area Network/Metropolitan Area Network): Overview and Architecture', IEEE 802, June 2001.
INT cdot3OamMode	1.3.6.1.4.1.9.10.136.1.1.1.3	INTEGER	read-write	This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot. The default value of cdot3OamMode is dependent on the type of system on which this Ethernet like interface resides. The default value should be 'active(1)' unless it is known that this system should take on a subservient role to the other device connected over this interface. Changing this value results in incrementing the configuration revision field of locally generated OAMPDUs (30.3.6.1.12) and potentially re-doing the OAM discovery process if the cdot3OamOperStatus was already operational(9).
NTF cdot3OamNonThresholdEvent	1.3.6.1.4.1.9.10.136.0.2			A cdot3OamNonThresholdEvent notification is sent when a local or remote non-threshold crossing event is detected. A local event is detected by the local entity, while a remote event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a non-threshold crossing event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of the cdot3OamEventLogTable. The management entity should periodically check cdot3OamEventLogTable to detect any missed events.
cdot3OamNotificationGroup	1.3.6.1.4.1.9.10.136.2.1.11			A collection of notifications used by Ethernet OAM to signal to a management entity that local or remote events have occurred on a specified Ethernet link.
cdot3OamNotifications	1.3.6.1.4.1.9.10.136.0
cdot3OamObjects	1.3.6.1.4.1.9.10.136.1
INT cdot3OamOperStatus	1.3.6.1.4.1.9.10.136.1.1.1.2	INTEGER	read-only	At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this initialization is controlled by the OAM sublayer. This value is always disabled(1) if OAM is disabled on this interface via the cdot3OamAdminState. If the link has detected a fault and is transmitting OAMPDUs with a link fault indication, the value is linkFault(2). Also, if the interface is not operational (ifOperStatus is not up(1)), linkFault(2) is returned. Note that the object ifOperStatus may not be up(1) as a result of link failure or administrative action (ifAdminState being down(2) or testing(3)). The passiveWait(3) state is returned only by OAM entities in passive mode (cdot3OamMode) and reflects the state in which the OAM entity is waiting to see if the peer device is OAM capable. The activeSendLocal(4) value is used by active mode devices (cdot3OamMode) and reflects the OAM entity actively trying to discover whether the peer has OAM capability but has not yet made that determination. The state sendLocalAndRemote(5) reflects that the local OAM entity has discovered the peer but has not yet accepted or rejected the configuration of the peer. The local device can, for whatever reason, decide that the peer device is unacceptable and decline OAM peering. If the local OAM entity rejects the peer OAM entity, the state becomes oamPeeringLocallyRejected(7). If the OAM peering is allowed by the local device, the state moves to sendLocalAndRemoteOk(6). Note that both the sendLocalAndRemote(5) and oamPeeringLocallyRejected(7) states fall within the state SEND_LOCAL_REMOTE of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the local OAM client has actively rejected the peering or has just not indicated any decision yet. Whether a peering decision has been made is indicated via the local flags field in the OAMPDU (reflected in the aOAMLocalFlagsField of 30.3.6.1.10). If the remote OAM entity rejects the peering, the state becomes oamPeeringRemotelyRejected(8). Note that both the sendLocalAndRemoteOk(6) and oamPeeringRemotelyRejected(8) states fall within the state SEND_LOCAL_REMOTE_OK of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the remote OAM client has rejected the peering or has just not yet decided. This is indicated via the remote flags field in the OAM PDU (reflected in the aOAMRemoteFlagsField of 30.3.6.1.11). When the local OAM entity learns that both it and the remote OAM entity have accepted the peering, the state moves to operational(9) corresponding to the SEND_ANY state of the Discovery state diagram [802.3ah, Figure 57-5]. Since Ethernet OAM functions are not designed to work completely over half-duplex interfaces, the value nonOperHalfDuplex(10) is returned whenever Ethernet OAM is enabled (cdot3OamAdminState is enabled(1)) but the interface is in half-duplex operation.
C32 cdot3OamOrgSpecificRx	1.3.6.1.4.1.9.10.136.1.4.1.14	Counter32	read-only	A count of the number of Organization Specific OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamOrgSpecificTx	1.3.6.1.4.1.9.10.136.1.4.1.13	Counter32	read-only	A count of the number of Organization Specific OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
U32 cdot3OamPeerConfigRevision	1.3.6.1.4.1.9.10.136.1.2.1.6	Unsigned32	read-only	The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. The configuration revision can be determined from the Revision field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. A value of zero is returned if no Local Information TLV has been received.
cdot3OamPeerEntry	1.3.6.1.4.1.9.10.136.1.2.1		not-accessible	An entry in the table, containing information on the peer OAM entity for a single Ethernet like interface. Note that there is at most one OAM peer for each Ethernet like interface. Entries are automatically created when information about the OAM peer entity becomes available, and automatically deleted when the OAM peer entity is no longer in communication. Peer information is not available when cdot3OamOperStatus is disabled(1), linkFault(2), passiveWait(3), activeSendLocal(4). or nonOperHalfDuplex(10)).
BIT cdot3OamPeerFunctionsSupported	1.3.6.1.4.1.9.10.136.1.2.1.7	Bits	read-only	The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initialized so all bits are clear. If unidirectionalSupport(0) is set, then the peer OAM entity supports sending OAM frames on Ethernet interfaces when the receive path is known to be inoperable. If loopbackSupport(1) is set, then the peer OAM entity can send and receive OAM loopback commands. If eventSupport(2) is set, then the peer OAM entity can send and receive event OAMPDUs to signal various error conditions. If variableSupport(3) is set, then the peer OAM entity can send and receive variable requests to monitor attribute value as described in Clause 57 of [802.3ah]. The capabilities of the OAM peer can be determined from the configuration field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. All zeros are returned if no Local Information TLV has yet been received.
cdot3OamPeerGroup	1.3.6.1.4.1.9.10.136.2.1.2			A collection of objects providing the abilities, configuration, and status of a peer Ethernet OAM entity.
MAC cdot3OamPeerMacAddress	1.3.6.1.4.1.9.10.136.1.2.1.1	MacAddress	read-only	The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU.
U32 cdot3OamPeerMaxOamPduSize	1.3.6.1.4.1.9.10.136.1.2.1.5	Unsigned32	read-only	The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined from the PDU Configuration field of the Local Information TLV of the last Information OAMPDU received from the peer. A value of zero is returned if no Local Information TLV has been received. Otherwise, the value of the OAM peer's maximum OAMPDU size is returned in this value. Note that the values 1..63 are invalid sizes for Ethernet frames and should never appear.
INT cdot3OamPeerMode	1.3.6.1.4.1.9.10.136.1.2.1.4	INTEGER	read-only	The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from the peer. The value is unknown(3) whenever no Local Information TLV has been received. The values of active(1) and passive(2) are returned when a Local Information TLV has been received indicating the peer is in active or passive mode, respectively.
cdot3OamPeerTable	1.3.6.1.4.1.9.10.136.1.2		not-accessible	This table contains information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on Ethernet links on which OAM is enabled and operating properly. There is one entry in this table for each entry in the cdot3OamTable for which information on the peer OAM entity is available.
U32 cdot3OamPeerVendorInfo	1.3.6.1.4.1.9.10.136.1.2.1.3	Unsigned32	read-only	The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additional information about the peer entity. The format of the vendor information is unspecified within the 32-bit field. This value is initialized to zero before any Local Information TLV is received.
CDO cdot3OamPeerVendorOui	1.3.6.1.4.1.9.10.136.1.2.1.2	Cdot3Oui	read-only	The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to zero before any Local Information TLV is received.
cdot3OamStatsBaseGroup	1.3.6.1.4.1.9.10.136.2.1.3			A collection of objects providing the statistics for the number of various transmit and receive events for OAM on an Ethernet like interface. Note that all of these counters must be supported even if the related function (as described in cdot3OamFunctionsSupported) is not supported.
cdot3OamStatsEntry	1.3.6.1.4.1.9.10.136.1.4.1		not-accessible	An entry in the table, containing statistics information on the Ethernet OAM function for a single Ethernet like interface. Entries are automatically created for every entry in the cdot3OamTable. Counters are maintained across transitions in cdot3OamOperStatus.
cdot3OamStatsTable	1.3.6.1.4.1.9.10.136.1.4		not-accessible	This table contains statistics for the OAM function on a particular Ethernet like interface. There is an entry in the table for every entry in the cdot3OamTable. The counters in this table are defined as 32-bit entries to match the counter size as defined in [802.3ah]. Given the OAM protocol is a slow protocol, the counters increment at a slow rate.
cdot3OamTable	1.3.6.1.4.1.9.10.136.1.1		not-accessible	This table contains the primary controls and status for the OAM capabilities of an Ethernet like interface. There will be one row in this table for each Ethernet like interface in the system that supports the OAM functions defined in [802.3ah].
NTF cdot3OamThresholdEvent	1.3.6.1.4.1.9.10.136.0.1			A cdot3OamThresholdEvent notification is sent when a local or remote threshold crossing event is detected. A local threshold crossing event is detected by the local entity, while a remote threshold crossing event is detected by the reception of an Ethernet OAM Event Notification OAMPDU indicating a threshold event. This notification should not be sent more than once per second. The OAM entity can be derived from extracting the ifIndex from the variable bindings. The objects in the notification correspond to the values in a row instance of in the cdot3OamEventLogTable. The management entity should periodically check cdot3OamEventLogTable to detect any missed events.
C32 cdot3OamUniqueEventNotificationRx	1.3.6.1.4.1.9.10.136.1.4.1.4	Counter32	read-only	A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification receptions are counted by cdot3OamDuplicateEventNotificationRx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamUniqueEventNotificationTx	1.3.6.1.4.1.9.10.136.1.4.1.3	Counter32	read-only	A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Event Notification transmissions are counted by cdot3OamDuplicateEventNotificationTx. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamUnsupportedCodesRx	1.3.6.1.4.1.9.10.136.1.4.1.16	Counter32	read-only	A count of the number of OAMPDUs received on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamUnsupportedCodesTx	1.3.6.1.4.1.9.10.136.1.4.1.15	Counter32	read-only	A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamVariableRequestRx	1.3.6.1.4.1.9.10.136.1.4.1.10	Counter32	read-only	A count of the number of Variable Request OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamVariableRequestTx	1.3.6.1.4.1.9.10.136.1.4.1.9	Counter32	read-only	A count of the number of Variable Request OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamVariableResponseRx	1.3.6.1.4.1.9.10.136.1.4.1.12	Counter32	read-only	A count of the number of Variable Response OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
C32 cdot3OamVariableResponseTx	1.3.6.1.4.1.9.10.136.1.4.1.11	Counter32	read-only	A count of the number of Variable Response OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.

RFC description

Cisco MIB for IEEE 802.3ah Ethernet OAM (Operations, Administration, Maintenance) features on Ethernet interfaces.

Start monitoring Cisco switches and routers (802.3ah Ethernet OAM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DOT3-OAM-MIB