CISCO-DMN-DSG-MOIPINPUT-MIB

All MIBs › CISCO-DMN-DSG-MOIPINPUT-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2012-11-12

Category: Cisco Devices, Satellite

Description: Manages MPEG-over-IP input reception and stream acquisition parameters on the Cisco DMN D9800 satellite gateway.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DMN-DSG-MOIPINPUT-MIB?

CISCO-DMN-DSG-MOIPINPUT-MIB is a Cisco Digital Media Networking (DMN) MIB for the D9800 satellite/cable headend gateway family, specifically managing MPEG-over-IP (MOIP) input streams that the gateway receives and processes. It belongs to the broadcast/cable video distribution technology area and exposes configuration for how incoming transport-stream flows are acquired, including multicast addressing, forward error correction (FEC) mode and ports, source filtering, and de-jitter buffer behavior. For hardware/software status monitoring, it primarily surfaces stream-acquisition and signal-health parameters rather than classic CPU/memory metrics — an operator uses it to confirm an input flow is actually multicast, correctly filtered by source, and buffered with appropriate latency, which reflects the health of the incoming feed and the gateway's processing of it. It is a Cisco enterprise MIB likely used alongside other CISCO-DMN-DSG-* MIBs for the same platform rather than depending on standard IETF video MIBs. It is deployed in cable/satellite headend facilities where D9800 gateways ingest and redistribute IP video streams. Engineers can download the CISCO-DMN-DSG-MOIPINPUT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DMN-DSG-MOIPINPUT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco D9800 satellite/cable headend gateway
Cisco Digital Media Networking (DMN) equipment

Monitoring Examples

An engineer would poll moipInputTable/moipInputInfo per input to check moipInputFlowIsMulticast and moipInputFlowMulticastDstIPV4 to verify the expected multicast group is being received, and inspect moipInputFlowFecMode alongside moipInputFlowFec1UDPPort/moipInputFlowFec2UDPPort to confirm FEC packets are arriving on the right ports. Reading moipInputDejitterBufLatency against moipInputDejitterAlgorithm settings would reveal if buffering is misconfigured, causing picture stutter, and moipInputRednMode shows whether input redundancy/failover is active during a feed outage.

What Can Be Monitored

multicast input flow status
FEC mode and ports
source filter/selection
de-jitter buffer latency
input redundancy mode

Imported Objects

From CISCO-DMN-DSG-ROOT-MIB

ciscoDSGUtilities

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoDSGMOIPInput	1.3.6.1.4.1.1429.2.2.5.41			Cisco generic MOIP Input MIB.
moipInputInfo	1.3.6.1.4.1.1429.2.2.5.41.1
INT moipInputFlowIsMulticast	1.3.6.1.4.1.1429.2.2.5.41.1.1	INTEGER	read-write	Delivery Type: Multicast or Unicast.
IP moipInputFlowMulticastDstIPV4	1.3.6.1.4.1.1429.2.2.5.41.1.2	IpAddress	read-write	Muticast V4 IP Address.
INT moipInputFlowFecMode	1.3.6.1.4.1.1429.2.2.5.41.1.3	INTEGER	read-write	FEC Mode.
INT moipInputFlowSrcFilter	1.3.6.1.4.1.1429.2.2.5.41.1.4	INTEGER	read-write	Source Filtering Mode.
INT moipInputFlowTsUDPPort	1.3.6.1.4.1.1429.2.2.5.41.1.5	INTEGER	read-write	UDP Port for Transport Stream.
INT moipInputFlowFec1UDPPort	1.3.6.1.4.1.1429.2.2.5.41.1.6	INTEGER	read-write	UDP Port for FEC Columns Stream in step of 2.
INT moipInputFlowFec2UDPPort	1.3.6.1.4.1.1429.2.2.5.41.1.7	INTEGER	read-write	UDP Port for FEC Rows Stream in step of 2.
INT moipInputFlowSrcStrmSel	1.3.6.1.4.1.1429.2.2.5.41.1.8	INTEGER	read-write	Selects how to lock to source IP. In SwMap, first source present on both data ports is selected. In UserCfg, user selected source ip is locked per port.
INT moipInputDejitterAlgorithm	1.3.6.1.4.1.1429.2.2.5.41.1.9	INTEGER	read-write	Dejitter Algorithm.
INT moipInputDejitterBufLatency	1.3.6.1.4.1.1429.2.2.5.41.1.10	INTEGER	read-write	Dejitter Buffer Latency.
INT moipInputRednMode	1.3.6.1.4.1.1429.2.2.5.41.1.11	INTEGER	read-write	Input Redundancy Mode.
INT moipInputRednDir	1.3.6.1.4.1.1429.2.2.5.41.1.12	INTEGER	read-write	IPI Redundancy Switch Over Type.
INT moipInputRednDelayDir	1.3.6.1.4.1.1429.2.2.5.41.1.13	INTEGER	read-write	Direct Redundancy Switch Over Delay in msec.
INT moipInputRednDelRev	1.3.6.1.4.1.1429.2.2.5.41.1.14	INTEGER	read-write	Revertive Redundancy Switch Over Delay in sec.
STR moipInputRednPortInUse	1.3.6.1.4.1.1429.2.2.5.41.1.15	DisplayString	read-only	Redundancy: Port In use.
STR moipInputRednSwReason	1.3.6.1.4.1.1429.2.2.5.41.1.16	DisplayString	read-only	Reason for port Switch Over: None, Setup, EthLinkLoss, UdpLoss, PrgmLoss.
STR moipInputRednSwDateTime	1.3.6.1.4.1.1429.2.2.5.41.1.17	DisplayString	read-only	Redundancy: Switch Over date and time.
IP moipInputData1SelIPV4	1.3.6.1.4.1.1429.2.2.5.41.1.18	IpAddress	read-write	Select this host for DATA1 port. This object replaces moipInputSrcSelectData1Sel for backup and restore purpose and should not be used by any UIs.
IP moipInputData2SelIPV4	1.3.6.1.4.1.1429.2.2.5.41.1.19	IpAddress	read-write	Select this host for DATA2 port. This object replaces moipInputSrcSelectData2Sel for backup and restore purpose and should not be used by any UIs.
moipInputTable	1.3.6.1.4.1.1429.2.2.5.41.2
moipInputSrcSelectTable	1.3.6.1.4.1.1429.2.2.5.41.2.1		not-accessible	MOIP input source IP select table.
moipInputSrcSelectEntry	1.3.6.1.4.1.1429.2.2.5.41.2.1.1		not-accessible	Entry for source IP select table.
INT moipInputSrcSelectIdx	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.1	INTEGER	read-only	Host Index.
IP moipInputSrcSelectV4IPAddr	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.2	IpAddress	read-only	Host IP Address.
INT moipInputSrcSelectData1Sel	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.3	INTEGER	read-only	The host selected for DATA1 port. Use moipInputData1SelIPV4 to select.
INT moipInputSrcSelectData2Sel	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.4	INTEGER	read-only	The host selected for DATA2 port. Use moipInputData2SelIPV4 to select.
INT moipInputSrcSelectData1Avail	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.5	INTEGER	read-only	Stream from this host is present on DATA1 port.
INT moipInputSrcSelectData2Avail	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.6	INTEGER	read-only	Stream from this host is present on DATA2 port.
INT moipInputSrcSelectData1Enabled	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.7	INTEGER	read-only	This host can be selected for DATA1.
INT moipInputSrcSelectData2Enabled	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.8	INTEGER	read-only	This host can be selected for DATA2.
INT moipInputSrcSelectRowEnabled	1.3.6.1.4.1.1429.2.2.5.41.2.1.1.9	INTEGER	read-only	Rows disabled should be hidden from user.
moipInputSrcFilterTable	1.3.6.1.4.1.1429.2.2.5.41.2.2		not-accessible	MOIP input source IP filter table.
moipInputSrcFilterEntry	1.3.6.1.4.1.1429.2.2.5.41.2.2.1		not-accessible	Entry for source IP filter table.
INT moipInputSrcFilterIdx	1.3.6.1.4.1.1429.2.2.5.41.2.2.1.1	INTEGER	read-only	Source IP Filter Index.
IP moipInputSrcFilterV4IPAddr	1.3.6.1.4.1.1429.2.2.5.41.2.2.1.2	IpAddress	read-write	Source IP to be filtered.
ROW moipInputSrcFilterRowStatus	1.3.6.1.4.1.1429.2.2.5.41.2.2.1.3	RowStatus	read-write	Source Filter IP row status.
moipInputFlowTable	1.3.6.1.4.1.1429.2.2.5.41.2.3		not-accessible	DPM Configuration Table.
moipInputFlowEntry	1.3.6.1.4.1.1429.2.2.5.41.2.3.1		not-accessible	Entry for DPM global configuration table.
INT moipInputFlowID	1.3.6.1.4.1.1429.2.2.5.41.2.3.1.1	INTEGER	read-only	Flow ID.
INT moipInputFlowTsAct	1.3.6.1.4.1.1429.2.2.5.41.2.3.1.2	INTEGER	read-only	Flow Transport Stream Active.
INT moipInputFlowFecColStrmAct	1.3.6.1.4.1.1429.2.2.5.41.2.3.1.3	INTEGER	read-only	Flow FEC Column Stream Active.
INT moipInputFlowFecRowStrmAct	1.3.6.1.4.1.1429.2.2.5.41.2.3.1.4	INTEGER	read-only	Flow FEC Row Stream Active.

RFC description

Manages media over IP (MOIP) input configuration for Cisco digital set-top box platforms.

Start monitoring Cisco DMN D9800 digital satellite gateway with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DMN-DSG-MOIPINPUT-MIB

What Is CISCO-DMN-DSG-MOIPINPUT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description