All MIBs › CAMBIUM-PTP600-MIB
Organization: Cambium Networks Ltd.
Last Updated: 2012-12-17
Category: Vendor: Cambium Networks, Wireless and WLAN
Description: Manages Cambium Networks PTP 600 point-to-point licensed band wireless link configuration and throughput statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CAMBIUM-PTP600-MIB?
CAMBIUM-PTP600-MIB is a Cambium Networks enterprise MIB for the PTP 600 series, a 300 Mbps non-line-of-sight (NLOS) licensed/unlicensed-band wireless Ethernet bridge used for point-to-point links. Based on its stated scope it covers configuration and monitoring of the wireless bridge link, encompassing device identity/software information and radio link performance data such as throughput and signal statistics for the point-to-point connection. Its monitoring focus is on both link/software status and radio performance, letting an operator confirm the bridge link is up, check firmware version, and assess whether wireless throughput and signal quality meet expectations for the deployed link distance. No specific object names were available in the extracted data for this module, so no dependency or object-level detail beyond its stated purpose can be confirmed. It is deployed as a pair of units forming a fixed wireless Ethernet bridge, commonly for backhaul or building-to-building connectivity. Engineers can download the CAMBIUM-PTP600-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CAMBIUM-PTP600-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cambium PTP 600 wireless Ethernet bridge
Monitoring Examples
No sample objects were provided for this module, so a concrete polling scenario naming specific instance objects cannot be honestly constructed; based on its stated purpose, a realistic use would be periodically checking link throughput and signal-level style objects to confirm the NLOS wireless bridge is maintaining expected capacity, but the exact object names cannot be verified from the available data.
What Can Be Monitored
- link throughput
- signal/link quality
- device software/hardware version
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT accessMethod | 1.3.6.1.4.1.17713.6.5.16 | INTEGER | read-only | ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID. |
| I32 aggregateDataRate | 1.3.6.1.4.1.17713.6.20.3 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| alarms | 1.3.6.1.4.1.17713.6.13 | |||
| alarmsGroup | 1.3.6.1.4.1.17713.6.98.13 | The alarms object group. | ||
| I32 altitude | 1.3.6.1.4.1.17713.6.96.3 | Integer32 | read-write | The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function. |
| INT antennaGain | 1.3.6.1.4.1.17713.6.5.7 | INTEGER | read-write | Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna. |
| INT automaticTxPowerControl | 1.3.6.1.4.1.17713.6.10.8 | INTEGER | read-only | When enabled, the transmit power of the local end is automatically adjusted to maintain a configurable target receive signal level at the remote end of the link. When set to Enable with initial estimate, the Slave estimates the optional transmit power before it responds to the Master. |
| INT bandwidthVariant | 1.3.6.1.4.1.17713.6.8.6 | INTEGER | read-only | Bandwidth variant of the wireless unit |
| STR bootVersion | 1.3.6.1.4.1.17713.6.19.4 | DisplayString | read-only | Boot code software version |
| bridge | 1.3.6.1.4.1.17713.6.4 | |||
| bridgeGroup | 1.3.6.1.4.1.17713.6.98.4 | The bridge object group. | ||
| I32 byteErrorRatio | 1.3.6.1.4.1.17713.6.20.6 | Integer32 | read-only | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| INT cableLoss | 1.3.6.1.4.1.17713.6.5.8 | INTEGER | read-write | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| cambium | 1.3.6.1.4.1.17713 | MIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge. | ||
| INT channelACableLength | 1.3.6.1.4.1.17713.6.7.6 | INTEGER | read-only | The length of the cable connected to the telecoms interface, measured in feet |
| INT channelALineCode | 1.3.6.1.4.1.17713.6.7.4 | INTEGER | read-only | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| INT channelALoopback | 1.3.6.1.4.1.17713.6.7.8 | INTEGER | read-only | The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF channelALoopbackTrap | 1.3.6.1.4.1.17713.6.99.0.6 | The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT channelBandwidth | 1.3.6.1.4.1.17713.6.5.11 | INTEGER | read-only | This control sets the bandwidth of the transmit and receive radio channels |
| INT channelBCableLength | 1.3.6.1.4.1.17713.6.7.7 | INTEGER | read-only | The length of the cable connected to the telecoms interface, measured in feet |
| INT channelBLineCode | 1.3.6.1.4.1.17713.6.7.5 | INTEGER | read-only | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| INT channelBLoopback | 1.3.6.1.4.1.17713.6.7.9 | INTEGER | read-only | The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF channelBLoopbackTrap | 1.3.6.1.4.1.17713.6.99.0.7 | The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| configuration | 1.3.6.1.4.1.17713.6.5 | |||
| configurationGroup | 1.3.6.1.4.1.17713.6.98.5 | The configuration object group. | ||
| INT constantPowerSpectralDensity | 1.3.6.1.4.1.17713.6.8.7 | INTEGER | read-only | Constant power spectral density mode control |
| INT dataPortAutoMdix | 1.3.6.1.4.1.17713.6.6.3 | INTEGER | read-write | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| BIT dataPortAutoNegAdvertisement | 1.3.6.1.4.1.17713.6.6.2 | Bits | read-write | This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! |
| INT dataPortAutoNegotiation | 1.3.6.1.4.1.17713.6.6.1 | INTEGER | read-write | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. |
| INT dataPortConfigurationMismatch | 1.3.6.1.4.1.17713.6.13.9 | INTEGER | read-only | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch |
| NTF dataPortConfigurationMismatchTrap | 1.3.6.1.4.1.17713.6.99.0.19 | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch | ||
| INT dataPortDisabledWarning | 1.3.6.1.4.1.17713.6.13.7 | INTEGER | read-only | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic |
| NTF dataPortDisabledWarningTrap | 1.3.6.1.4.1.17713.6.99.0.17 | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic | ||
| INT dataPortFiberStatus | 1.3.6.1.4.1.17713.6.13.8 | INTEGER | read-only | If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert |
| NTF dataPortFiberStatusTrap | 1.3.6.1.4.1.17713.6.99.0.18 | If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include fiber support), the link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), or the link could not be established and LOS is detected (i.e. no optical carrier is detected). NB: a change of status may generate an SNMP trap and/or SMTP email alert | ||
| INT dataPortSpeedAndDuplex | 1.3.6.1.4.1.17713.6.6.5 | INTEGER | read-only | The current speed and duplex of the Ethernet link |
| INT dataPortStatus | 1.3.6.1.4.1.17713.6.6.4 | INTEGER | read-only | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF dataPortStatusTrap | 1.3.6.1.4.1.17713.6.99.0.3 | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT dataPortWirelessDownAlert | 1.3.6.1.4.1.17713.6.6.6 | INTEGER | read-write | When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. |
| INT daylightSaving | 1.3.6.1.4.1.17713.6.17.9 | INTEGER | read-write | Daylight Saving Time |
| dfs | 1.3.6.1.4.1.17713.6.3 | |||
| NTF dfsChannelChangeTrap | 1.3.6.1.4.1.17713.6.99.0.1 | DFS channel change event | ||
| dfsGroup | 1.3.6.1.4.1.17713.6.98.3 | The dfs object group. | ||
| NTF dfsImpulsiveInterferenceTrap | 1.3.6.1.4.1.17713.6.99.0.2 | DFS impulsive interference detected event | ||
| I32 dfsMeans | 1.3.6.1.4.1.17713.6.3.2.1.2 | Integer32 | read-only | Snapshot of DFS means |
| I32 dfsNineNinePointNinePercentiles | 1.3.6.1.4.1.17713.6.3.2.1.3 | Integer32 | read-only | Snapshot of DFS 99.9 percentiles |
| I32 dfsPeaks | 1.3.6.1.4.1.17713.6.3.2.1.4 | Integer32 | read-only | Snapshot of DFS peaks |
| dfsTable | 1.3.6.1.4.1.17713.6.3.2 | not-accessible | A table storing a snapshot of various DFS measurements for each channel | |
| dfsTableEntry | 1.3.6.1.4.1.17713.6.3.2.1 | not-accessible | Table DfsTable | |
| INT dfsTableIndex | 1.3.6.1.4.1.17713.6.3.2.1.1 | INTEGER | not-accessible | used to index values in the dfsTable. |
| INT dfsTableNumber | 1.3.6.1.4.1.17713.6.3.1 | INTEGER | read-only | Number of entries in the dfsTable |
| INT dSCPManagementPriority | 1.3.6.1.4.1.17713.6.6.26 | INTEGER | read-only | This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces |
| I32 eIRP | 1.3.6.1.4.1.17713.6.5.9 | Integer32 | read-only | Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm |
| BIT enabledDiagnosticAlarms | 1.3.6.1.4.1.17713.6.16.7 | Bits | read-write | Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes |
| encryption | 1.3.6.1.4.1.17713.6.22 | |||
| INT encryptionAlgorithm | 1.3.6.1.4.1.17713.6.22.1 | INTEGER | read-only | The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly |
| INT encryptionEnabledMismatch | 1.3.6.1.4.1.17713.6.13.3 | INTEGER | read-only | Encryption has been enabled on one end of the wireless link but not the other |
| NTF encryptionEnabledMismatchTrap | 1.3.6.1.4.1.17713.6.99.0.13 | Encryption has been enabled on one end of the wireless link but not the other | ||
| encryptionGroup | 1.3.6.1.4.1.17713.6.98.22 | The encryption object group. | ||
| ethernet | 1.3.6.1.4.1.17713.6.6 | |||
| INT ethernetBridgingAvailability | 1.3.6.1.4.1.17713.6.20.8 | INTEGER | read-only | Link availability bridging Ethernet traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| INT ethernetBridgingStatus | 1.3.6.1.4.1.17713.6.6.27 | INTEGER | read-only | Current status of Ethernet packet bridging over the wireless link |
| INT ethernetBridgingStatusAlarm | 1.3.6.1.4.1.17713.6.13.17 | INTEGER | read-only | Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode |
| NTF ethernetBridgingStatusAlarmTrap | 1.3.6.1.4.1.17713.6.99.0.35 | Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode | ||
| INT ethernetCappedMaxWirelessSpeed | 1.3.6.1.4.1.17713.6.5.10 | INTEGER | read-write | Ethernet frames will be discarded in the ODU if the data rate over the wireless link exceeds the Ethernet link speed at the local or remote Data port. The Ethernet Capped Max Wireless Speed control limits the wireless data rate based on the local and remote Ethernet link speed. Set this control to Enabled if either ODU is connected to an Ethernet link operating at less than 1000 Mbps. NB: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard. |
| INT ethernetFiberSupport | 1.3.6.1.4.1.17713.6.8.4 | INTEGER | read-only | Ethernet fiber support availability on this wireless unit |
| ethernetGroup | 1.3.6.1.4.1.17713.6.98.6 | The ethernet object group. | ||
| INT ethernetPriorityQueueMapping | 1.3.6.1.4.1.17713.6.6.15.1.2 | INTEGER | read-write | Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port |
| ethernetPriorityTable | 1.3.6.1.4.1.17713.6.6.15 | not-accessible | A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority. | |
| ethernetPriorityTableEntry | 1.3.6.1.4.1.17713.6.6.15.1 | not-accessible | Table EthernetPriorityTable | |
| INT ethernetPriorityTableIndex | 1.3.6.1.4.1.17713.6.6.15.1.1 | INTEGER | not-accessible | Ethernet priority flag, used to index values in the ethernetPriorityTable |
| INT ethernetPriorityTableNumber | 1.3.6.1.4.1.17713.6.6.14 | INTEGER | read-only | Number of entries in the vLANPriorityTable. |
| INT frequencyVariant | 1.3.6.1.4.1.17713.6.8.5 | INTEGER | read-only | Frequency variant of the wireless unit |
| IP gatewayIPAddress | 1.3.6.1.4.1.17713.6.5.3 | IpAddress | read-write | The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute |
| INT groupID | 1.3.6.1.4.1.17713.6.5.17 | INTEGER | read-write | When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group |
| STR hardwareVersion | 1.3.6.1.4.1.17713.6.19.2 | DisplayString | read-only | Hardware platform version |
| INT hAZLOCConfiguration | 1.3.6.1.4.1.17713.6.8.10 | INTEGER | read-only | The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key. |
| INT hTTPAccessEnabled | 1.3.6.1.4.1.17713.6.9.12 | INTEGER | read-write | This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) |
| INT hTTPPortNumber | 1.3.6.1.4.1.17713.6.9.14 | INTEGER | read-write | This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80) |
| INT hTTPSAccessEnabled | 1.3.6.1.4.1.17713.6.9.17 | INTEGER | read-write | This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) |
| INT hTTPSPortNumber | 1.3.6.1.4.1.17713.6.9.15 | INTEGER | read-write | This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443) |
| INT incompatibleMasterAndSlave | 1.3.6.1.4.1.17713.6.13.10 | INTEGER | read-only | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert |
| NTF incompatibleMasterAndSlaveTrap | 1.3.6.1.4.1.17713.6.99.0.20 | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert | ||
| INT incompatibleRegionCodes | 1.3.6.1.4.1.17713.6.13.4 | INTEGER | read-only | The master and slave units have incompatible region codes. NB: Both units must have compatible license keys |
| NTF incompatibleRegionCodesTrap | 1.3.6.1.4.1.17713.6.99.0.14 | The master and slave units have incompatible region codes. NB: Both units must have compatible license keys | ||
| INT installArmState | 1.3.6.1.4.1.17713.6.9.4 | INTEGER | read-only | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF installArmStateTrap | 1.3.6.1.4.1.17713.6.99.0.10 | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT installStatus | 1.3.6.1.4.1.17713.6.9.3 | INTEGER | read-only | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert |
| NTF installStatusTrap | 1.3.6.1.4.1.17713.6.99.0.9 | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert | ||
| IP iPAddress | 1.3.6.1.4.1.17713.6.5.1 | IpAddress | read-write | Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute. |
| INT iPDSCPPriorityQueueMapping | 1.3.6.1.4.1.17713.6.6.19.1.2 | INTEGER | read-write | Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port |
| iPDSCPPriorityTable | 1.3.6.1.4.1.17713.6.6.19 | not-accessible | A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority. | |
| iPDSCPPriorityTableEntry | 1.3.6.1.4.1.17713.6.6.19.1 | not-accessible | Table IPDSCPPriorityTable | |
| INT iPDSCPPriorityTableIndex | 1.3.6.1.4.1.17713.6.6.19.1.1 | INTEGER | not-accessible | IP DSCP priority flag, used to index values in the iPDSCPPriorityTable |
| INT iPDSCPPriorityTableNumber | 1.3.6.1.4.1.17713.6.6.18 | INTEGER | read-only | Number of entries in the iPDSCPPriorityTable. |
| INT l2CPPriorityQueueMapping | 1.3.6.1.4.1.17713.6.6.17.1.2 | INTEGER | read-write | Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port |
| l2CPPriorityTable | 1.3.6.1.4.1.17713.6.6.17 | not-accessible | A priority queue mapping table. This is a list of packet queues indexed by L2CP priority. | |
| l2CPPriorityTableEntry | 1.3.6.1.4.1.17713.6.6.17.1 | not-accessible | Table L2CPPriorityTable | |
| INT l2CPPriorityTableIndex | 1.3.6.1.4.1.17713.6.6.17.1.1 | INTEGER | not-accessible | L2CP priority flag, used to index values in the l2CPPriorityTable |
| INT l2CPPriorityTableNumber | 1.3.6.1.4.1.17713.6.6.16 | INTEGER | read-only | Number of entries in the l2CPPriorityTable. |
| STR latitude | 1.3.6.1.4.1.17713.6.96.2 | DisplayString | read-write | The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| licence | 1.3.6.1.4.1.17713.6.8 | |||
| licenceGroup | 1.3.6.1.4.1.17713.6.98.8 | The licence object group. | ||
| INT linkLoss | 1.3.6.1.4.1.17713.6.12.5 | INTEGER | read-only | The wireless link loss expressed in tenths of a dB |
| INT linkModeOptimisation | 1.3.6.1.4.1.17713.6.10.2 | INTEGER | read-only | Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols. |
| INT linkModeOptimizationMismatch | 1.3.6.1.4.1.17713.6.13.14 | INTEGER | read-only | The remote node of this link has been configured with a different link mode optimization |
| NTF linkModeOptimizationMismatchTrap | 1.3.6.1.4.1.17713.6.99.0.25 | The remote node of this link has been configured with a different link mode optimization | ||
| STR linkName | 1.3.6.1.4.1.17713.6.5.14 | DisplayString | read-write | Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link. |
| INT linkSymmetry | 1.3.6.1.4.1.17713.6.10.1 | INTEGER | read-only | Link Symmetry: in fixed symmetric mode the master spends an equal amount of time transmitting and receiving; in fixed asymmetric modes the master transmit and receive times have a fixed ratio; in adaptive mode the transmit and receive periods adjust with applied load. |
| INT localPacketFiltering | 1.3.6.1.4.1.17713.6.4.1 | INTEGER | read-write | When Local Packet Filtering is Enabled, the bridge learns the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and only bridges packets to the remote unit if the destination MAC address has not been learnt as a 'local' device. When Local Packet Filtering is Disabled then the bridge does not learn the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and bridges ALL Ethernet packets received to the remote unit. Local Packet Filtering should be enabled if no external routing hardware is present |
| STR longitude | 1.3.6.1.4.1.17713.6.96.1 | DisplayString | read-write | The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| management | 1.3.6.1.4.1.17713.6.9 | |||
| managementGroup | 1.3.6.1.4.1.17713.6.98.9 | The management object group. | ||
| INT managementMode | 1.3.6.1.4.1.17713.6.6.22 | INTEGER | read-only | Out-of-Band Management (only available on certain hardware models): End-to-end out-of-band mode in which the management agent can be reached from the management port at the local ODU and (assuming that the wireless link is established) the management port at the remote ODU. Out-of-Band Local Management (only available on certain hardware models): Similar to the standard Out-of-Band mode, except that management frames are not forwarded over the wireless link. In-Band Management (default): The management agent can be reached from the data port at the local ODU and (assuming that the wireless link is established) the data port at the remote ODU. In this mode the management port is disabled. In-Band Local Management (only available when 'Use VLAN For Management Interfaces' configures a VLAN tag): Similar to the standard In-Band mode, except that management frames are not forwarded over the wireless link. |
| INT managementPortConfigurationMismatch | 1.3.6.1.4.1.17713.6.13.15 | INTEGER | read-only | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. |
| NTF managementPortConfigurationMismatchTrap | 1.3.6.1.4.1.17713.6.99.0.28 | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. | ||
| INT managementPortDisabledWarning | 1.3.6.1.4.1.17713.6.13.12 | INTEGER | read-only | The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic |
| NTF managementPortDisabledWarningTrap | 1.3.6.1.4.1.17713.6.99.0.24 | The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic | ||
| INT managementPortSpeedAndDuplex | 1.3.6.1.4.1.17713.6.6.13 | INTEGER | read-only | The current speed and duplex of the out-of-band management link |
| INT managementPortStatus | 1.3.6.1.4.1.17713.6.6.12 | INTEGER | read-only | Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF managementPortStatusTrap | 1.3.6.1.4.1.17713.6.99.0.23 | Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT managementPortWirelessDownAlert | 1.3.6.1.4.1.17713.6.6.23 | INTEGER | read-only | When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. |
| INT masterSlaveMode | 1.3.6.1.4.1.17713.6.5.5 | INTEGER | read-write | The PTP wireless link operates using a master and slave relationship |
| INT maximumTransmitPower | 1.3.6.1.4.1.17713.6.5.6 | INTEGER | read-only | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link |
| INT mPLSTCPriorityQueueMapping | 1.3.6.1.4.1.17713.6.6.21.1.2 | INTEGER | read-write | Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port |
| mPLSTCPriorityTable | 1.3.6.1.4.1.17713.6.6.21 | not-accessible | A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority. | |
| mPLSTCPriorityTableEntry | 1.3.6.1.4.1.17713.6.6.21.1 | not-accessible | Table MPLSTCPriorityTable | |
| INT mPLSTCPriorityTableIndex | 1.3.6.1.4.1.17713.6.6.21.1.1 | INTEGER | not-accessible | MPLS TC priority flag, used to index values in the mPLSTCPriorityTable |
| INT mPLSTCPriorityTableNumber | 1.3.6.1.4.1.17713.6.6.20 | INTEGER | read-only | Number of entries in the mPLSTCPriorityTable. |
| notificationsGroup | 1.3.6.1.4.1.17713.6.98.99 | The notifications group. | ||
| INT noWirelessChannelAvailable | 1.3.6.1.4.1.17713.6.13.5 | INTEGER | read-only | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| NTF noWirelessChannelAvailableTrap | 1.3.6.1.4.1.17713.6.99.0.15 | Spectrum Management was unable to locate a suitable wireless channel to operate on | ||
| phyControl | 1.3.6.1.4.1.17713.6.10 | |||
| phyControlGroup | 1.3.6.1.4.1.17713.6.98.10 | The phyControl object group. | ||
| phyStatus | 1.3.6.1.4.1.17713.6.12 | |||
| phyStatusGroup | 1.3.6.1.4.1.17713.6.98.12 | The phyStatus object group. | ||
| STR productName | 1.3.6.1.4.1.17713.6.8.3 | DisplayString | read-only | Name of the product variant |
| INT productVariant | 1.3.6.1.4.1.17713.6.8.2 | INTEGER | read-only | The product variant |
| ptmp | 1.3.6.1.4.1.17713.2 | |||
| ptp | 1.3.6.1.4.1.17713.1 | |||
| ptp600 | 1.3.6.1.4.1.17713.6 | |||
| ptpCompliance | 1.3.6.1.4.1.17713.6.97 | The compliance statement for the Cambium PTP MIB | ||
| ptpGroups | 1.3.6.1.4.1.17713.6.98 | |||
| ptpTrapPrefix | 1.3.6.1.4.1.17713.6.99.0 | |||
| ptpTraps | 1.3.6.1.4.1.17713.6.99 | |||
| pubStats | 1.3.6.1.4.1.17713.6.20 | |||
| pubStatsGroup | 1.3.6.1.4.1.17713.6.98.20 | The pubStats object group. | ||
| INT qOSPriorityScheme | 1.3.6.1.4.1.17713.6.6.24 | INTEGER | read-write | Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLS |
| I32 range | 1.3.6.1.4.1.17713.6.12.4 | Integer32 | read-only | Distance between the two peer wireless units expressed in tenths of a kilometer |
| INT rangingMode | 1.3.6.1.4.1.17713.6.9.2 | INTEGER | read-only | Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range |
| I32 rawReceivePower | 1.3.6.1.4.1.17713.6.12.17 | Integer32 | read-only | Raw receive power expressed in tenths of a dBm |
| INT receiveChannel | 1.3.6.1.4.1.17713.6.12.6 | INTEGER | read-only | Current active receive channel |
| I32 receiveDataRate | 1.3.6.1.4.1.17713.6.20.1 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| INT receiveFreqKHz | 1.3.6.1.4.1.17713.6.12.14 | INTEGER | read-only | Current receive frequency expressed as KHz |
| INT receiveFreqMHz | 1.3.6.1.4.1.17713.6.12.11 | INTEGER | read-only | Current receive frequency expressed in integer MHz |
| INT receiveModulationMode | 1.3.6.1.4.1.17713.6.12.8 | INTEGER | read-only | Current active receive modulation mode |
| INT receiveModulationModeDetail | 1.3.6.1.4.1.17713.6.20.7 | INTEGER | read-only | The reason for the current receive modulation mode |
| I32 receivePower | 1.3.6.1.4.1.17713.6.12.1 | Integer32 | read-only | Receive power expressed in tenths of a dBm |
| INT regionCode | 1.3.6.1.4.1.17713.6.8.1 | INTEGER | read-only | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF regionCodeTrap | 1.3.6.1.4.1.17713.6.99.0.8 | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| IP remoteIPAddress | 1.3.6.1.4.1.17713.6.5.12 | IpAddress | read-only | IP Address of the peer wireless unit |
| INT remoteMaximumTransmitPower | 1.3.6.1.4.1.17713.6.10.4 | INTEGER | read-only | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| INT remoteRxTargetPower | 1.3.6.1.4.1.17713.6.10.9 | INTEGER | read-only | This is the target receive level for the end of the link which is remote from the end being configured. When Automatic Power Control is enabled, the transmit power of the local end is automatically adjusted in order to maintain the receive signal level at the remote end within a range centered on this value |
| reset | 1.3.6.1.4.1.17713.6.18 | |||
| resetGroup | 1.3.6.1.4.1.17713.6.98.18 | The reset object group. | ||
| INT rxColorCode | 1.3.6.1.4.1.17713.6.10.6 | INTEGER | read-only | Receive Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link. |
| INT searchState | 1.3.6.1.4.1.17713.6.12.16 | INTEGER | read-only | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal. |
| STR secondarySoftwareVersion | 1.3.6.1.4.1.17713.6.19.3 | DisplayString | read-only | Secondary software version, used when the primary software image is invalid or erased |
| INT secureModeAlarm | 1.3.6.1.4.1.17713.6.13.16 | INTEGER | read-only | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image. |
| NTF secureModeAlarmTrap | 1.3.6.1.4.1.17713.6.99.0.34 | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image. | ||
| INT securityLevel | 1.3.6.1.4.1.17713.6.8.11 | INTEGER | read-only | The maximum configurable security level |
| I32 signalStrengthRatio | 1.3.6.1.4.1.17713.6.12.13 | Integer32 | read-only | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB |
| STR siteName | 1.3.6.1.4.1.17713.6.5.15 | DisplayString | read-write | This field contains a user-provided description of the site name together with any additional notes |
| smtp | 1.3.6.1.4.1.17713.6.15 | |||
| STR sMTPDestinationEmailAddress | 1.3.6.1.4.1.17713.6.15.5 | DisplayString | read-write | The 'to' email address used when constructing the automatically generated e-mail message |
| INT sMTPEmailAlert | 1.3.6.1.4.1.17713.6.15.1 | INTEGER | read-write | Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address |
| BIT sMTPEnabledMessages | 1.3.6.1.4.1.17713.6.15.6 | Bits | read-write | This controls which SMTP messages the unit will send |
| smtpGroup | 1.3.6.1.4.1.17713.6.98.15 | The smtp object group. | ||
| IP sMTPServerIPAddress | 1.3.6.1.4.1.17713.6.15.2 | IpAddress | read-write | IP address of the SMTP server |
| INT sMTPServerPortNumber | 1.3.6.1.4.1.17713.6.15.3 | INTEGER | read-write | Port number of the SMTP server |
| STR sMTPSourceEmailAddress | 1.3.6.1.4.1.17713.6.15.4 | DisplayString | read-write | The 'from' email address used when constructing the automatically generated e-mail message |
| STR sNMPCommunityString | 1.3.6.1.4.1.17713.6.16.2 | DisplayString | read-write | The SNMP community string. NB: A system reboot is required to activate changes to this attribute |
| snmpControl | 1.3.6.1.4.1.17713.6.16 | |||
| snmpControlGroup | 1.3.6.1.4.1.17713.6.98.16 | The snmpControl object group. | ||
| BIT sNMPEnabledTraps | 1.3.6.1.4.1.17713.6.16.6 | Bits | read-write | This controls which SNMP Traps the unit will send |
| INT sNMPPortNumber | 1.3.6.1.4.1.17713.6.16.1 | INTEGER | read-write | The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute |
| IP sNMPTrapIPAddress | 1.3.6.1.4.1.17713.6.16.4.1.2 | IpAddress | read-write | The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute. |
| INT sNMPTrapPortNumber | 1.3.6.1.4.1.17713.6.16.4.1.3 | INTEGER | read-write | Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute. |
| sNMPTrapTable | 1.3.6.1.4.1.17713.6.16.4 | not-accessible | SNMP trap configuration table. | |
| sNMPTrapTableEntry | 1.3.6.1.4.1.17713.6.16.4.1 | not-accessible | Table SNMPTrapTable | |
| INT sNMPTrapTableIndex | 1.3.6.1.4.1.17713.6.16.4.1.1 | INTEGER | not-accessible | SNMP trap value, used to index the SNMPTrapTable. |
| INT sNMPTrapTableNumber | 1.3.6.1.4.1.17713.6.16.3 | INTEGER | read-only | Number of entries in the sNMPTrapTable. |
| INT sNMPTrapVersion | 1.3.6.1.4.1.17713.6.16.5 | INTEGER | read-write | The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute |
| INT sNMPv3Enable | 1.3.6.1.4.1.17713.6.8.9 | INTEGER | read-only | SNMPv3 availability control |
| sntp | 1.3.6.1.4.1.17713.6.17 | |||
| sntpGroup | 1.3.6.1.4.1.17713.6.98.17 | The sntp object group. | ||
| I32 sNTPLastSync | 1.3.6.1.4.1.17713.6.17.6 | Integer32 | read-only | Last SNTP sync time |
| INT sNTPPollInterval | 1.3.6.1.4.1.17713.6.17.4 | INTEGER | read-write | The SNTP server polling interval |
| INT sNTPPrimaryServer | 1.3.6.1.4.1.17713.6.17.10 | INTEGER | read-write | Specifies the primary SNTP server, determining the order in which the servers are tried. |
| INT sNTPPrimaryServerDeadTime | 1.3.6.1.4.1.17713.6.17.11 | INTEGER | read-write | Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer. |
| IP sNTPServerIPAddress | 1.3.6.1.4.1.17713.6.17.15.1.2 | IpAddress | read-write | The IP address of a valid SNTP server |
| INT sNTPServerPortNumber | 1.3.6.1.4.1.17713.6.17.15.1.3 | INTEGER | read-write | The IP port number of the SNTP server. Defaults to port 123. |
| INT sNTPServerRetries | 1.3.6.1.4.1.17713.6.17.12 | INTEGER | read-write | Number of times the PTP will retry after an SNTP server fails to respond. |
| STR sNTPServerStatus | 1.3.6.1.4.1.17713.6.17.15.1.4 | DisplayString | read-only | Status message reflecting the state of communications with the SNTP server |
| sNTPServerTable | 1.3.6.1.4.1.17713.6.17.15 | not-accessible | ||
| sNTPServerTableEntry | 1.3.6.1.4.1.17713.6.17.15.1 | not-accessible | Table SNTPServerTable | |
| INT sNTPServerTableIndex | 1.3.6.1.4.1.17713.6.17.15.1.1 | INTEGER | not-accessible | Index range for the SNTPServerTable. |
| INT sNTPServerTableNumber | 1.3.6.1.4.1.17713.6.17.14 | INTEGER | read-only | Number of entries in the SNTPServerTable. |
| INT sNTPServerTimeout | 1.3.6.1.4.1.17713.6.17.13 | INTEGER | read-write | Time (in seconds) the PTP will wait for a response from an SNTP server. |
| INT sNTPState | 1.3.6.1.4.1.17713.6.17.1 | INTEGER | read-write | SNTP control state |
| INT sNTPSync | 1.3.6.1.4.1.17713.6.17.5 | INTEGER | read-only | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP |
| NTF sNTPSyncTrap | 1.3.6.1.4.1.17713.6.99.0.21 | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP | ||
| STR softwareVersion | 1.3.6.1.4.1.17713.6.19.1 | DisplayString | read-only | Current software version |
| IP subnetMask | 1.3.6.1.4.1.17713.6.5.2 | IpAddress | read-write | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute |
| supplementary | 1.3.6.1.4.1.17713.6.96 | |||
| supplementaryGroup | 1.3.6.1.4.1.17713.6.98.96 | The supplementary object group. | ||
| INT syslogClient | 1.3.6.1.4.1.17713.6.24.1 | INTEGER | read-only | Enable or disable the syslog client |
| NTF syslogClientTrap | 1.3.6.1.4.1.17713.6.99.0.33 | Enable or disable the syslog client | ||
| syslogControl | 1.3.6.1.4.1.17713.6.24 | |||
| syslogControlGroup | 1.3.6.1.4.1.17713.6.98.24 | The syslogControl object group. | ||
| NTF syslogLocalNearlyFullTrap | 1.3.6.1.4.1.17713.6.99.0.31 | The syslog local log is nearly full (90%) | ||
| NTF syslogLocalWrappedTrap | 1.3.6.1.4.1.17713.6.99.0.32 | The syslog local log has wrapped | ||
| INT syslogState | 1.3.6.1.4.1.17713.6.24.2 | INTEGER | read-only | The syslog service has been enabled or disabled |
| NTF syslogStateTrap | 1.3.6.1.4.1.17713.6.99.0.30 | The syslog service has been enabled or disabled | ||
| I32 systemClock | 1.3.6.1.4.1.17713.6.17.7 | Integer32 | read-only | System clock presented as local time |
| INT systemReset | 1.3.6.1.4.1.17713.6.18.1 | INTEGER | read-write | Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory |
| OCT targetMACAddress | 1.3.6.1.4.1.17713.6.5.4 | OCTET STRING | read-only | MAC address of the PTP wireless unit forming the other end of the PTP link |
| INT targetRange | 1.3.6.1.4.1.17713.6.9.1 | INTEGER | read-only | Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0 |
| tDDControl | 1.3.6.1.4.1.17713.6.23 | |||
| tDDControlGroup | 1.3.6.1.4.1.17713.6.98.23 | The tDDControl object group. | ||
| INT tDDSynchronizationAlarm | 1.3.6.1.4.1.17713.6.13.13 | INTEGER | read-only | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. |
| NTF tDDSynchronizationAlarmTrap | 1.3.6.1.4.1.17713.6.99.0.22 | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. | ||
| INT tDDSynchronizationMode | 1.3.6.1.4.1.17713.6.23.1 | INTEGER | read-only | TDD Synchronization Mode selection |
| INT tDDSynchronizationStatus | 1.3.6.1.4.1.17713.6.13.11 | INTEGER | read-only | An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference. |
| telecom | 1.3.6.1.4.1.17713.6.7 | |||
| telecomGroup | 1.3.6.1.4.1.17713.6.98.7 | The telecom object group. | ||
| INT telecomsChannelAStatus | 1.3.6.1.4.1.17713.6.7.2 | INTEGER | read-only | Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF telecomsChannelAStatusTrap | 1.3.6.1.4.1.17713.6.99.0.4 | Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT telecomsChannelBStatus | 1.3.6.1.4.1.17713.6.7.3 | INTEGER | read-only | Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF telecomsChannelBStatusTrap | 1.3.6.1.4.1.17713.6.99.0.5 | Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT telecomsChannelSelection | 1.3.6.1.4.1.17713.6.7.10 | INTEGER | read-only | Indicates which telecoms channels have been enabled. If only Channel A has been enabled, then the Channel B attributes will be ignored. |
| INT telecomsInterface | 1.3.6.1.4.1.17713.6.7.1 | INTEGER | read-only | The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored. |
| INT telnetAccessEnabled | 1.3.6.1.4.1.17713.6.9.13 | INTEGER | read-write | This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled) |
| INT telnetPortNumber | 1.3.6.1.4.1.17713.6.9.16 | INTEGER | read-write | This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23) |
| IP tFTPServerIPAddress | 1.3.6.1.4.1.17713.6.9.5 | IpAddress | read-write | IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| INT tFTPServerPortNumber | 1.3.6.1.4.1.17713.6.9.6 | INTEGER | read-write | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| STR tFTPSoftwareUpgradeFileName | 1.3.6.1.4.1.17713.6.9.7 | DisplayString | read-write | Filename of the Software Upgrade to be loaded from the TFTP Server |
| INT tFTPSoftwareUpgradeStatus | 1.3.6.1.4.1.17713.6.9.9 | INTEGER | read-only | The current status of the TFTP Software upgrade process |
| STR tFTPSoftwareUpgradeStatusAdditionalText | 1.3.6.1.4.1.17713.6.9.11 | DisplayString | read-only | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| STR tFTPSoftwareUpgradeStatusText | 1.3.6.1.4.1.17713.6.9.10 | DisplayString | read-only | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| I32 tFTPStartSoftwareUpgrade | 1.3.6.1.4.1.17713.6.9.8 | Integer32 | read-write | Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (iDFS) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a region where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebooted |
| INT timeZone | 1.3.6.1.4.1.17713.6.17.8 | INTEGER | read-write | Time zone offsets from Greenwich Mean Time (GMT) |
| INT transmitChannel | 1.3.6.1.4.1.17713.6.12.7 | INTEGER | read-only | Current active transmit channel |
| I32 transmitDataRate | 1.3.6.1.4.1.17713.6.20.2 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| INT transmitFreqKHz | 1.3.6.1.4.1.17713.6.12.15 | INTEGER | read-only | Current transmit frequency expressed as KHz |
| INT transmitFreqMHz | 1.3.6.1.4.1.17713.6.12.12 | INTEGER | read-only | Current transmit frequency expressed in integer MHz |
| INT transmitModulationMode | 1.3.6.1.4.1.17713.6.12.9 | INTEGER | read-only | Current active transmit modulation mode |
| I32 transmitPower | 1.3.6.1.4.1.17713.6.12.3 | Integer32 | read-only | Transmit power expressed in tenths of a dBm |
| INT txColorCode | 1.3.6.1.4.1.17713.6.10.5 | INTEGER | read-only | Transmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link. |
| INT unitOutOfCalibration | 1.3.6.1.4.1.17713.6.13.1 | INTEGER | read-only | The unit is out of calibration |
| NTF unitOutOfCalibrationTrap | 1.3.6.1.4.1.17713.6.99.0.11 | The unit is out of calibration | ||
| INT unknownNetworkPriorityQueueMapping | 1.3.6.1.4.1.17713.6.6.25 | INTEGER | read-write | Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS |
| INT userConfiguredMaxModulationMode | 1.3.6.1.4.1.17713.6.10.3 | INTEGER | read-write | The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard |
| INT useVLANForManagementInterfaces | 1.3.6.1.4.1.17713.6.6.7 | INTEGER | read-write | This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot |
| I32 vectorError | 1.3.6.1.4.1.17713.6.12.2 | Integer32 | read-only | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB |
| versions | 1.3.6.1.4.1.17713.6.19 | |||
| versionsGroup | 1.3.6.1.4.1.17713.6.98.19 | The versions object group. | ||
| INT vLANManagementPriority | 1.3.6.1.4.1.17713.6.6.8 | INTEGER | read-write | This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| INT vLANManagementVID | 1.3.6.1.4.1.17713.6.6.11 | INTEGER | read-write | This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot |
| INT wirelessLinkAvailability | 1.3.6.1.4.1.17713.6.20.4 | INTEGER | read-only | Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| INT wirelessLinkDisabledWarning | 1.3.6.1.4.1.17713.6.13.6 | INTEGER | read-only | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic |
| NTF wirelessLinkDisabledWarningTrap | 1.3.6.1.4.1.17713.6.99.0.16 | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic | ||
| INT wirelessLinkStatus | 1.3.6.1.4.1.17713.6.20.5 | INTEGER | read-only | Current status of the wireless link |
RFC description
SNMP MIB for Cambium PTP 600 point-to-point wireless Ethernet bridges. Manages 300 Mbps wireless backhaul links operating in licensed frequency bands, supporting features like SNTP, syslog, DFS, SNMPv3, and Tx power control.
Start monitoring Cambium Networks PTP-series wireless Ethernet bridge with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.