UBNT-AirMAX-MIB

MIB Reference — IPNetwork Monitor · Updated October 06, 2026

All MIBs › UBNT-AirMAX-MIB

Organization: Ubiquiti Networks, Inc.

Last Updated: 2014-05-25

Category: Vendor: Ubiquiti, Wireless and WLAN

Description: Ubiquiti airMAX enterprise MIB for monitoring wireless radio statistics on airMAX point-to-point and point-to-multipoint outdoor wireless devices.

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring UBNT-AirMAX-MIB with a free 30-day trial of IPNetwork Monitor.

What Is UBNT-AirMAX-MIB?

UBNT-AirMAX-MIB is a Ubiquiti Networks vendor MIB for the airMAX line of outdoor point-to-point and point-to-multipoint wireless bridges (e.g. NanoBridge, Rocket, PowerBeam devices running airMAX firmware). It is intended to expose wireless radio statistics and link-quality data specific to the airMAX TDMA protocol, complementing standard interface counters with airMAX-specific radio metrics. In monitoring terms it is used to track wireless link health such as signal strength, noise floor, capacity/throughput utilization, and connection status between AP and station, which surfaces RF degradation or capacity exhaustion before it causes outages. It works alongside IF-MIB/MIB-II for basic interface counters and UBNT-UBIQUITI-MIB for general device identity, since this module is scoped to airMAX radio statistics only. It is typically deployed by WISPs and outdoor wireless network operators using NMS tools to watch backhaul and subscriber link quality. Engineers can download the UBNT-AirMAX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UBNT-AirMAX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Ubiquiti airMAX outdoor wireless bridge/radio

Monitoring Examples

No sample object names were provided for this module, so specific OID-level detail cannot be grounded; in practice an operator would expect tables of per-station or per-radio entries reporting signal-to-noise ratio, capacity percentage, and connection state, analogous to the airOS web UI's wireless statistics page. Because no sample_objects were supplied, this description is based on general knowledge of the airMAX product family rather than confirmed object names in this specific MIB file.

What Can Be Monitored

  • radio signal strength
  • noise floor
  • link capacity/throughput
  • station connection status

This MIB depends on

Related MIBs

Imported Objects

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
MacAddress
TruthValue

From UBNT-MIB

ubntAirosGroupsOBJECT-IDENTITY
ubntMIBMODULE-IDENTITY

How to Use in IPNetwork Monitor

Example using ubntStaTxBytes OID:

Select an Ubiquiti airMAX outdoor wireless bridge/radio (signal strength/noise-floor/capacity status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ubntStaTxBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports tX bytes. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

Ubiquiti Networks private MIB for AirMAX wireless access points, providing radio configuration, transmit power, and link statistics.

Start monitoring Ubiquiti airMAX outdoor wireless bridge/radio (signal strength/noise-floor/capacity status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UBNT-AirMAX-MIB