All MIBs › CAMBIUM-PTP500-MIB
Organization: Cambium Networks Ltd.
Last Updated: 2014-03-14
Category: Vendor: Cambium Networks, Wireless and WLAN
Description: Manages Cambium Networks PTP 500 point-to-point licensed microwave radio including link performance and adaptive modulation.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CAMBIUM-PTP500-MIB?
CAMBIUM-PTP500-MIB is a Cambium Networks Ltd. (enterprise OID 17713) proprietary MIB for the PTP 500 series 105Mbps non-line-of-sight (NLOS) wireless Ethernet bridge. Its objects cover a DFS (Dynamic Frequency Selection) table (means, 99.9th-percentiles, peaks), a VLAN-priority table, an SNMP-trap-destination table, a user table, IP address/subnet mask/gateway, target MAC address, master/slave mode, max transmit power, antenna gain, cable loss, EIRP, channel bandwidth, remote IP address, and link name. As a configuration/performance MIB it lets an administrator confirm RF power/gain settings and DFS radar-avoidance statistics on a Cambium PTP 500 wireless bridge. It is deployed on the Cambium Networks PTP 500 series wireless Ethernet bridge. Engineers can download the CAMBIUM-PTP500-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CAMBIUM-PTP500-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cambium Networks PTP 500 series wireless Ethernet bridge
Monitoring Examples
An administrator checks maximumTransmitPower and eIRP to confirm regulatory RF power compliance on a Cambium PTP 500 wireless Ethernet bridge.
What Can Be Monitored
- RF power/gain configuration and DFS statistics
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| aAAControl | 1.3.6.1.4.1.17713.5.25 | |||
| aAAControlGroup | 1.3.6.1.4.1.17713.5.98.25 | The aAAControl object group. | ||
| INT accessMethod | 1.3.6.1.4.1.17713.5.5.16 | INTEGER | read-only | This controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access) |
| I32 aggregateDataRate | 1.3.6.1.4.1.17713.5.20.3 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| alarms | 1.3.6.1.4.1.17713.5.13 | |||
| alarmsGroup | 1.3.6.1.4.1.17713.5.98.13 | The alarms object group. | ||
| I32 altitude | 1.3.6.1.4.1.17713.5.96.3 | Integer32 | read-write | The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function. |
| INT antennaGain | 1.3.6.1.4.1.17713.5.5.7 | INTEGER | read-write | Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna. |
| INT bandwidthVariant | 1.3.6.1.4.1.17713.5.8.6 | INTEGER | read-only | Bandwidth variant of the wireless unit |
| STR bootVersion | 1.3.6.1.4.1.17713.5.19.4 | DisplayString | read-only | Boot code software version |
| I32 byteErrorRatio | 1.3.6.1.4.1.17713.5.20.6 | Integer32 | read-only | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| INT cableLoss | 1.3.6.1.4.1.17713.5.5.8 | INTEGER | read-write | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| cambium | 1.3.6.1.4.1.17713 | MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge. | ||
| INT capacityLicenseMismatch | 1.3.6.1.4.1.17713.5.13.16 | INTEGER | read-only | The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit |
| NTF capacityLicenseMismatchTrap | 1.3.6.1.4.1.17713.5.99.0.27 | The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit | ||
| INT channelBandwidth | 1.3.6.1.4.1.17713.5.5.11 | INTEGER | read-only | This control sets the bandwidth of the transmit and receive radio channels |
| NTF channelChangeTrap | 1.3.6.1.4.1.17713.5.99.0.1 | The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference. | ||
| configuration | 1.3.6.1.4.1.17713.5.5 | |||
| configurationGroup | 1.3.6.1.4.1.17713.5.98.5 | The configuration object group. | ||
| INT constantPowerSpectralDensity | 1.3.6.1.4.1.17713.5.8.7 | INTEGER | read-only | Constant power spectral density mode control |
| INT dataPortAutoMdix | 1.3.6.1.4.1.17713.5.6.3 | INTEGER | read-write | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| BIT dataPortAutoNegAdvertisement | 1.3.6.1.4.1.17713.5.6.2 | Bits | read-write | This sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! |
| INT dataPortAutoNegotiation | 1.3.6.1.4.1.17713.5.6.1 | INTEGER | read-write | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. |
| INT dataPortConfigurationMismatch | 1.3.6.1.4.1.17713.5.13.9 | INTEGER | read-only | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch |
| NTF dataPortConfigurationMismatchTrap | 1.3.6.1.4.1.17713.5.99.0.19 | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch | ||
| INT dataPortDisabledWarning | 1.3.6.1.4.1.17713.5.13.7 | INTEGER | read-only | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic |
| NTF dataPortDisabledWarningTrap | 1.3.6.1.4.1.17713.5.99.0.17 | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic | ||
| INT dataPortSpeedAndDuplex | 1.3.6.1.4.1.17713.5.6.5 | INTEGER | read-only | The current speed and duplex of the Ethernet link |
| INT dataPortStatus | 1.3.6.1.4.1.17713.5.6.4 | INTEGER | read-only | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF dataPortStatusTrap | 1.3.6.1.4.1.17713.5.99.0.3 | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT dataPortWirelessDownAlert | 1.3.6.1.4.1.17713.5.6.6 | INTEGER | read-write | When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. |
| INT daylightSaving | 1.3.6.1.4.1.17713.5.17.9 | INTEGER | read-write | Daylight Saving Time |
| dfs | 1.3.6.1.4.1.17713.5.3 | |||
| dfsGroup | 1.3.6.1.4.1.17713.5.98.3 | The dfs object group. | ||
| NTF dfsImpulsiveInterferenceTrap | 1.3.6.1.4.1.17713.5.99.0.2 | DFS impulsive interference detected event | ||
| I32 dfsMeans | 1.3.6.1.4.1.17713.5.3.2.1.2 | Integer32 | read-only | Snapshot of DFS means |
| I32 dfsNineNinePointNinePercentiles | 1.3.6.1.4.1.17713.5.3.2.1.3 | Integer32 | read-only | Snapshot of DFS 99.9 percentiles |
| I32 dfsPeaks | 1.3.6.1.4.1.17713.5.3.2.1.4 | Integer32 | read-only | Snapshot of DFS peaks |
| dfsTable | 1.3.6.1.4.1.17713.5.3.2 | not-accessible | A table storing a snapshot of various DFS measurements for each channel | |
| dfsTableEntry | 1.3.6.1.4.1.17713.5.3.2.1 | not-accessible | Table DfsTable | |
| INT dfsTableIndex | 1.3.6.1.4.1.17713.5.3.2.1.1 | INTEGER | not-accessible | used to index values in the dfsTable. |
| INT dfsTableNumber | 1.3.6.1.4.1.17713.5.3.1 | INTEGER | read-only | Number of entries in the dfsTable |
| I32 eIRP | 1.3.6.1.4.1.17713.5.5.9 | Integer32 | read-only | Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm |
| BIT enabledDiagnosticAlarms | 1.3.6.1.4.1.17713.5.16.7 | Bits | read-write | Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes |
| encryption | 1.3.6.1.4.1.17713.5.22 | |||
| INT encryptionAlgorithm | 1.3.6.1.4.1.17713.5.22.1 | INTEGER | read-only | The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly |
| encryptionGroup | 1.3.6.1.4.1.17713.5.98.22 | The encryption object group. | ||
| ethernet | 1.3.6.1.4.1.17713.5.6 | |||
| INT ethernetFiberSupport | 1.3.6.1.4.1.17713.5.8.4 | INTEGER | read-only | Ethernet fiber support availability on this wireless unit |
| ethernetGroup | 1.3.6.1.4.1.17713.5.98.6 | The ethernet object group. | ||
| INT frequencyVariant | 1.3.6.1.4.1.17713.5.8.5 | INTEGER | read-only | Frequency variant of the wireless unit |
| IP gatewayIPAddress | 1.3.6.1.4.1.17713.5.5.3 | IpAddress | read-write | The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute |
| INT groupID | 1.3.6.1.4.1.17713.5.5.17 | INTEGER | read-only | When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platforms |
| STR hardwareVersion | 1.3.6.1.4.1.17713.5.19.2 | DisplayString | read-only | Hardware platform version |
| INT hTTPAccessEnabled | 1.3.6.1.4.1.17713.5.9.12 | INTEGER | read-write | This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) |
| INT hTTPPortNumber | 1.3.6.1.4.1.17713.5.9.14 | INTEGER | read-write | This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80) |
| INT hTTPSAccessEnabled | 1.3.6.1.4.1.17713.5.9.17 | INTEGER | read-write | This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) |
| INT hTTPSPortNumber | 1.3.6.1.4.1.17713.5.9.15 | INTEGER | read-write | This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443) |
| INT incompatibleMasterAndSlave | 1.3.6.1.4.1.17713.5.13.10 | INTEGER | read-only | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert |
| NTF incompatibleMasterAndSlaveTrap | 1.3.6.1.4.1.17713.5.99.0.20 | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert | ||
| INT incompatibleRegionCodes | 1.3.6.1.4.1.17713.5.13.4 | INTEGER | read-only | The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys |
| NTF incompatibleRegionCodesTrap | 1.3.6.1.4.1.17713.5.99.0.14 | The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys | ||
| INT installArmState | 1.3.6.1.4.1.17713.5.9.4 | INTEGER | read-only | Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert |
| NTF installArmStateTrap | 1.3.6.1.4.1.17713.5.99.0.10 | Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert | ||
| INT installStatus | 1.3.6.1.4.1.17713.5.9.3 | INTEGER | read-only | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert |
| NTF installStatusTrap | 1.3.6.1.4.1.17713.5.99.0.9 | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert | ||
| IP iPAddress | 1.3.6.1.4.1.17713.5.5.1 | IpAddress | read-write | Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute. |
| STR latitude | 1.3.6.1.4.1.17713.5.96.2 | DisplayString | read-write | The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| licence | 1.3.6.1.4.1.17713.5.8 | |||
| licenceGroup | 1.3.6.1.4.1.17713.5.98.8 | The licence object group. | ||
| INT licensedCapacity | 1.3.6.1.4.1.17713.5.8.11 | INTEGER | read-only | Maximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditions |
| INT linkLoss | 1.3.6.1.4.1.17713.5.12.5 | INTEGER | read-only | The wireless link loss expressed in tenths of a dB |
| INT linkModeOptimisation | 1.3.6.1.4.1.17713.5.10.2 | INTEGER | read-only | Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols. |
| INT linkModeOptimizationMismatch | 1.3.6.1.4.1.17713.5.13.14 | INTEGER | read-only | The remote node of this link has been configured with a different link mode optimization |
| NTF linkModeOptimizationMismatchTrap | 1.3.6.1.4.1.17713.5.99.0.25 | The remote node of this link has been configured with a different link mode optimization | ||
| STR linkName | 1.3.6.1.4.1.17713.5.5.14 | DisplayString | read-only | Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link. |
| INT linkSymmetry | 1.3.6.1.4.1.17713.5.10.1 | INTEGER | read-only | In fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amount of time transmitting and receiving. In fixed asymmetric mode (1 to 3) the receive time is three times as long as the transmit time. In adaptive mode the transmit and receive periods adjust with applied load. NB: only applicable for master nodes. |
| STR longitude | 1.3.6.1.4.1.17713.5.96.1 | DisplayString | read-write | The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| management | 1.3.6.1.4.1.17713.5.9 | |||
| managementGroup | 1.3.6.1.4.1.17713.5.98.9 | The management object group. | ||
| INT masterSlaveMode | 1.3.6.1.4.1.17713.5.5.5 | INTEGER | read-only | The PTP wireless link operates using a master and slave relationship |
| INT maximumTransmitPower | 1.3.6.1.4.1.17713.5.5.6 | INTEGER | read-only | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link |
| notificationsGroup | 1.3.6.1.4.1.17713.5.98.99 | The notifications group. | ||
| INT noWirelessChannelAvailable | 1.3.6.1.4.1.17713.5.13.5 | INTEGER | read-only | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| NTF noWirelessChannelAvailableTrap | 1.3.6.1.4.1.17713.5.99.0.15 | Spectrum Management was unable to locate a suitable wireless channel to operate on | ||
| phyControl | 1.3.6.1.4.1.17713.5.10 | |||
| phyControlGroup | 1.3.6.1.4.1.17713.5.98.10 | The phyControl object group. | ||
| phyStatus | 1.3.6.1.4.1.17713.5.12 | |||
| phyStatusGroup | 1.3.6.1.4.1.17713.5.98.12 | The phyStatus object group. | ||
| STR productName | 1.3.6.1.4.1.17713.5.8.3 | DisplayString | read-only | Name of the product variant |
| INT productVariant | 1.3.6.1.4.1.17713.5.8.2 | INTEGER | read-only | The product variant |
| ptmp | 1.3.6.1.4.1.17713.2 | |||
| ptp | 1.3.6.1.4.1.17713.1 | |||
| ptp500 | 1.3.6.1.4.1.17713.5 | |||
| ptpCompliance | 1.3.6.1.4.1.17713.5.97 | The compliance statement for the Cambium PTP MIB | ||
| ptpGroups | 1.3.6.1.4.1.17713.5.98 | |||
| ptpTrapPrefix | 1.3.6.1.4.1.17713.5.99.0 | |||
| ptpTraps | 1.3.6.1.4.1.17713.5.99 | |||
| pubStats | 1.3.6.1.4.1.17713.5.20 | |||
| pubStatsGroup | 1.3.6.1.4.1.17713.5.98.20 | The pubStats object group. | ||
| I32 range | 1.3.6.1.4.1.17713.5.12.4 | Integer32 | read-only | Distance between the two peer wireless units expressed in tenths of a kilometer |
| INT receiveChannel | 1.3.6.1.4.1.17713.5.12.6 | INTEGER | read-only | Current active receive channel |
| I32 receiveDataRate | 1.3.6.1.4.1.17713.5.20.1 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| INT receiveFreqKHz | 1.3.6.1.4.1.17713.5.12.14 | INTEGER | read-only | Current receive frequency expressed as KHz |
| INT receiveFreqMHz | 1.3.6.1.4.1.17713.5.12.11 | INTEGER | read-only | Current receive frequency expressed in integer MHz |
| INT receiveModulationMode | 1.3.6.1.4.1.17713.5.12.8 | INTEGER | read-only | Current active receive modulation mode |
| INT receiveModulationModeDetail | 1.3.6.1.4.1.17713.5.20.7 | INTEGER | read-only | The reason for the current receive modulation mode |
| I32 receivePower | 1.3.6.1.4.1.17713.5.12.1 | Integer32 | read-only | Receive power expressed in tenths of a dBm |
| INT regionCode | 1.3.6.1.4.1.17713.5.8.1 | INTEGER | read-only | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF regionCodeTrap | 1.3.6.1.4.1.17713.5.99.0.8 | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| IP remoteIPAddress | 1.3.6.1.4.1.17713.5.5.12 | IpAddress | read-only | IP Address of the peer wireless unit |
| INT remoteMaximumTransmitPower | 1.3.6.1.4.1.17713.5.10.4 | INTEGER | read-only | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| reset | 1.3.6.1.4.1.17713.5.18 | |||
| resetGroup | 1.3.6.1.4.1.17713.5.98.18 | The reset object group. | ||
| INT searchState | 1.3.6.1.4.1.17713.5.12.16 | INTEGER | read-only | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal. |
| STR secondarySoftwareVersion | 1.3.6.1.4.1.17713.5.19.3 | DisplayString | read-only | Secondary software version, used when the primary software image is invalid or erased |
| I32 signalStrengthRatio | 1.3.6.1.4.1.17713.5.12.13 | Integer32 | read-only | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB |
| STR siteName | 1.3.6.1.4.1.17713.5.5.15 | DisplayString | read-write | This field contains a user-provided description of the site name together with any additional notes |
| smtp | 1.3.6.1.4.1.17713.5.15 | |||
| STR sMTPDestinationEmailAddress | 1.3.6.1.4.1.17713.5.15.5 | DisplayString | read-write | The 'to' email address used when constructing the automatically generated e-mail message |
| INT sMTPEmailAlert | 1.3.6.1.4.1.17713.5.15.1 | INTEGER | read-write | Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system administrator |
| BIT sMTPEnabledMessages | 1.3.6.1.4.1.17713.5.15.6 | Bits | read-write | This controls which SMTP messages the unit will send |
| smtpGroup | 1.3.6.1.4.1.17713.5.98.15 | The smtp object group. | ||
| IP sMTPServerIPAddress | 1.3.6.1.4.1.17713.5.15.2 | IpAddress | read-write | IP address of the SMTP server |
| INT sMTPServerPortNumber | 1.3.6.1.4.1.17713.5.15.3 | INTEGER | read-write | Port number of the SMTP server |
| STR sMTPSourceEmailAddress | 1.3.6.1.4.1.17713.5.15.4 | DisplayString | read-write | The 'from' email address used when constructing the automatically generated e-mail message |
| STR sNMPCommunityString | 1.3.6.1.4.1.17713.5.16.2 | DisplayString | read-write | The SNMP community string. NB: A system reboot is required to activate changes to this attribute |
| snmpControl | 1.3.6.1.4.1.17713.5.16 | |||
| snmpControlGroup | 1.3.6.1.4.1.17713.5.98.16 | The snmpControl object group. | ||
| BIT sNMPEnabledTraps | 1.3.6.1.4.1.17713.5.16.6 | Bits | read-write | This controls which SNMP Traps the unit will send |
| INT sNMPPortNumber | 1.3.6.1.4.1.17713.5.16.1 | INTEGER | read-write | The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute |
| INT sNMPSendAllTrapsAtStartup | 1.3.6.1.4.1.17713.5.16.8 | INTEGER | read-write | Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up. |
| IP sNMPTrapIPAddress | 1.3.6.1.4.1.17713.5.16.4.1.2 | IpAddress | read-write | The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute. |
| INT sNMPTrapPortNumber | 1.3.6.1.4.1.17713.5.16.4.1.3 | INTEGER | read-write | Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute. |
| sNMPTrapTable | 1.3.6.1.4.1.17713.5.16.4 | not-accessible | SNMP trap configuration table. | |
| sNMPTrapTableEntry | 1.3.6.1.4.1.17713.5.16.4.1 | not-accessible | Table SNMPTrapTable | |
| INT sNMPTrapTableIndex | 1.3.6.1.4.1.17713.5.16.4.1.1 | INTEGER | not-accessible | SNMP trap value, used to index the SNMPTrapTable. |
| INT sNMPTrapTableNumber | 1.3.6.1.4.1.17713.5.16.3 | INTEGER | read-only | Number of entries in the sNMPTrapTable. |
| INT sNMPTrapVersion | 1.3.6.1.4.1.17713.5.16.5 | INTEGER | read-write | The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute |
| INT sNMPv3Enable | 1.3.6.1.4.1.17713.5.8.9 | INTEGER | read-only | SNMPv3 availability control |
| sntp | 1.3.6.1.4.1.17713.5.17 | |||
| sntpGroup | 1.3.6.1.4.1.17713.5.98.17 | The sntp object group. | ||
| I32 sNTPLastSync | 1.3.6.1.4.1.17713.5.17.6 | Integer32 | read-only | Last SNTP sync time |
| INT sNTPPollInterval | 1.3.6.1.4.1.17713.5.17.4 | INTEGER | read-write | The SNTP server polling interval |
| IP sNTPServerIPAddress | 1.3.6.1.4.1.17713.5.17.2 | IpAddress | read-write | The IP address of a valid SNTP server |
| INT sNTPServerPortNumber | 1.3.6.1.4.1.17713.5.17.3 | INTEGER | read-write | The IP port number of the SNTP server. Defaults to port 123. |
| INT sNTPState | 1.3.6.1.4.1.17713.5.17.1 | INTEGER | read-write | SNTP control state |
| INT sNTPSync | 1.3.6.1.4.1.17713.5.17.5 | INTEGER | read-only | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF sNTPSyncTrap | 1.3.6.1.4.1.17713.5.99.0.21 | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| STR softwareVersion | 1.3.6.1.4.1.17713.5.19.1 | DisplayString | read-only | Current software version |
| IP subnetMask | 1.3.6.1.4.1.17713.5.5.2 | IpAddress | read-write | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute |
| supplementary | 1.3.6.1.4.1.17713.5.96 | |||
| supplementaryGroup | 1.3.6.1.4.1.17713.5.98.96 | The supplementary object group. | ||
| INT syslogClient | 1.3.6.1.4.1.17713.5.24.1 | INTEGER | read-only | Enable or disable the syslog client |
| NTF syslogClientTrap | 1.3.6.1.4.1.17713.5.99.0.33 | Enable or disable the syslog client | ||
| syslogControl | 1.3.6.1.4.1.17713.5.24 | |||
| syslogControlGroup | 1.3.6.1.4.1.17713.5.98.24 | The syslogControl object group. | ||
| NTF syslogLocalNearlyFullTrap | 1.3.6.1.4.1.17713.5.99.0.31 | The syslog local log is nearly full (90%) | ||
| NTF syslogLocalWrappedTrap | 1.3.6.1.4.1.17713.5.99.0.32 | The syslog local log has wrapped | ||
| INT syslogState | 1.3.6.1.4.1.17713.5.24.2 | INTEGER | read-only | The syslog service has been enabled or disabled |
| NTF syslogStateTrap | 1.3.6.1.4.1.17713.5.99.0.30 | The syslog service has been enabled or disabled | ||
| I32 systemClock | 1.3.6.1.4.1.17713.5.17.7 | Integer32 | read-only | System clock presented as local time |
| INT systemReset | 1.3.6.1.4.1.17713.5.18.1 | INTEGER | read-write | Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory |
| OCT targetMACAddress | 1.3.6.1.4.1.17713.5.5.4 | OCTET STRING | read-only | MAC address of the PTP wireless unit forming the other end of the PTP link |
| tDDControl | 1.3.6.1.4.1.17713.5.23 | |||
| tDDControlGroup | 1.3.6.1.4.1.17713.5.98.23 | The tDDControl object group. | ||
| INT tDDSynchronizationAlarm | 1.3.6.1.4.1.17713.5.13.13 | INTEGER | read-only | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. |
| NTF tDDSynchronizationAlarmTrap | 1.3.6.1.4.1.17713.5.99.0.22 | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. | ||
| INT tDDSynchronizationMode | 1.3.6.1.4.1.17713.5.23.1 | INTEGER | read-only | TDD Synchronization Mode selection |
| INT tDDSynchronizationStatus | 1.3.6.1.4.1.17713.5.13.11 | INTEGER | read-only | An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference. |
| telecom | 1.3.6.1.4.1.17713.5.7 | |||
| telecomGroup | 1.3.6.1.4.1.17713.5.98.7 | The telecom object group. | ||
| INT telecomsCableLength | 1.3.6.1.4.1.17713.5.7.6 | INTEGER | read-only | The length of the cable connected to the telecoms interface, measured in feet |
| INT telecomsChannelStatus | 1.3.6.1.4.1.17713.5.7.2 | INTEGER | read-only | Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF telecomsChannelStatusTrap | 1.3.6.1.4.1.17713.5.99.0.4 | Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT telecomsInterface | 1.3.6.1.4.1.17713.5.7.1 | INTEGER | read-only | The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored. |
| INT telecomsLineCode | 1.3.6.1.4.1.17713.5.7.4 | INTEGER | read-only | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| INT telecomsLoopback | 1.3.6.1.4.1.17713.5.7.8 | INTEGER | read-only | The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| NTF telecomsLoopbackTrap | 1.3.6.1.4.1.17713.5.99.0.6 | The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert | ||
| INT telnetAccessEnabled | 1.3.6.1.4.1.17713.5.9.13 | INTEGER | read-write | This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled) |
| INT telnetPortNumber | 1.3.6.1.4.1.17713.5.9.16 | INTEGER | read-write | This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23) |
| IP tFTPServerIPAddress | 1.3.6.1.4.1.17713.5.9.5 | IpAddress | read-write | IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| INT tFTPServerPortNumber | 1.3.6.1.4.1.17713.5.9.6 | INTEGER | read-write | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| STR tFTPSoftwareUpgradeFileName | 1.3.6.1.4.1.17713.5.9.7 | DisplayString | read-write | Filename of the Software Upgrade to be loaded from the TFTP Server |
| INT tFTPSoftwareUpgradeStatus | 1.3.6.1.4.1.17713.5.9.9 | INTEGER | read-only | The current status of the TFTP Software upgrade process |
| STR tFTPSoftwareUpgradeStatusAdditionalText | 1.3.6.1.4.1.17713.5.9.11 | DisplayString | read-only | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| STR tFTPSoftwareUpgradeStatusText | 1.3.6.1.4.1.17713.5.9.10 | DisplayString | read-only | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| I32 tFTPStartSoftwareUpgrade | 1.3.6.1.4.1.17713.5.9.8 | Integer32 | read-write | Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished |
| INT timeZone | 1.3.6.1.4.1.17713.5.17.8 | INTEGER | read-write | Time zone offsets from Greenwich Mean Time (GMT) |
| INT transmitChannel | 1.3.6.1.4.1.17713.5.12.7 | INTEGER | read-only | Current active transmit channel |
| I32 transmitDataRate | 1.3.6.1.4.1.17713.5.20.2 | Integer32 | read-only | Average data rate over the last one second interval (kbps) |
| INT transmitFreqKHz | 1.3.6.1.4.1.17713.5.12.15 | INTEGER | read-only | Current transmit frequency expressed as KHz |
| INT transmitFreqMHz | 1.3.6.1.4.1.17713.5.12.12 | INTEGER | read-only | Current transmit frequency expressed in integer MHz |
| INT transmitModulationMode | 1.3.6.1.4.1.17713.5.12.9 | INTEGER | read-only | Current active transmit modulation mode |
| I32 transmitPower | 1.3.6.1.4.1.17713.5.12.3 | Integer32 | read-only | Transmit power expressed in tenths of a dBm |
| INT unitOutOfCalibration | 1.3.6.1.4.1.17713.5.13.1 | INTEGER | read-only | The unit is out of calibration |
| NTF unitOutOfCalibrationTrap | 1.3.6.1.4.1.17713.5.99.0.11 | The unit is out of calibration | ||
| INT userConfiguredMaxModulationMode | 1.3.6.1.4.1.17713.5.10.3 | INTEGER | read-write | The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard |
| INT userEnabled | 1.3.6.1.4.1.17713.5.25.2.1.4 | INTEGER | read-only | Enable / Disable the selected user |
| OCT userName | 1.3.6.1.4.1.17713.5.25.2.1.2 | OCTET STRING | read-only | User name which must be entered, along with the appropriate password, in order to gain access to the system. |
| OCT userPassword | 1.3.6.1.4.1.17713.5.25.2.1.5 | OCTET STRING | read-write | User password, which must be entered in order to gain access to the system. |
| INT userRole | 1.3.6.1.4.1.17713.5.25.2.1.3 | INTEGER | read-only | Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes. |
| userTable | 1.3.6.1.4.1.17713.5.25.2 | not-accessible | The User Table Control group contains objects specifically for user account management. | |
| userTableEntry | 1.3.6.1.4.1.17713.5.25.2.1 | not-accessible | Table UserTable | |
| INT userTableIndex | 1.3.6.1.4.1.17713.5.25.2.1.1 | INTEGER | not-accessible | used to index values in the userTable. |
| INT userTableNumber | 1.3.6.1.4.1.17713.5.25.1 | INTEGER | read-only | Number of entries in the userTable |
| INT useVLANForManagementInterfaces | 1.3.6.1.4.1.17713.5.6.7 | INTEGER | read-write | This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot |
| I32 vectorError | 1.3.6.1.4.1.17713.5.12.2 | Integer32 | read-only | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB |
| versions | 1.3.6.1.4.1.17713.5.19 | |||
| versionsGroup | 1.3.6.1.4.1.17713.5.98.19 | The versions object group. | ||
| INT vLANManagementPriority | 1.3.6.1.4.1.17713.5.6.8 | INTEGER | read-write | This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| INT vLANManagementVID | 1.3.6.1.4.1.17713.5.6.11 | INTEGER | read-write | This VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| INT vLANPriorityQueueMapping | 1.3.6.1.4.1.17713.5.6.15.1.1 | INTEGER | read-write | Mapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority. |
| vLANPriorityTable | 1.3.6.1.4.1.17713.5.6.15 | not-accessible | A priority queue mapping table. This is a list of packet queues indexed by VLAN priority. | |
| vLANPriorityTableEntry | 1.3.6.1.4.1.17713.5.6.15.1 | not-accessible | Table VLANPriorityTable | |
| INT vLANPriorityTableIndex | 1.3.6.1.4.1.17713.5.6.15.1.2 | INTEGER | not-accessible | VLAN priority flag, used to index values in the vLANPriorityTable. |
| INT vLANPriorityTableNumber | 1.3.6.1.4.1.17713.5.6.14 | INTEGER | read-only | Number of entries in the vLANPriorityTable. |
| INT wirelessLinkAvailability | 1.3.6.1.4.1.17713.5.20.4 | INTEGER | read-only | Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| INT wirelessLinkDisabledWarning | 1.3.6.1.4.1.17713.5.13.6 | INTEGER | read-only | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic |
| NTF wirelessLinkDisabledWarningTrap | 1.3.6.1.4.1.17713.5.99.0.16 | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic | ||
| INT wirelessLinkStatus | 1.3.6.1.4.1.17713.5.20.5 | INTEGER | read-only | Current status of the wireless link |
RFC description
Management of Cambium PTP500 non-line-of-sight wireless ethernet bridge links.
Start monitoring Cambium Networks PTP-series wireless Ethernet bridge with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.