All MIBs › BREEZECOM-MIB
Category: Vendor: Alvarion, Wireless and WLAN
Description: Manages BreezeCOM (Alvarion/Breezecom) wireless bridge radio link configuration and performance statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is BREEZECOM-MIB?
This is a BreezeCOM (later Alvarion) private MIB for managing wireless bridge and access point radio links, covering system-level control and RF performance monitoring. It exposes a mix of configuration/command objects (system reset, reset counters, set/restore defaults) and RF performance data such as carrier sense counters and noise floor readings. This module explicitly supports monitoring hardware status: sysNoiseFloor and sysCarrierSense/sysDeltaCarrierSense reveal RF link quality and interference conditions, while sysExternalAmplifier and sysRunFromNonActiveCode indicate hardware/firmware configuration state such as whether the unit booted from a backup firmware image. As an early wireless vendor-private MIB it doesn't reference external standard MIBs directly, relying on its own "brzSys" object tree for system control. It is typically deployed in fixed-wireless/point-to-point bridge links using BreezeCOM/Alvarion radio equipment in outdoor or industrial settings. Engineers can download the BREEZECOM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in BREEZECOM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- BreezeCOM/Alvarion wireless bridge
- fixed wireless point-to-point radio
Monitoring Examples
An administrator monitors sysNoiseFloor and sysCarrierSense/sysDeltaCarrierSense to detect rising RF interference affecting a wireless bridge link, and checks sysRunFromNonActiveCode to confirm whether the unit is running its primary or backup firmware image after a reset. A high or rapidly increasing sysDeltaCarrierSense combined with a degraded link would point to RF interference or antenna/alignment problems, while a climbing sysTrapCounter indicates a flood of device traps needing investigation.
What Can Be Monitored
- RF noise floor
- carrier sense count/delta
- external amplifier presence
- active firmware image (primary/backup)
- trap counter
This MIB depends on
Related MIBs
Imported Objects
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| accessRights | 1.3.6.1.4.1.710.3.2.1.1.10 | |||
| adbEntry | 1.3.6.1.4.1.710.3.2.3.2.2.1.1 | not-accessible | An entry in ADB table. | |
| adbTable | 1.3.6.1.4.1.710.3.2.3.2.2.1 | not-accessible | A table of the stations associated. | |
| CTR assocRequestRecive | 1.3.6.1.4.1.710.3.2.4.4.1.8 | Counter | read-only | For an AP: Number of Association request frames that has received. |
| CTR assocRequestSent | 1.3.6.1.4.1.710.3.2.4.4.2.6 | Counter | read-only | For WB or SA: Number of Association request frames that sent. |
| CTR assocRequestSentRetx | 1.3.6.1.4.1.710.3.2.4.4.2.7 | Counter | read-only | For WB or SA: Number of Retransmitted Association request frames that sent. |
| CTR assocResponceRecive | 1.3.6.1.4.1.710.3.2.4.4.2.8 | Counter | read-only | For WB or SA: Number of received Association response frames. |
| CTR assocResponseLost | 1.3.6.1.4.1.710.3.2.4.4.1.6 | Counter | read-only | For an AP: Number of Association response frames that got lost. |
| CTR assocResponseSent | 1.3.6.1.4.1.710.3.2.4.4.1.5 | Counter | read-only | For an AP: Number of Association response frames that sent. |
| CTR assocResponseSentRetx | 1.3.6.1.4.1.710.3.2.4.4.1.7 | Counter | read-only | For an AP: Number of retransmitted Association response frames that sent. |
| CTR authRequestSent | 1.3.6.1.4.1.710.3.2.4.4.2.3 | Counter | read-only | For WB or SA: Number of Authentication request frames that sent. |
| CTR authRequestSentRetx | 1.3.6.1.4.1.710.3.2.4.4.2.4 | Counter | read-only | For WB or SA: Number of Retransmitted Authentication request frames that sent. |
| CTR authResponceRecive | 1.3.6.1.4.1.710.3.2.4.4.2.5 | Counter | read-only | For WB or SA: Number of received Authentication response frames. |
| breezecom | 1.3.6.1.4.1.710 | |||
| breezecomAP10 | 1.3.6.1.4.1.710.4.1 | |||
| breezecomOID | 1.3.6.1.4.1.710.4 | |||
| breezecomPrvRev | 1.3.6.1.4.1.710.3 | |||
| breezecomSA10 | 1.3.6.1.4.1.710.4.3 | |||
| breezecomSA40 | 1.3.6.1.4.1.710.4.4 | |||
| breezecomWB10 | 1.3.6.1.4.1.710.4.2 | |||
| INT brzACKDelayed | 1.3.6.1.4.1.710.3.2.1.2.16 | INTEGER | read-write | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network. |
| brzAP | 1.3.6.1.4.1.710.3.2.3.2 | |||
| NTF brzAPaging | 1.3.6.1.4.1.710.4.1.0.4 | An AP trap indicating that the station association was aged out, and removed from that AP. The trap contains the MAC address of the aging station | ||
| NTF brzAPassociated | 1.3.6.1.4.1.710.4.1.0.2 | An AP trap indicating that a new station was associated with this AP. It contains the MAC address of the associated station. | ||
| NTF brzAPdisassociated | 1.3.6.1.4.1.710.4.1.0.3 | An AP trap indicating that the station dis-associated itself from the AP. The trap contains the MAC address of the disassociated station. | ||
| INT brzApplTunneling | 1.3.6.1.4.1.710.3.2.1.2.2 | INTEGER | read-write | This attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-talk - The device will enable AppleTalk tunneling only. none - The device will disable tunneling. both - The device will enable only IPX and AppleTalk tunneling. |
| INT brzApRedundancyLimit | 1.3.6.1.4.1.710.3.2.1.2.13 | INTEGER | read-write | This attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast frames for the cell arrive from the Ethernet. This option is available ONLY on AP (na value assigned in non-AP devices). |
| INT brzApRedundancySupport | 1.3.6.1.4.1.710.3.2.1.2.10 | INTEGER | read-write | Setting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no multicast or unicast frames for the cell arrive from the Ethernet during a period of 100 seconds. This option is available ONLY on AP (na value assigned in non-AP devices). |
| NTF brzAProamedOut | 1.3.6.1.4.1.710.4.1.0.5 | An AP trap indicating that a given station has roamed out from this AP. The trap contains the MAC address of the roamed out station | ||
| NTF brzAProamingIn | 1.3.6.1.4.1.710.4.1.0.1 | A trap indicating that a station has roamed into this AP. It contains the MAC address of the associated station and the device type of that station. | ||
| NTF brzAPWlanStatusap | 1.3.6.1.4.1.710.4.1.0.7 | An AP trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. | ||
| INT brzAuthenticationType | 1.3.6.1.4.1.710.3.2.1.2.8 | INTEGER | read-only | This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one of the following: 1 - Open System, 2 - Shared Key, 20 - Special Authentication Algorithm (#0), 21 - Special Authentication Algorithm (#1), 22 - Special Authentication Algorithm (#2). |
| STR brzAvrgDBm | 1.3.6.1.4.1.710.3.2.3.1.11 | DisplayString | read-only | A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of -255). |
| INT brzAvrgRssi | 1.3.6.1.4.1.710.3.2.3.1.3 | INTEGER | read-only | A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of 255). |
| INT brzBadBeacons | 1.3.6.1.4.1.710.3.2.3.1.9 | INTEGER | read-only | A value representing the number of beacons received with Strength less then join level from that AP. |
| INT brzBeaconInterval | 1.3.6.1.4.1.710.3.2.1.2.19 | INTEGER | read-write | This attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's. |
| INT brzCFMode | 1.3.6.1.4.1.710.3.2.3.3.5 | INTEGER | read-only | This attribute is set to ON if the station required Contention Free services from the AP (hence it is in the AP's Contention Free list). This option is available ONLY on stations. A Not Applicable value is returned for all APs. |
| brzCnt | 1.3.6.1.4.1.710.3.2.4 | |||
| MAC brzCurrentAPMacAddress | 1.3.6.1.4.1.710.3.2.3.3.1 | MacAddress | read-only | Hardware MAC address of the AP currently associated with. Available ONLY in station. |
| CTR brzDiscarded | 1.3.6.1.4.1.710.3.2.4.2.1.3 | Counter | read-only | This attribute counts the number of data frames, that were internally discarded in the system, instead of being transmitted over the Wireless LAN. High values of this counter indicate either very high traffic volume, or a noisy environment that prevents Wireless transmissions. |
| STR brzDisplayNonActiveCodeVersion | 1.3.6.1.4.1.710.3.2.1.2.27 | DisplayString | read-only | This attribute displays the active code version and the non active code version. |
| brzdot11 | 1.3.6.1.4.1.710.3.2.6 | |||
| brzDSCnt | 1.3.6.1.4.1.710.3.2.4.1 | |||
| INT brzDTIMPperiod | 1.3.6.1.4.1.710.3.2.1.2.17 | INTEGER | read-write | This attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in AP's. |
| INT brzEnableVoice | 1.3.6.1.4.1.710.3.2.1.2.22 | INTEGER | read-write | This attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's. |
| CTR brzFailedCountOnWlan | 1.3.6.1.4.1.710.3.2.4.2.1.6 | Counter | read-only | This attribute counts the number of frames that were dropped (not transmitted), due to the number of retransmits attempts exceeding the RetryMax value. |
| NTF brzGeneralAP | 1.3.6.1.4.1.710.4.1.0.9 | An AP general purpose trap, for future trap implementation. | ||
| NTF brzGeneralSA40 | 1.3.6.1.4.1.710.4.4.0.9 | SA-40 general purpose trap, for future trap implementation. | ||
| NTF brzGeneralSTA | 1.3.6.1.4.1.710.4.3.0.9 | A STA general purpose trap, for future trap implementation. | ||
| NTF brzGeneralWB | 1.3.6.1.4.1.710.4.2.0.9 | A WB general purpose trap, for future trap implementation. | ||
| MAC brzHWMacAddress | 1.3.6.1.4.1.710.3.2.1.2.1 | MacAddress | read-only | The Hardware MAC address of the device. |
| INT brzIntelligentBridgingPeriod | 1.3.6.1.4.1.710.3.2.1.2.28 | INTEGER | read-write | This attribute defines the Intelligent Bridging Period in seconds. |
| INT brzIpFilter | 1.3.6.1.4.1.710.3.2.1.2.4 | INTEGER | read-write | Setting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be used on environments where only IP (and ARP) traffic is permitted. |
| INT brzIPStack | 1.3.6.1.4.1.710.3.2.2.7 | INTEGER | read-write | This attribute defines whether to use IP stack or not. |
| INT brzJoinDecisionRSSIThreshold | 1.3.6.1.4.1.710.3.2.3.4.4 | INTEGER | read-write | A station will join a new AP only if the AP transmits with an RSSI quality above the value which is defined by this parameter. Available ONLY in stations. In AP's, this is the threshold for sending Bad WLAN Conditions traps. If a station associated with the AP is heard at an RSII level below this threshold, a Bad WLAN Conditions trap is sent by the AP. |
| MAC brzLastAPMacAddress | 1.3.6.1.4.1.710.3.2.3.3.2 | MacAddress | read-only | The Hardware MAC address of the last AP that the station was associated with. Available ONLY in stations. |
| INT brzLastBeacon | 1.3.6.1.4.1.710.3.2.3.1.8 | INTEGER | read-only | A value representing last dwell to receive beacon from that AP. |
| INT brzLoadStations | 1.3.6.1.4.1.710.3.2.3.1.10 | INTEGER | read-only | A value representing the number of stations associated to that AP. |
| INT brzMaxNumberOfScanning | 1.3.6.1.4.1.710.3.2.3.4.8 | INTEGER | read-write | This parameter defines a maximum number of scanning Attempts to perform before system reset. Zero is value for non reset. Available ONLY in stations. |
| INT brzMaxRate | 1.3.6.1.4.1.710.3.2.3.1.1 | INTEGER | read-write | This attribute indicates the rate (in Mbits per second) at which data will be transmitted across the medium. The default value of this attribute shall be 3. |
| CTR brzMissedFrames | 1.3.6.1.4.1.710.3.2.4.1.5 | Counter | read-only | This attribute counts the total number of missed frames that have missed the transmission to the Ethernet LAN. |
| brzMngAP | 1.3.6.1.4.1.710.3.2.4.4.1 | |||
| brzMngCnt | 1.3.6.1.4.1.710.3.2.4.4 | |||
| brzMngSAWB | 1.3.6.1.4.1.710.3.2.4.4.2 | |||
| INT brzMobilLvl | 1.3.6.1.4.1.710.3.2.3.1.2 | INTEGER | read-write | This attribute indicates the expected mobility level of the system. The default value of this attribute is stationary. |
| INT brzNeighboringBeaconRate | 1.3.6.1.4.1.710.3.2.3.4.9 | INTEGER | read-write | This parameter defines the Neighboring Beacon Rate in dwells. Zero is value for non Neighboring Beacons. Available ONLY in AP's. |
| INT brzNeighboringBeacons | 1.3.6.1.4.1.710.3.2.3.4.5 | INTEGER | read-write | This parameters defines once in how many dwell times the AP will send a neighboring beacon. Available ONLY in AP's. |
| brznetmib | 1.3.6.1.4.1.710.3.2 | |||
| STR brzNonActiveCodeState | 1.3.6.1.4.1.710.3.2.1.2.26 | DisplayString | read-only | This attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in station throughput, also answer is delayed!!! |
| INT brzNumberOfBeaconsForDisconnect | 1.3.6.1.4.1.710.3.2.3.4.7 | INTEGER | read-write | This parameter defines a maximum number of consecutive not arrived Beacons that is allowed before a disconnect decision. Available ONLY in stations. |
| INT brzNumberOfProbeResponses | 1.3.6.1.4.1.710.3.2.3.4.6 | INTEGER | read-write | If a number of good RSSI samples coming from a neighbor is greater than or equal to this parameter the neighbor might be selected for joining. |
| CTR brzNumOfReassocRequests | 1.3.6.1.4.1.710.3.2.4.3.1 | Counter | read-only | For an AP: The number of Associations and ReAssociations requests, received since the last reset of the AP. This counter is useful for getting information about mobility activity on the BSS. For a Station: The number of Associations and ReAssociation requests issued by the station since the last reset. |
| INT brzPositiveBrg | 1.3.6.1.4.1.710.3.2.1.2.3 | INTEGER | read-write | This attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the Wireless LAN only frames that are destined to associated stations. forward-unknown - The AP forwards to the Wireless LAN frames destined to associated AND unknown addresses. This value should be used only for Wireless Bridge installations. intelligent - If connected to a wireless bridge, the AP automatically activates the Forward-Unknown option. na - A not applicable value, for non-AP devices. |
| INT brzPowerMngBitTestMode | 1.3.6.1.4.1.710.3.2.1.2.18 | INTEGER | read-write | This attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode of operation), and ENABLED. |
| INT brzPowerMngMode | 1.3.6.1.4.1.710.3.2.1.2.15 | INTEGER | read-write | This attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of operation), and POWER SAVE. An STA will always return an ACTIVE value. |
| INT brzPowerSaveSupport | 1.3.6.1.4.1.710.3.2.1.2.20 | INTEGER | read-write | This attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Save support with PM bit test This attribute is applicable only in AP's. |
| MAC brzPreferredAPMacAddress | 1.3.6.1.4.1.710.3.2.3.3.3 | MacAddress | read-write | The Hardware MAC address of the preferred AP, to which the station should associate when ever possible. Null value here indicates no preferences. Available ONLY in stations. |
| brzPSCnt | 1.3.6.1.4.1.710.3.2.4.5 | |||
| CTR brzRetryOnWlan | 1.3.6.1.4.1.710.3.2.4.2.1.5 | Counter | read-only | This attribute counts the total number of retransmitted fragments, on the Wireless LAN. |
| CTR brzRetryOnWlanPercent | 1.3.6.1.4.1.710.3.2.4.2.1.7 | Counter | read-only | This attribute calculates the percentage of number frames (to the data and management) that have been transmitted successfully Wireless LAN. |
| CTR brzRetryTxDataToWlan | 1.3.6.1.4.1.710.3.2.4.2.1.8 | Counter | read-only | This attribute counts the total number of data frames that have been retransmitted to the Wireless LAN. |
| CTR brzRetryTxDataToWlanPercent | 1.3.6.1.4.1.710.3.2.4.2.1.9 | Counter | read-only | This attribute calculates the percentage of data frames that have been transmitted successfully to the Wireless LAN. |
| brzRoamCnt | 1.3.6.1.4.1.710.3.2.4.3 | |||
| INT brzRoamDecisionNumerator | 1.3.6.1.4.1.710.3.2.3.4.2 | INTEGER | read-write | This parameter defines a maximum number of RSSI samples that is allowed to be below brzRoamDecisionRSSIThreshold, among a number equal to brzRoamDecisionWin of the last arrived samples. If a number of bad samples (i.e. below brzRoamDecisionRSSIThreshold) exceeds one, which is defined by this parameter, the channel is considered as bad. Available ONLY in stations. |
| INT brzRoamDecisionRSSIThreshold | 1.3.6.1.4.1.710.3.2.3.4.3 | INTEGER | read-write | If an RSSI sample is bellow the value which is defined by this parameter the sample is considered as bad. Available ONLY in stations. |
| INT brzRoamDecisionWin | 1.3.6.1.4.1.710.3.2.3.4.1 | INTEGER | read-write | This parameter defines a minimum number of RSSI samples which is required to make a decision about the current WLAN channel quality. A new RSSI sample arrives with each incoming frame. Available ONLY in stations. |
| brzRoamParams | 1.3.6.1.4.1.710.3.2.3.4 | |||
| MAC brzRoamToAPMacAddress | 1.3.6.1.4.1.710.3.2.3.3.4 | MacAddress | read-write | Setting this attribute to a specific AP MAC address, will cause the station to roam immediately to that AP, if possible. Available ONLY for stations. |
| CTR brzRxBadFragFromWlan | 1.3.6.1.4.1.710.3.2.4.2.2.4 | Counter | read-only | This counter is incremented when an error is detected in a fragment, received from the Wireless LAN. |
| CTR brzRxBadFromDS | 1.3.6.1.4.1.710.3.2.4.1.2 | Counter | read-only | This attribute counts the number errored frames, received from the Wired Distribution system. |
| CTR brzRxDuplicateFragFromWlan | 1.3.6.1.4.1.710.3.2.4.2.2.5 | Counter | read-only | This counter is incremented when a duplicated fragment is received from the Wireless LAN. |
| CTR brzRxForwardToWlan | 1.3.6.1.4.1.710.3.2.4.1.8 | Counter | read-only | This attribute counts the total number of packets that have been transmitted successfully to the Wireless LAN. |
| CTR brzRxFragFromWlan | 1.3.6.1.4.1.710.3.2.4.2.2.3 | Counter | read-only | This attribute counts the number of fragments (data and management), that have been received successfully from the Wireless LAN. |
| CTR brzRxFromDS | 1.3.6.1.4.1.710.3.2.4.1.1 | Counter | read-only | This attribute counts the total number of frames that have been received successfully from the Wired Distribution system. |
| CTR brzRxMSDUFromWlan | 1.3.6.1.4.1.710.3.2.4.2.2.2 | Counter | read-only | This attribute counts the total number of MSDUs (data frames) that have been received successfully from the Wireless LAN. |
| CTR brzRxOctetsForwardToWlan | 1.3.6.1.4.1.710.3.2.4.1.7 | Counter | read-only | This attribute counts the total number of octets that have been transmitted successfully to the Wireless LAN. |
| CTR brzRxOctetsFromDS | 1.3.6.1.4.1.710.3.2.4.1.3 | Counter | read-only | This attribute counts the total number of octets that have been received successfully from the Wired Distribution system. |
| CTR brzRxPacketsFromWlan | 1.3.6.1.4.1.710.3.2.4.2.2.1 | Counter | read-only | This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN. |
| brzRxWlanCnt | 1.3.6.1.4.1.710.3.2.4.2.2 | |||
| NTF brzSA40associated | 1.3.6.1.4.1.710.4.4.0.6 | A SA-40 trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). | ||
| NTF brzSA40WlanStatus | 1.3.6.1.4.1.710.4.4.0.7 | SA-40 trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. | ||
| brzSTA | 1.3.6.1.4.1.710.3.2.3.3 | |||
| NTF brzSTAassociated | 1.3.6.1.4.1.710.4.3.0.6 | A station trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). | ||
| INT brzStaNumForLargeCW | 1.3.6.1.4.1.710.3.2.1.2.14 | INTEGER | read-write | This attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will use the default CW. (The value is in the range of 1-120) |
| NTF brzSTAWlanStatus | 1.3.6.1.4.1.710.4.3.0.7 | A STA trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. | ||
| brzSys | 1.3.6.1.4.1.710.3.2.1 | |||
| MAC brzTotalRetx | 1.3.6.1.4.1.710.3.2.3.3.9 | MacAddress | read-only | Total Retransmitted frames including all rates. |
| CTR brzTotalTxPacketsToWlan | 1.3.6.1.4.1.710.3.2.4.2.1.10 | Counter | read-only | This attribute counts the total number frames (data and management) that have been transmitted to the Wireless LAN. |
| INT brzTranslationMode | 1.3.6.1.4.1.710.3.2.1.2.5 | INTEGER | read-write | When this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunneling of data frames apply. All devices within the same Wireless LAN network, must have the same Translation Mode assigned. |
| MAC brzTrapAPMacAddr | 1.3.6.1.4.1.710.3.2.5.1 | MacAddress | read-only | The MAC address of an AP |
| INT brzTrapIndex | 1.3.6.1.4.1.710.3.2.5.6 | INTEGER | read-only | Index number for future trap implementation |
| INT brzTrapLastRssiQuality | 1.3.6.1.4.1.710.3.2.5.5 | INTEGER | read-only | The RSSI level of the signal received from the previous Access Point |
| MAC brzTrapMacAddress | 1.3.6.1.4.1.710.3.2.5.3 | MacAddress | read-only | A STA or AP MAC address |
| INT brzTrapRssiQuality | 1.3.6.1.4.1.710.3.2.5.4 | INTEGER | read-only | The RSSI level of the signal received from the Access Point |
| brzTraps | 1.3.6.1.4.1.710.3.2.5 | |||
| MAC brzTrapSTAMacAddr | 1.3.6.1.4.1.710.3.2.5.2 | MacAddress | read-only | The MAC address of a station device |
| INT brzTrapSTAType | 1.3.6.1.4.1.710.3.2.5.9 | INTEGER | read-only | This attribute identifies the device type of the station. |
| STR brzTrapText | 1.3.6.1.4.1.710.3.2.5.7 | DisplayString | read-only | Textual string for future trap implementation |
| INT brzTrapToggle | 1.3.6.1.4.1.710.3.2.5.8 | INTEGER | read-only | A general ON/OFF toggle value, for the traps. |
| CTR brzTx1MBitRate | 1.3.6.1.4.1.710.3.2.3.3.6 | Counter | read-only | Total transmitted frames in 1 MBit rate. |
| CTR brzTx2MBitRate | 1.3.6.1.4.1.710.3.2.3.3.7 | Counter | read-only | Total transmitted frames in 2 MBit rate. |
| CTR brzTx3MBitRate | 1.3.6.1.4.1.710.3.2.3.3.8 | Counter | read-only | Total transmitted frames in 3 MBit rate. |
| CTR brzTxErrorAbort | 1.3.6.1.4.1.710.3.2.4.2.1.15.5 | Counter | read-only | This attribute counts the total number of errors caused by frame abortion from Boori. |
| CTR brzTxErrorAckCRC | 1.3.6.1.4.1.710.3.2.4.2.1.15.2 | Counter | read-only | This attribute counts the total number of acknowledge CRC Errors on the Wireless LAN. |
| CTR brzTxErrorAckTimeOut | 1.3.6.1.4.1.710.3.2.4.2.1.15.1 | Counter | read-only | This attribute counts the total number of acknowledge timeouts on the Wireless LAN. |
| CTR brzTxErrorFrameReceived | 1.3.6.1.4.1.710.3.2.4.2.1.15.6 | Counter | read-only | This attribute counts the total number of errors caused by frame failure on the Wireless LAN. |
| CTR brzTxErrorNoTimeUntilHop | 1.3.6.1.4.1.710.3.2.4.2.1.15.3 | Counter | read-only | This attribute counts the total number of timeouts caused of on time until end of hop on the Wireless Cell. |
| CTR brzTxErrorUnderRunAndCTS | 1.3.6.1.4.1.710.3.2.4.2.1.15.4 | Counter | read-only | This attribute counts the total number of errors caused by HW problems (Under Run). |
| brzTxErrTransmitions | 1.3.6.1.4.1.710.3.2.4.2.1.15 | |||
| CTR brzTxFragToWlan | 1.3.6.1.4.1.710.3.2.4.2.1.4 | Counter | read-only | This attribute counts the total number of fragments (data and management) that have been transmitted to the Wireless LAN. |
| CTR brzTxMSDUToWlan | 1.3.6.1.4.1.710.3.2.4.2.1.2 | Counter | read-only | This attribute counts the total number of frames (data frames) that have been transmitted to the Wireless LAN. |
| CTR brzTxOctetsToDS | 1.3.6.1.4.1.710.3.2.4.1.6 | Counter | read-only | This attribute counts the total number of octets that have been transmitted successfully to the Wired Distribution system. |
| CTR brzTxPacketsToWlan | 1.3.6.1.4.1.710.3.2.4.2.1.1 | Counter | read-only | This attribute counts the total number of frames (data and management) that have been transmitted to the Wireless LAN. |
| CTR brzTxToDS | 1.3.6.1.4.1.710.3.2.4.1.4 | Counter | read-only | This attribute counts the total number of frames that have been transmitted to the Wired Distribution system. |
| brzTxWlanCnt | 1.3.6.1.4.1.710.3.2.4.2.1 | |||
| NTF brzWBassociated | 1.3.6.1.4.1.710.4.2.0.6 | A WB trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). | ||
| NTF brzWBWlanStatus | 1.3.6.1.4.1.710.4.2.0.7 | A WB trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. | ||
| INT brzWIXSupport | 1.3.6.1.4.1.710.3.2.1.2.6 | INTEGER | read-write | This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network. |
| brzWlan | 1.3.6.1.4.1.710.3.2.3 | |||
| INT brzWlanAssocAge | 1.3.6.1.4.1.710.3.2.1.2.21 | INTEGER | read-write | This attribute defines the Association Aging Period. |
| brzWlanCnt | 1.3.6.1.4.1.710.3.2.4.2 | |||
| STR brzWlanNetID | 1.3.6.1.4.1.710.3.2.1.2.7 | DisplayString | read-write | This attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs. |
| brzWlanParams | 1.3.6.1.4.1.710.3.2.3.1 | |||
| INT brzWlanProtocol | 1.3.6.1.4.1.710.3.2.3.1.4 | INTEGER | read-write | This attribute specifies the MAC/PHY protocol, utilized by this system. This attribute is not write accessible for regular users. |
| INT brzWlanQuality | 1.3.6.1.4.1.710.3.2.3.1.6 | INTEGER | read-only | A measure for quality (and noise level) of the Wireless LAN. |
| INT brzWlanRelayBroadcast | 1.3.6.1.4.1.710.3.2.1.2.12 | INTEGER | read-write | This attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broadcast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's. |
| INT brzWlanRelayUnicast | 1.3.6.1.4.1.710.3.2.1.2.11 | INTEGER | read-write | This attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's. |
| STR brzWlanRTNetID | 1.3.6.1.4.1.710.3.2.1.2.9 | DisplayString | read-only | This attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs. |
| NTF brzWlanStatusOfStation | 1.3.6.1.4.1.710.4.1.0.8 | An AP trap, indicating a change in the quality of the Wireless connection, with a specific (associated) station. An ON value indicates a specially bad connection, and an OFF value is sent if the quality improves, exceeding a predetermined threshold value. The brzTrapMacAddress contains the MAC address of the applicable station. | ||
| INT brzWlanTrapThreashold | 1.3.6.1.4.1.710.3.2.3.1.5 | INTEGER | read-write | This attribute specifies a threshold value, for sending the WlanStatusTRAP. When the Wireless LAN quality drops below (or goes above) this value, a trap will be issued. |
| bssApAdb | 1.3.6.1.4.1.710.3.2.3.2.2 | |||
| INT bssCollectPerStationInfo | 1.3.6.1.4.1.710.3.2.3.2.1.3 | INTEGER | read-write | When this attribute is set to ON, the AP accumulates Wireless Link statistics per each station. This option is available only for the AP. At stations it is always assigned with na (Not Applicable) value. WARNING: Setting this attribute to ON can cause substantial degradation in cell throughput!!! |
| bssInfo | 1.3.6.1.4.1.710.3.2.3.2.1 | |||
| INT bssNumOfBeaconLost | 1.3.6.1.4.1.710.3.2.3.2.1.5 | INTEGER | read-only | This attribute contains the total beacons lost counter. |
| INT bssNumOfBeaconSent | 1.3.6.1.4.1.710.3.2.3.2.1.4 | INTEGER | read-only | This attribute contains the total beacons sent counter. |
| INT bssNumOfStations | 1.3.6.1.4.1.710.3.2.3.2.1.1 | INTEGER | read-only | This attribute specifies the number of devices, that are currently associated with this AP. |
| INT bssNumOfStationsAuthenticated | 1.3.6.1.4.1.710.3.2.3.2.1.6 | INTEGER | read-only | This attribute specifies the number of devices, that are currently Authenticated with this AP. |
| INT bssNumOfStationsAuthenticatedPeak | 1.3.6.1.4.1.710.3.2.3.2.1.7 | INTEGER | read-only | This attribute contains the maximum value that bssNumOfStationsAuthenticated has reached. |
| INT bssNumOfStationsPeak | 1.3.6.1.4.1.710.3.2.3.2.1.2 | INTEGER | read-only | This attribute contains the maximum value that bssNumOfStations has reached. |
| INT dot11CurrentDwellTime | 1.3.6.1.4.1.710.3.2.6.4.5.5 | INTEGER | read-write | This attribute specifies the current time, in Kilo-microseconds, that the radio operates on a single channel. The value is from 19 - 390. The same Dwell Time value should be assigned to all the devices within the same Wireless LAN network. |
| INT dot11CurrentPattern | 1.3.6.1.4.1.710.3.2.6.4.5.7 | INTEGER | read-write | This attribute represents the current pattern that the device is using to determine the hop sequence. |
| INT dot11CurrentRegDomain | 1.3.6.1.4.1.710.3.2.6.4.1.3 | INTEGER | read-write | This attribute specifies the regularity domain, for the radio operation of this device. This integer contains an 8 bit value, as defined below: 00h - EthAirNet, 10h - USA, 20h - Canada, 30h - Europe, 31h - Spain, 32h - France, 37h - Europe Double Deviation, 38h - Netherlands, 40h - Japan, 41h - Korea, 48h - Israel, 49h - Australia, 60h - Proprietary. |
| INT dot11CurrentSet | 1.3.6.1.4.1.710.3.2.6.4.5.6 | INTEGER | read-write | This attribute represents the current set of patterns that the device is using to determine the hop sequence. The range of values is 1 to 3, and the default is 1. |
| STR dot11CurrentStationStatus | 1.3.6.1.4.1.710.3.2.6.3.8.2.1 | DisplayString | read-only | This attribute identifies the current Station Wlan status. This attribute is not available in AP's. |
| INT dot11CurrentTxAntenna | 1.3.6.1.4.1.710.3.2.6.4.3.2 | INTEGER | read-write | This attribute specifies the current antenna being used to transmit. The value is one of the following: 0 - Intelligent antennas selection, 1 - Transmitting only with antenna 1, 2 - Transmitting always with antenna 2. |
| INT dot11CurrentTxPwrLvl | 1.3.6.1.4.1.710.3.2.6.4.4.11 | INTEGER | read-write | This attribute specifies the power level, currently being used to transmit data. The value is one of the following: 0 - Low, or 1 - High. |
| STR dot11DefaultWEPKey1 | 1.3.6.1.4.1.710.3.2.6.1.3.1 | DisplayString | read-write | This attribute indicates the WEP secret key value corresponding to KeyID 1. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits). |
| STR dot11DefaultWEPKey2 | 1.3.6.1.4.1.710.3.2.6.1.3.2 | DisplayString | read-write | This attribute indicates the WEP secret key value corresponding to KeyID 2. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits). |
| STR dot11DefaultWEPKey3 | 1.3.6.1.4.1.710.3.2.6.1.3.3 | DisplayString | read-write | This attribute indicates the WEP secret key value corresponding to KeyID 3. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits). |
| STR dot11DefaultWEPKey4 | 1.3.6.1.4.1.710.3.2.6.1.3.4 | DisplayString | read-write | This attribute indicates the WEP secret key value corresponding to KeyID 4. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits). |
| dot11DefaultWEPKeys | 1.3.6.1.4.1.710.3.2.6.1.3 | |||
| INT dot11DwellRetryLimit | 1.3.6.1.4.1.710.3.2.6.2.1.5 | INTEGER | read-write | This attribute indicates the number of retransmission attempts made in several Dwells, before a failure condition is indicated. Values between 0..9 . |
| INT dot11DwellRetryLimitForVoice | 1.3.6.1.4.1.710.3.2.6.2.1.8 | INTEGER | read-write | This attribute indicates the number of retransmission for voice attempts made in several Dwells, before a failure condition is indicated. Values between 0..5 . This option is only for AP's. |
| INT dot11DwellTime | 1.3.6.1.4.1.710.3.2.6.2.1.2 | INTEGER | read-write | This attribute indicates the dwell time in Kilo-microsecond Allowed Values for version 5.x.x and higher are between 19..390. For older versions values are between 1 - 3. This attribute is available only in AP's. |
| INT dot11FragmentationThreshold | 1.3.6.1.4.1.710.3.2.6.2.1.6 | INTEGER | read-write | This attribute specifies the current maximum size, in octets, of the MPDU that will be delivered to the PHY. A frame will be broken into fragments if its size exceeds the value of this attribute, after adding MAC header and tailors. The value is one of the following: 1 - 560 octets, 2 - 800 octets, 3 - 1518 octets. |
| STR dot11JapanCallSign | 1.3.6.1.4.1.710.3.2.6.6.2 | DisplayString | read-write | This attribute indicates the Japan call sign string. Available only for Japan Standard. |
| dot11mac | 1.3.6.1.4.1.710.3.2.6.2 | |||
| dot11Maintenance | 1.3.6.1.4.1.710.3.2.6.6 | |||
| STR dot11manufacturerName | 1.3.6.1.4.1.710.3.2.6.3.8.2.3 | DisplayString | read-only | This attribute identifies the manufacturer of the resource. |
| STR dot11manufacturerProductName | 1.3.6.1.4.1.710.3.2.6.3.8.2.4 | DisplayString | read-only | This attribute identifies the manufacturer product name of the resource. |
| STR dot11manufacturerProductVersion | 1.3.6.1.4.1.710.3.2.6.3.8.2.5 | DisplayString | read-only | This attribute identifies the manufacturer's product version of the resource. |
| INT dot11MaxMulticastRate | 1.3.6.1.4.1.710.3.2.6.2.1.1 | INTEGER | read-write | This attribute indicates the basic rate for multicast frames. |
| INT dot11MultyRateDecisionWindow | 1.3.6.1.4.1.710.3.2.6.5.2 | INTEGER | read-write | This attribute indicates the multi cast rate decision window size. |
| INT dot11MultyRateSupport | 1.3.6.1.4.1.710.3.2.6.5.1 | INTEGER | read-write | This attribute indicates the multi cast rate support. |
| dot11MultySupport | 1.3.6.1.4.1.710.3.2.6.5 | |||
| dot11OperationGrp | 1.3.6.1.4.1.710.3.2.6.2.1 | |||
| dot11phy | 1.3.6.1.4.1.710.3.2.6.4 | |||
| dot11PhyAntennaGrp | 1.3.6.1.4.1.710.3.2.6.4.3 | |||
| dot11PhyFHSSGrp | 1.3.6.1.4.1.710.3.2.6.4.5 | |||
| dot11PhyOperationGrp | 1.3.6.1.4.1.710.3.2.6.4.1 | |||
| dot11PhyTxPwrGrp | 1.3.6.1.4.1.710.3.2.6.4.4 | |||
| INT dot11Preauthentication | 1.3.6.1.4.1.710.3.2.6.1.6.1 | INTEGER | read-write | This attribute, when true, enables Preauthentication algorithm. |
| dot11PrivacyGrp | 1.3.6.1.4.1.710.3.2.6.1.6 | |||
| INT dot11PrivacyInvoke | 1.3.6.1.4.1.710.3.2.6.1.6.3 | INTEGER | read-only | This attribute indicates if a special mechanism is invoked, to protect the Wireless LAN transmissions. The value is one of the following: 1 - Standard WEP, 2 - No Encryption, 20 - Special Encryption (#0), 21 - Special Encryption (#1), 22 - Special Encryption (#2) |
| INT dot11PrivacyOptionImplemented | 1.3.6.1.4.1.710.3.2.6.1.6.2 | INTEGER | read-only | This attribute, when true, shall indicate that the 802.11 WEP option is implemented. |
| dot11res | 1.3.6.1.4.1.710.3.2.6.3 | |||
| dot11resAttribute | 1.3.6.1.4.1.710.3.2.6.3.8 | |||
| dot11ResourceInfo | 1.3.6.1.4.1.710.3.2.6.3.8.2 | |||
| INT dot11RTSThreshold | 1.3.6.1.4.1.710.3.2.6.2.1.3 | INTEGER | read-write | This attribute indicates the number of bytes in an MPDU (frame), above which an RTS/CTS handshake will be performed. Setting this attribute to be larger than the maximum frame size, will prevent the RTS/CTS handshake for frames transmitted by this station. |
| INT dot11ShortRetryLimit | 1.3.6.1.4.1.710.3.2.6.2.1.4 | INTEGER | read-write | This attribute indicates the number of retransmission attempts made, before a failure condition is indicated. Values between 0..20 . |
| INT dot11ShortRetryLimitForVoice | 1.3.6.1.4.1.710.3.2.6.2.1.7 | INTEGER | read-write | This attribute indicates the number of retransmission for voice attempts made, before a failure condition is indicated. Values between 0..9 . This option is only for AP's. |
| dot11smt | 1.3.6.1.4.1.710.3.2.6.1 | |||
| CTR dot11TotalNumberOfAssocSinceLastReset | 1.3.6.1.4.1.710.3.2.6.3.8.2.2 | Counter | read-only | This attribute identifies how many time the device Associated since startup. |
| INT dot11WaitforAssociationAddress | 1.3.6.1.4.1.710.3.2.6.6.1 | INTEGER | read-write | This attribute indicates the station mac-address. 0 - Use mine 1 - Wait for update via Ethernet Available only for Stations. |
| INT dot11WEPDefaultKeyID | 1.3.6.1.4.1.710.3.2.6.1.6.4 | INTEGER | read-write | This attribute shall indicate the use of the first, second, third or fourth DefaultWEPKey when set to values of one, two, three or four. |
| INT freqNo | 1.3.6.1.4.1.710.3.2.4.2.2.6.1.2 | INTEGER | read-only | This attributes specifies the channel number of the frequency, for which this entry accumulates the statistics. |
| freqStatisticsEntry | 1.3.6.1.4.1.710.3.2.4.2.2.6.1 | not-accessible | An entry in the Frequencies Statistics table. | |
| INT freqStatisticsIndex | 1.3.6.1.4.1.710.3.2.4.2.2.6.1.1 | INTEGER | read-only | A unique value, representing the index of the frequency in the hopping sequence table |
| freqStatisticsTable | 1.3.6.1.4.1.710.3.2.4.2.2.6 | not-accessible | A table for the traffic statistics of each frequency. | |
| CTR freqTotalReceived | 1.3.6.1.4.1.710.3.2.4.2.2.6.1.3 | Counter | read-only | This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN, in that specific frequency. |
| IP gatewayIPaddr | 1.3.6.1.4.1.710.3.2.2.6 | IpAddress | read-write | Gateway default IP address. |
| IP ipAddr | 1.3.6.1.4.1.710.3.2.2.2 | IpAddress | read-write | The IP address of this device, used to access the device through any of its LAN Ports (Ethernet or WLAN). |
| ipParams | 1.3.6.1.4.1.710.3.2.2 | |||
| STR knownAPsAvrgDbm | 1.3.6.1.4.1.710.3.2.3.1.7.1.9 | DisplayString | read-only | A value representing the average Signal Strength for packets received from that AP in DBN units. |
| INT knownAPsAvrgRssi | 1.3.6.1.4.1.710.3.2.3.1.7.1.4 | INTEGER | read-only | A value representing the average Signal Strength for packets received from that AP in RSSI units. |
| knownAPsEntry | 1.3.6.1.4.1.710.3.2.3.1.7.1 | not-accessible | An entry in the Known APs table. | |
| INT knownAPsGoodBeacons | 1.3.6.1.4.1.710.3.2.3.1.7.1.7 | INTEGER | read-only | A value representing the number of beacons received with Strength more then join level from that AP. |
| INT knownAPsIndex | 1.3.6.1.4.1.710.3.2.3.1.7.1.1 | INTEGER | read-only | A unique value, representing the index of the AP in the Known APs table |
| INT knownAPsLoadStations | 1.3.6.1.4.1.710.3.2.3.1.7.1.6 | INTEGER | read-only | A value representing the number of stations associated to that AP. |
| INT knownAPsQuality | 1.3.6.1.4.1.710.3.2.3.1.7.1.3 | INTEGER | read-only | This attribute specifies the current reception quality of frames, transmitted by that AP. At a station, a GOOD value indicates that the station can join that AP. |
| INT knownAPsStatus | 1.3.6.1.4.1.710.3.2.3.1.7.1.5 | INTEGER | read-write | The validity of the current entry, either invalid or valid. |
| knownAPsTable | 1.3.6.1.4.1.710.3.2.3.1.7 | not-accessible | A table of identities of the most recently known Access Points, and their signal quality. | |
| INT knownAPsTotalBeacons | 1.3.6.1.4.1.710.3.2.3.1.7.1.8 | INTEGER | read-only | A value representing the total number of beacons (good and bad) received from that AP. |
| MAC knownAPsValue | 1.3.6.1.4.1.710.3.2.3.1.7.1.2 | MacAddress | read-write | This attributes specifies the address of a recently known AP. The default value of this attribute shall be null (an empty entry). |
| IP maskIP | 1.3.6.1.4.1.710.3.2.2.3 | IpAddress | read-write | The IP Network mask used by the IP entity when accessing devices through any of its LAN Ports (Ethernet or WLAN). |
| INT powerSaveAged | 1.3.6.1.4.1.710.3.2.4.5.5.1.4 | INTEGER | read-only | This attributes specifies how many Stations were deleted after long time of waiting |
| INT powerSaveBuffered | 1.3.6.1.4.1.710.3.2.4.5.5.1.3 | INTEGER | read-only | This attributes specifies how many messages are waiting to that Station in the AP buffers |
| INT powerSaveIndex | 1.3.6.1.4.1.710.3.2.4.5.5.1.1 | INTEGER | read-only | A unique value, representing the index of the frequency in the hopping sequence table |
| INT powerSaveQueueFull | 1.3.6.1.4.1.710.3.2.4.5.5.1.6 | INTEGER | read-only | This attributes specifies how many messages were discarded because the queue to that station was full |
| INT powerSaveSent | 1.3.6.1.4.1.710.3.2.4.5.5.1.5 | INTEGER | read-only | This attributes specifies how many messages were sent to that station |
| INT powerSaveStationID | 1.3.6.1.4.1.710.3.2.4.5.5.1.2 | INTEGER | read-only | The identifier numerator of the Station in the AP. Note : ID zero is Broadcast. |
| powreStationsEntry | 1.3.6.1.4.1.710.3.2.4.5.5.1 | not-accessible | A trap-receiving host entry, containing trap-host objects for a particular host. | |
| powreStationsTable | 1.3.6.1.4.1.710.3.2.4.5.5 | not-accessible | A list of trap-hosts entries. | |
| CTR probeRequestRecive | 1.3.6.1.4.1.710.3.2.4.4.1.4 | Counter | read-only | For an AP: Number of Probe request frames that has received. |
| CTR probeResponseLost | 1.3.6.1.4.1.710.3.2.4.4.1.2 | Counter | read-only | For an AP: Number of Probe response that got lost. |
| CTR probeResponseSent | 1.3.6.1.4.1.710.3.2.4.4.1.1 | Counter | read-only | For an AP: Number of Probe response that sent. |
| CTR probeResponseSentRetx | 1.3.6.1.4.1.710.3.2.4.4.1.3 | Counter | read-only | For an AP: Number of retransmitted Probe response frames that sent. |
| CTR probRequestSent | 1.3.6.1.4.1.710.3.2.4.4.2.1 | Counter | read-only | For WB or SA: Number of Probe request frames that sent. |
| CTR probResponceRecive | 1.3.6.1.4.1.710.3.2.4.4.2.2 | Counter | read-only | For WB or SA: Number of received Probe response frames. |
| CTR pSFreeEntries | 1.3.6.1.4.1.710.3.2.4.5.1 | Counter | read-only | For an AP: Number of station free entries. |
| CTR pSInternallydiscarded | 1.3.6.1.4.1.710.3.2.4.5.2 | Counter | read-only | For an AP: Number of Internally Discarded frames. |
| CTR pSPowerSavingAged | 1.3.6.1.4.1.710.3.2.4.5.4 | Counter | read-only | For an AP: Number of frames that were not transmitted due to the end of aging time. |
| CTR pSstations | 1.3.6.1.4.1.710.3.2.4.5.3 | Counter | read-only | For an AP: Number of power saved station connected to this AP. |
| STR readCommunity | 1.3.6.1.4.1.710.3.2.2.4 | DisplayString | read-write | The device read community. If updated, it will be used after the next reset. |
| CTR reAssocRequestRecive | 1.3.6.1.4.1.710.3.2.4.4.1.9 | Counter | read-only | For an AP: Number of ReAssociation request frames that has received. |
| MAC stAddress | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.1 | MacAddress | read-only | The MAC Address of the station represented by this entry in the Association Data Base |
| INT stCFMode | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.4 | INTEGER | read-only | This attribute is set to ON if the station is in the Contention Free Polling list of the AP. |
| INT stCurTxRate | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.6 | INTEGER | read-only | The rate currently used by the AP to transmit packets to this station |
| STR stDbm | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.23 | DisplayString | read-only | A value representing the average Signal Strength for packets received from that station in DBM units. This attribute is being updated only if sysCollectPerStationInfo is set to ON. |
| INT stMaxRate | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.5 | INTEGER | read-only | This attribute indicates the maximum rate (in Mbits per second) at which that station transmits data across the Wireless medium. |
| INT stPMMode | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.8 | INTEGER | read-only | The current Power Management mode of this station Power saving mode enables WLAN units (such as laptops or hand-held devices) to conserve battery power. To enable this feature, first enable power saving for the AP, and then enable power saving in the SA-PCR Card. |
| INT stResetCounters | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.17 | INTEGER | read-write | Setting the value of this attribute to ON, will clear the station counters at the AP (clear the counters in that adbEntry). Warning: Setting the value of this attribute to ON may cause momentary degradation in performance |
| CTR stReTxFragments1M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.20 | Counter | read-only | This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stReTxFragments2M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.21 | Counter | read-only | This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stReTxFragments3M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.22 | Counter | read-only | This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| INT stRssi | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.7 | INTEGER | read-only | A value representing the average Signal Strength for packets received from that station in RSSI units. This attribute is being updated only if sysCollectPerStationInfo is set to ON. |
| CTR stRxFragments | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.15 | Counter | read-only | This attribute counts the total number of fragments (data and management) that have been received successfully from that station, through the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxDroppedPackets | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.14 | Counter | read-only | This attribute counts the number of transmit frames (data or management) to this station, that were dropped because of too many retransmissions. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxFragments | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.9 | Counter | read-only | This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxFragments1M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.10 | Counter | read-only | This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxFragments2M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.11 | Counter | read-only | This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxFragments3M | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.12 | Counter | read-only | This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 3Mbps. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxRetry | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.13 | Counter | read-only | This attribute counts the total number of retransmissions to that station, over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON. |
| CTR stTxRetryPercent | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.19 | Counter | read-only | This attribute calculate the retransmitted percentage, that was retransmitted to that station over the Wireless LAN. |
| INT stType | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.18 | INTEGER | read-only | This attribute identifies the device type of the station. |
| INT stWlanStatus | 1.3.6.1.4.1.710.3.2.3.2.2.1.1.16 | INTEGER | read-only | This attribute specifies the current reception quality of frames, transmitted by that station. |
| INT sysCarrierSense | 1.3.6.1.4.1.710.3.2.1.1.6 | INTEGER | read-write | This attribute defines the carrier sense absolute threshold |
| STR sysChangeInstallerPassword | 1.3.6.1.4.1.710.3.2.1.1.10.5 | DisplayString | read-write | This attribute let you change the Installer Password of that station. Type the new password, maximum 8 characters. |
| STR sysChangeRightsToINSTALLER | 1.3.6.1.4.1.710.3.2.1.1.10.3 | DisplayString | read-write | This attribute let you change the access rights of that station to INSTALLER. Type the Installer password for the desired access right. |
| STR sysChangeRightsToTECHNICIAN | 1.3.6.1.4.1.710.3.2.1.1.10.4 | DisplayString | read-write | This attribute let you change the access rights of that station to AUTHORIZED TECHNICIAN. Type the Technician password for the desired access right. |
| INT sysChangeRightsToUSER | 1.3.6.1.4.1.710.3.2.1.1.10.2 | INTEGER | read-write | This attribute let you change the access rights of that station to USER. |
| sysCmd | 1.3.6.1.4.1.710.3.2.1.1 | |||
| INT sysDeltaCarrierSense | 1.3.6.1.4.1.710.3.2.1.1.7 | INTEGER | read-write | This attribute defines the carrier sense differential threshold |
| INT sysDisplayAccessRights | 1.3.6.1.4.1.710.3.2.1.1.10.1 | INTEGER | read-only | This attribute Display the access rights of that station. |
| INT sysExternalAmplifier | 1.3.6.1.4.1.710.3.2.1.1.12 | INTEGER | read-write | This attribute is set to 1 when external amplifier is connected to the device and set to 0 when device is connected to anntena. |
| INT sysNoiseFloor | 1.3.6.1.4.1.710.3.2.1.1.11 | INTEGER | read-write | This attribute defines the low RSSI threshold in DBM units. Allowed range is from -120 to -50 dbm. |
| sysParams | 1.3.6.1.4.1.710.3.2.1.2 | |||
| INT sysPartialDefaults | 1.3.6.1.4.1.710.3.2.1.1.8 | INTEGER | read-write | Setting the value of this attribute to ON will cause the system to set the partial NVRAM parameters to the factory default values. These values will become active after the next system reset |
| INT sysReset | 1.3.6.1.4.1.710.3.2.1.1.1 | INTEGER | read-write | Setting the value of this attribute to ON is interpreted as a reset command for the system. |
| INT sysResetCounters | 1.3.6.1.4.1.710.3.2.1.1.3 | INTEGER | read-write | Setting the value of this attribute to ON will cause the system to clear the performance counters. |
| INT sysRunFromNonActiveCode | 1.3.6.1.4.1.710.3.2.1.1.9 | INTEGER | read-write | This attribute make you run from non active code. Automatic switch is done if the non active code is valid. To activate set to On. If the switch succeed no response will be sent to the SNMP browser. |
| INT sysSetDefaults | 1.3.6.1.4.1.710.3.2.1.1.2 | INTEGER | read-write | Setting the value of this attribute to ON will cause the system to set the NVRAM parameters to the factory default values. These values will become active after the next system reset |
| CTR sysTrapCounter | 1.3.6.1.4.1.710.3.2.1.1.5 | Counter | read-only | This attribute counts the total number of traps generated by the device, since initialization. |
| INT sysTrapEnable | 1.3.6.1.4.1.710.3.2.1.1.4 | INTEGER | read-write | Setting the value of this attribute to OFF will disable the system from sending TRAPs. |
| STR trapCommunity | 1.3.6.1.4.1.710.3.2.2.1.1.3 | DisplayString | read-write | The community of the host to be sent all traps |
| trapHostsEntry | 1.3.6.1.4.1.710.3.2.2.1.1 | not-accessible | A trap-receiving host entry, containing trap-host objects for a particular host. | |
| INT trapHostsIndex | 1.3.6.1.4.1.710.3.2.2.1.1.1 | INTEGER | read-only | A unique value for each trap-host. Its value ranges between 1 and 3 |
| trapHostsTable | 1.3.6.1.4.1.710.3.2.2.1 | not-accessible | A list of trap-hosts entries. | |
| IP trapIPaddress | 1.3.6.1.4.1.710.3.2.2.1.1.2 | IpAddress | read-write | The IP address of the host to be sent all traps |
| STR writeCommunity | 1.3.6.1.4.1.710.3.2.2.5 | DisplayString | read-write | The device write community. If updated, it will be used after the next reset. |
RFC description
Manages BreezeNet wireless LAN product series with support for system commands and monitoring.
Start monitoring BreezeCOM (Alvarion) wireless bridges/fixed wireless radios (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.