| OID symbolic | OID numeric | Type | Access | Description |
|---|
| bcsSimulcryptScs | 1.3.6.1.4.1.1166.7.7 | | | The Simulcrypt SCS MIB module for Motorola BCS products. |
| bcsSimScsConfig | 1.3.6.1.4.1.1166.7.7.1 | | | |
| bcsSimScsConfigGeneral | 1.3.6.1.4.1.1166.7.7.1.1 | | | |
| U32 bcsSimScsNetworkId | 1.3.6.1.4.1.1166.7.7.1.1.1 | Unsigned32 | read-write | This parameter specifies the network ID used for this
Simulcrypt system. The network ID is a Simulcrypt system
parameter, please see Simulcrypt system specifications
for a more detailed explanation.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| U32 bcsSimScsMaxNetworkDelay | 1.3.6.1.4.1.1166.7.7.1.1.2 | Unsigned32 | read-write | Worst case propagation delay, in milliseconds, introduced by
network topology. Will be factored into negotiations of the
actual Simulcrypt crypto-period.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| U32 bcsSimScsNominalCryptoPeriod | 1.3.6.1.4.1.1166.7.7.1.1.3 | Unsigned32 | read-write | This value specifies the nominal crypto-period in seconds.
This value is used as a target for this device during crypto-
period negotiations. The actual negotiated crypto-period may
be equal to or greater than this value.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| INT bcsSimScsAccessCriteriaSource | 1.3.6.1.4.1.1166.7.7.1.1.4 | INTEGER | read-write | This value specifies which vendor will provide the access
criteria information.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| U32 bcsSimScsEcmgTimeout | 1.3.6.1.4.1.1166.7.7.1.1.5 | Unsigned32 | read-write | This parameter specifies how long the SCS should wait for a
response from the ECMG. This value is specified in seconds.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| U32 bcsSimScsEcmIdInitial | 1.3.6.1.4.1.1166.7.7.1.1.6 | Unsigned32 | read-write | Each ECM ID and Super CAS ID combination in the Simulcrypt
system must be globally unique. To simplify configuration,
each SCS is given a starting ECM ID to assign to the first
ECM stream it creates. The number is incremented as new
ECM streams are created. Each SCS must be configured with a
different value. The initial values should be spaced
sufficiently to prevent overlapping. Recommended spacing
is 128.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| U32 bcsSimScsEcmChannelTestPeriodicity | 1.3.6.1.4.1.1166.7.7.1.1.7 | Unsigned32 | read-write | Periodicity for the channel test procedure.Default set to 20sec.
@Range(min=1, max=3600)
@Config(config=yes, reboot=no)
@Save(semSaveConfig, value=2, default=yes)
@File(config.ini, type='ini') |
| U32 bcsSimScsEcmNetworkDelay | 1.3.6.1.4.1.1166.7.7.1.1.8 | Unsigned32 | read-write | The network delay value to account for delays
while waiting on an ECM response.Default set to 500msec.
@Range(min=0, max=30000)
@Config(config=yes, reboot=no)
@Save(semSaveConfig, value=2, default=yes)
@File(config.ini, type='ini') |
| U32 bcsSimScsEcmReplyTimeout | 1.3.6.1.4.1.1166.7.7.1.1.9 | Unsigned32 | read-write | Time to wait before timing out while waiting on a response
to a channel/stream management message (i.e.: channel_setup,
channel_test, stream_setup).Default set to 4000 msec.
@Range(min=100, max=60000)
@Config(config=yes, reboot=no)
@Save(semSaveConfig, value=2, default=yes)
@File(config.ini, type='ini') |
| bcsSimScsEcmgConnectionTable | 1.3.6.1.4.1.1166.7.7.1.2 | | not-accessible | This table persists the Simulcrypt SCS to ECMG connections
or channels. The device will send Simulcrypt control words to
a maximum of bcsSimScsMaxEcmg. |
| bcsSimScsEcmgConnectionEntry | 1.3.6.1.4.1.1166.7.7.1.2.1 | | not-accessible | A single entry in the bcsSimScsEcmgConnectionTable table. |
| I32 bcsSimScsEcmgConnectIndex | 1.3.6.1.4.1.1166.7.7.1.2.1.1 | Integer32 | not-accessible | The Simulcrypt ECMG Connection table index. |
| ENA bcsSimScsEcmgConnectEnabled | 1.3.6.1.4.1.1166.7.7.1.2.1.2 | EnableDisableTYPE | read-write | Each row in the bcsSimScsEcmgConnectionTable represents a
potential SCSECMG connection that will be attempted
during simulcrypt SCS initialization.
This setting controls whether or not the attempt is made.
This setting has two legal settings:
disabled (1) <= The connection will be attempted.
enabled (2) <= The connection will not be attempted.
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take effect. |
| U32 bcsSimScsEcmgConnectSuperCasId | 1.3.6.1.4.1.1166.7.7.1.2.1.3 | Unsigned32 | read-write | The Super CAS ID of the ECMG that will be connected to by
the Simulcrypt SCS. The Super CAS ID is the 32 bit concatenation
of the CAS ID and the Sub CAS ID. The CAS ID identifies the
Conditional Access provider. It supplies the
upper 16 bits of the SuperCAS ID. The Sub CAS ID identifies
instances of a provider's ECMGs on the Simulcrypt network.
It supplies the lower 16 bits of the Super CAS ID.
Each ECM ID and SuperCAS ID combination in the Simulcrypt
system must be globally unique.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| IP bcsSimScsEcmgConnectIpAddr | 1.3.6.1.4.1.1166.7.7.1.2.1.4 | IpAddress | read-write | The IP address that the ECMG is listening on.
Used to open a socket between the SCS and the ECMG.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| I32 bcsSimScsEcmgConnectPort | 1.3.6.1.4.1.1166.7.7.1.2.1.5 | Integer32 | read-write | The remote port that the ECMG is listening on.
Used to open a socket between the SCS and the ECMG.
SEM Note:
Once written, a save must be performed via the semSaveConfig
parameter and the SEM must be rebooted for the change to take
effect. |
| bcsSimScsEcmgRedundancyConfigTable | 1.3.6.1.4.1.1166.7.7.1.3 | | not-accessible | This table configures parameters associated with the ECMG redudancy feature.
@Commit(param=bcsSimScsEcmgRedundancyConfigApplyChange, value=2)
@Save(semSaveConfig, value=2)
@File(config.ini, type='ini') |
| bcsSimScsEcmgRedundancyConfigEntry | 1.3.6.1.4.1.1166.7.7.1.3.1 | | not-accessible | A single entry in bcsSimScsEcmgRedundancyConfigTable. |
| I32 bcsSimScsEcmgRedundancyConfigIndex | 1.3.6.1.4.1.1166.7.7.1.3.1.1 | Integer32 | not-accessible | Index into the table. |
| ENA bcsSimScsEcmgRedundancyConfigAutoSwitchBack | 1.3.6.1.4.1.1166.7.7.1.3.1.2 | EnableDisableTYPE | read-write | If enabled (2), programs (which were taken away earlier
from this ECMG upon its failure) will be automatically switched back
to this ECMG after its recovery.
If disabled (1), such an automatic switching will not happen.
Detailed semantics are captured in requirements.Default value is enabled. |
| MAN bcsSimScsEcmgRedundancyConfigManualSwitchBack | 1.3.6.1.4.1.1166.7.7.1.3.1.3 | ManualSwitchBackTYPE | read-write | When autoswitchback is enabled manual switch back is
notActive.When manual switch back Button get pressed Manual switch back state get changed from manualSwitchBackNotInProgress(1) to
(2)manualSwitchBack.Then the programs (which were taken away earlier from this ECMG upon its failure)will be switched back to it.
Once the switchback progress get finished ,manual switch back state changed to (1) manualSwitchBackNotInProgress. |
| I32 bcsSimScsEcmgRedundancyConfigMaxStreams | 1.3.6.1.4.1.1166.7.7.1.3.1.4 | Integer32 | read-write | Maximum number of streams supported.The default value is 128.
@Config(config=yes, reboot=yes) |
| bcsSimScsEcmgRedundancyConfigApplyTable | 1.3.6.1.4.1.1166.7.7.1.4 | | not-accessible | Table of Apply Change for the data for bcsSimScsEcmgRedundancyConfigTable.
A row of this table corresponds to a row in bcsSimScsEcmgRedundancyConfigTable. |
| bcsSimScsEcmgRedundancyConfigApplyEntry | 1.3.6.1.4.1.1166.7.7.1.4.1 | | not-accessible | ECMG Redundancy Configuration Apply Table Entry. |
| I32 bcsSimScsEcmgRedundancyConfigApplyIndex | 1.3.6.1.4.1.1166.7.7.1.4.1.1 | Integer32 | not-accessible | ECMG index - also maps to the bcsSimScsEcmgRedundancyConfigTable index |
| APP bcsSimScsEcmgRedundancyConfigApplyChange | 1.3.6.1.4.1.1166.7.7.1.4.1.2 | ApplyDataToDeviceTYPE | read-write | The Apply for a row of data in bcsSimScsEcmgRedundancyConfigTable.
A row in this table corresponds to the same row index in the
bcsSimScsEcmgRedundancyConfigTable.
This parameter MUST be set to 'apply' in order for any of the data
in the rows to take effect in the SEM. This parameter MUST be set
LAST after all other data in the configuration table rows has been
configured.
@Config(config=no, reboot=no) |
| bcsSimScsStatus | 1.3.6.1.4.1.1166.7.7.2 | | | |
| bcsSimScsStatusGeneral | 1.3.6.1.4.1.1166.7.7.2.1 | | | |
| INT bcsSimScsMibSupportStatus | 1.3.6.1.4.1.1166.7.7.2.1.1 | INTEGER | read-only | Indicates whether the device is capable of supporting and/or
enabled to support the functionality of the bcsSimulcryptScs MIB. |
| U32 bcsSimScsMaxEcmg | 1.3.6.1.4.1.1166.7.7.2.1.2 | Unsigned32 | read-only | The maximum number of ECMGs this device can support. |
| U32 bcsSimScsMaxPrograms | 1.3.6.1.4.1.1166.7.7.2.1.3 | Unsigned32 | read-only | The maximum number of programs this device can support. |
| U32 bcsSimScsMaxProgramEcmg | 1.3.6.1.4.1.1166.7.7.2.1.4 | Unsigned32 | read-only | The maximum number of ECMGs that can be associated with a
program in this device. |
| STR bcsSimScsEcmgRedundancyConfigInvalidApplyText | 1.3.6.1.4.1.1166.7.7.2.1.5 | DisplayString | read-only | When bcsSimScsEcmgRedundancyConfigApplyChange is set to
'applyNotInProgressInvalidData' this entry may contain
a text description of what was wrong with the data. This
entry contains the description for the most recent apply
of a related entry that was invalid. |
| bcsSimScsEcmgStatusTable | 1.3.6.1.4.1.1166.7.7.2.2 | | not-accessible | It contains status information for the SCS to ECMG connections.
There can be up to bcsSimScsMaxEcmg active SCS to ECMG
connections at a time. |
| bcsSimScsEcmgStatusEntry | 1.3.6.1.4.1.1166.7.7.2.2.1 | | not-accessible | A single entry in the bcsSimScsEcmgStatusTable table. |
| I32 bcsSimScsEcmgStatusIndex | 1.3.6.1.4.1.1166.7.7.2.2.1.1 | Integer32 | not-accessible | This index is used to traverse the bcsSimScsEcmgTable table.
The index varies from 1..bcsSimScsMaxEcmg. In the event
that some connections are not active this will be designated
by the value of bcsSimScsEcmgChannelState. |
| INT bcsSimScsEcmgTcpState | 1.3.6.1.4.1.1166.7.7.2.2.1.2 | INTEGER | read-only | This column specifies TCP connection state of this
SCS ECMG connection. |
| U32 bcsSimScsEcmgChannelId | 1.3.6.1.4.1.1166.7.7.2.2.1.3 | Unsigned32 | read-only | This column specifies channel ID. |
| INT bcsSimScsEcmgChannelState | 1.3.6.1.4.1.1166.7.7.2.2.1.4 | INTEGER | read-only | This column specifies ECMG channel state of this
SCS ECMG connection. |
| U32 bcsSimScsEcmgSuperCasId | 1.3.6.1.4.1.1166.7.7.2.2.1.5 | Unsigned32 | read-only | This column specifies super CAS Id of the ECMG that
the SCS is connected to on this connection. |
| bcsSimScsProgramTable | 1.3.6.1.4.1.1166.7.7.2.3 | | not-accessible | It contains status information for the SCS programs.
There can be up to bcsSimScsMaxPrograms
Simulcrypt programs active in the SCS at a time.
Each program can be associated with up to
bcsSimScsMaxProgramEcmg. |
| bcsSimScsProgramEntry | 1.3.6.1.4.1.1166.7.7.2.3.1 | | not-accessible | A single entry in the bcsSimScsProgramTable table. |
| I32 bcsSimScsProgramIndex | 1.3.6.1.4.1.1166.7.7.2.3.1.1 | Integer32 | not-accessible | This index is used to traverse the bcsSimScsProgramTable
table. Limited by bcsSimScsMaxPrograms. |
| I32 bcsSimScsProgramEcmgIndex | 1.3.6.1.4.1.1166.7.7.2.3.1.2 | Integer32 | not-accessible | ECMG index. This index is used to traverse the
bcsSimScsProgramTable table.
Limited by bcsSimScsMaxProgramEcmg. |
| INT bcsSimScsProgramState | 1.3.6.1.4.1.1166.7.7.2.3.1.3 | INTEGER | read-only | This column displays the service state of this program.
(1) - program configured, no event running
(2) - program configured, event running normally
(3) - program not configured |
| U32 bcsSimScsProgramCryptoPeriod | 1.3.6.1.4.1.1166.7.7.2.3.1.4 | Unsigned32 | read-only | This column displays the actual crypto-period in
seconds that is in use for this program. |
| U32 bcsSimScsProgramChannelId | 1.3.6.1.4.1.1166.7.7.2.3.1.5 | Unsigned32 | read-only | This column displays the channel ID. |
| U32 bcsSimScsProgramEcmgSuperCasId | 1.3.6.1.4.1.1166.7.7.2.3.1.6 | Unsigned32 | read-only | This column displays the Super CAS-ID of the 1st
ECMG on this service. |
| INT bcsSimScsProgramEcmgStreamState | 1.3.6.1.4.1.1166.7.7.2.3.1.7 | INTEGER | read-only | This column displays the stream state for an ECMG
on this service. |
