ARUBAWIRED-LLDP-MIB

All MIBs › ARUBAWIRED-LLDP-MIB

Organization: HPE/Aruba Networking Division

Last Updated: 2019-04-15

Category: Vendor: Aruba, Wireless and WLAN

Description: Aruba wired switch ArubaOS-CX LLDP neighbor discovery and topology information management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ARUBAWIRED-LLDP-MIB?

ARUBAWIRED-LLDP-MIB is a vendor-specific SNMP module for HPE Aruba wired switches running ArubaOS-CX, extending the standard IEEE 802.3/LLDP-MED power-via-MDI objects to report Power Sourcing Equipment (PSE) information over LLDP. It exposes per-port LLDP power data including power class, MDI support/enable state, pair control capability, power source, power priority, and PD (powered device) requested power values. In terms of hardware/software status monitoring, this MIB is specifically useful for tracking Power-over-Ethernet health and negotiation on switch ports - verifying whether a port's PSE power class, source, and priority match what a connected powered device requested, which is critical for diagnosing PoE delivery problems to devices like VoIP phones, APs, or cameras. It is explicitly derived from and extends the IEEE 802.3/LLDP-MED PSE MIB objects (lldpXdot3LocPower structures), reusing that standard's structure. Typical deployment context is enterprise wired switch infrastructure delivering PoE to edge devices, monitored via ArubaOS-CX-based switches. Engineers can download the ARUBAWIRED-LLDP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ARUBAWIRED-LLDP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HPE Aruba wired switch (ArubaOS-CX)

Monitoring Examples

An administrator would poll arubaWiredLldpXdot3LocPowerTable/Entry per port to check arubaWiredLldpXdot3LocPowerClass and arubaWiredLldpXdot3LocPowerSource, confirming a switch port is sourcing the correct PoE class to an attached device. Comparing arubaWiredLldpXdot3LocPDRequestedPowerValue against the port's actual power class can reveal under-provisioning where a connected AP or phone requests more power than the port class allows. Checking arubaWiredLldpXdot3LocPowerMDIEnabled and arubaWiredLldpXdot3LocPowerPairControlable helps confirm whether MDI power delivery is active and configurable on that port.

What Can Be Monitored

PoE power class per port
PSE power source and priority
MDI power support/enable state
PD requested power value
power pair controllability

Imported Objects

From ARUBAWIRED-NETWORKING-OID

wndFeatures

OBJECT-IDENTITY

From ENTITY-MIB

entPhysicalIndex

OBJECT-TYPE

From LLDP-MIB

lldpLocPortNum	OBJECT-TYPE
lldpRemIndex	OBJECT-TYPE
lldpRemLocalPortNum	OBJECT-TYPE
lldpRemTimeMark	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
arubaWiredLldpCompliances	1.3.6.1.4.1.47196.4.1.1.3.9.2.1
arubaWiredLldpConformance	1.3.6.1.4.1.47196.4.1.1.3.9.2
arubaWiredLldpGroups	1.3.6.1.4.1.47196.4.1.1.3.9.2.2
INT arubaWiredLldpLocPdTlvSentType	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.27	INTEGER	read-only	This field specifies the set of TLVs that are actually sent by the PD
INT arubaWiredLldpLocPseTlvSentType	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.26	INTEGER	read-only	This field specifies the set of TLVs that are actually sent by the PSE
arubaWiredLldpMIB	1.3.6.1.4.1.47196.4.1.1.3.9			This MIB module describes management objects that manage LLDP information related to Power Source Equipment (PSE). This is the MIB module related to HPE Aruba LLDP
arubaWiredLldpXdot3Compliance	1.3.6.1.4.1.47196.4.1.1.3.9.2.1.1			The compliance statement for LLDP implementation.
arubaWiredLldpXdot3LocalData	1.3.6.1.4.1.47196.4.1.1.3.9.1.1
T/F arubaWiredLldpXdot3LocAutoclassCompleted	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.25	TruthValue	read-only	It indicates whether the local PSE system has completed the Autoclass measurement
T/F arubaWiredLldpXdot3LocPDLoad	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.22	TruthValue	read-only	The truth value used to indicate whether the load of a dual- signature PD is electrically isolated. For a single-signature PD, or a PSE, the value of this attribute is FALSE.
I32 arubaWiredLldpXdot3LocPDRequestedPowerValue	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.10	Integer32	read-only	It indicates the maximum input average power the PD is requesting in units of 0.1 W.
I32 arubaWiredLldpXdot3LocPDRequestedPowerValueA	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.11	Integer32	read-only	It indicates the PD requested power value for the Mode A pairset in units of 0.1 W.
I32 arubaWiredLldpXdot3LocPDRequestedPowerValueB	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.12	Integer32	read-only	It indicates the PD requested power value for the Mode B pairset in units of 0.1 W.
INT arubaWiredLldpXdot3LocPowerClass	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.6	INTEGER	read-only	The truth value that indicates the requested Class of the PD.
INT arubaWiredLldpXdot3LocPowerClassExt	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.20	INTEGER	read-write	For a single-signature PD, it indicates the requested Class during Physical Layer Classification. For a dual-signature PD, the value is set to 'dualsig'. For a PSE connected to a single-signature PD or a PSE that operates only in 2-pair mode, a readonly value that indicates the currently assigned Class. For a PSE connected to a dualsignature PD, a read-only value set to 'dualsig'.
INT arubaWiredLldpXdot3LocPowerClassExtA	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.18	INTEGER	read-write	For a dual-signature PD, it indicates the requested Class for Mode A during Physical Layer Classification. For a single-signature PD, a read-only value set to 'singlesig'. For a PSE connected to a dual-signature PD, a read-only value that indicates the currently assigned Class for Mode A. For a PSE connected to a single-signature PD, or a PSE that operates only in 2-pair mode, the value is set to 'singlesig'
INT arubaWiredLldpXdot3LocPowerClassExtB	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.19	INTEGER	read-write	For a dual-signature PD, it indicates the requested Class for Mode B during Physical Layer Classification. For a single-signature PD, a read-only value set to 'singlesig'. For a PSE connected to a dual-signature PD, a read-only value that indicates the currently assigned Class for Mode B. For a PSE connected to a single-signature PD, or a PSE that operates only in 2-pair mode, the value is set to 'singlesig'
arubaWiredLldpXdot3LocPowerEntry	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1		not-accessible	Information about a particular port component.
T/F arubaWiredLldpXdot3LocPowerMDIEnabled	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.3	TruthValue	read-only	The truth value used to indicate whether the MDI power is enabled on given port associated with the local system.
T/F arubaWiredLldpXdot3LocPowerMDISupported	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.2	TruthValue	read-only	The truth value used to indicate whether the MDI power is supported on the given port associated with the local system.
T/F arubaWiredLldpXdot3LocPowerPairControlable	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.4	TruthValue	read-only	The truth value used to indicate the ability to control which PSE Pinout Alternative is used for PD detection and power.
INT arubaWiredLldpXdot3LocPowerPairs	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.5	INTEGER	read-only	The truth value that identifies the PSE Pinout Alternative in use for detecting and supplying power to the PD.
INT arubaWiredLldpXdot3LocPowerPairsExt	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.17	INTEGER	read-write	This field indicates the supported PSE Pinout Alternative. For a PD the contents of this attribute are undefined
INT arubaWiredLldpXdot3LocPowerPortClass	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.1	INTEGER	read-only	The value that identifies the port Class of the given port associated with the local system.
INT arubaWiredLldpXdot3LocPowerPriority	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.9	INTEGER	read-write	This field reflects the requested local device power priority. When the power type is PD, this field shall be set to the power priority configured for the device. If a PD is unable to determine its power priority or it has not been configured, then this field shall be set to unknown(1). When the power type is PSE, this field shall be set to unknown(1).
INT arubaWiredLldpXdot3LocPowerSource	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.8	INTEGER	read-only	This field reflects the requested local device power source. When the power type is PSE, this field shall be set to primary(2) when the PSE is sourcing its power through the PI from its primary supply; to backup(3) when the PSE is sourcing its power through the PI from a backup source; and to unknown(1) when this information is not available.
arubaWiredLldpXdot3LocPowerTable	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1		not-accessible	This table contains one row per port of power ethernet information (as a part of the LLDP 802.3bt organizational extension) on the local system known to this agent.
INT arubaWiredLldpXdot3LocPowerType	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.7	INTEGER	read-only	This field reflects the actual local power type.
INT arubaWiredLldpXdot3LocPowerTypeExt	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.21	INTEGER	read-only	This field indicates if the local system is a Type 3 or Type 4 PSE or PD, and in the case of a Type 3 or Type 4 PD, if it is a single-signature PD or a dual-signature PD
I32 arubaWiredLldpXdot3LocPSEAllocatedPowerValue	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.13	Integer32	read-only	It indicates the maximum input average power the PSE expects the PD to draw in units of 0.1 W.
I32 arubaWiredLldpXdot3LocPSEAllocatedPowerValueA	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.14	Integer32	read-only	It indicates the maximum input average power levels the PSE expects the dual-signature PD to draw, in units of 0.1 W, on Alternative A, when the PSE provides power over 4-pair.
I32 arubaWiredLldpXdot3LocPSEAllocatedPowerValueB	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.15	Integer32	read-only	It indicates the maximum input average power levels the PSE expects the dual-signature PD to draw, in units of 0.1 W, on Alternative B, when the PSE provides power over 4-pair.
T/F arubaWiredLldpXdot3LocPSEAutoclassSupport	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.24	TruthValue	read-only	It indicates whether the local PSE system supports Autoclass
I32 arubaWiredLldpXdot3LocPSEMaxAvailPower	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.23	Integer32	read-only	It indicates the local PSE maximum available power value in units of 0.1 W.
INT arubaWiredLldpXdot3LocPSEPoweringStatus	1.3.6.1.4.1.47196.4.1.1.3.9.1.1.1.1.16	INTEGER	read-write	This field reflects the existing powering configuration of the PSE and thus indicates that the PSE is using the 'PSE allocated power value' field or is using the 'PSE allocated power value Alternative A' field and 'PSE allocated power value Alternative B' field. For a PD the contents of this attribute are undefined.
arubaWiredLldpXdot3LocSysGroup	1.3.6.1.4.1.47196.4.1.1.3.9.2.2.1			The collection of objects which are used to represent LLDP 802.3 organizational extension for POEP Local Device Information. This group is mandatory for agents which implement the LLDP 802.3 organizational extension for POEP.
arubaWiredLldpXdot3Objects	1.3.6.1.4.1.47196.4.1.1.3.9.1
T/F arubaWiredLldpXdot3RemAutoclassRequest	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.24	TruthValue	read-only	It indicates whether the remote PD system is requesting an Autoclass measurement
arubaWiredLldpXdot3RemoteData	1.3.6.1.4.1.47196.4.1.1.3.9.1.2
T/F arubaWiredLldpXdot3RemPD4PID	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.22	TruthValue	read-only	The truth value used to indicate whether the remote PD system supports powering of both PD Modes
T/F arubaWiredLldpXdot3RemPDLoad	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.21	TruthValue	read-only	The truth value used to indicate whether the load of the remote dual-signature PD is electrically isolated. For a PD this attribute is set to FALSE
INT arubaWiredLldpXdot3RemPDPoweredStatus	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.16	INTEGER	read-write	This field indicates the existing powered configuration of the PD and thus indicate that the PD is using the 'PD requested power value' field or is using the 'PD requested power value Mode A' field and the 'PD requested power value Mode B' field. For a PSE the contents of this attribute are undefined.
I32 arubaWiredLldpXdot3RemPDRequestedPowerValue	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.10	Integer32	read-only	It indicates the maximum input average power the PD is requesting in units of 0.1 W.
I32 arubaWiredLldpXdot3RemPDRequestedPowerValueA	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.11	Integer32	read-only	It indicates the PD requested power value for the Mode A pairset in units of 0.1 W.
I32 arubaWiredLldpXdot3RemPDRequestedPowerValueB	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.12	Integer32	read-only	It indicates the PD requested power value for the Mode B pairset in units of 0.1 W.
INT arubaWiredLldpXdot3RemPowerClass	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.6	INTEGER	read-only	The truth value that indicates the requested Class of the PD.
INT arubaWiredLldpXdot3RemPowerClassExt	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.19	INTEGER	read-write	For a single-signature PD or a dual-signature PD connected to a 2-pair only PSE, a read-only value that indicates the currently assigned Class by the remote PSE. For a dual- signature PD connected to a 4-pair capable PSE, a read-only value set to 'dualsig' by the remote PSE. For a PSE connected to a single-signature PD, a read-only value that indicates the requested Class during Physical Layer classification by the remote PD. For a PSE connected to a dual-signature PD, a readonly value set to 'dualsig' by the remote PD.
INT arubaWiredLldpXdot3RemPowerClassExtA	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.17	INTEGER	read-write	For a dual-signature PD, a read-only value that indicates the currently assigned Class for Mode A by the remote 4-pair PSE. For a single-signature PD, or a dual-signature PD connected to a 2-pair only PSE, a read-only value set to 'singlesig' by the remote PSE. For a PSE connected to a dualsignature PD, a read-only value that indicates the requested Class for Mode A during Physical Layer classification by the remote PD. For a PSE connected to a single-signature PD, a read-only value set to 'singlesig' by the remote PD
INT arubaWiredLldpXdot3RemPowerClassExtB	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.18	INTEGER	read-write	For a dual-signature PD, a read-only value that indicates the currently assigned Class for Mode A by the remote 4-pair PSE. For a single-signature PD, or a dual-signature PD connected to a 2-pair only PSE, a read-only value set to 'singlesig' by the remote PSE. For a PSE connected to a dualsignature PD, a read-only value that indicates the requested Class for Mode B during Physical Layer classification by the remote PD. For a PSE connected to a single-signature PD, a read-only value set to 'singlesig' by the remote PD.
INT arubaWiredLldpXdot3RemPowerDownRequest	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.25	INTEGER	read-only	It indicates that the remote PD system is requesting a power down when the value is 0x1D
INT arubaWiredLldpXdot3RemPowerDownTime	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.26	INTEGER	read-only	It indicates the number of seconds the remote PD requests to stay powered off. A value of zero indicates an indefinite amount of time.
arubaWiredLldpXdot3RemPowerEntry	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1		not-accessible	Information about a particular port component.
T/F arubaWiredLldpXdot3RemPowerMDIEnabled	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.3	TruthValue	read-only	The truth value used to indicate whether the MDI power is enabled on given port associated with the remote system.
T/F arubaWiredLldpXdot3RemPowerMDISupported	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.2	TruthValue	read-only	The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system.
T/F arubaWiredLldpXdot3RemPowerPairControlable	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.4	TruthValue	read-only	The truth value used to indicate the ability to control which PSE Pinout Alternative is used for PD detection and power.
INT arubaWiredLldpXdot3RemPowerPairs	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.5	INTEGER	read-only	The truth value that identifies the PSE Pinout Alternative in use for detecting and supplying power to the PD.
INT arubaWiredLldpXdot3RemPowerPortClass	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.1	INTEGER	read-only	The value that identifies the port Class of the given port associated with the remote system.
INT arubaWiredLldpXdot3RemPowerPriority	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.9	INTEGER	read-write	This field reflects the requested remote device power priority. When the power type is PD, this field shall be set to the power priority configured for the device. If a PD is unable to determine its power priority or it has not been configured, then this field shall be set to unknown(1). When the power type is PSE, this field shall be set to unknown(1).
INT arubaWiredLldpXdot3RemPowerSource	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.8	INTEGER	read-only	This field reflects the remote device (PD) requested power source. This field is encoded as pseAndLocal(4) when a PD being powered both locally and by a PSE, to local(3) when the PD being powered locally only, and to pse(2) when the PD is being powered by a PSE
arubaWiredLldpXdot3RemPowerTable	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1		not-accessible	This table contains one row per port of power ethernet information (as a part of the LLDP 802.3bt organizational extension) on the remote system known to this agent.
INT arubaWiredLldpXdot3RemPowerType	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.7	INTEGER	read-only	This field reflects the actual remote power type.
INT arubaWiredLldpXdot3RemPowerTypeExt	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.20	INTEGER	read-only	This field indicates if the remote system is a Type 3 or Type 4 PSE or PD, and in the case of a Type 3 or Type 4 PD, if it is a single-signature PD or dual-signature PD
I32 arubaWiredLldpXdot3RemPSEAllocatedPowerValue	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.13	Integer32	read-only	It indicates the PSE allocated power value received from the remote system. For a PSE, it is the PSE allocated power value that was echoed back by the remote PD, in units of 0.1 W.
I32 arubaWiredLldpXdot3RemPSEAllocatedPowerValueA	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.14	Integer32	read-only	It indicates the PSE allocated power value for the Alternative A pairset received from the remote system. For a PSE, it is the PSE allocated power value for the Alternative A pairset that was echoed back by the remote PD, in units of 0.1 W.
I32 arubaWiredLldpXdot3RemPSEAllocatedPowerValueB	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.15	Integer32	read-only	It indicates the PSE allocated power value for the Alternative B pairset received from the remote system. For a PSE, it is the PSE allocated power value for the Alternative A pairset that was echoed back by the remote PD, in units of 0.1 W.
I32 arubaWiredLldpXdot3RemPSEMaxAvailPower	1.3.6.1.4.1.47196.4.1.1.3.9.1.2.1.1.23	Integer32	read-only	It indicates the remote PSE maximum available power value in units of 0.1 W.
arubaWiredLldpXdot3RemSysGroup	1.3.6.1.4.1.47196.4.1.1.3.9.2.2.2			The collection of objects which are used to represent LLDP 802.3 organizational extension for POEP Remote Device Information. This group is mandatory for agents which implement the LLDP 802.3 organizational extension for POEP.

RFC description

Extends LLDP with IEEE 802.3bt Power over Ethernet information for HPE/Aruba wired network switches.

Start monitoring Aruba (HPE) ArubaOS-CX wired switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ARUBAWIRED-LLDP-MIB

What Is ARUBAWIRED-LLDP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description