All MIBs › ALU-MICROWAVE-MIB
Organization: Nokia
Last Updated: 2008-09-10
Category: Network Interfaces, Vendor: Alcatel-Lucent
Description: Alcatel-Lucent microwave radio link MIB for managing point-to-point microwave system parameters and performance.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ALU-MICROWAVE-MIB?
ALU-MICROWAVE-MIB is a Nokia (formerly Alcatel-Lucent) proprietary MIB for managing point-to-point microwave radio links on the Nokia/ALU 7xxx series transport platform. It exposes link-level configuration such as the radio scheme in use, operational flags, and, notably, alarm state broken down by severity (critical, major, minor, warning). Its primary monitoring value is fault/hardware status of the radio link itself: the alarm state and per-severity alarm counters directly indicate whether a microwave hop is experiencing a signal or hardware fault serious enough to threaten the link. It is a standalone Nokia/ALU proprietary MIB, though it is typically used alongside the vendor's broader network-element and entity MIBs for full node management. It is deployed in telecom backhaul networks that use microwave radio links to connect cell sites or points of presence where fiber isn't available. Engineers can download the ALU-MICROWAVE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ALU-MICROWAVE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia/Alcatel-Lucent 7xxx series microwave radio transport equipment
Monitoring Examples
aluMwLinkTable/aluMwLinkEntry, indexed by aluMwLinkID, exposes aluMwLinkAlarmState along with severity-specific counters aluMwLinkAlarmsCritical, aluMwLinkAlarmsMajor, aluMwLinkAlarmsMinor, and aluMwLinkAlarmsWarning, letting an operator immediately see whether a given microwave hop has active critical alarms consistent with a radio outage. aluMwLinkOperFlags and aluMwLinkRadioScheme show the link's current operational mode and modulation scheme, useful context when diagnosing a degraded link.
What Can Be Monitored
- microwave link alarm state
- critical/major/minor/warning alarm counts
- link operational flags
- radio modulation/scheme in use
This MIB depends on
Related MIBs
Imported Objects
From ALU-SAR-GLOBAL-MIB
| aluSARConfs | OBJECT-IDENTITY |
| aluSARMIBModules | OBJECT-IDENTITY |
| aluSARNotifyPrefix | OBJECT-IDENTITY |
| aluSARObjs | OBJECT-IDENTITY |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
From TIMETRA-CHASSIS-MIB
| tmnxChassisIndex | OBJECT-TYPE |
From TIMETRA-PORT-MIB
| TmnxPortOperStatus |
From TIMETRA-TC-MIB
| TNamedItemOrEmpty | |
| TmnxActionType | |
| TmnxDisplayStringURL | |
| TmnxPortID |
How to Use in IPNetwork Monitor
Example using aluMwLinkAggrFramesTx OID:
Select a Nokia (Alcatel-Lucent) 7xxx-series microwave radio transport equipment as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type aluMwLinkAggrFramesTx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports aluMwLinkAggrFramesTx specifies the number of ethernet frames to be transmitted over radio link. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| aluMwMIBModule | 1.3.6.1.4.1.6527.6.1.1.1.3.6 | This document is the SNMP MIB module to manage and provision the microwave components on the Nokia 7xxx device. Copyright 2012-2014 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| aluMwMIBConformance | 1.3.6.1.4.1.6527.6.1.2.1.7 | |||
| aluMwConformance | 1.3.6.1.4.1.6527.6.1.2.1.7.1 | |||
| aluMwCompliances | 1.3.6.1.4.1.6527.6.1.2.1.7.1.1 | |||
| aluMwComp7705 | 1.3.6.1.4.1.6527.6.1.2.1.7.1.1.1 | |||
| aluMwComp7705V1v0 | 1.3.6.1.4.1.6527.6.1.2.1.7.1.1.1.1 | The compliance statement for revision 1.0 of ALU-MICROWAVE-MIB. | ||
| aluMwGroups | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2 | |||
| aluMwGroup | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2.1 | The group of objects supporting management of the microwave aware ports for the remote management of Microwave Awareness on Nokia SAR series systems. | ||
| aluMwNotificationGroup | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2.2 | The group of notifications supporting the management of microwave awareness on Nokia SAR series systems. | ||
| aluMwNotificationObjsGroup | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2.3 | The group of notifications objs supporting the management of microwave awareness on Nokia SAR series systems. | ||
| aluMwPeerDiscoveryGroup | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2.4 | The group of objects supporting management of the peer discovery management of Microwave Awareness on Nokia SAR series systems. | ||
| aluMwAlarmGroup | 1.3.6.1.4.1.6527.6.1.2.1.7.1.2.5 | The group of objects supporting management of the alarm management of Microwave Awareness on Nokia SAR series systems. | ||
| aluMwObjPrefix | 1.3.6.1.4.1.6527.6.1.2.2.7 | |||
| aluMwObjs | 1.3.6.1.4.1.6527.6.1.2.2.7.1 | |||
| aluMwLinkTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1 | not-accessible | The aluMwLinkTable has an entry for each Packet Microwave Link in the system. | |
| aluMwLinkEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1 | not-accessible | Each row entry represents a Packet Microwave Link that is provisioned on the system. Entries can be created and deleted on the system via SNMP SET operations operations using the aluMwLinkRowStatus object. Creation of this entry enables management of Packet Microwave (MW) Links that contain Microwave Radios. The operational state of the link is based on the state of the contained radios and protection scheme provisioned. | |
| ALU aluMwLinkID | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.1 | AluMwLinkID | not-accessible | aluMwLinkID identifies this Packet Microwave Link. The value of this object is calculated using the TiMOS encoding scheme described in AluMwLinkID. |
| ROW aluMwLinkRowStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.2 | RowStatus | read-create | aluMwLinkRowStatus controls the creation and deletion of row entries in the aluMwLinkTable. The manager has to first calculate the aluMwLinkID based on the TiMOS encoding. |
| BIT aluMwLinkOperFlags | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.3 | Bits | read-only | This object specifies all the conditions that affect the operating status of this Packet Microwave Link. |
| INT aluMwLinkRadioScheme | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.4 | INTEGER | read-create | aluMwLinkRadioScheme specifies the scheme all the radios contained in this link are operating in. |
| INT aluMwLinkAlarmState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.5 | INTEGER | read-only | aluMwLinkAlarmState summarizes the alarm state of the link. A value of 'notSupported' indicates the link does not support alarm management. |
| INT aluMwLinkAlarmsCritical | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.6 | INTEGER | read-only | aluMwLinkAlarmsCritical indicates the number of critical alarms that are raised on this microwave link. |
| INT aluMwLinkAlarmsMajor | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.7 | INTEGER | read-only | aluMwLinkAlarmsMajor indicates the number of major alarms that are raised on this microwave link. |
| INT aluMwLinkAlarmsMinor | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.8 | INTEGER | read-only | aluMwLinkAlarmsMinor indicates the number of minor alarms that are raised on this microwave link. |
| INT aluMwLinkAlarmsWarning | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.9 | INTEGER | read-only | aluMwLinkAlarmsWarning indicates the number of warning alarms that are raised on this microwave link. |
| INT aluMwLinkAlarmsInd | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.10 | INTEGER | read-only | aluMwLinkAlarmsInd indicates the number of indeterminate alarms that are raised on this microwave link. |
| INT aluMwLinkAlarmsCommunication | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.11 | INTEGER | read-only | aluMwLinkAlarmsCommunication indicates the number of alarms related to radio communications that are raised on this microwave link. |
| INT aluMwLinkAlarmsEquipment | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.12 | INTEGER | read-only | aluMwLinkAlarmsEquipment indicates the number of alarms related to equipment that are raised on this microwave link. |
| ALU aluMwLinkEPSActivity | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.13 | AluMwLinkRadioActivity | read-only | aluMwLinkEPSActivity indicates the current activity of the equipment protection scheme |
| ALU aluMwLinkTPSActivity | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.14 | AluMwLinkRadioActivity | read-only | aluMwLinkTPSActivity indicates the current activity of the transport protection scheme |
| ALU aluMwLinkRPSActivity | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.15 | AluMwLinkRadioActivity | read-only | aluMwLinkRPSActivity indicates the current activity of the radio protection scheme |
| ALU aluMwLinkEPSRevertiveness | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.16 | AluMwLinkRevertiveness | read-create | aluMwLinkEPSRevertiveness configures the revertiveness of the equipment protection scheme |
| ALU aluMwLinkTPSRevertiveness | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.17 | AluMwLinkRevertiveness | read-only | aluMwLinkTPSRevertiveness indicates the revertiveness of the transport protection scheme. This is inherited from the aluMwLinkEPSRevertiveness |
| ALU aluMwLinkRPSRevertiveness | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.18 | AluMwLinkRevertiveness | read-create | aluMwLinkRPSRevertiveness configures the revertiveness of the radio protection scheme |
| NUM aluMwLinkEPSMainMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.19 | AluMwLinkMaintenanceOp | read-create | aluMwLinkEPSMainMaintOp applies maintenance operations to the main radio in the equipment protection scheme |
| NUM aluMwLinkEPSSpareMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.20 | AluMwLinkMaintenanceOp | read-create | aluMwLinkEPSSpareMaintOp applies maintenance operations to the spare radio in the equipment protection scheme |
| NUM aluMwLinkTPSMainMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.21 | AluMwLinkMaintenanceOp | read-create | aluMwLinkTPSMainMaintOp applies maintenance operations to the main radio in the transport protection scheme |
| NUM aluMwLinkTPSSpareMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.22 | AluMwLinkMaintenanceOp | read-create | aluMwLinkTPSSpareMaintOp applies maintenance operations to the spare radio in the transport protection scheme |
| NUM aluMwLinkRPSMainMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.23 | AluMwLinkMaintenanceOp | read-create | aluMwLinkRPSMainMaintOp applies maintenance operations to the main radio in the radio protection scheme |
| NUM aluMwLinkRPSSpareMaintOp | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.24 | AluMwLinkMaintenanceOp | read-create | aluMwLinkRPSSpareMaintOp applies maintenance operations to the spare radio in the radio protection scheme |
| ALU aluMwLinkPeerID | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.25 | AluMwLinkID | read-only | aluMwLinkPeerID identifies the peer Microwave Link. The value of this object is calculated using the TiMOS encoding scheme described in AluMwLinkID when connected to 7705 SAR systems and based on peer encoding scheme for other peer types. |
| IP aluMwLinkPeerNEIpAddress | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.26 | IpAddress | read-only | aluMwLinkPeerNEIpAddress identifies the peer NE IPv4 address. |
| TMN aluMwLinkClearStatistics | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.27 | TmnxActionType | read-create | aluMwLinkClearStatistics clears all link level statistics. |
| T/F aluMwLinkPeerDiscovery | 1.3.6.1.4.1.6527.6.1.2.2.7.1.1.1.28 | TruthValue | read-create | aluMwLinkPeerDiscovery enables and disables discovery of peer information on managed microwave links. The value of aluMwLinkPeerDiscovery is not used for standalone microwave links. |
| aluMwRadioTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2 | not-accessible | The aluMwRadioTable has an entry for each Microwave Radio in the system. | |
| aluMwRadioEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1 | not-accessible | Each row entry represents a Microwave Radio that is connected off a physical port on the system. The aluMwRadioPortID contains this port encoded in it. Entries can be created and deleted on microwave-aware ports via SNMP SET operations using the aluMwRadioRowStatus object. Creation of this entry enables management of connected Microwave (MW) Packet Transport Radios. The operational state of the connected radio and it's Microwave Link is represented in the operational state of this entry. Microwave Radios may only be created on ports that support microwave-awareness. There can be only one Microwave Radio on each port. | |
| TMN aluMwRadioPortID | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.1 | TmnxPortID | not-accessible | aluMwRadioPortID identifies the port of this microwave radio. The value of this object is calculated using the TiMOS encoding scheme described in TmnxPortID. |
| ROW aluMwRadioRowStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.2 | RowStatus | read-create | aluMwRadioRowStatus controls the creation and deletion of row entries in the aluMwRadioTable. The manager has to first calculate the aluMwRadioPortID based on the TiMOS encoding. Setting aluMwRadioRowStatus to 'createAndGo(4)', 'createAndWait(5)' or 'destroy(6)' will be rejected if aluMwRadioPortID is set to a TmnxPortID that is the same as either TIMETRA-CHASSIS-MIB::tmnxSyncIfTimingRef1SrcPort or TIMETRA-CHASSIS-MIB::tmnxSyncIfTimingRef2SrcPort. |
| INT aluMwRadioMode | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.3 | INTEGER | read-create | aluMwRadioMode specifies the role this microwave radio is operating with respect to the 'mw-link' that it is part of. This radio will be a 'main (1)' or 'spare (2)' radio in an mw-link. This object can only be set with aluMwRadioRowStatus during the creation of the mw-link. |
| ALU aluMwRadioMwLinkID | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.4 | AluMwLinkID | read-create | aluMwRadioMwLinkID indicates the AluMwLinkID of the mw-link that this radio is part of. This object must be set during conjunction with aluMwRadioRowStatus during mw-link creation. |
| TMN aluMwRadioOperStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.5 | TmnxPortOperStatus | read-only | The current operational status of this microwave radio. |
| BIT aluMwRadioOperFlags | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.6 | Bits | read-only | This object specifies all the conditions that affect the operating status of this radio. Only 'portOperDown' is applicable to radios operating as standalone devices as indicated by aluMwRadioStandalone. |
| T/F aluMwRadioStandalone | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.7 | TruthValue | read-create | This object specifies whether the radio is operating as a standalone network element or if it is managed by this router. A value of 'true' indicates it is operating as a standalone device. |
| TNA aluMwRadioName | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.8 | TNamedItemOrEmpty | read-create | The textual name of the radio. |
| TNA aluMwRadioDatabaseFilename | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.9 | TNamedItemOrEmpty | read-create | aluMwRadioDatabaseFilename specifies the filename of the radio's database. This file must be located at the same path as the system configuration file. |
| INT aluMwRadioType | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.10 | INTEGER | read-only | aluMwRadioType specifies the device type of microwave radio. The type of radio is only available when the microwave radio is managed and is present. aluMwRadioType returns a value of '0' when the radio type is unknown. |
| INT aluMwRadioFrequency | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.11 | INTEGER | read-only | aluMwRadioType specifies the frequency of the microwave radio. The frequency of the radio is only available when the microwave radio is managed and is present. |
| INT aluMwRadioAlarmState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.12 | INTEGER | read-only | aluMwRadioAlarmState summarizes the alarm state of the radio. |
| INT aluMwRadioAlarmsCritical | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.13 | INTEGER | read-only | aluMwRadioAlarmsCritical indicates the number of critical alarms that are raised on this microwave radio. |
| INT aluMwRadioAlarmsMajor | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.14 | INTEGER | read-only | aluMwRadioAlarmsMajor indicates the number of major alarms that are raised on this microwave radio. |
| INT aluMwRadioAlarmsMinor | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.15 | INTEGER | read-only | aluMwRadioAlarmsMinor indicates the number of minor alarms that are raised on this microwave radio. |
| INT aluMwRadioAlarmsWarning | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.16 | INTEGER | read-only | aluMwRadioAlarmsWarning indicates the number of warning alarms that are raised on this microwave radio. |
| INT aluMwRadioAlarmsInd | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.17 | INTEGER | read-only | aluMwRadioAlarmsInd indicates the number of indeterminate alarms that are raised on this microwave radio. |
| INT aluMwRadioAlarmsCommunication | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.18 | INTEGER | read-only | aluMwRadioAlarmsCommunication indicates the number of alarms related to radio communications that are raised on this microwave radio. |
| INT aluMwRadioAlarmsEquipment | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.19 | INTEGER | read-only | aluMwRadioAlarmsEquipment indicates the number of alarms related to equipment that are raised on this microwave radio. |
| INT aluMwRadioTxMuted | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.20 | INTEGER | read-create | aluMwRadioTxMuted indicates the current state of the transmitter. |
| TMN aluMwRadioReboot | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.21 | TmnxActionType | read-create | aluMwRadioReboot performs a reset of the radio device. |
| TIM aluMwRadioLastStateChange | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.22 | TimeStamp | read-only | The aluMwRadioLastStateChange variable contains the value of the sysUpTime the last time the operational status of the radio link changed state. |
| TIM aluMwRadioCommEstablished | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.23 | TimeStamp | read-only | The aluMwRadioCommEstablished variable contains the value of the sysUpTime the last time the radio managment communications was established. |
| TIM aluMwRadioCommLost | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.24 | TimeStamp | read-only | The aluMwRadioCommLost variable contains the value of the sysUpTime the last time the radio managment communications was lost. |
| ALU aluMwRadioSwState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.25 | AluMwRadioSwState | read-only | aluMwRadioSwState indicates the state of software on the MPT. |
| INT aluMwRadioSwDnldProgress | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.26 | INTEGER | read-only | aluMwRadioSwDnldProgress indicates the progress percentage of an in-progress software download to the MPT. |
| STR aluMwRadioRslHistoryUrl | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.27 | TmnxDisplayStringURL | read-create | aluMwRadioRslHistoryUrl specifies the URL of the radio's RSL history. This file must be located on the local compact flash. |
| TMN aluMwRadioRslHistoryClear | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.28 | TmnxActionType | read-create | aluMwRadioRslHistoryClear performs a clear of the MPT RSL history. |
| BIT aluMwRadioFfdSuppressFlags | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.29 | Bits | read-create | This object specifies the MPT radio fault conditions which can be suppressed. |
| T/F aluMwRadioPMG826Enable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.30 | TruthValue | read-create | This object enables normalized G.826 performance monitoring statistics to be collected. |
| T/F aluMwRadioPMG826OperStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.31 | TruthValue | read-only | The current operational status of normalized G.826 performance monitoring statistics. |
| TMN aluMwRadioPMG826Clear | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.32 | TmnxActionType | read-create | Clears the recorded current and historical normalized G.826 statistics. |
| T/F aluMwRadioPMACMEnable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.33 | TruthValue | read-create | This object enables Adaptive Coding and Modulation performance monitoring statistics to be collected. |
| T/F aluMwRadioPMACMOperStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.34 | TruthValue | read-only | The current operational status of Adaptive Coding and Modulation performance monitoring statistics. |
| TMN aluMwRadioPMACMClear | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.35 | TmnxActionType | read-create | Clears the recorded current and historical Adaptive Coding and Modulation statistics. |
| T/F aluMwRadioPMPowerEnable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.36 | TruthValue | read-create | This object enables RX and TX power performance monitoring statistics to be collected. |
| T/F aluMwRadioPMPowerOperStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.37 | TruthValue | read-only | The current operational status of RX and TX power performance monitoring statistics. |
| TMN aluMwRadioPMPowerClear | 1.3.6.1.4.1.6527.6.1.2.2.7.1.2.1.38 | TmnxActionType | read-create | Clears the recorded current and historical RX and TX power statistics. |
| aluMwRadioPowerMeasuresTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3 | not-accessible | This table contains the radio analogue measurements. | |
| aluMwRadioPowerMeasuresEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1 | not-accessible | An entry of the analogue measurements table. Each entry corresponds to a Radio Synchronous or Plesiochronous Physical Interface (RSPI or RPPI). | |
| I32 aluMwRadioLocalTxPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.1 | Integer32 | read-only | This object represents the local transmitted power level. It is an integer with associated measure unit expressed in decade of dBm. |
| I32 aluMwRadioLocalRxMainPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.2 | Integer32 | read-only | This object represents the local received power level. In case of space diversity configuration with combiner function in base band it is used to represent the power at the input of the local main receiver. It is a negative integer with associated measure unit expressed in decade of dBm. |
| I32 aluMwRadioRemoteTxPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.3 | Integer32 | read-only | This object represents the remote transmitted power level. It is an integer with associated measure unit expressed in decade of dBm. |
| I32 aluMwRadioRemoteRxMainPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.4 | Integer32 | read-only | This object represents the remote received power level. In case of space diversity configuration with combiner function in base band it is used to represent the power at the input of the remote main receiver. It is a negative integer with associated measure unit expressed in decade of dBm. |
| I32 aluMwRadioLocalDiversityPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.5 | Integer32 | read-only | This object represents the local RSL power for SD (combiner) module input. It is an integer with associated measure unit expressed in decade of dBm. |
| I32 aluMwRadioRemoteDiversityPower | 1.3.6.1.4.1.6527.6.1.2.2.7.1.3.1.6 | Integer32 | read-only | This object represents the remote RSL power for SD (combiner) module input. It is a negative integer with associated measure unit expressed in decade of dBm. |
| aluMwRadioAlarmsTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4 | not-accessible | This table contains the radio alarm conditions. | |
| aluMwRadioAlarmsEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1 | not-accessible | An entry of the alarms table. Each entry corresponds to a Radio alarm conditions that is currently raised or cleared. | |
| INT aluMwRadioAlarmID | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.1 | INTEGER | not-accessible | Used by Microwave notifications, the OID indicates the identifier of an alarm condition on the radio device. |
| DAT aluMwRadioAlarmTime | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.2 | DateAndTime | read-only | Used by Microwave notifications, the OID indicates the time at which the event occured on the radio device. |
| STR aluMwRadioAlarmName | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.3 | DisplayString | read-only | This object contains the alarm name of the condition. |
| INT aluMwRadioAlarmSeverity | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.4 | INTEGER | read-only | Used by Microwave notifications, the OID indicates the severity of an alarm condition on the radio device. |
| STR aluMwRadioAlarmSpecProblem | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.5 | DisplayString | read-only | This object contains the alarm specific problem description. Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by characters. The format of the DisplayString is defined as follow: String | OID | ({String;}((OID | Integer);)*) |
| INT aluMwRadioAlarmType | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.6 | INTEGER | read-only | Used by Microwave notifications, the OID indicates the type of alarm condition on the radio device. |
| STR aluMwRadioAlarmObject | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.7 | DisplayString | read-only | Used by Microwave notifications, the OID indicates the object on the radio device that has the alarm condition. |
| STR aluMwRadioAlarmSubObject | 1.3.6.1.4.1.6527.6.1.2.2.7.1.4.1.8 | DisplayString | read-only | Used by Microwave notifications, the OID indicates the sub-object on the radio device that has the alarm condition. |
| aluMwLinkStatisticsTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5 | not-accessible | The aluMwLinkStatisticsTable has an entry for each Packet Microwave Link in the system. | |
| aluMwLinkStatisticsEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1 | not-accessible | Each row entry represents a Packet Microwave Link that is provisioned on the system. | |
| C64 aluMwLinkAggrFramesTxEx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.1 | Counter64 | read-only | aluMwLinkAggrFramesTx specifies the number of ethernet frames to be transmitted over radio link. |
| C64 aluMwLinkAggrOctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.2 | Counter64 | read-only | aluMwLinkAggrOctetsTx specifies the number of octets to be transmitted over radio link. |
| C64 aluMwLinkAggrDiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.3 | Counter64 | read-only | aluMwLinkAggrDiscardedTx specifies the number of frames discarded on the radio before transmission. |
| C64 aluMwLinkQueue1FramesTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.4 | Counter64 | read-only | aluMwLinkQueue1FramesTx specifies the number of ethernet frames to be transmitted from queue 1 over radio link. |
| C64 aluMwLinkQueue1OctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.5 | Counter64 | read-only | aluMwLinkQueue1OctetsTx specifies the number of octets to be transmitted from queue 1 over radio link. |
| C64 aluMwLinkQueue1DiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.6 | Counter64 | read-only | aluMwLinkQueue1DiscardedTx specifies the number of frames discarded on the radio from queue 1 before transmission. |
| C64 aluMwLinkQueue2FramesTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.7 | Counter64 | read-only | aluMwLinkQueue2FramesTx specifies the number of ethernet frames to be transmitted from queue 2 over radio link. |
| C64 aluMwLinkQueue2OctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.8 | Counter64 | read-only | aluMwLinkQueue2OctetsTx specifies the number of octets transmitted to be from queue 2 over radio link. |
| C64 aluMwLinkQueue2DiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.9 | Counter64 | read-only | aluMwLinkQueue2DiscardedTx specifies the number of frames discarded on the radio from queue 2 before transmission. |
| C64 aluMwLinkQueue3FramesTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.10 | Counter64 | read-only | aluMwLinkQueue3FramesTx specifies the number of ethernet frames to be transmitted from queue 3 over radio link. |
| C64 aluMwLinkQueue3OctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.11 | Counter64 | read-only | aluMwLinkQueue3OctetsTx specifies the number of octets to be transmitted from queue 3 over radio link. |
| C64 aluMwLinkQueue3DiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.12 | Counter64 | read-only | aluMwLinkQueue3DiscardedTx specifies the number of frames discarded on the radio from queue 3 before transmission. |
| C64 aluMwLinkQueue4FramesTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.13 | Counter64 | read-only | aluMwLinkQueue4FramesTx specifies the number of ethernet frames to be transmitted from queue 4 over radio link. |
| C64 aluMwLinkQueue4OctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.14 | Counter64 | read-only | aluMwLinkQueue4OctetsTx specifies the number of octets to be transmitted from queue 4 over radio link. |
| C64 aluMwLinkQueue4DiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.15 | Counter64 | read-only | aluMwLinkQueue4DiscardedTx specifies the number of frames discarded on the radio from queue 4 before transmission. |
| C64 aluMwLinkQueue5FramesTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.16 | Counter64 | read-only | aluMwLinkQueue5FramesTx specifies the number of ethernet frames to be transmitted from queue 5 over radio link. |
| C64 aluMwLinkQueue5OctetsTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.17 | Counter64 | read-only | aluMwLinkQueue5OctetsTx specifies the number of octets to be transmitted from queue 5 over radio link. |
| C64 aluMwLinkQueue5DiscardedTx | 1.3.6.1.4.1.6527.6.1.2.2.7.1.5.1.18 | Counter64 | read-only | aluMwLinkQueue5DiscardedTx specifies the number of frames discarded on the radio from queue 5 before transmission. |
| aluMwRadioInfoTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6 | not-accessible | The aluMwRadioInfoTable has an entry for each Microwave Radio in the system. | |
| aluMwRadioInfoEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1 | not-accessible | Each row entry represents a Microwave Radio that is connected off a physical port on the system. The aluMwRadioPortID contains this port encoded in it. | |
| T/F aluMwRadioInfoValid | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.1 | TruthValue | read-only | aluMwRadioInfoValid indicates whether the info of the MPT is valid. |
| STR aluMwRadioCompanyId | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.2 | SnmpAdminString | read-only | The inventory company identifier for the microwave radio. |
| STR aluMwRadioMnemonic | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.3 | SnmpAdminString | read-only | The mnemonic inventory value for the microwave radio. |
| STR aluMwRadioCLEI | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.4 | SnmpAdminString | read-only | The inventory CLEI value for the microwave radio. |
| STR aluMwRadioHwPartNumber | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.5 | SnmpAdminString | read-only | The inventory Hardware Part + ICS value for the microwave radio. |
| STR aluMwRadioSwPartNumber | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.6 | SnmpAdminString | read-only | The inventory Software Part number for the microwave radio. |
| STR aluMwRadioFactoryId | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.7 | SnmpAdminString | read-only | The inventory factory identifier for the microwave radio. |
| STR aluMwRadioSerialNumber | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.8 | SnmpAdminString | read-only | The unique inventory serial number for the microwave radio. |
| STR aluMwRadioMfgDateId | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.9 | SnmpAdminString | read-only | The inventory manufacturing date identifier for the microwave radio. |
| STR aluMwRadioMfgDate | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.10 | SnmpAdminString | read-only | The inventory manufacturing date for the microwave radio. |
| STR aluMwRadioCustomerField | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.11 | SnmpAdminString | read-only | The inventory customer field for the microwave radio. |
| INT aluMwRadioTemperature | 1.3.6.1.4.1.6527.6.1.2.2.7.1.6.1.12 | INTEGER | read-only | aluMwRadioTemperature indicates the temperature of the MPT. |
| aluMwTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.7 | not-accessible | The aluMwTable has system information for microwave. | |
| aluMwEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.7.1 | not-accessible | Each row entry represents a Microwave System. | |
| T/F aluMwSwPackageValid | 1.3.6.1.4.1.6527.6.1.2.2.7.1.7.1.1 | TruthValue | read-only | aluMwSwPackageValid indicates whether SAR has detected a valid Software package for managed radios. |
| INT aluMwSwDownloadTool | 1.3.6.1.4.1.6527.6.1.2.2.7.1.7.1.2 | INTEGER | read-write | aluMwSwDownloadTool is used to initiate a software download of radio software to all managed radios. |
| INT aluMwSwDownloadState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.7.1.3 | INTEGER | read-only | aluMwSwDownloadState is used to indicate the state of the of radio software to all managed radios. noSoftwarePackage - No Valid Software Package Found ready - Software is Ready downloadInProgress - Software Tool Download downloadFailed - Software Tool Failed |
| aluMwLinkTdaStatusTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.8 | not-accessible | This table contains the MW link Transmit Diversity Antenna status. | |
| aluMwLinkTdaStatusEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.8.1 | not-accessible | An entry of the Transmit Diversity Antenna status table. | |
| INT aluMwLinkTdaCmdState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.8.1.1 | INTEGER | read-only | aluMwLinkTdaCmdState is used to get the TDA command state. |
| INT aluMwLinkTdaManualCmdStatus | 1.3.6.1.4.1.6527.6.1.2.2.7.1.8.1.2 | INTEGER | read-only | aluMwLinkTdaManualCmdStatus is used to get the TDA manual command status. |
| INT aluMwLinkTdaSwitchPosition | 1.3.6.1.4.1.6527.6.1.2.2.7.1.8.1.3 | INTEGER | read-only | aluMwLinkTdaSwitchPosition is used to get the TDA switch position. |
| aluMwRadioPMG826Table | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9 | not-accessible | This table contains the current and historic normalized G.826 performance monitoring statistics for the given radio. | |
| aluMwRadioPMG826Entry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1 | not-accessible | An entry of the microwave radio G.826 performance monitoring table. | |
| ALU aluMwPMG826Section | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.1 | AluMwPerfMonSection | read-only | Index to select the radio link or radio hop. |
| ALU aluMwPMG826Period | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.2 | AluMwPerfMonPeriod | read-only | Index to select the 15 minute or 24 hour counters. |
| ALU aluMwPMG826Bin | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.3 | AluMwPerfMonBin | read-only | Index to select the current (0) or historic counters. |
| INT aluMwPMG826Date | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.4 | INTEGER | read-only | The number of seconds since midnight, January 1st 1970 to the start of this counting period (even 15 minutes or beginning of day, depending on selected period). |
| INT aluMwPMG826Duration | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.5 | INTEGER | read-only | The number of seconds recorded in this period. |
| ALU aluMwPMG826EPSState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.6 | AluMwPerfMonEPSState | read-only | The EPS state at the time of recording this period. |
| T/F aluMwPMG826Suspect | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.7 | TruthValue | read-only | If the stats are incomplete for this period, they will be considered suspect. |
| U32 aluMwPMG826ES | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.8 | Unsigned32 | read-only | The number of errored seconds. |
| U32 aluMwPMG826SES | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.9 | Unsigned32 | read-only | The number severely errored seconds. |
| U32 aluMwPMG826BBE | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.10 | Unsigned32 | read-only | The number of background block errors. |
| U32 aluMwPMG826UAS | 1.3.6.1.4.1.6527.6.1.2.2.7.1.9.1.11 | Unsigned32 | read-only | The number of unavailable seconds. |
| aluMwRadioPMACMTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10 | not-accessible | This table contains the current and historic adaptive coding and modulation performance monitoring statistics for the given radio. | |
| aluMwRadioPMACMEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1 | not-accessible | An entry of the microwave ACM performance monitoring table. | |
| ALU aluMwPMACMPeriod | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.1 | AluMwPerfMonPeriod | read-only | Index to select the 15 minute or 24 hour counters. |
| ALU aluMwPMACMBin | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.2 | AluMwPerfMonBin | read-only | Index to select the current (0) or historic counters. |
| INT aluMwPMACMModulation | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.3 | INTEGER | read-only | Index to select the modulation ID. |
| INT aluMwPMACMDate | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.4 | INTEGER | read-only | The number of seconds since midnight, January 1st 1970 to the start of this counting period (even 15 minutes or beginning of day, depending on selected period). |
| INT aluMwPMACMDuration | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.5 | INTEGER | read-only | The number of seconds recorded in this period. |
| T/F aluMwPMACMSuspect | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.6 | TruthValue | read-only | If the stats are incomplete for this period, they will be considered suspect. |
| U32 aluMwPMACMTimeSpent | 1.3.6.1.4.1.6527.6.1.2.2.7.1.10.1.7 | Unsigned32 | read-only | The number of milliseconds spent at this modulation. |
| aluMwRadioPMPowerTable | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11 | not-accessible | This table contains the current and historic RX and TX power performance monitoring statistics for the given radio. | |
| aluMwRadioPMPowerEntry | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1 | not-accessible | An entry of the microwave Power performance monitoring table. | |
| INT aluMwPMPowerDirection | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.1 | INTEGER | read-only | Index to select the received or transmitted power levels. |
| ALU aluMwPMPowerSection | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.2 | AluMwPerfMonSection | read-only | Index to select the radio link or radio hop. Radio link is not applicable when the direction is tx. |
| ALU aluMwPMPowerPeriod | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.3 | AluMwPerfMonPeriod | read-only | Index to select the 15 minute or 24 hour counters. |
| ALU aluMwPMPowerBin | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.4 | AluMwPerfMonBin | read-only | Index to select the current (0) or historic counters. |
| INT aluMwPMPowerDate | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.5 | INTEGER | read-only | The number of seconds since midnight, January 1st 1970 to the start of this counting period (even 15 minutes or beginning of day, depending on selected period). |
| INT aluMwPMPowerDuration | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.6 | INTEGER | read-only | The number of seconds recorded in this period. |
| ALU aluMwPMPowerEPSState | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.7 | AluMwPerfMonEPSState | read-only | The EPS state at the time of recording this period. If the direction is tx, EPS state is always notRelevant. |
| T/F aluMwPMPowerSuspect | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.8 | TruthValue | read-only | If the stats are incomplete for this period, they will be considered suspect. |
| I32 aluMwPMPowerMinPowerLevel | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.9 | Integer32 | read-only | The minimum power level. |
| I32 aluMwPMPowerMaxPowerLevel | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.10 | Integer32 | read-only | The maximum power level. |
| I32 aluMwPMPowerMeanPowerLevel | 1.3.6.1.4.1.6527.6.1.2.2.7.1.11.1.11 | Integer32 | read-only | The average power level. |
| aluMwNotifyObjs | 1.3.6.1.4.1.6527.6.1.2.2.7.2 | |||
| TMN aluMwNotifyRadioPortID | 1.3.6.1.4.1.6527.6.1.2.2.7.2.1 | TmnxPortID | accessible-for-notify | Used by Microwave notifications, the OID indicates the port id where a radio is connected. |
| DAT aluMwNotifyAlarmTime | 1.3.6.1.4.1.6527.6.1.2.2.7.2.2 | DateAndTime | accessible-for-notify | Used by Microwave notifications, the OID indicates the time at which the event occured on the radio device. |
| INT aluMwNotifyAlarmId | 1.3.6.1.4.1.6527.6.1.2.2.7.2.3 | INTEGER | accessible-for-notify | Used by Microwave notifications, the OID indicates the identifier of an alarm condition on the radio device. |
| STR aluMwNotifyAlarmName | 1.3.6.1.4.1.6527.6.1.2.2.7.2.4 | DisplayString | accessible-for-notify | This object contains the alarm name of the condition. |
| STR aluMwNotifyAlarmSpecProblem | 1.3.6.1.4.1.6527.6.1.2.2.7.2.5 | DisplayString | accessible-for-notify | This object contains the alarm specific problem description. Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by characters. The format of the DisplayString is defined as follow: String | OID | ({String;}((OID | Integer);)*) |
| INT aluMwNotifyAlarmType | 1.3.6.1.4.1.6527.6.1.2.2.7.2.6 | INTEGER | accessible-for-notify | Used by Microwave notifications, the OID indicates the type of alarm condition on the radio device. |
| STR aluMwNotifyAlarmObject | 1.3.6.1.4.1.6527.6.1.2.2.7.2.7 | DisplayString | accessible-for-notify | Used by Microwave notifications, the OID indicates the object on the radio device that has the alarm condition. |
| STR aluMwNotifyAlarmSubObject | 1.3.6.1.4.1.6527.6.1.2.2.7.2.8 | DisplayString | accessible-for-notify | Used by Microwave notifications, the OID indicates the sub-object on the radio device that has the alarm condition. |
| INT aluMwNotifyTxMute | 1.3.6.1.4.1.6527.6.1.2.2.7.2.9 | INTEGER | accessible-for-notify | Used by Microwave notifications, the OID indicates the type of mute on the radio transmitter. |
| TMN aluMwNotifyLinkPortID | 1.3.6.1.4.1.6527.6.1.2.2.7.2.10 | TmnxPortID | accessible-for-notify | Used by Microwave notifications, the OID indicates the port id where a microwave link. |
| INT aluMwNotifyLinkActivity | 1.3.6.1.4.1.6527.6.1.2.2.7.2.11 | INTEGER | accessible-for-notify | Used by Microwave notifications, the OID indicates the the activity of the link of a protection scheme. |
| INT aluMwNotifyLinkProtectionType | 1.3.6.1.4.1.6527.6.1.2.2.7.2.12 | INTEGER | accessible-for-notify | Used by Microwave notifications, the OID indicates the the type of protection. |
| ALU aluMwNotifyRadioSwState | 1.3.6.1.4.1.6527.6.1.2.2.7.2.13 | AluMwRadioSwState | accessible-for-notify | Used by Microwave notifications, the OID indicates the the state of radio software. |
| aluMwNotifyPrefix | 1.3.6.1.4.1.6527.6.1.2.3.10 | |||
| aluMwNotification | 1.3.6.1.4.1.6527.6.1.2.3.10.0 | |||
| NTF aluMwRadioLinkUp | 1.3.6.1.4.1.6527.6.1.2.3.10.0.1 | Generated when a microwave radio link goes up. | ||
| NTF aluMwRadioLinkDown | 1.3.6.1.4.1.6527.6.1.2.3.10.0.2 | Generated when a microwave radio link goes down. | ||
| NTF aluMwRadioPresent | 1.3.6.1.4.1.6527.6.1.2.3.10.0.3 | Generated when a microwave radio device is detected. | ||
| NTF aluMwRadioNotPresent | 1.3.6.1.4.1.6527.6.1.2.3.10.0.4 | Generated when a microwave radio device is no longer detected. | ||
| NTF aluMwRadioSwPackageMissing | 1.3.6.1.4.1.6527.6.1.2.3.10.0.5 | Generated when a valid microwave radio software package is not present at startup. | ||
| NTF aluMwRadioDatabaseUpdated | 1.3.6.1.4.1.6527.6.1.2.3.10.0.6 | Generated when a microwave radio database has been updated. | ||
| NTF aluMwRadioCriticalAlarmRaise | 1.3.6.1.4.1.6527.6.1.2.3.10.0.7 | This notification reports the critical radio defect raise. | ||
| NTF aluMwRadioCriticalAlarmClear | 1.3.6.1.4.1.6527.6.1.2.3.10.0.8 | This notification reports critical defect radio clear. | ||
| NTF aluMwRadioMajorAlarmRaise | 1.3.6.1.4.1.6527.6.1.2.3.10.0.9 | This notification reports the major radio defect raise. | ||
| NTF aluMwRadioMajorAlarmClear | 1.3.6.1.4.1.6527.6.1.2.3.10.0.10 | This notification reports major defect radio clear. | ||
| NTF aluMwRadioMinorAlarmRaise | 1.3.6.1.4.1.6527.6.1.2.3.10.0.11 | This notification reports the minor radio defect raise. | ||
| NTF aluMwRadioMinorAlarmClear | 1.3.6.1.4.1.6527.6.1.2.3.10.0.12 | This notification reports minor defect radio clear. | ||
| NTF aluMwRadioWarningAlarmRaise | 1.3.6.1.4.1.6527.6.1.2.3.10.0.13 | This notification reports the warning radio defect raise. | ||
| NTF aluMwRadioWarningAlarmClear | 1.3.6.1.4.1.6527.6.1.2.3.10.0.14 | This notification reports warning defect radio clear. | ||
| NTF aluMwRadioIndetermAlarmRaise | 1.3.6.1.4.1.6527.6.1.2.3.10.0.15 | This notification reports the indeterminate radio defect raise. | ||
| NTF aluMwRadioIndetermAlarmClear | 1.3.6.1.4.1.6527.6.1.2.3.10.0.16 | This notification reports indeterminate defect radio clear. | ||
| NTF aluMwRadioTxChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.17 | Generated when a microwave radio transmitter changes state. | ||
| NTF aluMwLinkEPSActivityChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.18 | Generated when a microwave link changes activity for EPS. | ||
| NTF aluMwLinkTPSActivityChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.19 | Generated when a microwave link changes activity for TPS. | ||
| NTF aluMwLinkRPSActivityChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.20 | Generated when a microwave link changes activity for RPS. | ||
| NTF aluMwLinkMaintenanceChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.21 | Generated when a microwave link maintenance command changes. | ||
| NTF aluMwLinkPeerChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.22 | Generated when a microwave link discovered peer changes. | ||
| NTF aluMwRadioSwStateChange | 1.3.6.1.4.1.6527.6.1.2.3.10.0.23 | Generated when on microwave radio software state changes. | ||
| NTF aluMwRadioRslHistoryUploadFail | 1.3.6.1.4.1.6527.6.1.2.3.10.0.24 | Generated when microwave radio RSL History upload fails. | ||
| NTF aluMwMptSwReconcileFail | 1.3.6.1.4.1.6527.6.1.2.3.10.0.25 | Generated when microwave MPT sw reconcile fails. | ||
| NTF aluMwRadioRslHistoryCleared | 1.3.6.1.4.1.6527.6.1.2.3.10.0.26 | Generated when microwave radio RSL History is cleared. | ||
| NTF aluMwRadioPMG826OperUp | 1.3.6.1.4.1.6527.6.1.2.3.10.0.27 | Generated when microwave radio G826 PM becomes operationally up. | ||
| NTF aluMwRadioPMG826OperDown | 1.3.6.1.4.1.6527.6.1.2.3.10.0.28 | Generated when microwave radio G826 PM becomes operationally down. | ||
| NTF aluMwRadioPMACMOperUp | 1.3.6.1.4.1.6527.6.1.2.3.10.0.29 | Generated when microwave radio ACM PM becomes operationally up. | ||
| NTF aluMwRadioPMACMOperDown | 1.3.6.1.4.1.6527.6.1.2.3.10.0.30 | Generated when microwave radio ACM PM becomes operationally down. | ||
| NTF aluMwRadioPMPowerOperUp | 1.3.6.1.4.1.6527.6.1.2.3.10.0.31 | Generated when microwave radio power PM becomes operationally up. | ||
| NTF aluMwRadioPMPowerOperDown | 1.3.6.1.4.1.6527.6.1.2.3.10.0.32 | Generated when microwave radio power PM becomes operationally down. |
RFC description
Microwave components management and provisioning for Nokia 7xxx devices.
Start monitoring Nokia (Alcatel-Lucent) 7xxx-series microwave radio transport equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.