ALCATEL-IND1-IPX-MIB

All MIBs › ALCATEL-IND1-IPX-MIB

Organization: Alcatel-Lucent

Last Updated: 2007-04-03

Category: IP and Core Protocols, Vendor: Alcatel-Lucent

Description: Alcatel OmniSwitch IPX routing MIB for managing Novell IPX network addresses, routes, and SAP services.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-IPX-MIB?

ALCATEL-IND1-IPX-MIB is a legacy Alcatel proprietary OmniSwitch MIB for managing the Novell IPX routing subsystem, including static and default route configuration on the switch. It exposes tables for statically configured IPX routes (network number, next-hop network/node, tick/hop-count metrics) and default IPX routes per VLAN, with RowStatus-controlled provisioning. Its monitoring value is configuration-state visibility into the legacy IPX routing table — confirming static/default routes are correctly provisioned with expected next hops and metrics — rather than hardware health, reflecting its role supporting now-largely-obsolete Novell NetWare networking. It is a self-contained legacy protocol MIB with no significant dependency on other MIBs beyond Alcatel's own enterprise conventions. It's deployed only on older Alcatel OmniSwitch installations still supporting legacy IPX/NetWare traffic, which is uncommon in modern networks, though administrators can still download the ALCATEL-IND1-IPX-MIB file to load into their MIB browser when needed.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-IPX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel/Alcatel-Lucent OmniSwitch (legacy IPX/NetWare routing configurations)

Monitoring Examples

An administrator maintaining a legacy IPX network would poll alaIpxStaticRouteTable, indexed by alaIpxStaticRouteNetNum, to confirm alaIpxStaticRouteNextHopNet/Node and alaIpxStaticRouteTicks/HopCount match the intended static route configuration. alaIpxDefRouteTable, indexed by alaIpxDefRouteVlanId, shows the default IPX route configured per VLAN, checked when IPX clients on that VLAN can't reach non-local IPX networks. A missing or RowStatus-inactive entry in either table typically explains an IPX connectivity failure between segments.

What Can Be Monitored

static IPX route configuration
default IPX route per VLAN
IPX route next-hop and metric
route row status/provisioning state

Imported Objects

From ALCATEL-IND1-BASE

routingIND1Ipx

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
alcatelIND1IPXMIB	1.3.6.1.4.1.6486.801.1.2.1.10.8.1			This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This is the proprietary MIB for the IPX routing sub-sytem. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
alcatelIND1IPXMIBObjects	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1
alaIpxRoutingGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1			IPX routing information.
alaIpxStaticRouteTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1		not-accessible	The Static Routes table is used and add entries and extract information from the static routes configured in the system.
alaIpxStaticRouteEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1		not-accessible	Each entry corresponds to one static route.
NET alaIpxStaticRouteNetNum	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.1	NetNumber	not-accessible	The IPX network number of the route's destination.
NET alaIpxStaticRouteNextHopNet	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.2	NetNumber	read-create	The IPX network number of the router used to reach the first hop in the static route.
ADR alaIpxStaticRouteNextHopNode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.3	HostAddress	read-create	The IPX node number of the router used to reach the first hop in the static route.
INT alaIpxStaticRouteTicks	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.4	INTEGER	read-create	The delay, in ticks, to reach the route's destination.
INT alaIpxStaticRouteHopCount	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.5	INTEGER	read-create	The number of hops necessary to reach the destination.
ROW alaIpxStaticRouteRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.6	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxStaticRouteTable is constrained by the operational state of the corresponding static route. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxDefRouteTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2		not-accessible	The default route table contains information about the destinations to which all packets are sent when the destination network is not known.
alaIpxDefRouteEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1		not-accessible	One table entry per switch for default route.
INT alaIpxDefRouteVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.1	INTEGER	not-accessible	The VlanId for this filter. If VlanId equals 0, the filter is applied globally.
NET alaIpxDefRouteNet	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.2	NetNumber	read-create	The IPX network number of the router used to reach the first hop in the default route.
ADR alaIpxDefRouteNode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.3	HostAddress	read-create	The IPX node number of the router used to reach the first hop in the default route.
ROW alaIpxDefRouteRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.4	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxDefRouteTable is constrained by the operational state of the corresponding default route entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxExtMsgTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3		not-accessible	The extended RIP and SAP messages table contains information about which vlans use extended RIP and SAP packets.
alaIpxExtMsgEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1		not-accessible	One table entry per Vlan.
INT alaIpxExtMsgVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.1	INTEGER	not-accessible	The VlanId for this filter. If VlanId equals 0, the filter is applied globally.
INT alaIpxExtMsgMode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.2	INTEGER	read-create	Indicates whether extended RIP/SAP packets are sent and received.
ROW alaIpxExtMsgRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.3	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxExtMsgTable is constrained by the operational state of the corresponding watchdog entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
INT alaIpxFlush	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.4	INTEGER	read-write	Flushes the routing and the SAP tables. The tables will then be rebuilt from the broadcast messages received from the networks. Reading this variable is undefined
alaIpxFilterGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2			IPX filtering information.
alaIpxRipSapFilterTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1		not-accessible	The IPX Rip/Sap Filter Table contains information about all filters that have been defined.
alaIpxRipSapFilterEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1		not-accessible	Each entry corresponds to one filter.
INT alaIpxRipSapFilterVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.1	INTEGER	not-accessible	The VlanId for this filter. If VlanId equals 0, the filter is applied globally.
INT alaIpxRipSapFilterType	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.2	INTEGER	not-accessible	The type of filter.
NET alaIpxRipSapFilterNet	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.3	NetNumber	not-accessible	The IPX Network Address to filter. A network address of all 0 's is used to denote All Networks.
NET alaIpxRipSapFilterNetMask	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.4	NetNumber	not-accessible	The IPX Network Mask to be used.
ADR alaIpxRipSapFilterNode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.5	HostAddress	not-accessible	The IPX node address to filter. A node address of all 0 's is used to denote All Nodes.
ADR alaIpxRipSapFilterNodeMask	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.6	HostAddress	not-accessible	The IPX node address mask to be used.
INT alaIpxRipSapFilterSvcType	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.7	INTEGER	not-accessible	The SAP service type on which to filter. The SAP service types are defined by Novell.A value of ALL(65535) indicates that all services will be filtered.
INT alaIpxRipSapFilterMode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.8	INTEGER	read-create	The action defined by this filter. block (1) means packets matching this filter will be blocked, and allow(0) means that packets matching this filter will be allowed.
ROW alaIpxRipSapFilterRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.10	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxRipSapFilterTable is constrained by the operational state of the corresponding filter entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxWatchdogSpoofTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2		not-accessible	The IPX Watchdog Spoofing Table contains information about all of the current IPX WAN watchdog spoofing entry statuses.
alaIpxWatchdogSpoofEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1		not-accessible	Each entry corresponds to one WAN routing service.
INT alaIpxWatchdogSpoofVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.1	INTEGER	not-accessible	The VlanId of the WAN routing service that this entry applies to. If VlanId equals 0, the filter is applied globally to all WAN Vlans.
INT alaIpxWatchdogSpoofMode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.2	INTEGER	read-create	This controls whether the IPX Watchdog Spoofing is enabled or disabled.When enabled, this routing service will spoof IPX Watchdog packets.When disabled, this routing service will not spoof IPX Watchdog packets.
ROW alaIpxWatchdogSpoofRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.3	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxWatchdogSpoofTable is constrained by the operational state of the corresponding watchdog entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxSerialFilterTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3		not-accessible	The IPX Serialization Filtering Table contains information about all of the current IPX WAN serialization filtering entry statuses.
alaIpxSerialFilterEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1		not-accessible	Each entry corresponds to one WAN routing service.
INT alaIpxSerialFilterVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.1	INTEGER	not-accessible	The VlanId of the WAN routing service that this entry applies to. If VlanId equals 0, the filter is applied globally to all WAN Vlans.
INT alaIpxSerialFilterMode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.2	INTEGER	read-create	This controls whether the IPX Serialization Filtering is enabled or disabled.When enabled, this routing service will filter IPX Serialization packets.When disabled, this routing service will not filter IPX Serialization packets.
ROW alaIpxSerialFilterRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.3	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxSerialFilterTable is constrained by the operational state of the corresponding filter entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaSpxKeepaliveSpoofTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4		not-accessible	The SPX Keepalive Spoofing Table contains information about all of the current IPX WAN SPX spoofing filtering entry statuses.
alaSpxKeepaliveSpoofEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1		not-accessible	Each entry corresponds to one WAN routing service.
INT alaSpxKeepaliveSpoofVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.1	INTEGER	not-accessible	The VlanId of the WAN routing service that this entry applies to. If VlanId equals 0, the filter is applied globally to all WAN Vlans.
INT alaSpxKeepaliveSpoofMode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.2	INTEGER	read-create	This controls whether the SPX Keepalive Spoofing is enabled or disabled.When enabled, this routing service will spoof SPX Keepalive packets.When disabled, this routing service will not spoof SPX Keepalive packets.
ROW alaSpxKeepaliveSpoofRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.3	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxKeepaliveSpoofTable is constrained by the operational state of the corresponding keepalive entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxType20Table	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5		not-accessible	The IPX Type 20 Table contains information about all of the current Type 20 filtering entry statuses.
alaIpxType20Entry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1		not-accessible	Each entry corresponds to one Virtual LAN.
INT alaIpxType20VlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.1	INTEGER	not-accessible	The VLAN Id of the routing interface that this entry applies to. If VlanId equals 0, the filter is applied globally.
INT alaIpxType20Mode	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.2	INTEGER	read-create	This controls whether IPX Type 20 packet are enabled or disabled.When enabled, this routing interface will forward Type 20 packets.When disabled, the packets will not.
ROW alaIpxType20RowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.3	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxType20Table is constrained by the operational state of the corresponding type 20 entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alaIpxTimerGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3			IPX timer information.
alaIpxTimerTable	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1		not-accessible	The IPX Timer Table contains information about all of the current Timer adjustments entry statuses.
alaIpxTimerEntry	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1		not-accessible	Each entry corresponds to one Virtual LAN.
INT alaIpxTimerVlanId	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.1	INTEGER	not-accessible	The VLAN Id of the routing interface that this entry applies to. If VlanId equals 0, the filter is applied globally.
INT alaIpxTimerSap	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.2	INTEGER	read-create	This controls whether IPX SAP packet timer duration.
INT alaIpxTimerRip	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.3	INTEGER	read-create	This controls whether IPX RIP packet timer duration.
ROW alaIpxTimerRowStatus	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.4	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. The RowStatus of a currenty active row in the alaIpxTimerTable is constrained by the operational state of the corresponding timer entry. The RowStatus values that are supported are the following: active: This indicates that the row is active and valid. createAndGo: This will create the row and activate it. destroy: This value will deactivate the row and delete from the system.
alcatelIND1IPXMIBConformance	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2
alcatelIND1IPXMIBCompliances	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.1
alcatelIND1IPXMIBCompliance	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.1.1			The compliance statement for IPX Subsystem and ALCATEL-IND1-IPX-MIB.
alcatelIND1IPXMIBGroups	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2
alcatelIND1IPXMIBStaticRouteGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.1			A collection of objects from Static Route Table.
alcatelIND1IPXMIBDefRouteGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.2			A collection of objects from Default Route Table.
alcatelIND1IPXMIBExtMsgGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.3			A collection of objects from Extended Message Table.
alcatelIND1IPXMIBFlushGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.4			A collection of objects to flush the RIP and SAP tables.
alcatelIND1IPXMIBRipSapFilterGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.5			A collection of objects from the RIP and SAP Filter tables.
alcatelIND1IPXMIBWatchdogSpoofGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.6			A collection of objects from the Watchdog spoof tables.
alcatelIND1IPXMIBSerialFilterGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.7			A collection of objects from the Serialization Filter tables.
alcatelIND1IPXMIBKeepaliveSpoofGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.8			A collection of objects from the Keepalive Spoof tables.
alcatelIND1IPXMIBType20Group	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.9			A collection of objects from the Type 20 packet tables.
alcatelIND1IPXMIBTimerGroup	1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2.10			A collection of objects from the RIP and SAP Timer tables.

RFC description

Alcatel IPX routing subsystem management for Novell NetWare network protocol handling.

Start monitoring Alcatel/Alcatel-Lucent OmniSwitches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-IPX-MIB

What Is ALCATEL-IND1-IPX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description