ALCATEL-IND1-IPV6-MIB

All MIBs › ALCATEL-IND1-IPV6-MIB

Organization: Alcatel-Lucent

Last Updated: 2013-07-30

Category: IP and Core Protocols, Vendor: Alcatel-Lucent

Description: Alcatel OmniSwitch IPv6 management MIB for interface addresses, neighbor discovery, and IPv6 forwarding configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-IPV6-MIB?

ALCATEL-IND1-IPV6-MIB is Alcatel's proprietary OmniSwitch MIB for configuring and monitoring IPv6 functionality on the switch, including interface addressing, neighbor discovery, and tunneling. It exposes an interface table for IPv6-enabled VLANs/interfaces, global neighbor-discovery parameters such as stale lifetime and neighbor limits per system and per VRF, a Path MTU discovery control table, and tunnel configuration objects. Its monitoring role is chiefly software/configuration-state visibility for the IPv6 stack — confirming interfaces are correctly enabled and addressed, that neighbor caches haven't hit configured limits, and that PMTU entries are behaving as expected — rather than physical hardware status. It builds on IPv6 concepts defined by IETF standards, such as neighbor discovery and PMTU discovery, while implementing them as Alcatel-proprietary objects rather than depending on an IETF IPv6 MIB directly. It's deployed on Alcatel/Alcatel-Lucent OmniSwitch platforms wherever IPv6 routing or dual-stack VLAN interfaces are enabled. Engineers can download the ALCATEL-IND1-IPV6-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-IPV6-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel/Alcatel-Lucent OmniSwitch with IPv6 routing enabled

Monitoring Examples

An engineer would poll alaIPv6InterfaceTable and check alaIPv6InterfaceRowStatus to confirm a VLAN's IPv6 interface is active, then review alaIPv6NeighborLimit and alaIPv6NeighborVRFLimit against actual neighbor-cache usage to catch a system approaching its neighbor-discovery capacity. alaIPv6NeighborStaleLifetime and alaIPv6PMTUMinLifetime govern how long neighbor and PMTU cache entries persist before re-verification, which matters when diagnosing stale-neighbor connectivity issues. Administrative actions like alaIPv6ClearNeighbors or alaIPv6ClearTraffic are typically invoked to force a fresh neighbor discovery cycle when troubleshooting an IPv6 reachability problem.

What Can Be Monitored

IPv6 interface status
neighbor discovery cache limits/usage
PMTU cache lifetime/entries
IPv6 tunnel configuration
neighbor/traffic clear operations

Imported Objects

From ALCATEL-IND1-BASE

softentIND1Ipv6

OBJECT-IDENTITY

From ALCATEL-IND1-VIRTUALROUTER-MIB

alaVirtualRouterName

OBJECT-TYPE

From IPV6-MIB

ipv6IfIndex	OBJECT-TYPE
ipv6RouteEntry	OBJECT-TYPE

From IPV6-TC

Ipv6Address
Ipv6IfIndexOrZero

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
PhysAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using alaIPv6PMTUHits OID:

Select an Alcatel/Alcatel-Lucent OmniSwitch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type alaIPv6PMTUHits into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of times the path MTU entry has been used. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
alcatelIND1IPv6MIB	1.3.6.1.4.1.6486.801.1.2.1.29.1			This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
alcatelIND1IPv6MIBNotifications	1.3.6.1.4.1.6486.801.1.2.1.29.1.0			Branch For IPv6 MIB Subsystem Notifications.
NTF ndpMaxLimitReached	1.3.6.1.4.1.6486.801.1.2.1.29.1.0.1			This notification is generated when hardware table has reached supported Maximum entries. OS6400 will not generate new ARP request for new nexthops
NTF alaIPv6NeighborLimitExceeded	1.3.6.1.4.1.6486.801.1.2.1.29.1.0.2			Notification that the system-wide neighbor cache limit has been exceeded.
NTF alaIPv6NeighborVRFLimitExceeded	1.3.6.1.4.1.6486.801.1.2.1.29.1.0.3			Notification that a per-VRF neighbor cache limit has been exceeded.
NTF alaIPv6InterfaceNeighborLimitExceeded	1.3.6.1.4.1.6486.801.1.2.1.29.1.0.4			Notification that a per-interface neighbor cache limit has been exceeded.
alcatelIND1IPv6MIBObjects	1.3.6.1.4.1.6486.801.1.2.1.29.1.1
alaIPv6Config	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1
INT alaIPv6ClearNeighbors	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.1	INTEGER	read-write	Clear all non-static entries from the Neighbor table.
INT alaIPv6ClearTraffic	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.2	INTEGER	read-write	Reset all IPv6 traffic counters.
INT alaIPv6ClearPMTUTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.3	INTEGER	read-write	Clear the path MTU table.
U32 alaIPv6PMTUMinLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.4	Unsigned32	read-write	Set the minimum lifetime for entries in the path MTU table.
U32 alaIPv6NeighborStaleLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.5	Unsigned32	read-write	Set the minimum lifetime for neighbor entries in the stale state. In older versions of this MIB the default was specified as 1440 minutes.
OCT alaIPv6GlobalID	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.6	OCTET STRING	read-write	The global ID used in the creation of local IPv6 unicast addresses (RFC 4193). An explicit value may be specified for the global ID or this object may be set to all zero to have a global ID be created based on the algorithm from the RFC.
INT alaIPv6VirtualSourceMAC	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.7	INTEGER	read-write	If set to enable(1) when a packet's source address is a VRRP virtual IPv6 address, the corresponding VRRP virtual MAC will be used as the source L2 address. If set to disable(2), the default, the interface's real MAC will be used as the source L2 address.
U32 alaIPv6NeighborLimit	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.8	Unsigned32	read-write	The system-wide maximum size of the neighbor cache. A value of 0 indicates that no limit will be enforced. The minimum value is 200 entries.
U32 alaIPv6NeighborVRFLimit	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.9	Unsigned32	read-write	The maximum size of the neighbor cache for a specific VRF. A value of 0 indicates that no limit is set. The minimum value is 200 entries.
alaIPv6InterfaceTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2		not-accessible	Table allowing the creation and removal of IPv6 interfaces. The table is indexed by ipv6IfIndex. The value of ipv6IfIndex shall be a four byte value in one of the following formats: 0x0000vvvv - The interface for VLAN vvvv 0x0100tttt - The interface for tunnel tttt 0x02000001 - The IPv6 loopback interface The loopback interface configuration cannot be modified.
alaIPv6InterfaceEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1		not-accessible	An IPv6 interface entry.
ROW alaIPv6InterfaceRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.1	RowStatus	read-create	Used to control the addition and removal of IPv6 interfaces.
STR alaIPv6InterfaceDescription	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.2	SnmpAdminString	read-only	The IPv6 interface's description.
U32 alaIPv6InterfaceMtu	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.3	Unsigned32	read-create	The IPv6 interface's maximum transmission unit.
INT alaIPv6InterfaceType	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.4	INTEGER	read-only	The interface type.
INT alaIPv6InterfaceAdminStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.5	INTEGER	read-create	Interface administrative status.
INT alaIPv6InterfaceSendRouterAdvertisements	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.6	INTEGER	read-create	Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is enable(1). Some interface types (e.g. 6to4 tunnel) cannot send router advertisements so the default (and only) value for those interfaces is disable(2).
U32 alaIPv6InterfaceMaxRtrAdvInterval	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.7	Unsigned32	read-create	The maximum time allowed between sending unsolicited multicast router advertisements from the interface.
T/F alaIPv6InterfaceAdvManagedFlag	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.8	TruthValue	read-create	The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements.
T/F alaIPv6InterfaceAdvOtherConfigFlag	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.9	TruthValue	read-create	The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements.
U32 alaIPv6InterfaceAdvReachableTime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.10	Unsigned32	read-create	The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router.
U32 alaIPv6InterfaceAdvRetransTimer	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.11	Unsigned32	read-create	The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router.
U32 alaIPv6InterfaceAdvDefaultLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.12	Unsigned32	read-create	The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds. The special value zero indicates that the router is not to be used as a default router. The special value 1 indicates that this object's true value should be computed using the formula 3 * alaIPv6InterfaceMaxRtrAdvInterval.
STR alaIPv6InterfaceName	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.13	SnmpAdminString	read-create	The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically assigned.
T/F alaIPv6InterfaceAdvSendMtu	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.14	TruthValue	read-create	The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements.
U32 alaIPv6InterfaceReachableTime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.15	Unsigned32	read-only	In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioning to the stale state. Computed to be between .5 and 1.5 times the alaIPv6InterfaceBaseReachableTime.
U32 alaIPv6InterfaceBaseReachableTime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.16	Unsigned32	read-create	The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above.
U32 alaIPv6InterfaceMinRtrAdvInterval	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.17	Unsigned32	read-create	The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more than .75 times the value of alaIPv6InterfaceMaxRtrAdvInterval. Setting this object to the special value of 0 indicates that the minimum interval should be automatically recalculated using the formula .33 times the value of alaIPv6InterfaceMaxRtrAdvInterval.
U32 alaIPv6InterfaceClockSkew	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.18	Unsigned32	read-create	Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly synchronized clocks.
U32 alaIPv6InterfaceRetransTimer	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.19	Unsigned32	read-create	The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery.
U32 alaIPv6InterfaceDADTransmits	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.20	Unsigned32	read-create	The number of Neighbor Solicitations to send during Duplicate Address Detection. A value of 0 indicates that DAD will not be performed for addresses assigned to the interface.
U32 alaIPv6InterfaceAdvHopLimit	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.21	Unsigned32	read-create	The value placed in the current hop limit field of router advertisements.
INT alaIPv6InterfaceLPND	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.22	INTEGER	read-create	Enable/disable local proxy neighbor discovery.
INT alaIPv6InterfaceRAFilter	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.23	INTEGER	read-create	Enable/disable RA filtering.
U32 alaIPv6InterfaceNeighborLimit	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.24	Unsigned32	read-create	The maximum number o neighbor entries that may be cached on this interface. A value of 0 indicates that no limit is set. The minimum value is 10.
U32 alaIPv6InterfaceRetransBackoff	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.25	Unsigned32	read-create	The neighbor unreachability detection exponential backoff base. A value of 1 indicates the use of fixed interval retransmissions.
U32 alaIPv6InterfaceRetransMax	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.26	Unsigned32	read-create	The maximum number of neighbor solicitations to be sent during neighbor discovery or neighbor unreachability detection.
alaIPv6TunnelConfig	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3
alaIPv6ConfigTunnelTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2		not-accessible	Table for IPv6 configured tunnels. This table contains the tunnel-specific information extending the corresponding tunnel interface entry in alaIPv6InterfaceTable.
alaIPv6ConfigTunnelEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1		not-accessible	A entry contains the objects for an IPv6 configured tunnel.
IP alaIPv6ConfigTunnelV4Source	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.1	IpAddress	read-create	The source IPv4 address for the tunnel.
IP alaIPv6ConfigTunnelV4Dest	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.2	IpAddress	read-create	The destination IPv4 address for the tunnel.
alaIPv6InterfaceAddressTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4		not-accessible	Table allowing the creation and removal of IPv6 addresses assigned to interfaces.
alaIPv6InterfaceAddressEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1		not-accessible	An IPv6 interface address entry. The same link-local address may be assigned to multiple interfaces. A global address may only be assigned to a single interface.
ROW alaIPv6InterfaceAddressRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.1	RowStatus	read-create	Used to control the addition and removal of IPv6 interface addresses.
ADR alaIPv6InterfaceAddress	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.2	Ipv6Address	not-accessible	An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface.
U32 alaIPv6InterfaceAddressPrefixLength	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.3	Unsigned32	read-create	The number of bits that are significant in the IPv6 address' prefix.
T/F alaIPv6InterfaceAddressAnycastFlag	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.4	TruthValue	read-create	This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.
INT alaIPv6InterfaceAddressDADStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.5	INTEGER	read-create	The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such cases, duplicate address detection will be performed again for the address.
alaIPv6InterfaceEUI64AddressTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5		not-accessible	Table allowing the creation and removal of IPv6 addresses formed by appending an EUI-64 interface identifier to the specified prefix. This table is mainly used for the creation of such addresses. After creation they can be managed via the alaIPv6InterfaceAddressTable.
alaIPv6InterfaceEUI64AddressEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1		not-accessible	An IPv6 interface EUI-64 address entry.
ROW alaIPv6InterfaceEUI64AddressRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.1	RowStatus	read-create	Used to control the addition and removal of IPv6 interface EUI-64 addresses.
ADR alaIPv6InterfaceEUI64AddressPrefix	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.2	AlaIPv6AddressPrefix	not-accessible	The prefix for the EUI-64 address.
U32 alaIPv6InterfaceEUI64AddressPrefixLength	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.3	Unsigned32	read-create	The number of bits that are significant in the IPv6 address' prefix.
OCT alaIPv6InterfaceEUI64AddressIdentifier	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.4	OCTET STRING	read-only	The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address.
alaIPv6NeighborTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6		not-accessible	The IPv6 neighbor table. Much of this information is available in the RFC-2465 ipv6NetToMediaTable. However, that table does not allow the static configuration of neighbor entries (all objects except for ipv6NetToMediaValid are read-only).
alaIPv6NeighborEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1		not-accessible	Each entry contains one IPv6 address to `physical' address equivalence (a neighbor).
ADR alaIPv6NeighborNetAddress	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.1	Ipv6Address	not-accessible	The neighbor's IPv6 Address.
PHY alaIPv6NeighborPhysAddress	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.2	PhysAddress	read-create	The neighbor's media-dependent `physical' address.
U32 alaIPv6NeighborSlot	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.3	Unsigned32	read-create	The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not applicable.
U32 alaIPv6NeighborPort	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.4	Unsigned32	read-create	The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not applicable.
INT alaIPv6NeighborType	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.5	INTEGER	read-only	The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. All entries added via this table will have the type static(3) and only static entries may be removed via this table.
INT alaIPv6NeighborState	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.6	INTEGER	read-only	The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used.
TIM alaIPv6NeighborLastUpdated	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.7	TimeStamp	read-only	The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
ROW alaIPv6NeighborRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.8	RowStatus	read-create	Used to control the addition and removal of static entries in the neighbor table.
U32 alaIPv6NeighborLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.9	Unsigned32	read-only	The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero indicates the neighbor will remain in its current state indefinitely.
INT alaIPv6NeighborReachability	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.10	INTEGER	read-only	The reachability status of the neighbor.
U32 alaIPv6NeighborChassis	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.11	Unsigned32	read-create	On a multi-chasis system, the chassis used to reach the neighbor. On a single-chassis system this value is always 0. On read, a value of zero may indicate that the chassis is not known/not applicable.
alaIPv6StaticRouteTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7		not-accessible	This table has been superseded by alaIprmV6StaticRouteTable in ALCATEL-IND1-IPRMV6-MIB. Table allowing the creation and removal of static IPv6 routes.
alaIPv6StaticRouteEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1		not-accessible	A static route entry.
ADR alaIPv6StaticRouteDest	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.1	Ipv6Address	not-accessible	The destination IPv6 address of this static route. This object may not take a Multicast address value.
I32 alaIPv6StaticRoutePfxLength	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.2	Integer32	not-accessible	Indicates the prefix length of the destination address.
IPV alaIPv6StaticRouteIfIndex	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.3	Ipv6IfIndexOrZero	read-create	If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop address types the value is zero.
ADR alaIPv6StaticRouteNextHop	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.4	Ipv6Address	read-create	The IPv6 address of the next hop towards the destination.
U32 alaIPv6StaticRouteMetric	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.5	Unsigned32	read-create	The routing metric for this route. The lower the value, the higher the priority for the static route.
ROW alaIPv6StaticRouteRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.6	RowStatus	read-create	Used to control the addition and removal of static routes.
alaIPv6HostTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8		not-accessible	Local table mapping host names to IPv6 addresses. This provides the equivalent of /etc/hosts for IPv6.
alaIPv6HostEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1		not-accessible	A entry maps a host name to an IPv6 address.
STR alaIPv6HostName	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.1	SnmpAdminString	not-accessible	A host name to be mapped to an IPv6 address.
ADR alaIPv6HostAddress	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.2	Ipv6Address	not-accessible	The IPv6 address mapped to the host name.
ROW alaIPv6HostRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.3	RowStatus	read-create	Allows host name/IPv6 address mappings to be created and deleted in this table.
alaIPv6InterfacePrefixTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9		not-accessible	Table allowing the creation and removal of IPv6 prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. Default: all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent. The link-local prefix is not included in the list of advertised prefixes.
alaIPv6InterfacePrefixEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1		not-accessible	An IPv6 interface prefix entry.
ROW alaIPv6InterfacePrefixRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.1	RowStatus	read-create	Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages.
ADR alaIPv6InterfacePrefix	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.2	Ipv6Address	not-accessible	The prefix associated with this interface.
U32 alaIPv6InterfacePrefixLength	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.3	Unsigned32	not-accessible	The length of the prefix in bits.
U32 alaIPv6InterfacePrefixValidLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.4	Unsigned32	read-create	The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
T/F alaIPv6InterfacePrefixOnLinkFlag	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.5	TruthValue	read-create	The value to be placed in the on-link flag (L-bit) field in the Prefix Information option.
U32 alaIPv6InterfacePrefixPreferredLifetime	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.6	Unsigned32	read-create	The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
T/F alaIPv6InterfacePrefixAutonomousFlag	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.7	TruthValue	read-create	The value to be placed in the Autonomous Flag field in the Prefix Information option.
INT alaIPv6InterfacePrefixSource	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.8	INTEGER	read-only	The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration the value will be dynamic(2).
T/F alaIPv6InterfacePrefixValidLifetimeDecrement	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.9	TruthValue	read-create	If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixValidLifetime.
DAT alaIPv6InterfacePrefixValidLifetimeExpire	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.10	DateAndTime	read-create	The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true.
T/F alaIPv6InterfacePrefixPreferredLifetimeDecrement	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.11	TruthValue	read-create	If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixPreferredLifetime.
DAT alaIPv6InterfacePrefixPreferredLifetimeExpire	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.12	DateAndTime	read-create	The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true.
alaIPv6PMTUTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10		not-accessible	Table allowing the retrieval of the known IPv6 path MTU value.
alaIPv6PMTUEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1		not-accessible	An IPv6 path MTU entry.
ADR alaIPv6PMTUDest	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.1	Ipv6Address	not-accessible	The destination address of the IPv6 path.
U32 alaIPv6PMTU	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.2	Unsigned32	read-only	The path's MTU.
U32 alaIPv6PMTUExpire	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.3	Unsigned32	read-only	The minimum time remaining before the PMTU entry is removed from the table.
C32 alaIPv6PMTUHitsEx	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.4	Counter32	read-only	The number of times the path MTU entry has been used.
C32 alaIPv6PMTUUpdates	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.5	Counter32	read-only	The number of times the path MTU entry has been updated.
alaIPv6RouteFlagsTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11		not-accessible	Table allowing the retrieval of the flags for IPv6 route entries.
alaIPv6RouteFlagsEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1		not-accessible	An IPV6 route flags entry.
T/F alaIPv6RouteFlagsUp	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.1	TruthValue	read-only	True if the Up (U) flag is set on the route.
T/F alaIPv6RouteFlagsGateway	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.2	TruthValue	read-only	True if the Gateway (G) flag is set on the route.
T/F alaIPv6RouteFlagsHost	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.3	TruthValue	read-only	True if the Host (H) flag is set on the route.
T/F alaIPv6RouteFlagsStatic	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.4	TruthValue	read-only	True if the Static (S) flag is set on the route.
T/F alaIPv6RouteFlagsCloneable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.5	TruthValue	read-only	True if the Cloneable (C) flag is set on the route.
T/F alaIPv6RouteFlagsDiscard	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.6	TruthValue	read-only	True if the Discard/Blackhole (B) flag is set on the route.
T/F alaIPv6RouteFlagsECMP	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.7	TruthValue	read-only	True if the ECMP (E) flag is set on the route.
T/F alaIPv6RouteFlagsTransient	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.8	TruthValue	read-only	True if route has not been replaced by valid route after takeover.
alaIPv6LocalUnicastTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13		not-accessible	Table allowing the creation and removal of local IPv6 unicast addresses (RFC 4193) on an interface.
alaIPv6LocalUnicastEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1		not-accessible	An local unicast IPv6 address entry.
OCT alaIPv6LocalUnicastGlobalID	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.1	OCTET STRING	not-accessible	The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value.
OCT alaIPv6LocalUnicastSubnetID	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.2	OCTET STRING	not-accessible	The subnet ID portion of the local IPv6 unicast address.
OCT alaIPv6LocalUnicastInterfaceID	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.3	OCTET STRING	not-accessible	The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero.
U32 alaIPv6LocalUnicastPrefixLength	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.4	Unsigned32	read-create	The number of bits that are significant in the IPv6 address prefix.
T/F alaIPv6LocalUnicastEUI64	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.5	TruthValue	read-create	If true(1) the interface identifier is formed from an automatically generated EUI-64 value.
ROW alaIPv6LocalUnicastRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.6	RowStatus	read-create	Used to control the addition and removal of local IPv6 unicast addresses.
alaIPv6RAFilterTrustedTable	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14		not-accessible	Table allowing the creation and removal of trusted ports for an interface's RA filtering.
alaIPv6RAFilterTrustedEntry	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1		not-accessible	An RA filter trusted port entry.
U32 alaIPv6RAFilterTrustedChassis	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.1	Unsigned32	not-accessible	On a multi-chasis system, the chassis on which the trusted port resides. On a single-chassis system or when specifying a link aggregation this value is always 0.
U32 alaIPv6RAFilterTrustedSlot	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.2	Unsigned32	not-accessible	The slot on which the trusted port resides. When specifying a link aggregation this value is always 0.
U32 alaIPv6RAFilterTrustedPort	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.3	Unsigned32	not-accessible	The trusted port's physical port number or the id of a link aggregation.
ROW alaIPv6RAFilterTrustedRowStatus	1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.4	RowStatus	read-create	Used to control the addition and removal of an RA filter's trusted ports.
alcatelIND1IPv6MIBConformance	1.3.6.1.4.1.6486.801.1.2.1.29.1.2
alcatelIND1IPv6MIBCompliances	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1
alaIPv6Compliance	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1.1			The compliance statement for switches with Alcatel IPv6 stack and implementing ALCATEL-IND1-IPV6-MIB.
alcatelIND1IPv6MIBGroups	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2
alaIPv6TunnelConfigGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.1			A collection of objects to support management of Alcatel IPv6 tunneling.
alaIPv6ConfigGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.2			A collection of objects to support management of configuration parameters of Alcatel IPv6 stack.
alaIPv6NeighborGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.3			A collection of objects to support management of IPv6 neighbors.
alaIPv6StaticRouteGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.4			A collection of objects to support management of IPv6 static routes.
alaIPv6InterfaceGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.5			A collection of objects to support management of IPv6 interfaces.
alaIPv6InterfaceAddressGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.6			A collection of objects to support management of IPv6 addresses assigned to interfaces.
alaIPv6InterfaceEUI64AddressGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.7			A collection of objects to support management of IPv6 EUI-64 addresses assigned to interfaces.
alaIPv6InterfacePrefixGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.8			A collection of objects to support management of IPv6 prefixes assigned to interfaces.
alaIPv6PMTUGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.9			A collection of objects to support management of IPv6 path MTUs.
alaIPv6RouteFlagsGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.10			A collection of objects to support management of IPv6 route flags.
alaIPv6LocalUnicastGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.11			A collection of objects to support management of local IPv6 unicast addresses (RFC 4193).
alaIPv6HostGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.12			A collection of objects to support management of IPv6 addresses assigned to Host.
alcatelIND1IPv6NotificationGroup	1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.13			The AlcatelIND1IPv6 MIB Notification Group.

RFC description

Alcatel IPv6 routing, neighbor discovery, and address configuration with virtual router support.

Start monitoring Alcatel/Alcatel-Lucent OmniSwitches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-IPV6-MIB