ZTE-AN-UAPS-MIB

All MIBs › ZTE-AN-UAPS-MIB

Organization: ZTE Corporation

Last Updated: 2013-04-07

Category: ZTE Access Node (ZTE-AN) Management

Description: Manages ZTE access node UAPS (Unified Authentication Policy Service) subscriber authentication settings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZTE-AN-UAPS-MIB?

ZTE-AN-UAPS-MIB implements the Unified Authentication Policy Service on ZTE Access Node equipment, centralizing configuration for subscriber authentication methods such as 802.1X, PPPoE, or web-portal login applied per port or service. It exposes authentication policy configuration and enable state for the device. It is a software/protocol-configuration MIB used to verify that subscriber authentication is correctly enforced on a given port, rather than a hardware-health monitor. It builds on standard 802.1X and general AAA/RADIUS authentication concepts. It is typically deployed by broadband access operators to unify and audit subscriber authentication policy across many access ports. Engineers can download the ZTE-AN-UAPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-UAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE access node (DSLAM/OLT broadband access platform)

Monitoring Examples

No specific object names were present in the source, so the following scenario is inferred from module_desc: an operator would check the UAPS policy configuration on a port to confirm which authentication method is currently enabled. An unexpectedly disabled authentication policy would explain why unauthenticated subscriber traffic is passing through that port, a security gap worth flagging.

What Can Be Monitored

authentication policy enable state
per-port authentication method configuration
UAPS policy assignment

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

From ZTE-AN-SMI

zxAnBridge

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
zxAnUapsMib	1.3.6.1.4.1.3902.1082.40.80			The MIB module for the management of UAPS function.
zxAnUapsGlobalObjects	1.3.6.1.4.1.3902.1082.40.80.1
BIT zxAnUapsCapabilities	1.3.6.1.4.1.3902.1082.40.80.1.1	Bits	read-only	The UAPS management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported. portsTableSupported(0): value 1 means zxAnUapsPrimaryPortsTable and zxAnUapsSecondaryPortsTable are supported. In this case, the UAPS primary port list and second port list should be created or deleted by zxAnUapsPrimaryPortsTable and zxAnUapsSecondaryPortsTable, instead of the zxAnUapsPrimaryPortList and zxAnUapsPrimaryPortList.
zxAnUapsObjects	1.3.6.1.4.1.3902.1082.40.80.2
zxAnUapsGroupTable	1.3.6.1.4.1.3902.1082.40.80.2.2		not-accessible	This table includes the managed objects of the UAPS group.
zxAnUapsGroupEntry	1.3.6.1.4.1.3902.1082.40.80.2.2.1		not-accessible	An entry in zxAnUapsGroupTable.
I32 zxAnUapsGroupIndex	1.3.6.1.4.1.3902.1082.40.80.2.2.1.1	Integer32	not-accessible	The index of UAPS group.
STR zxAnUapsGroupName	1.3.6.1.4.1.3902.1082.40.80.2.2.1.2	DisplayString	read-create	The name of UAPS group.
OID zxAnUapsPrimaryPortList	1.3.6.1.4.1.3902.1082.40.80.2.2.1.3	OBJECT IDENTIFIER	read-create	The primary UAPS ports. The maximum port numbers joined in this port list should not be more than 4. Each member of this variable is ifIndex of a port.
OID zxAnUapsSecondaryPortList	1.3.6.1.4.1.3902.1082.40.80.2.2.1.4	OBJECT IDENTIFIER	read-create	The secondary UAPS ports. The maximum port numbers joined in this port list should not be more than 4. Furthermore, the port numbers joined in this port list should be equal to the zxAnUapsPrimaryPortList's. Each number of this variable is ifIndex of a port.
INT zxAnUapsPortWorkingStatus	1.3.6.1.4.1.3902.1082.40.80.2.2.1.5	INTEGER	read-only	It indicates which port group is in working state.
INT zxAnUapsAutoFailbackEnable	1.3.6.1.4.1.3902.1082.40.80.2.2.1.6	INTEGER	read-create	Enables or disables recovery to the UAPS primary port automatically when the primary port is normal again.
IPt zxAnUapsNextHopIpType	1.3.6.1.4.1.3902.1082.40.80.2.2.1.7	InetAddressType	read-create	Next hop IP type.
IP zxAnUapsNextHopIp	1.3.6.1.4.1.3902.1082.40.80.2.2.1.8	InetAddress	read-create	Next hop IP. Only IPv4 is supported now. If it is 0.0.0.0, UAPS will not check the link of next hop.
INT zxAnUapsIpLinkType	1.3.6.1.4.1.3902.1082.40.80.2.2.1.9	INTEGER	read-create	The link type used to check IP link status.
I32 zxAnUapsIpLinkCheckRetries	1.3.6.1.4.1.3902.1082.40.80.2.2.1.10	Integer32	read-create	The retries of checking link status.
I32 zxAnUapsIpLinkCheckTimeout	1.3.6.1.4.1.3902.1082.40.80.2.2.1.11	Integer32	read-create	The timeout of checking link status.
INT zxAnUapsIpLinkStatus	1.3.6.1.4.1.3902.1082.40.80.2.2.1.12	INTEGER	read-only	The status of IP link.
INT zxAnUapsSwapMode	1.3.6.1.4.1.3902.1082.40.80.2.2.1.13	INTEGER	read-create	It indicates swap mode. common: If one port of working port list down, all ports will swap to slave port list. trunk: Only when all working ports down, ports will swap to slave port list. upPortNum: If the number of up working ports is less than the number of up slave ports, swap to slave port list.
INT zxAnUapsForceSwap	1.3.6.1.4.1.3902.1082.40.80.2.2.1.14	INTEGER	read-create	Force to swap the primary and secondary ports.
INT zxAnUapsSwapReason	1.3.6.1.4.1.3902.1082.40.80.2.2.1.15	INTEGER	read-only	It indicates the reason of swap. failback(1): Primary port is recovery. failoverByPhyLinkDown(2): Primary port is in fault of physical layer. failoverByIpLinkDown(3): Primary port is in fault of IP layer. forceSwap(4): Force swap. swapByPhyLinkUp(5): In upPortNum mode, swap may be caused by physical link up. swapByPortAdded(6): Swap caused by adding new port. swapByPortDeleted(7): Swap caused by deleting port. swapBySwapModeChanged(8): Swap caused by changing swap mode. noSwap(255): No swap.
BIT zxAnUapsSwapRequestInCache	1.3.6.1.4.1.3902.1082.40.80.2.2.1.16	Bits	read-only	It indicates the swap request in memory.
INT zxAnUapsSwapLastRequest	1.3.6.1.4.1.3902.1082.40.80.2.2.1.17	INTEGER	read-only	It indicates the last swap request.
I32 zxAnUapsProtectionTime	1.3.6.1.4.1.3902.1082.40.80.2.2.1.18	Integer32	read-create	The protection time of UAPS. When the fail time of port is larger than it, the UAPS module should failover to the secondary port.
T/F zxAnUapsIsInProtectionTime	1.3.6.1.4.1.3902.1082.40.80.2.2.1.19	TruthValue	read-only	It indicates if the UAPS is in protection time status.
INT zxAnUapsSlavePortTxOptShutdown	1.3.6.1.4.1.3902.1082.40.80.2.2.1.20	INTEGER	read-create	If it is enabled, the slave port transmitted optical signal will be shutdown.
U32 zxAnUapsFailureTime	1.3.6.1.4.1.3902.1082.40.80.2.2.1.21	Unsigned32	read-only	It indicates the time since the secondary UAPS ports became in working or any port of this UAPS group was down. After the primary UAPS ports become in working and all ports of this UAPS group are up, it's value will be zero.
ROW zxAnUapsGroupRowStatus	1.3.6.1.4.1.3902.1082.40.80.2.2.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnUapsPrimaryPortsTable	1.3.6.1.4.1.3902.1082.40.80.2.3		not-accessible	This table includes the primary ports of the UAPS group.
zxAnUapsPrimaryPortsEntry	1.3.6.1.4.1.3902.1082.40.80.2.3.1		not-accessible	An entry in zxAnUapsPrimaryPortsTable.
ROW zxAnUapsPrimaryPortsRowStatus	1.3.6.1.4.1.3902.1082.40.80.2.3.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnUapsSecondaryPortsTable	1.3.6.1.4.1.3902.1082.40.80.2.4		not-accessible	This table includes the secondary ports of the UAPS group.
zxAnUapsSecondaryPortsEntry	1.3.6.1.4.1.3902.1082.40.80.2.4.1		not-accessible	An entry in zxAnUapsSecondaryPortsTable.
ROW zxAnUapsSecondaryPortsRowStatus	1.3.6.1.4.1.3902.1082.40.80.2.4.1.50	RowStatus	read-create	The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
zxAnUapsNotifications	1.3.6.1.4.1.3902.1082.40.80.3
NTF zxAnUapsSwappedTrap	1.3.6.1.4.1.3902.1082.40.80.3.1			It indicates the primary and secondary port of UAPS module has swapped.
NTF zxAnUapsSwappedAlm	1.3.6.1.4.1.3902.1082.40.80.3.2			A zxAnUapsSwappedAlm is sent when the agent has detected that the primary/secondary ports of UAPS module have swapped.
NTF zxAnUapsSwappedClr	1.3.6.1.4.1.3902.1082.40.80.3.3			A zxAnUapsSwappedClr trap is sent when the agent has detected that the zxAnUapsSwappedAlm is cleared manually.

RFC description

Manages Unified Access Point Services (UAPS) redundancy groups on ZTE access network equipment.

Start monitoring ZTE access node (DSLAM/OLT broadband access platform) (unified subscriber-authentication policy config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZTE-AN-UAPS-MIB

What Is ZTE-AN-UAPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description