All MIBs › ZTE-AN-OTDR-MIB
Organization: ZTE Corporation
Last Updated: 2013-03-05
Category: ZTE Access Node (ZTE-AN) Management
Description: Manages ZTE access node OTDR (Optical Time Domain Reflectometer) test operations for fiber fault location.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ZTE-AN-OTDR-MIB?
ZTE-AN-OTDR-MIB manages Optical Time Domain Reflectometer (OTDR) test capability built into ZTE Access Node equipment, used to remotely test fiber spans and locate breaks, splices, or excessive loss points without dispatching a technician with handheld test gear. It exposes global OTDR equipment configuration, per-interface test objects, and two distinct test-type object groups -- fast tests (quick go/no-go fiber checks) and routine/scheduled tests (more thorough periodic sweeps) -- along with a notifications group for test-completion or fault events. Its monitoring value is centered on fiber-plant health and fault isolation: an operator triggers or schedules an OTDR test on a PON/fiber interface and reads back the fault-distance and loss results to pinpoint exactly where a fiber break or bad splice has occurred, and watches for automatic OTDR fault notifications on a fiber cut. It is a ZTE-proprietary optical-diagnostics MIB with no apparent dependency on an IETF standard, closely tied to the physical PON/fiber interfaces it tests. It is deployed on ZTE access nodes serving PON/fiber access networks, used by field operations for remote fiber troubleshooting, and the ZTE-AN-OTDR-MIB download is available to field engineers who want to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-OTDR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ZTE Access Node (PON/fiber interfaces with integrated OTDR)
Monitoring Examples
An admin would use zxAnOtdrFastTestObjects to kick off a quick OTDR check on a suspect fiber interface, or rely on zxAnOtdrRoutineTestObjects for scheduled periodic sweeps, then read the results under zxAnOtdrIfObjects to see the distance to a fault and its estimated loss. zxAnOtdrGlobalObjects holds device-wide OTDR equipment configuration, while zxAnOtdrNotifications delivers an alert when a test completes or detects a fiber fault, letting operations jump straight to the reported break location rather than dispatching a technician to search the span. zxAnOtdrObjects is the overall subtree grouping these OTDR test objects together.
What Can Be Monitored
- OTDR fast-test results
- OTDR routine/scheduled test results
- fiber fault distance/location
- fiber loss measurement
- OTDR test-completion/fault notifications
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowStatus |
From ZTE-AN-OFD-SMI
| zxAnOfd | MODULE-IDENTITY |
How to Use in IPNetwork Monitor
Example using zxAnOtdrCtrlCardCurrentTemp OID:
Select a ZTE Access Node (PON/fiber interfaces with integrated OTDR) (fiber-fault-distance/loss test-result status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxAnOtdrCtrlCardCurrentTemp into the Find box to locate it in the OID tree, then select it and click OK. The current control card temperature of OTDR equipment. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the reported value exceeds the level expected for healthy operation, since sustained high temperature often precedes thermal shutdown or hardware degradation. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| zxAnOtdrMib | 1.3.6.1.4.1.3902.1083.5 | The MIB module for the management of OTDR equipment. | ||
| zxAnOtdrGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1 | |||
| zxAnOtdrCapacityGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.1 | |||
| STR zxAnOtdrWaveLengthList | 1.3.6.1.4.1.3902.1083.5.1.1.1 | DisplayString | read-only | The wave length supported by OTDR. The value divided by '|'. The unit of wave length is nm. PON OLTs support 1625. eOMUs support 1550|1625. |
| STR zxAnOtdrTestPulseWidthList | 1.3.6.1.4.1.3902.1083.5.1.1.2 | DisplayString | read-only | The pulse width supported by OTDR. The value divided by '|'. The unit of pulse width is ns. The value 200001 means 2.5ns. e.g., 5|10|30|100|200|500|10000|20000|200001. |
| I32 zxAnOtdrTotalPorts | 1.3.6.1.4.1.3902.1083.5.1.1.3 | Integer32 | read-only | The total port number of OTDR. |
| STR zxAnOtdrTestSeqCodeLenList | 1.3.6.1.4.1.3902.1083.5.1.1.4 | DisplayString | read-only | The sequence code length supported by OTDR. The value divided by '|'. PON OLTs support 512|1024|2048|4096. eOMUs support 64|256|512|1024. |
| STR zxAnOtdrTestSeqCodeWidthList | 1.3.6.1.4.1.3902.1083.5.1.1.5 | DisplayString | read-only | The sequence code width supported by OTDR. The value divided by '|'. The unit of pulse width is ns. PON OLTs support 5|10|20|30|50. eOMUs support 5|10|20|30. |
| INT zxAnOtdrDualWavelengthTestMode | 1.3.6.1.4.1.3902.1083.5.1.1.6 | INTEGER | read-only | The test mode of dual wavelength. cascade(1): dual wavelength testing on two NEs by cascade. nonCascade(2): dual wavelength testing on one NE. |
| BIT zxAnOtdrCapabilities | 1.3.6.1.4.1.3902.1083.5.1.1.51 | Bits | read-only | The OTDR capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. - fastHealthPrfDiff(0): value 1 means supporting zxAnOtdrIfHealthTestParamPrf and zxAnOtdrTestType. - seqCodeLen(1): value 1 means supporting zxAnOtdrTestParamPrfSeqCodeLen. - routineTaskTestMode(2): value 1 means supporting zxAnOtdrRoutineTaskTestMode. - priorityTaskTest(3): value 1 means supporting zxAnOtdrFastTestPriority and zxAnOtdrFastTestRequestSource. - reflectorTest(4): value 1 means supporting zxAnOtdrIfReflectorTestParamPrf and zxAnOtdrTestType. - globalTestParamPrf(5): value 1 means supporting global test parameter profile. - opticalFiberLabefaction(6): value 1 means supporting optical fiber labefaction predication. - bothwayTest(7): value 1 means supporting zxAnOtdrIfBothwayTestParamPrf and zxAnOtdrTestType. - controlCardIndependentTest(8): value 1 means supporting the control card test without line card. |
| zxAnOtdrEnvGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.2 | |||
| zxAnOtdrEnvCtrlCardGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.2.1 | |||
| I32 zxAnOtdrCtrlCardCurrentTempEx | 1.3.6.1.4.1.3902.1083.5.1.2.1.1 | Integer32 | read-only | The current control card temperature of OTDR equipment. |
| I32 zxAnOtdrCtrlCardTempHighThresh | 1.3.6.1.4.1.3902.1083.5.1.2.1.2 | Integer32 | read-write | The high threshold of the control card temperature, the zxAnOtdrEnvCtrlCardHighTempAlm trap should be generated when zxAnOtdrCtrlCardCurrentTemp is higher than it. Otherwise, zxAnOtdrEnvCtrlCardHighTempClr trap should be generated when zxAnOtdrCtrlCardCurrentTemp is lower than it. |
| I32 zxAnOtdrCtrlCardTempLowThresh | 1.3.6.1.4.1.3902.1083.5.1.2.1.3 | Integer32 | read-write | The low threshold of the control card temperature, the zxAnOtdrEnvCtrlCardLowTempAlm trap should be generated when zxAnOtdrCtrlCardCurrentTemp is lower than it. Otherwise, zxAnOtdrEnvCtrlCardLowTempClr trap should be generated when zxAnOtdrCtrlCardCurrentTemp is higher than it. |
| zxAnOtdrEnvFanGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.2.2 | |||
| INT zxAnOtdrEnvFanStatus | 1.3.6.1.4.1.3902.1083.5.1.2.2.1 | INTEGER | read-only | The fan status. When zxAnOtdrEnvFanStatus is abnormal, zxAnOtdrEnvFanFailureAlm trap should be sent to manager. If zxAnOtdrEnvFanStatus is normal, zxAnOtdrEnvFanFailureClr trap should be sent. |
| INT zxAnOtdrEnvFanOperStatus | 1.3.6.1.4.1.3902.1083.5.1.2.2.2 | INTEGER | read-only | The operational status of fan. |
| zxAnOtdrEnvApdGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.2.3 | |||
| I32 zxAnOtdrEnvApdCurrentTemp | 1.3.6.1.4.1.3902.1083.5.1.2.3.1 | Integer32 | read-only | The current temperature of APD. |
| I32 zxAnOtdrEnvApdTempHighThresh | 1.3.6.1.4.1.3902.1083.5.1.2.3.2 | Integer32 | read-write | The high threshold of the APD temperature, the zxAnOtdrEnvApdHighTempAlm trap should be generated when zxAnOtdrEnvApdCurrentTemp is higher than it. Otherwise, zxAnOtdrEnvApdHighTempClr trap should be generated when zxAnOtdrEnvApdCurrentTemp is lower than it. |
| I32 zxAnOtdrEnvApdTempLowThresh | 1.3.6.1.4.1.3902.1083.5.1.2.3.3 | Integer32 | read-write | The low threshold of the APD temperature, the zxAnOtdrEnvApdLowTempAlm trap should be generated when zxAnOtdrEnvApdCurrentTemp is lower than it. Otherwise, zxAnOtdrEnvApdLowTempClr trap should be generated when zxAnOtdrEnvApdCurrentTemp higher than it. |
| zxAnOtdrPortUtilGlobalObjects | 1.3.6.1.4.1.3902.1083.5.1.3 | |||
| I32 zxAnOtdrPortUtilization | 1.3.6.1.4.1.3902.1083.5.1.3.1 | Integer32 | read-only | The current port utilization of OTDR equipment. |
| I32 zxAnOtdrPortUtilizationThresh | 1.3.6.1.4.1.3902.1083.5.1.3.2 | Integer32 | read-write | The threshold of zxAnOtdrPortUtilization. When zxAnOtdrPortUtilization exceeds this threshold, the zxAnOtdrPortUtlExceedAlm trap should be generated. |
| zxAnOtdrObjects | 1.3.6.1.4.1.3902.1083.5.2 | |||
| zxAnOtdrIfObjects | 1.3.6.1.4.1.3902.1083.5.2.1 | |||
| zxAnOtdrIfGlobalObjects | 1.3.6.1.4.1.3902.1083.5.2.1.1 | |||
| STR zxAnOtdrGlobalTestParamPrf | 1.3.6.1.4.1.3902.1083.5.2.1.1.1 | DisplayString | read-write | The OTDR global test parameter profile name list. The global profile is applied to the interface when the interface test parameter profile is unconfigured. |
| STR zxAnOtdrGlobalNetworkPropertyPrf | 1.3.6.1.4.1.3902.1083.5.2.1.1.2 | DisplayString | read-write | The OTDR global network property profile name list. The global profile is applied to the interface when the interface network property profile is unconfigured. |
| STR zxAnOtdrGlobalAcceptanceTestPrf | 1.3.6.1.4.1.3902.1083.5.2.1.1.3 | DisplayString | read-write | The OTDR acceptance test parameter profile name list, such as 'DEFAULT_ACCEPTANCE_1,DEFAULT_ACCEPTANCE_2,DEFAULT_ACCEPTANCE_3', which are in order of decreasing priority. The global profile is applied to the interface when zxAnOtdrIfAcceptanceTestPrf is unconfigured. |
| zxAnOtdrTestParamPrfTable | 1.3.6.1.4.1.3902.1083.5.2.1.2 | not-accessible | This table includes OTDR test parameter Profile information. | |
| zxAnOtdrTestParamPrfEntry | 1.3.6.1.4.1.3902.1083.5.2.1.2.1 | not-accessible | OTDR test parameter profile entry. | |
| STR zxAnOtdrTestParamPrfName | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.1 | DisplayString | not-accessible | OTDR test parameter profile name. |
| INT zxAnOtdrTestParamPrfMode | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.2 | INTEGER | read-create | OTDR test mode. When the mode is pulseMethod, zxAnOtdrTestParamPrfWaveLength, zxAnOtdrTestParamPrfDistance, zxAnOtdrTestParamPrfFiberIor, zxAnOtdrTestParamPrfPulseWidth, zxAnOtdrTestParamPrfDuration are valid. When the mode is sequenceMethod, zxAnOtdrTestParamPrfWaveLength, zxAnOtdrTestParamPrfDistance, zxAnOtdrTestParamPrfFiberIor, zxAnOtdrTestParamPrfDuration, zxAnOtdrTestParamPrfSeqCodeLen, zxAnOtdrTestParamPrfSeqCodeWidth are valid. |
| I32 zxAnOtdrTestParamPrfWaveLength | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.3 | Integer32 | read-create | OTDR test wave length. |
| I32 zxAnOtdrTestParamPrfDistance | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.4 | Integer32 | read-create | OTDR test distance. |
| I32 zxAnOtdrTestParamPrfFiberIor | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.5 | Integer32 | read-create | OTDR test fiber IOR. The range is from 1.4*(10^6) to 1.6*(10^6). |
| I32 zxAnOtdrTestParamPrfPulseWidth | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.6 | Integer32 | read-create | OTDR test pulse width. '0' means not configured. A value less than 200000 is mapped to an integer pulse width value. A value greater than 200000 is mapped to a specific pulse width value. e.g., The value 5 is mapped to 5ns, the value 200001 is mapped to 2.5ns. |
| I32 zxAnOtdrTestParamPrfDuration | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.7 | Integer32 | read-create | OTDR test duration. '0' means not configured |
| I32 zxAnOtdrTestParamPrfSeqCodeLen | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.8 | Integer32 | read-create | OTDR test sequence code length. The valid value is the power of two, For example:16,32,64. '0' means not configured. |
| I32 zxAnOtdrTestParamPrfSeqCodeWidth | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.9 | Integer32 | read-create | OTDR test sequence code width. '0' means not configured. |
| ROW zxAnOtdrTestParamPrfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.1.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrTestParamPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrIfTable | 1.3.6.1.4.1.3902.1083.5.2.1.3 | not-accessible | This table includes OTDR test interface information. | |
| zxAnOtdrIfEntry | 1.3.6.1.4.1.3902.1083.5.2.1.3.1 | not-accessible | OTDR interface entry. | |
| STR zxAnOtdrIfAlias | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.5 | DisplayString | read-write | OTDR interface alias. |
| STR zxAnOtdrIfFastTestParamPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.6 | DisplayString | read-write | OTDR fast test parameter profile name list, such as 'DEFAULT_PULSE,DEFAULT_SEQUENCE'. Empty string means unconfigured. |
| STR zxAnOtdrIfRoutineTestParamPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.7 | DisplayString | read-write | OTDR routine test parameter profile name list, such as 'DEFAULT_PULSE,DEFAULT_SEQUENCE'. Empty string means unconfigured. |
| STR zxAnOtdrIfHealthTestParamPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.8 | DisplayString | read-write | OTDR health test parameter profile name list, such as 'DEFAULT_PULSE,DEFAULT_SEQUENCE'. Empty string means unconfigured. |
| STR zxAnOtdrIfReflectorTestParamPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.9 | DisplayString | read-write | OTDR reflector test parameter profile name list, such as 'DEFAULT_REFLECTOR'. |
| STR zxAnOtdrIfNetworkPropertyPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.10 | DisplayString | read-write | OTDR interface network property profile name list. Empty string means unconfigured. |
| STR zxAnOtdrIfAcceptanceTestPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.11 | DisplayString | read-write | OTDR acceptance test parameter profile name list, such as 'DEFAULT_PULSE,DEFAULT_SEQUENCE,DEFAULT_ACCEPTANCE', which are in order of decreasing priority. Empty string means unconfigured. |
| INT zxAnOtdrIfNetworkProperty | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.17 | INTEGER | read-write | The network property of OTDR interface. p2mp(1): the network of point to multi-points. p2p(2): the network of point to point. |
| INT zxAnOtdrIfWorkingStatus | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.18 | INTEGER | read-only | The working status of OTDR interface. |
| INT zxAnOtdrIfUsageStatus | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.19 | INTEGER | read-only | The usage status of OTDR interface. used(1): Health test has been run successfully. unused(2): No test parameter profile is bound to the port and the health test never runs. preconfigured(3): Test parameter profile is bound to the port. reserved(4): The port is reserved by administrator. Test parameter profile cannot be bound to a reserved port and the health test cannot run on it. |
| INT zxAnOtdrIfUsageStatusSwitch | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.20 | INTEGER | read-write | The usage status switch of OTDR interface. An unused status can be switched to reserved, and reserved status can be switched to unused. When get this variable, always return 1. |
| INT zxAnOtdrIfWorkMode | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.21 | INTEGER | read-only | The working mode of OTDR interface. When the mode is faultLocating, the interface can be used for fault locating. When the mode is nodeMonitoring, the interface can be used for node monitoring. When the mode is opticalPowerMonitoring,the interface can be used for optical power monitoring. When the mode is lineDetection, the interface can be used for line detection. When the mode is bothwayTest, the interface can be used for bothway test. Bothway test uses two NEs linked by one fiber. When the mode is unusable, the interface can not be use. |
| STR zxAnOtdrIfBothwayTestPrf | 1.3.6.1.4.1.3902.1083.5.2.1.3.1.22 | DisplayString | read-write | OTDR bothway test parameter profile name list, such as 'DEFAULT_P2P'. Empty string means unconfigured. |
| zxAnOtdrNetPropPrfTable | 1.3.6.1.4.1.3902.1083.5.2.1.4 | not-accessible | OTDR network property profile table. | |
| zxAnOtdrNetPropPrfEntry | 1.3.6.1.4.1.3902.1083.5.2.1.4.1 | not-accessible | OTDR network property profile entry. | |
| STR zxAnOtdrNetPrfName | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.1 | DisplayString | not-accessible | OTDR network property profile name. |
| INT zxAnOtdrNetPrfLinkType | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.2 | INTEGER | read-create | OTDR link type. p2mp(1): the network of point to multi-points. p2p(2): the network of point to point. |
| INT zxAnOtdrNetPrfFirstSplitRatio | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.3 | INTEGER | read-create | OTDR first-level splitting ratio. ratio1-x(20) : first-level splitting ratio is unknown. none(255) : first-level splitting does not exist. |
| INT zxAnOtdrNetPrfSecondSplitRatio | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.4 | INTEGER | read-create | OTDR second-level splitting ratio. ratio1-x(20) : second-level splitting ratio is unknown. none(255) : second-level splitting does not exist. |
| INT zxAnOtdrNetPrfThirdSplitRatio | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.5 | INTEGER | read-create | OTDR third-level splitting ratio. ratio1-x(20) : third-level splitting ratio is unknown. none(255) : third-level splitting does not exist. |
| I32 zxAnOtdrNetPrfLinkLength | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.6 | Integer32 | read-create | OTDR link length. Value 0 means unconfigured. |
| ROW zxAnOtdrNetPrfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.1.4.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrTestParamPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrFastTestObjects | 1.3.6.1.4.1.3902.1083.5.2.2 | |||
| zxAnOtdrFastTestConfObjects | 1.3.6.1.4.1.3902.1083.5.2.2.1 | |||
| zxAnOtdrFastTestActionObjects | 1.3.6.1.4.1.3902.1083.5.2.2.1.1 | |||
| STR zxAnOtdrFastTestSn | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.1 | DisplayString | read-write | OTDR fast test serial number. |
| INT zxAnOtdrFastTestAction | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.2 | INTEGER | read-write | OTDR fast test action. |
| INT zxAnOtdrFastTestMode | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.3 | INTEGER | read-write | OTDR fast test mode. When the mode is pulseMethod, zxAnOtdrFastTestWaveLength, zxAnOtdrFastTestDistance, zxAnOtdrFastTestFiberIor, zxAnOtdrFastTestPulseWidth, zxAnOtdrFastTestDuration are valid. When the mode is sequenceMethod, zxAnOtdrFastTestWaveLength, zxAnOtdrFastTestDistance, zxAnOtdrFastTestFiberIor, zxAnOtdrFastTestDuration, zxAnOtdrFastTestSeqCodeLen, zxAnOtdrFastTestSeqCodeWidth are valid. |
| I32 zxAnOtdrFastTestWaveLength | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.4 | Integer32 | read-write | OTDR fast test wave length. |
| I32 zxAnOtdrFastTestDistance | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.5 | Integer32 | read-write | OTDR fast test distance. |
| I32 zxAnOtdrFastTestFiberIor | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.6 | Integer32 | read-write | OTDR fast test fiber IOR. The range is from 1.4*(10^6) to 1.6*(10^6). |
| I32 zxAnOtdrFastTestPulseWidth | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.7 | Integer32 | read-write | OTDR fast test pulse width. A value less than 200000 is mapped to an integer pulse width value. A value greater than 200000 is mapped to a specific pulse width value. e.g., 5 is mapped to 5ns, 200001 is mapped to 2.5ns. |
| I32 zxAnOtdrFastTestDuration | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.8 | Integer32 | read-write | OTDR fast test duration. |
| I32 zxAnOtdrFastTestSeqCodeLen | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.9 | Integer32 | read-write | OTDR fast test sequence code length. The valid value is the power of two, For example:16,32,64. |
| I32 zxAnOtdrFastTestSeqCodeWidth | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.10 | Integer32 | read-write | OTDR fast test sequence code width. |
| INT zxAnOtdrTestType | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.11 | INTEGER | read-write | OTDR test type. |
| I32 zxAnOtdrFastTestPriority | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.12 | Integer32 | read-write | OTDR fast test priority. |
| INT zxAnOtdrFastTestRequestSource | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.13 | INTEGER | read-write | OTDR fast test request source. |
| IPt zxAnOtdrFastTestRequestSrcIpType | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.14 | InetAddressType | read-write | IP address type of the OTDR fast test request source. |
| IP zxAnOtdrFastTestRequestSrcIp | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.15 | InetAddress | read-write | IP address of the OTDR fast test request source. |
| INT zxAnOtdrMonNodeTestType | 1.3.6.1.4.1.3902.1083.5.2.2.1.1.16 | INTEGER | read-write | OTDR monitoring node test type. |
| zxAnOtdrFastTestIfTable | 1.3.6.1.4.1.3902.1083.5.2.2.1.2 | not-accessible | OTDR fast test interface table. | |
| zxAnOtdrFastTestIfEntry | 1.3.6.1.4.1.3902.1083.5.2.2.1.2.1 | not-accessible | OTDR fast test interface entry. The OTDR fast test consists of two steps, creating fast test ports(zxAnOtdrFastTestIfTable), and then starting fast test(zxAnOtdrFastTestSn, zxAnOtdrFastTestAction). NE restores to a previous state when the erroneous operations are performed. e.g. 1, When creating a port failed, NE needs to delete all the ports of this SN. e.g. 2, When creating ports succeeded, then starting test failed, NE needs to delete all the ports of this SN. | |
| STR zxAnOtdrFastTestIfSn | 1.3.6.1.4.1.3902.1083.5.2.2.1.2.1.1 | DisplayString | not-accessible | OTDR fast test serial number. |
| STR zxAnOtdrAcceptanceTestIfParamPrf | 1.3.6.1.4.1.3902.1083.5.2.2.1.2.1.2 | DisplayString | read-create | OTDR acceptance test parameter profile name list chosen from zxAnOtdrIfAcceptanceTestPrf. e.g. 'DEFAULT-PULSE','DEFAULT-PULSE,DEFAULT-SEQUENCE', 'DEFAULT-PULSE,DEFAULT-SEQUENCE,DEFAULT-ACCEPTANCE'. If zxAnOtdrTestType is not acceptance(7), this should be empty. |
| ROW zxAnOtdrFastTestIfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.2.1.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrFastTestIfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrFastTestStatusObjects | 1.3.6.1.4.1.3902.1083.5.2.2.2 | |||
| zxAnOtdrFastTestStatusGlbObjects | 1.3.6.1.4.1.3902.1083.5.2.2.2.1 | |||
| STR zxAnOtdrFastTestCurrentPort | 1.3.6.1.4.1.3902.1083.5.2.2.2.1.1 | DisplayString | read-only | Current fast testing port index such as '1-1-3-2'. Return empty string means no port is being tested. |
| I32 zxAnOtdrFastTestWaitTestPorts | 1.3.6.1.4.1.3902.1083.5.2.2.2.1.2 | Integer32 | read-only | Current fast test waiting test port number. Return 0 measns no port waiting test. |
| zxAnOtdrFastTestIfStatusTable | 1.3.6.1.4.1.3902.1083.5.2.2.2.2 | not-accessible | OTDR fast test port status table. | |
| zxAnOtdrFastTestIfStatusEntry | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1 | not-accessible | OTDR fast test interface status entry. | |
| INT zxAnOtdrFastTestIfStatus | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.1 | INTEGER | read-only | The result status of OTDR fast test. |
| INT zxAnOtdrFastTestIfFailedReason | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.2 | INTEGER | read-only | The OTDR fast test failed reason. |
| STR zxAnOtdrFastTestIfResultFile | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.3 | DisplayString | read-only | Fast test result file name. NE returns file name such as '1-1-5-1-20120505143302.csv' when the fast test sucess. NE returns empty string when the fast test failed. |
| I32 zxAnOtdrFastTestIfParamPrfs | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.4 | Integer32 | read-only | Number of test parameter profile. |
| I32 zxAnOtdrFastTestIfFinishedPrfs | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.5 | Integer32 | read-only | Number of finished test parameter profile. |
| I32 zxAnOtdrFastTestIfEvalTotalTime | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.6 | Integer32 | read-only | OTDR test estimated total time. |
| I32 zxAnOtdrFastTestIfElapsedTime | 1.3.6.1.4.1.3902.1083.5.2.2.2.2.1.7 | Integer32 | read-only | OTDR test elapsed time. |
| zxAnOtdrFastTestFileFtpObjects | 1.3.6.1.4.1.3902.1083.5.2.2.3 | |||
| zxAnOtdrFileFtpObjects | 1.3.6.1.4.1.3902.1083.5.2.2.3.1 | |||
| IPt zxAnOtdrFileFtpIpAddressType | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.1 | InetAddressType | read-write | IP address type of the FTP server. |
| IP zxAnOtdrFileFtpIpAddress | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.2 | InetAddress | read-write | IP address of the FTP server. |
| INT zxAnOtdrFileFtpProtocolType | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.3 | INTEGER | read-write | Protocol type of the FTP server. ftp(1): File Transfer Protocol. sftp(2): Ssh File Transfer Protocol. |
| STR zxAnOtdrFileFtpUserName | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.4 | DisplayString | read-write | User name of the FTP server. |
| STR zxAnOtdrFileFtpUserPwd | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.5 | DisplayString | read-write | User password of the FTP server. |
| STR zxAnOtdrFileFtpPath | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.6 | DisplayString | read-write | File path which starts from the root directory. |
| STR zxAnOtdrFileFtpFileName | 1.3.6.1.4.1.3902.1083.5.2.2.3.1.7 | DisplayString | read-write | The FTP file name. |
| zxAnOtdrFileFtpUploadStatusTable | 1.3.6.1.4.1.3902.1083.5.2.2.3.2 | not-accessible | OTDR file FTP status table. | |
| zxAnOtdrFileFtpUploadStatusEntry | 1.3.6.1.4.1.3902.1083.5.2.2.3.2.1 | not-accessible | File FTP status entry. | |
| STR zxAnOtdrFileFtpUploadFileName | 1.3.6.1.4.1.3902.1083.5.2.2.3.2.1.1 | DisplayString | not-accessible | OTDR test file name. |
| INT zxAnOtdrFileFtpUploadStatus | 1.3.6.1.4.1.3902.1083.5.2.2.3.2.1.2 | INTEGER | read-only | OTDR FTP status. |
| INT zxAnOtdrFileFtpUploadFailReason | 1.3.6.1.4.1.3902.1083.5.2.2.3.2.1.3 | INTEGER | read-only | OTDR FTP failed reason. |
| zxAnOtdrRoutineTestObjects | 1.3.6.1.4.1.3902.1083.5.2.3 | |||
| zxAnOtdrRoutineTaskIfTable | 1.3.6.1.4.1.3902.1083.5.2.3.2 | not-accessible | OTDR routine task interface table. | |
| zxAnOtdrRoutineTaskIfEntry | 1.3.6.1.4.1.3902.1083.5.2.3.2.1 | not-accessible | OTDR routine task interface entry. The OTDR routine test consists of two steps, creating routine test ports (zxAnOtdrRoutineTaskIfTable), and then configuring routine task (zxAnOtdrRoutineTaskTable). NE restores to a previous state when the erroneous operations are performed. e.g. 1, When creating a port failed, NE needs to delete all the ports of this task. e.g. 2, When creating ports succeeded, then configuring routine task failed, NE needs to delete all the ports of this task. | |
| ROW zxAnOtdrRoutineTaskIfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.3.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrRoutineTaskIfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrRoutineTaskTable | 1.3.6.1.4.1.3902.1083.5.2.3.3 | not-accessible | Routine test task table. | |
| zxAnOtdrRoutineTaskEntry | 1.3.6.1.4.1.3902.1083.5.2.3.3.1 | not-accessible | Routine test task entry. | |
| STR zxAnOtdrRoutineTaskName | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.1 | DisplayString | not-accessible | OTDR routine test task name. |
| DAT zxAnOtdrRoutineTaskStartTime | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.2 | DateAndTime | read-create | The start time of OTDR routine test. For example:yyyy-mm-dd HH:MM:SS.(2013-01-01 00:00:00). |
| I32 zxAnOtdrRoutineTaskInterval | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.3 | Integer32 | read-create | The interval of OTDR routine test. The NE returns 0, when zxAnOtdrRoutineTaskTestMode is sequential test. |
| INT zxAnOtdrRoutineTaskActiveStatus | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.4 | INTEGER | read-create | OTDR routine test task active status. |
| DAT zxAnOtdrRoutineTaskCurrStartTime | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.5 | DateAndTime | read-only | The current routine test task start time. |
| INT zxAnOtdrRoutineTaskOperStatus | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.6 | INTEGER | read-only | OTDR routine test task operational status. |
| INT zxAnOtdrRoutineTaskFailedReason | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.7 | INTEGER | read-only | The OTDR routine test task failed reason. |
| STR zxAnOtdrRoutineTaskResultFile | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.8 | DisplayString | read-only | Routine test result file name. NE returns file name such as 'taskname-20120505143302.zip' when the routine test sucess. NE returns empty string when the routine test failed. |
| INT zxAnOtdrRoutineTaskTestMode | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.9 | INTEGER | read-create | Routine task test mode. |
| ROW zxAnOtdrRoutineTaskRowStatus | 1.3.6.1.4.1.3902.1083.5.2.3.3.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrRoutineTaskEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrRoutineTaskIfStatusTable | 1.3.6.1.4.1.3902.1083.5.2.3.4 | not-accessible | OTDR routine task interface status table | |
| zxAnOtdrRoutineTaskIfStatusEntry | 1.3.6.1.4.1.3902.1083.5.2.3.4.1 | not-accessible | OTDR routine task interface status entry. | |
| INT zxAnOtdrRoutineTaskIfStatus | 1.3.6.1.4.1.3902.1083.5.2.3.4.1.1 | INTEGER | read-only | The result status of OTDR routine test. |
| INT zxAnOtdrRoutineTaskIfFailReason | 1.3.6.1.4.1.3902.1083.5.2.3.4.1.2 | INTEGER | read-only | The OTDR routine test failed reason. |
| zxAnOtdrFtpServerObjects | 1.3.6.1.4.1.3902.1083.5.2.4 | |||
| zxAnOtdrFtpServerTable | 1.3.6.1.4.1.3902.1083.5.2.4.2 | not-accessible | FTP server configuration table. | |
| zxAnOtdrFtpServerEntry | 1.3.6.1.4.1.3902.1083.5.2.4.2.1 | not-accessible | FTP server configuration entry. | |
| STR zxAnOtdrFtpServerId | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.1 | DisplayString | not-accessible | FTP server ID. |
| IPt zxAnOtdrFtpServerIpAddressType | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.2 | InetAddressType | read-create | IP address type of the FTP server. |
| IP zxAnOtdrFtpServerIpAddress | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.3 | InetAddress | read-create | IP address of the FTP server. |
| INT zxAnOtdrFtpServerProtocolType | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.4 | INTEGER | read-create | Protocol type of the FTP server. ftp(1): File Transfer Protocol sftp(2): Ssh File Transfer Protocol |
| STR zxAnOtdrFtpServerUserName | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.5 | DisplayString | read-create | User name of the FTP server. |
| STR zxAnOtdrFtpServerUserPwd | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.6 | DisplayString | read-create | User password of the FTP server. |
| STR zxAnOtdrFtpServerPath | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.7 | DisplayString | read-create | File path which starts from the root directory. |
| ROW zxAnOtdrFtpServerRowStatus | 1.3.6.1.4.1.3902.1083.5.2.4.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrFtpServerEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrAlgorithmObjects | 1.3.6.1.4.1.3902.1083.5.2.5 | |||
| zxAnOtdrAlgorithmTable | 1.3.6.1.4.1.3902.1083.5.2.5.2 | not-accessible | OTDR algorithm table. | |
| zxAnOtdrAlgorithmEntry | 1.3.6.1.4.1.3902.1083.5.2.5.2.1 | not-accessible | OTDR algorithm entry. | |
| I32 zxAnOtdrAlgorithmRack | 1.3.6.1.4.1.3902.1083.5.2.5.2.1.1 | Integer32 | not-accessible | The rack No. of device to be used with OTDR. |
| I32 zxAnOtdrAlgorithmShelf | 1.3.6.1.4.1.3902.1083.5.2.5.2.1.2 | Integer32 | not-accessible | The shelf No. of device to be used with OTDR. |
| I32 zxAnOtdrAlgorithmSlot | 1.3.6.1.4.1.3902.1083.5.2.5.2.1.3 | Integer32 | not-accessible | The slot No. of device to be used with OTDR. |
| STR zxAnOtdrAlgorithmVersion | 1.3.6.1.4.1.3902.1083.5.2.5.2.1.4 | DisplayString | read-only | The OTDR algorithm version of current card. |
| zxAnOtdrTestCapacityObjects | 1.3.6.1.4.1.3902.1083.5.2.6 | |||
| zxAnOtdrTestCapDistanceObjects | 1.3.6.1.4.1.3902.1083.5.2.6.1 | |||
| zxAnOtdrTestCapDistanceGlbObjs | 1.3.6.1.4.1.3902.1083.5.2.6.1.1 | |||
| INT zxAnOtdrTestCapDistanceType | 1.3.6.1.4.1.3902.1083.5.2.6.1.1.1 | INTEGER | read-only | The type of the test capacity distance supported by OTDR. global(1): it means getting maximum-minimum distance by the global objects 'zxAnOtdrTestCapMaxDistance' and 'zxAnOtdrTestCapMinDistance'. pulseWidth(2): it means getting maximum-minimum distance by the table objects 'zxAnOtdrTestCapPwDistanceTable'. |
| I32 zxAnOtdrTestCapMaxDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.1.2 | Integer32 | read-only | The maximum of the global test capacity distance supported by OTDR. |
| I32 zxAnOtdrTestCapMinDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.1.3 | Integer32 | read-only | The minimum of the global test capacity distance supported by OTDR. |
| zxAnOtdrTestCapPwDistanceTable | 1.3.6.1.4.1.3902.1083.5.2.6.1.2 | not-accessible | OTDR test capacity pulse width distance table. | |
| zxAnOtdrTestCapPwDistanceEntry | 1.3.6.1.4.1.3902.1083.5.2.6.1.2.1 | not-accessible | OTDR test capacity pulse width distance entry. | |
| I32 zxAnOtdrTestCapPwDistancePw | 1.3.6.1.4.1.3902.1083.5.2.6.1.2.1.1 | Integer32 | not-accessible | The pulse width supported by OTDR. A value less than 200000 is mapped to an integer pulse width value. A value greater than 200000 is mapped to a specific pulse width value. e.g., 5 is mapped to 5ns, 200001 is mapped to 2.5ns. |
| I32 zxAnOtdrTestCapPwMaxDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.2.1.2 | Integer32 | read-only | The maximum of the test capacity distance supported by the current pulse width. |
| I32 zxAnOtdrTestCapPwMinDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.2.1.3 | Integer32 | read-only | The minimum of the test capacity distance supported by the current pulse width. |
| zxAnOtdrTestCapCwDistanceTable | 1.3.6.1.4.1.3902.1083.5.2.6.1.3 | not-accessible | OTDR test capacity code width distance table. | |
| zxAnOtdrTestCapCwDistanceEntry | 1.3.6.1.4.1.3902.1083.5.2.6.1.3.1 | not-accessible | OTDR test capacity code width distance entry. | |
| I32 zxAnOtdrTestCapCwDistanceCw | 1.3.6.1.4.1.3902.1083.5.2.6.1.3.1.1 | Integer32 | not-accessible | The code width supported by OTDR. |
| I32 zxAnOtdrTestCapCwMaxDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.3.1.2 | Integer32 | read-only | The maximum of the test capacity distance supported by the current code width. |
| I32 zxAnOtdrTestCapCwMinDistance | 1.3.6.1.4.1.3902.1083.5.2.6.1.3.1.3 | Integer32 | read-only | The minimum of the test capacity distance supported by the current code width. |
| zxAnOtdrTestCapDurationObjects | 1.3.6.1.4.1.3902.1083.5.2.6.2 | |||
| zxAnOtdrTestCapDurationGlbObjs | 1.3.6.1.4.1.3902.1083.5.2.6.2.1 | |||
| I32 zxAnOtdrTestCapMaxDuration | 1.3.6.1.4.1.3902.1083.5.2.6.2.1.1 | Integer32 | read-only | The maximum of the test capacity duration supported by OTDR. |
| I32 zxAnOtdrTestCapMinDuration | 1.3.6.1.4.1.3902.1083.5.2.6.2.1.2 | Integer32 | read-only | The minimum of the test capacity duration supported by OTDR. |
| zxAnOtdrTestTaskObjects | 1.3.6.1.4.1.3902.1083.5.2.7 | |||
| zxAnOtdrTestTaskStatusTable | 1.3.6.1.4.1.3902.1083.5.2.7.1 | not-accessible | OTDR test task status table. | |
| zxAnOtdrTestTaskStatusEntry | 1.3.6.1.4.1.3902.1083.5.2.7.1.1 | not-accessible | OTDR test task status entry. | |
| STR zxAnOtdrTestTaskId | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.1 | DisplayString | not-accessible | OTDR test task ID. The task name is zxAnOtdrRoutineTaskName when the zxAnOtdrTestTaskType is routine, other tests relate to zxAnOtdrFastTestSn. |
| INT zxAnOtdrTestTaskStatus | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.2 | INTEGER | read-only | The OTDR test task status. |
| INT zxAnOtdrTestTaskUnexecutedReason | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.3 | INTEGER | read-only | The OTDR test task unexecuted reason. |
| I32 zxAnOtdrTestTaskPriority | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.4 | Integer32 | read-only | The OTDR test task priority. |
| I32 zxAnOtdrTestTaskWaitingTime | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.5 | Integer32 | read-only | The OTDR test task waiting time. When the task is in progress, the waiting time is 0. |
| INT zxAnOtdrTestTaskRequestSource | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.6 | INTEGER | read-only | The OTDR test task request source. |
| INT zxAnOtdrTestTaskType | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.7 | INTEGER | read-only | The task type. fast(1): - Fast test. health(2): - Health database test. adHoc(3): - Ad hoc test. reflector(4): - Reflector test. alarmTrigger(5): - Alarm triggered test. adaptive(6): - Adaptive test. acceptance(7): - Acceptance test. labefaction(8): - Labefaction test. lineDetectionHealth(9): - Line detection health database test. lineDetectionFast(10): - Line detection fast test. bothway(11): - Bothway test. periodicalRoutineTest(50): - Periodical routine test. sequentialRoutineTest(51): - Sequential routine test. |
| DAT zxAnOtdrTestTaskStartTime | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.8 | DateAndTime | read-only | The test task starting time. |
| I32 zxAnOtdrTestTaskRemainTimeout | 1.3.6.1.4.1.3902.1083.5.2.7.1.1.9 | Integer32 | read-only | The OTDR test task remaining timeout. A negative indicates the task should never be timeout. A zero indicates the task has been timeout. |
| zxAnOtdrFastTestTaskConfTable | 1.3.6.1.4.1.3902.1083.5.2.7.2 | not-accessible | OTDR fast test task configuration table. | |
| zxAnOtdrFastTestTaskConfEntry | 1.3.6.1.4.1.3902.1083.5.2.7.2.1 | not-accessible | OTDR fast test task configuration entry. | |
| I32 zxAnOtdrFastTaskConfWaitTimeout | 1.3.6.1.4.1.3902.1083.5.2.7.2.1.1 | Integer32 | read-create | Fast test waiting timeout. The test will be cancelled when timeout. |
| ROW zxAnOtdrFastTaskConfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.7.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrFastTestIfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrMonNodeObjects | 1.3.6.1.4.1.3902.1083.5.2.8 | |||
| zxAnOtdrMonNodeGlobalObjects | 1.3.6.1.4.1.3902.1083.5.2.8.1 | |||
| INT zxAnOtdrMonNodeMonitorStatus | 1.3.6.1.4.1.3902.1083.5.2.8.1.1 | INTEGER | read-only | OTDR node monitoring status. |
| INT zxAnOtdrMonNodeMonitorAction | 1.3.6.1.4.1.3902.1083.5.2.8.1.2 | INTEGER | read-write | OTDR node monitoring action. |
| zxAnOtdrMonNodeConfTable | 1.3.6.1.4.1.3902.1083.5.2.8.2 | not-accessible | OTDR monitoring node configuration table. | |
| zxAnOtdrMonNodeConfEntry | 1.3.6.1.4.1.3902.1083.5.2.8.2.1 | not-accessible | OTDR monitoring node configuration entry. | |
| STR zxAnOtdrMonNodeSn | 1.3.6.1.4.1.3902.1083.5.2.8.2.1.1 | DisplayString | not-accessible | OTDR monitoring node serial number. |
| I32 zxAnOtdrMonNodePosition | 1.3.6.1.4.1.3902.1083.5.2.8.2.1.2 | Integer32 | read-only | OTDR monitoring node position. Value 0 means the monitoring node open/close test is not executed or the test is failed. |
| INT zxAnOtdrMonNodeStatus | 1.3.6.1.4.1.3902.1083.5.2.8.2.1.3 | INTEGER | read-only | OTDR monitoring node status. A zxAnOtdrMonNodeOpenedAlm trap will be sent when the zxAnOtdrMonNodeStatus is opened. A zxAnOtdrMonNodeOpenedClr trap will be sent when the zxAnOtdrMonNodeStatus is closed. |
| ROW zxAnOtdrNodeConfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.8.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrFastTestIfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrMonPortStatusTable | 1.3.6.1.4.1.3902.1083.5.2.8.3 | not-accessible | OTDR monitoring port status table. | |
| zxAnOtdrMonPortStatusEntry | 1.3.6.1.4.1.3902.1083.5.2.8.3.1 | not-accessible | OTDR monitoring port status entry. | |
| INT zxAnOtdrMonPortLinkStatus | 1.3.6.1.4.1.3902.1083.5.2.8.3.1.1 | INTEGER | read-only | OTDR monitoring port link status. A zxAnOtdrMonPortLinkAbnormalAlm trap will be sent when the zxAnOtdrMonPortLinkStatus is abnormal. A zxAnOtdrMonPortLinkAbnormalClr trap will be sent when the zxAnOtdrMonPortLinkStatus is normal. |
| zxAnOtdrMonReflectLabelTable | 1.3.6.1.4.1.3902.1083.5.2.8.4 | not-accessible | OTDR reflector labelling table. | |
| zxAnOtdrMonReflectLabelEntry | 1.3.6.1.4.1.3902.1083.5.2.8.4.1 | not-accessible | OTDR reflector labelling entry. | |
| INT zxAnOtdrMonReflectLabelAction | 1.3.6.1.4.1.3902.1083.5.2.8.4.1.1 | INTEGER | read-write | OTDR reflector labelling action. |
| INT zxAnOtdrMonReflectLabelStatus | 1.3.6.1.4.1.3902.1083.5.2.8.4.1.2 | INTEGER | read-only | OTDR reflector labelling status. |
| DAT zxAnOtdrMonReflectLabelLastTime | 1.3.6.1.4.1.3902.1083.5.2.8.4.1.3 | DateAndTime | read-only | OTDR reflector last labelling time. |
| zxAnOtdrOptModuleMonitorObjects | 1.3.6.1.4.1.3902.1083.5.2.9 | |||
| zxAnOtdrOptModuleGlobalObjects | 1.3.6.1.4.1.3902.1083.5.2.9.1 | |||
| INT zxAnOtdrOptModuleStatus | 1.3.6.1.4.1.3902.1083.5.2.9.1.1 | INTEGER | read-only | The OTDR optical module status. A zxAnOtdrOptModuleAbnormalAlm trap will be sent when the zxAnOtdrOptModuleStatus is abnormal. |
| zxAnOtdrOptModuleIfTable | 1.3.6.1.4.1.3902.1083.5.2.9.2 | not-accessible | OTDR optical module interface table. | |
| zxAnOtdrOptModuleIfEntry | 1.3.6.1.4.1.3902.1083.5.2.9.2.1 | not-accessible | OTDR optical module interface entry. | |
| I32 zxAnOtdrOptModuleIfBasicPwr | 1.3.6.1.4.1.3902.1083.5.2.9.2.1.1 | Integer32 | read-only | OTDR interface basic optical power. '65535' means the basic optical power is invalid. |
| I32 zxAnOtdrOptModuleIfCurrentPwr | 1.3.6.1.4.1.3902.1083.5.2.9.2.1.2 | Integer32 | read-only | OTDR interface current optical power. '65535' means the current optical power is invalid. |
| I32 zxAnOtdrOptModuleIfPwrVaryThresh | 1.3.6.1.4.1.3902.1083.5.2.9.2.1.3 | Integer32 | read-write | OTDR interface optical power variaton threshold. A zxAnOtdrOptPowerVaryExceedAlm trap is sent when the difference value of zxAnOtdrOptModuleIfBasicPwr and zxAnOtdrOptModuleIfCurrentPwr is higher than this threshold. |
| INT zxAnOtdrOptModuleIfPwrAdjust | 1.3.6.1.4.1.3902.1083.5.2.9.2.1.4 | INTEGER | read-write | To adjust the OTDR basic optical power. |
| zxAnOtdrFaultLocateObjects | 1.3.6.1.4.1.3902.1083.5.2.10 | |||
| zxAnOtdrFaultLocateGlobalObjects | 1.3.6.1.4.1.3902.1083.5.2.10.1 | |||
| STR zxAnOtdrGlobalP2mpFaultLocatePrf | 1.3.6.1.4.1.3902.1083.5.2.10.1.1 | DisplayString | read-write | OTDR global P2MP fault locating threshold profile name. The global profile is applied to the interface when the interface fault locating profile is unconfigured. |
| STR zxAnOtdrGlobalP2pFaultLocatePrf | 1.3.6.1.4.1.3902.1083.5.2.10.1.2 | DisplayString | read-write | OTDR global P2P fault locating threshold profile name. The global profile is applied to the interface when the interface fault locating profile is unconfigured. |
| zxAnOtdrP2mpFaultLocatePrfTable | 1.3.6.1.4.1.3902.1083.5.2.10.2 | not-accessible | OTDR P2MP fault locating threshold profile table. | |
| zxAnOtdrP2mpFaultLocatePrfEntry | 1.3.6.1.4.1.3902.1083.5.2.10.2.1 | not-accessible | OTDR P2MP fault locating threshold profile entry. | |
| STR zxAnOtdrP2mpFaultLocatePrfName | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.1 | DisplayString | not-accessible | OTDR P2MP fault locating threshold profile name. |
| I32 zxAnOtdrP2mpPositionDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.2 | Integer32 | read-create | OTDR P2MP position difference threshold. |
| I32 zxAnOtdrP2mpTrunkBrokenLossDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.3 | Integer32 | read-create | OTDR P2MP trunk broken insertion loss difference threshold. This threshold is used to locate trunk broken fault. |
| I32 zxAnOtdrP2mpTrunkBrokenLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.4 | Integer32 | read-create | OTDR P2MP trunk broken insertion loss threshold. This threshold is used to locate trunk broken fault. |
| I32 zxAnOtdrP2mpTrunkAttenLossDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.5 | Integer32 | read-create | OTDR P2MP trunk attenuation insertion loss difference threshold. This threshold is used to locate trunk attenuation fault. |
| I32 zxAnOtdrP2mpTrunkAttenLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.6 | Integer32 | read-create | OTDR P2MP trunk attenuation insertion loss threshold. This threshold is used to locate trunk attenuation fault. |
| I32 zxAnOtdrP2mpTrunkAbnPeakDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.7 | Integer32 | read-create | OTDR P2MP trunk abnormal reflective peak difference threshold. This threshold is used to locate trunk abnormal fault. |
| I32 zxAnOtdrP2mpTrunkAbnRtnLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.8 | Integer32 | read-create | OTDR P2MP trunk abnormal return loss threshold. This threshold is used to locate trunk abnormal fault. |
| I32 zxAnOtdrP2mpTrunkAbnLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.9 | Integer32 | read-create | OTDR P2MP trunk abnormal insertion loss threshold. This threshold is used to locate trunk abnormal fault. |
| I32 zxAnOtdrP2mpBranchBrokenRtnLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.10 | Integer32 | read-create | OTDR P2MP branch broken return loss threshold. This threshold is used to locate branch broken fault. |
| I32 zxAnOtdrP2mpBranchBrokenLoss | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.11 | Integer32 | read-create | OTDR P2MP branch broken insertion loss threshold. This threshold is used to locate branch broken fault. |
| I32 zxAnOtdrP2mpBranchBrokenPeakDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.12 | Integer32 | read-create | OTDR P2MP branch broken reflective peak difference threshold. This threshold is used to locate branch broken fault. |
| I32 zxAnOtdrP2mpBranchAbnPeakDiff | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.13 | Integer32 | read-create | OTDR P2MP branch abnormal reflective peak difference threshold. This threshold is used to locate branch abnormal fault. |
| ROW zxAnOtdrP2mpFaultLocPrfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.10.2.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrTestParamPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrP2pFaultLocatePrfTable | 1.3.6.1.4.1.3902.1083.5.2.10.3 | not-accessible | OTDR P2P fault locating threshold profile table. | |
| zxAnOtdrP2pFaultLocatePrfEntry | 1.3.6.1.4.1.3902.1083.5.2.10.3.1 | not-accessible | OTDR P2P fault locating threshold profile entry. | |
| STR zxAnOtdrP2pFaultLocatePrfName | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.1 | DisplayString | not-accessible | OTDR P2P fault locating threshold profile name. |
| I32 zxAnOtdrP2pPositionDiff | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.2 | Integer32 | read-create | OTDR P2P position difference threshold. |
| I32 zxAnOtdrP2pBrokenLossDiff | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.3 | Integer32 | read-create | OTDR P2P link broken insertion loss difference threshold. This threshold is used to locate link broken fault. |
| I32 zxAnOtdrP2pBrokenLoss | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.4 | Integer32 | read-create | OTDR P2P link broken insertion loss threshold. This threshold is used to locate link broken fault. |
| I32 zxAnOtdrP2pAttenuationLossDiff | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.5 | Integer32 | read-create | OTDR P2P link attenuation insertion loss difference threshold. This threshold is used to locate link attenuation fault. |
| I32 zxAnOtdrP2pAttenuationLoss | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.6 | Integer32 | read-create | OTDR P2P link attenuation insertion loss threshold. This threshold is used to locate link attenuation fault. |
| I32 zxAnOtdrP2pAbnormalPeakDiff | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.7 | Integer32 | read-create | OTDR P2P link abnormal reflective peak difference threshold. This threshold is used to locate link abnormal fault. |
| I32 zxAnOtdrP2pAbnormalReturnLoss | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.8 | Integer32 | read-create | OTDR P2P link abnormal return loss threshold. This threshold is used to locate link abnormal fault. |
| I32 zxAnOtdrP2pAbnormalLoss | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.9 | Integer32 | read-create | OTDR P2P link abnormal insertion loss threshold. This threshold is used to locate link abnormal fault. |
| ROW zxAnOtdrP2pFaultLocPrfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.10.3.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrTestParamPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrFaultLocateIfConfTable | 1.3.6.1.4.1.3902.1083.5.2.10.4 | not-accessible | OTDR interface fault locating threshold profile table. | |
| zxAnOtdrFaultLocateIfConfEntry | 1.3.6.1.4.1.3902.1083.5.2.10.4.1 | not-accessible | OTDR interface fault locating threshold profile entry. | |
| STR zxAnOtdrFaultLocateIfP2mpPrf | 1.3.6.1.4.1.3902.1083.5.2.10.4.1.1 | DisplayString | read-create | OTDR fault locating P2MP threshold profile name. Empty string means unconfigured. |
| STR zxAnOtdrFaultLocateIfP2pPrf | 1.3.6.1.4.1.3902.1083.5.2.10.4.1.2 | DisplayString | read-create | OTDR fault locating P2P threshold profile name. Empty string means unconfigured. |
| ROW zxAnOtdrFaultLocateIfRowStatus | 1.3.6.1.4.1.3902.1083.5.2.10.4.1.50 | RowStatus | read-create | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnOtdrTestParamPrfEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1). |
| zxAnOtdrEventObjects | 1.3.6.1.4.1.3902.1083.5.2.11 | |||
| zxAnOtdrIfEventBatchConfTable | 1.3.6.1.4.1.3902.1083.5.2.11.2 | not-accessible | OTDR interface event batch configuration table. | |
| zxAnOtdrIfEventBatchConfEntry | 1.3.6.1.4.1.3902.1083.5.2.11.2.1 | not-accessible | OTDR interface event batch configuration entry. | |
| STR zxAnOtdrIfEventBatchConfDevTypes | 1.3.6.1.4.1.3902.1083.5.2.11.2.1.1 | DisplayString | read-write | OTDR interface event device type list. The format of the value is as follows: '1:3-6,10;2:2,8'. It means that the device type value of the event ID including 3,4,5,6,10 is 1 and the device type value of the event ID including 2,8 is 2. It will return the empty string when reading this object. |
| zxAnOtdrIfEventConfTable | 1.3.6.1.4.1.3902.1083.5.2.11.3 | not-accessible | OTDR interface event configuration table. | |
| zxAnOtdrIfEventConfEntry | 1.3.6.1.4.1.3902.1083.5.2.11.3.1 | not-accessible | OTDR interface event configuration entry. | |
| I32 zxAnOtdrIfEventConfEventId | 1.3.6.1.4.1.3902.1083.5.2.11.3.1.1 | Integer32 | not-accessible | OTDR interface event ID. |
| I32 zxAnOtdrIfEventConfDevType | 1.3.6.1.4.1.3902.1083.5.2.11.3.1.2 | Integer32 | read-write | OTDR interface event device type. Value 0 means the event device type is empty. |
| STR zxAnOtdrIfEventConfDevDesc | 1.3.6.1.4.1.3902.1083.5.2.11.3.1.3 | DisplayString | read-write | OTDR interface event device description. |
| zxAnOtdrAdaptiveTestObjects | 1.3.6.1.4.1.3902.1083.5.2.12 | |||
| zxAnOtdrAdaptiveTestLinkObjects | 1.3.6.1.4.1.3902.1083.5.2.12.2 | |||
| zxAnOtdrAdaptTestLinkGlbObjects | 1.3.6.1.4.1.3902.1083.5.2.12.2.1 | |||
| I32 zxAnOtdrATLinkLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.2.1.2 | Integer32 | read-write | The global link loss threshold of the OTDR adaptive test. This global threshold is applied to the interface when the zxAnOtdrATLinkIfParamType is global(1). |
| I32 zxAnOtdrATLinkRtnLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.2.1.3 | Integer32 | read-write | The global link return loss threshold of the OTDR adaptive test. This global threshold is applied to the interface when the zxAnOtdrATLinkIfParamType is global(1). |
| zxAnOtdrAdaptTestLinkIfConfTable | 1.3.6.1.4.1.3902.1083.5.2.12.2.2 | not-accessible | OTDR adaptive test link threshold interface configuration table. | |
| zxAnOtdrAdaptTestLinkIfConfEntry | 1.3.6.1.4.1.3902.1083.5.2.12.2.2.1 | not-accessible | OTDR adaptive test link threshold interface configuration entry. | |
| INT zxAnOtdrATLinkIfParamType | 1.3.6.1.4.1.3902.1083.5.2.12.2.2.1.1 | INTEGER | read-write | The link parameters type of the OTDR adaptive test. |
| I32 zxAnOtdrATLinkIfLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.2.2.1.2 | Integer32 | read-write | The link loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATLinkIfParamType is userDefined(2). |
| I32 zxAnOtdrATLinkIfRtnLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.2.2.1.3 | Integer32 | read-write | The link return loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATLinkIfParamType is userDefined(2). |
| zxAnOtdrAdaptiveTestDevObjects | 1.3.6.1.4.1.3902.1083.5.2.12.3 | |||
| zxAnOtdrAdaptTestDevGlbObjects | 1.3.6.1.4.1.3902.1083.5.2.12.3.1 | |||
| I32 zxAnOtdrATDevFiberAttenThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.2 | Integer32 | read-write | The global device fiber attenuation threshold of the OTDR adaptive test. This global threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.3 | Integer32 | read-write | The global device loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.4 | Integer32 | read-write | The global device reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevConnLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.5 | Integer32 | read-write | The global device connector loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevConnReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.6 | Integer32 | read-write | The global device connector reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSpliceLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.7 | Integer32 | read-write | The global device splice loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSpReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.8 | Integer32 | read-write | The global device splitter reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp2LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.9 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:2 or 2:2) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp4LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.10 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:4 or 2:4) loss threshold of the the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp8LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.11 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:8 or 2:8) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp16LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.12 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:16 or 2:16) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp32LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.13 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:32 or 2:32) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp64LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.14 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:64 or 2:64) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevSp128LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.15 | Integer32 | read-write | The global device splitter (the splitting ratio is 1:128 or 2:128) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| I32 zxAnOtdrATDevOnuReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.1.16 | Integer32 | read-write | The global device ONU reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is global(1). |
| zxAnOtdrAdaptTestDevIfConfTable | 1.3.6.1.4.1.3902.1083.5.2.12.3.2 | not-accessible | OTDR adaptive test device threshold interface configuration table. | |
| zxAnOtdrAdaptTestDevIfConfEntry | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1 | not-accessible | OTDR adaptive test device threshold interface configuration evntry. | |
| INT zxAnOtdrATDevIfParamType | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.1 | INTEGER | read-write | The device parameters type of the OTDR adaptive test. |
| I32 zxAnOtdrATDevIfFiberAttenThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.2 | Integer32 | read-write | The device fiber attenuation threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.3 | Integer32 | read-write | The device loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.4 | Integer32 | read-write | The device reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfConnLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.5 | Integer32 | read-write | The device connector loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfConnReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.6 | Integer32 | read-write | The device connector reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSpliceLossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.7 | Integer32 | read-write | The device splice loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSpReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.8 | Integer32 | read-write | The device splitter reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp2LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.9 | Integer32 | read-write | The device splitter (the splitting ratio is 1:2 or 2:2) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp4LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.10 | Integer32 | read-write | The device splitter (the splitting ratio is 1:4 or 2:4) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp8LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.11 | Integer32 | read-write | The device splitter (the splitting ratio is 1:8 or 2:8) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp16LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.12 | Integer32 | read-write | The device splitter (the splitting ratio is 1:16 or 2:16) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp32LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.13 | Integer32 | read-write | The device splitter (the splitting ratio is 1:32 or 2:32) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp64LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.14 | Integer32 | read-write | The device splitter (the splitting ratio is 1:64 or 2:64) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfSp128LossThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.15 | Integer32 | read-write | The device splitter (the splitting ratio is 1:128 or 2:128) loss threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| I32 zxAnOtdrATDevIfOnuReflThresh | 1.3.6.1.4.1.3902.1083.5.2.12.3.2.1.16 | Integer32 | read-write | The device ONU reflectivity threshold of the OTDR adaptive test. This threshold is applied to the interface when the zxAnOtdrATDevIfParamType is userDefined(2). |
| zxAnOtdrDetectionLineObjects | 1.3.6.1.4.1.3902.1083.5.2.13 | |||
| zxAnOtdrDetectionLineConfTable | 1.3.6.1.4.1.3902.1083.5.2.13.2 | not-accessible | OTDR detection line configuration table. | |
| zxAnOtdrDetectionLineConfEntry | 1.3.6.1.4.1.3902.1083.5.2.13.2.1 | not-accessible | OTDR detection line configuration entry. | |
| I32 zxAnOtdrDetectLineId | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.1 | Integer32 | not-accessible | OTDR detection line ID. |
| I32 zxAnOtdrDetectLineLength | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.2 | Integer32 | read-only | OTDR detection line length. |
| STR zxAnOtdrDetectLineAlias | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.3 | DisplayString | read-write | OTDR detection line alias. |
| I32 zxAnOtdrDetectLinePositionDiff | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.4 | Integer32 | read-write | OTDR detection line position difference threshold. |
| I32 zxAnOtdrDetectLineAbnPeakDiff | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.5 | Integer32 | read-write | OTDR detection line abnormal reflective peak difference threshold. |
| INT zxAnOtdrDetectLineStatus | 1.3.6.1.4.1.3902.1083.5.2.13.2.1.6 | INTEGER | read-only | OTDR detection line status. A zxAnOtdrDetectionLineAbnAlm trap will be sent when the zxAnOtdrDetectionLineStatus is peakAbnormal or fiberBroken. A zxAnOtdrDetectionLineAbnClr trap will be sent when the zxAnOtdrDetectionLineStatus is normal. |
| zxAnOtdrNotifications | 1.3.6.1.4.1.3902.1083.5.3 | |||
| NTF zxAnOtdrRoutineTaskFinished | 1.3.6.1.4.1.3902.1083.5.3.1 | A zxAnOtdrRoutineTaskFinished is sent when the agent has detected that the OTDR routine test task finished. | ||
| NTF zxAnOtdrPortTestFinished | 1.3.6.1.4.1.3902.1083.5.3.2 | A zxAnOtdrPortTestFinished is sent when the agent has detected that the OTDR port test finished. | ||
| zxAnOtdrEnvTraps | 1.3.6.1.4.1.3902.1083.5.3.50 | |||
| NTF zxAnOtdrEnvCtrlCardHighTempAlm | 1.3.6.1.4.1.3902.1083.5.3.50.1 | A zxAnOtdrEnvCtrlCardHighTempAlm trap is sent when the current control card temperature is higher than zxAnOtdrCtrlCardTempHighThresh. | ||
| NTF zxAnOtdrEnvCtrlCardHighTempClr | 1.3.6.1.4.1.3902.1083.5.3.50.2 | A zxAnOtdrEnvCtrlCardHighTempClr trap is sent when the current control card temperature is lower than zxAnOtdrCtrlCardTempHighThresh. | ||
| NTF zxAnOtdrEnvCtrlCardLowTempAlm | 1.3.6.1.4.1.3902.1083.5.3.50.3 | A zxAnOtdrEnvCtrlCardLowTempAlm trap is sent when the current control card temperature is lower than zxAnOtdrCtrlCardTempLowThresh. | ||
| NTF zxAnOtdrEnvCtrlCardLowTempClr | 1.3.6.1.4.1.3902.1083.5.3.50.4 | A zxAnOtdrEnvCtrlCardLowTempClr trap is sent when the current control card temperature is higher than zxAnOtdrCtrlCardTempLowThresh. | ||
| NTF zxAnOtdrEnvFanFailureAlm | 1.3.6.1.4.1.3902.1083.5.3.50.5 | A zxAnOtdrEnvFanFailureAlm trap is sent when the zxAnOtdrEnvFanStatus is abnormal. | ||
| NTF zxAnOtdrEnvFanFailureClr | 1.3.6.1.4.1.3902.1083.5.3.50.6 | A zxAnOtdrEnvFanFailureClr trap is sent when the zxAnOtdrEnvFanStatus is normal. | ||
| NTF zxAnOtdrEnvApdHighTempAlm | 1.3.6.1.4.1.3902.1083.5.3.50.7 | A zxAnOtdrEnvApdHighTempAlm trap is sent when the APD current temperature is higher than zxAnOtdrEnvApdTempHighThresh. | ||
| NTF zxAnOtdrEnvApdHighTempClr | 1.3.6.1.4.1.3902.1083.5.3.50.8 | A zxAnOtdrEnvApdHighTempClr trap is sent when the APD current temperature is lower than zxAnOtdrEnvApdTempHighThresh. | ||
| NTF zxAnOtdrEnvApdLowTempAlm | 1.3.6.1.4.1.3902.1083.5.3.50.9 | A zxAnOtdrEnvApdLowTempAlm trap is sent when the APD current temperature is lower than zxAnOtdrEnvApdTempLowThresh. | ||
| NTF zxAnOtdrEnvApdLowTempClr | 1.3.6.1.4.1.3902.1083.5.3.50.10 | A zxAnOtdrEnvApdLowTempClr trap is sent when the APD current temperature is higher than zxAnOtdrEnvApdTempLowThresh. | ||
| NTF zxAnOtdrPortUtilExceedAlm | 1.3.6.1.4.1.3902.1083.5.3.50.11 | A zxAnOtdrPortUtilExceedAlm trap is sent when the current port utilization is higher than zxAnOtdrPortUtilizationThresh. | ||
| NTF zxAnOtdrPortUtilExceedClr | 1.3.6.1.4.1.3902.1083.5.3.50.12 | A zxAnOtdrPortUtilExceedClr trap is sent when the current port utilization is lower than zxAnOtdrPortUtilizationThresh. | ||
| zxAnOtdrMonNodeTraps | 1.3.6.1.4.1.3902.1083.5.3.51 | |||
| NTF zxAnOtdrMonNodeOpenedAlm | 1.3.6.1.4.1.3902.1083.5.3.51.1 | A zxAnOtdrMonNodeOpenedAlm trap is sent when the zxAnOtdrMonNodeStatus is opened. | ||
| NTF zxAnOtdrMonNodeOpenedClr | 1.3.6.1.4.1.3902.1083.5.3.51.2 | A zxAnOtdrMonNodeOpenedClr trap is sent when the zxAnOtdrMonNodeStatus is closed. | ||
| NTF zxAnOtdrMonPortLinkAbnormalAlm | 1.3.6.1.4.1.3902.1083.5.3.51.3 | A zxAnOtdrMonPortLinkAbnormalAlm trap is sent when the zxAnOtdrMonPortLinkStatus is abnormal. | ||
| NTF zxAnOtdrMonPortLinkAbnormalClr | 1.3.6.1.4.1.3902.1083.5.3.51.4 | A zxAnOtdrMonPortLinkAbnormalClr trap is sent when the zxAnOtdrMonPortLinkStatus is normal. | ||
| zxAnOtdrOptModuleMonitorTraps | 1.3.6.1.4.1.3902.1083.5.3.52 | |||
| NTF zxAnOtdrOptModuleAbnormalAlm | 1.3.6.1.4.1.3902.1083.5.3.52.1 | A zxAnOtdrOptModuleAbnormalAlm is sent when the zxAnOtdrOptModuleStatus is abnormal. | ||
| NTF zxAnOtdrOptModuleAbnormalClr | 1.3.6.1.4.1.3902.1083.5.3.52.2 | A zxAnOtdrOptModuleAbnormalClr is sent when the zxAnOtdrOptModuleStatus is normal. | ||
| NTF zxAnOtdrOptPowerVaryExceedAlm | 1.3.6.1.4.1.3902.1083.5.3.52.3 | A zxAnOtdrOptPowerVaryExceedAlm trap is sent when the difference value of zxAnOtdrOptModuleIfBasicPwr and zxAnOtdrOptModuleIfCurrentPwr is higher than zxAnOtdrOptModuleIfPwrVaryThresh. | ||
| NTF zxAnOtdrOptPowerVaryExceedClr | 1.3.6.1.4.1.3902.1083.5.3.52.4 | A zxAnOtdrOptPowerVaryExceedClr trap is sent when the difference value of zxAnOtdrOptModuleIfBasicPwr and zxAnOtdrOptModuleIfCurrentPwr is lower than zxAnOtdrOptModuleIfPwrVaryThresh. | ||
| zxAnOtdrDetectionLineTraps | 1.3.6.1.4.1.3902.1083.5.3.53 | |||
| NTF zxAnOtdrDetectionLineAbnAlm | 1.3.6.1.4.1.3902.1083.5.3.53.1 | A zxAnOtdrDetectionLineAbnAlm is sent when the zxAnOtdrDetectionLineStatus is peakAbnormal or brokenFiber. | ||
| NTF zxAnOtdrDetectionLineAbnClr | 1.3.6.1.4.1.3902.1083.5.3.53.2 | A zxAnOtdrDetectionAbnClr is sent when the zxAnOtdrDetectionLineStatus is normal. |
RFC description
OTDR (Optical Time Domain Reflectometer) equipment management on ZTE networks. Manages test configuration, tasks, and fiber diagnostics.
Start monitoring ZTE Access Node (PON/fiber interfaces with integrated OTDR) (fiber-fault-distance/loss test-result status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.