All MIBs › XYPLEX-SYSTEM-MIB
Category: Xylogics and Xyplex Terminal Servers
Description: Monitors Xyplex system-level objects including hardware status, software version, and resource utilization.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is XYPLEX-SYSTEM-MIB?
XYPLEX-SYSTEM-MIB MIB is a legacy vendor MIB from Xyplex (a terminal server/network access equipment maker later part of iTouch/MRV) covering system-level management objects for its devices. Based on its stated purpose it reports hardware status, software version, and resource utilization for the device. This places clear emphasis on monitoring both hardware health and software identification — tracking whether onboard hardware components are functioning correctly, confirming the running firmware/software version, and observing resource usage (such as memory or CPU) that might indicate an overloaded unit. As a proprietary system MIB it likely stands largely on its own, though it may share conventions with Xyplex's broader terminal-server MIB family. It would have been deployed on Xyplex terminal servers and network access units in legacy enterprise dial-up/terminal networking environments.
IPNetwork Monitor allows you to monitor SNMP objects defined in XYPLEX-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Xyplex terminal servers/network access equipment
Monitoring Examples
No concrete object or table names were supplied for this module, so a specific polling example cannot be grounded in real object names; based on the stated purpose, likely candidates would be hardware-status, software-version, and resource-utilization objects, but this cannot be confirmed without the underlying object list.
What Can Be Monitored
- hardware status
- software version
- resource utilization (CPU/memory)
This MIB depends on
Related MIBs
Imported Objects
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1212
| OBJECT-TYPE |
From RFC1213-MIB
| DisplayString |
| TRAP-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| bootControl | 1.3.6.1.4.1.33.1.34 | |||
| INT bootControlDumpBootpTftp | 1.3.6.1.4.1.33.1.34.10 | INTEGER | read-write | Control for dumping via the combination of BOOTP and TFTP. Corresponds to SERVER DUMP PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpLocal | 1.3.6.1.4.1.33.1.34.11 | INTEGER | read-write | Control for dumping to a local medium. Corresponds to SERVER DUMP PROTOCOL LOCAL and the presence of 'Local' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpMop | 1.3.6.1.4.1.33.1.34.12 | INTEGER | read-write | Control for dumping via DEC MOP. Corresponds to SERVER DUMP PROTOCOL MOP and the presence of 'MOP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpProprietary | 1.3.6.1.4.1.33.1.34.13 | INTEGER | read-write | Control for dumping via Xyplex-proprietary extended MOP. Corresponds to SERVER DUMP PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpRarpTftp | 1.3.6.1.4.1.33.1.34.14 | INTEGER | read-write | Control for dumping via the combination of RARP and TFTP. Corresponds to SERVER DUMP PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadBootpTftp | 1.3.6.1.4.1.33.1.34.4 | INTEGER | read-write | Control for loading via the combination of BOOTP and TFTP. Corresponds to SERVER LOAD PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP/' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| STR bootControlLoadInternetFile | 1.3.6.1.4.1.33.1.34.1 | DisplayString | read-write | The filename to request when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD FILE and the value labeled 'Internet Load File:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetGateway | 1.3.6.1.4.1.33.1.34.3 | IpAddress | read-write | The internet address of the gateway to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD GATEWAY and the value labeled 'Internet Load Gateway:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetServer | 1.3.6.1.4.1.33.1.34.2 | IpAddress | read-write | The internet address of the server to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD HOST and the value labeled 'Internet Load Host:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadLocal | 1.3.6.1.4.1.33.1.34.6 | INTEGER | read-write | Control for loading from a local medium. Corresponds to SERVER LOAD PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadMop | 1.3.6.1.4.1.33.1.34.7 | INTEGER | read-write | Control for loading via DEC MOP. Corresponds to SERVER LOAD PROTOCOL MOP and the presence of 'MOP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadProprietary | 1.3.6.1.4.1.33.1.34.8 | INTEGER | read-write | Control for loading via Xyplex-proprietary extended MOP. Corresponds to SERVER LOAD PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadRarpTftp | 1.3.6.1.4.1.33.1.34.9 | INTEGER | read-write | Control for loading via the combination of RARP and TFTP. Corresponds to SERVER LOAD PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadTftpDirect | 1.3.6.1.4.1.33.1.34.5 | INTEGER | read-write | Control for loading via directed TFTP. Corresponds to SERVER LOAD PROTOCOL TFTPDIRECT and the presence of 'TFTPDIRECT' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamBootpTftp | 1.3.6.1.4.1.33.1.34.15 | INTEGER | read-write | Control for loading parameters via the combination of BOOTP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'BOOTP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamLocal | 1.3.6.1.4.1.33.1.34.16 | INTEGER | read-write | Control for loading parameters from a local medium. Corresponds to SERVER PARAMETER PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamMop | 1.3.6.1.4.1.33.1.34.17 | INTEGER | read-write | Control for loading parameters via DEC MOP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'MOP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamProprietary | 1.3.6.1.4.1.33.1.34.18 | INTEGER | read-write | Control for loading parameters via Xyplex-proprietary extended MOP. Corresponds to SERVER PARAMETER PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamRarpTftp | 1.3.6.1.4.1.33.1.34.19 | INTEGER | read-write | Control for loading parameters via the combination of RARP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| featEntry | 1.3.6.1.4.1.33.1.33.1 | not-accessible | Status values for a system feature. | |
| INT featStatus | 1.3.6.1.4.1.33.1.33.1.2 | INTEGER | read-write | The status of the feature as of the next system initialization. Corresponds to the presence of the feature's lable following the label 'Enabled Feature(s): in the UNIT display. |
| featTable | 1.3.6.1.4.1.33.1.33 | not-accessible | A list of feature entries. The number of entries is given by the value of sysFeatureNumber. | |
| INT featType | 1.3.6.1.4.1.33.1.33.1.1 | INTEGER | read-only | Identification of a feature type. Corresponds to a SERVER feature keyword. |
| INT resAdminMaximum | 1.3.6.1.4.1.33.1.32.1.4 | INTEGER | read-write | The desired maximum possible number of resources in the system. In many cases, ACCESS to this object for a particular resType is read-only. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for desired, administrative values. When the desired change takes effect is implementation specific, ranging from immediately to the next system initialization. |
| GAU resCurrent | 1.3.6.1.4.1.33.1.32.1.2 | Gauge | read-only | The number of resources currently in use on the system. Typically corresponds directly to a value labeled 'Cur' in the SERVER ALTERNATE STATUS display. |
| resEntry | 1.3.6.1.4.1.33.1.32.1 | not-accessible | Status values for a system resource. | |
| CTR resLacks | 1.3.6.1.4.1.33.1.32.1.5 | Counter | read-only | The number of times since system initialization that the system could not obtain the resource because none were available. Typically corresponds directly to a value labeled 'Failure' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns zero for this object. |
| DAT resLackTime | 1.3.6.1.4.1.33.1.32.1.6 | DateTime | read-only | The local system date and time when resLack last increased. Typically corresponds directly to a value labeled 'Last Occurred' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns all zeroes (unknown) for this object. |
| INT resOperMaximum | 1.3.6.1.4.1.33.1.32.1.7 | INTEGER | read-only | The current maximum possible number of resources in the system. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for current operational values. This value is based on current or previous value of resAdminMaximum. |
| NTF resourceLack | 1.3.6.1.4.1.33.1.0.1 | Indication that the system incremented the corresponding value of resLacks. | ||
| resTable | 1.3.6.1.4.1.33.1.32 | not-accessible | A list of resource entries. The number of entries is given by the value of sysResourceNumber. | |
| INT resType | 1.3.6.1.4.1.33.1.32.1.1 | INTEGER | read-only | Identification of a resource type. Typically corresponds directly to a label such as 'Processes:' in the SERVER ALTERNATE STATUS display. |
| GAU resWorst | 1.3.6.1.4.1.33.1.32.1.3 | Gauge | read-only | The highest or lowest value of resCurrent since system initialization. Typically corresponds directly to a value labeled 'High' or 'Low' in the SERVER ALTERNATE STATUS display. |
| CTR sysChassisFaultTransitions | 1.3.6.1.4.1.33.1.29 | Counter | read-only | The number of times this system has seen sysChassisState switch from 'noFault' to 'fault' or from 'fault' to 'noFault'. Corresponds directly to the value labeled 'Crate Transition Count: in the SERVER ALTERNATE STATUS display. |
| INT sysChassisState | 1.3.6.1.4.1.33.1.28 | INTEGER | read-only | For chassis-based systems, the state of the overall chassis. 'notApplicable' indicates the system is not chassis based. 'noFault' indicates no current chassis problem. 'fault' indicates a current chassis problem such as a card or power supply failure. Corresponds directly to the value labeled 'Crate Current State: in the SERVER ALTERNATE STATUS display. |
| INT sysChassisType | 1.3.6.1.4.1.33.1.14 | INTEGER | read-only | The type of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysChassisVersion | 1.3.6.1.4.1.33.1.15 | INTEGER | read-only | This version of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysCrash | 1.3.6.1.4.1.33.1.16 | INTEGER | read-write | Control to cause this system to crash. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes an immediate crash. Corresponds to the CRASH command. |
| DAT sysDateTime | 1.3.6.1.4.1.33.1.3 | DateTime | read-write | The system's current local date and time. Corresponds directly to SERVER DATE and SERVER TIME and the value in various displays. |
| INT sysDefineMode | 1.3.6.1.4.1.33.1.2 | INTEGER | read-write | The system's operation with regard to DEFINE commands. 'permOnly' indicates that DEFINE commands modify only the permanent data base. 'operAndPerm' indicates that DEFINE commands modify both operational and permanent data bases, unless specifically documented to the contrary. Corresponds to SERVER CHANGE and the presence of the label CHANGE in the SERVER CHARACTERISTICS display. |
| INT sysDump | 1.3.6.1.4.1.33.1.6 | INTEGER | read-write | Control for dumping the system's memory when the system crashes. Corresponds directly to SERVER DUMP and the presence of 'Dump' under the label 'Enabled Characteristics' in the SERVER CHARACTERISTICS display. |
| OCT sysDumperAddress | 1.3.6.1.4.1.33.1.26 | OCTET STRING | read-only | The network address of the system that most recently accepted a crash dump from this system. Corresponds directly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| ADR sysDumperAddressType | 1.3.6.1.4.1.33.1.25 | AddressType | read-only | The type of network address contained in sysDumperAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's was dumped to local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| INT sysFeatureNumber | 1.3.6.1.4.1.33.1.31 | INTEGER | read-only | The number of feature entries in the Feature table. |
| INT sysHardwareType | 1.3.6.1.4.1.33.1.12 | INTEGER | read-only | The type of hardware on which the system is running, with values as defined in Xyplex Assigned Numbers, Xyplex document number 420-0497. Corresponds directly to the value labeled 'Hardware Type:' in the UNIT display. |
| INT sysHardwareVersion | 1.3.6.1.4.1.33.1.13 | INTEGER | read-only | This version of hardware on which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| STR sysIdent | 1.3.6.1.4.1.33.1.1 | DisplayString | read-write | An identification string for local and remote displays. Corresponds directly to SERVER IDENTIFICATION and the value labeled 'Identification:' on the SERVER CHARACTERISTICS display. |
| INT sysInitialize | 1.3.6.1.4.1.33.1.17 | INTEGER | read-write | Control to cause this system to reset its software to initial load values, typically by reloading. When executing an initialize command, the system observes the value of sysInitializeDelay as supplied anywhere in the same set request with sysInitialize. If this value is not included in the set request, the system uses its default value. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'conditionalExecute' causes initialization if the overall system state is acceptible (such as not needing to store permanent parameters). Setting it to 'unconditionalExecute' causes initialization regardless of the overall system state. Setting it to 'cancel' aborts an initialization that has not yet started. According to standard SNMP operation, if the system is not in a proper state to accept a given set request for this value, it returns the standard SNMP error 'badValue'. Corresponds to the INITIALIZE command. |
| INT sysInitializeDelay | 1.3.6.1.4.1.33.1.18 | INTEGER | read-write | The number of minutes to delay before beginning the system initialization process as executed with sysInitialize. This value cannot be set outside a set-request that contains the value 'execute' for sysInitialize. If not included in such a set, the default value is 1. Corresponds to the INITIALIZE command's DELAY parameter and to the value labeled 'Minutes to shutdown:' in the SYSTEM STATUS display. |
| GAU sysInstalledMemory | 1.3.6.1.4.1.33.1.35 | Gauge | read-only | The total number of bytes of main memory installed in the system. Corresponds directly to the value labeled 'Installed' on the SERVER ALTERNATE STATUS display. A value of 0 indicates standard memory for the particular hardware. |
| OCT sysLoaderAddress | 1.3.6.1.4.1.33.1.24 | OCTET STRING | read-only | The network address of the system that provided this system's running software. Corresponds directly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| ADR sysLoaderAddressType | 1.3.6.1.4.1.33.1.23 | AddressType | read-only | The type of network address contained in sysLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's software was loaded from local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| STR sysLoaderName | 1.3.6.1.4.1.33.1.22 | DisplayString | read-only | The name of the system that provided this system's running software. Corresponds directly to the value labeled 'Primary Host:' in the SERVER STATUS display. |
| STR sysLoadSoftware | 1.3.6.1.4.1.33.1.5 | DisplayString | read-write | The software file name to request for down-line load of the server. Corresponds directly to SERVER SOFTWARE, and the value labeled 'Software:' in the SERVER CHARACTERISTICS display. |
| STR sysLocalName | 1.3.6.1.4.1.33.1.8 | DisplayString | read-write | The system's local name. Corresponds directly to SERVER NAME and the value labeled 'Name:' in the SERVER CHARACTERISTICS display. |
| OCT sysMaintenancePassword | 1.3.6.1.4.1.33.1.7 | OCTET STRING | read-write | The password a management system must supply to force the system to reboot or use the system's remote console via the Maintenance Operation Protocol (MOP). Corresponds directly to SERVER MAINTENANCE PASSWORD. When setting this value, the management system must supply eight octets, filling with zeros from the first octet. That is, the value '1ab42' would be expressed as '0.0.0.0.0.1.ab.42'. Setting the value to zero disables the password check. When returning this value, the agent always returns a zero length OCTET STRING. |
| CTR sysResourceLacks | 1.3.6.1.4.1.33.1.27 | Counter | read-only | The number of times a local resource allocation failed, for example due to lack of dynamic memory. Corresponds directly to the value labeled 'Resource Errors:' in the SERVER STATUS display. |
| INT sysResourceNumber | 1.3.6.1.4.1.33.1.30 | INTEGER | read-only | The number of resource entries in the Resource table. |
| INT sysRomVersion | 1.3.6.1.4.1.33.1.11 | INTEGER | read-only | The firmware version of the bootstrap ROM installed in the system. Corresponds directly to the value labeled 'Rom' in the SERVER CHARACTERISTICS display. |
| OCT sysSoftwareVersion | 1.3.6.1.4.1.33.1.10 | OCTET STRING | read-only | The software version running in the system. In order, the octets contain major version, minor version, ECO, and pre-release number. Corresponds to the numbers in the software version in the SERVER CHARACTERISTICS display. For example, the version display for sysSoftwareVersionType 'production' and sysSoftwareVersion '2.2.0.0' is 'V2.2'. The version display for sysSoftwareVersionType 'beta' and sysSoftwareVersion '3.1.0.4' is 'V3.1B4'. |
| INT sysSoftwareVersionType | 1.3.6.1.4.1.33.1.9 | INTEGER | read-only | The software version variant running in the system. Corresponds to the letter in the software version in the SERVER CHARACTERISTICS display. alpha 'A': alpha test beta 'B': beta test production null: normal, production software special 'S': special, custom software |
| OCT sysTimeZone | 1.3.6.1.4.1.33.1.4 | OCTET STRING | read-write | The adjustment to apply to a universal (Greenwich) time received when down-line loaded, comprising two octets. The first octet is the number of hours west of universal, the second is the number of minutes. Corresponds directly to SERVER TIMEZONE and the value labeled 'Timezone:' in the SERVER CHARACTERISTICS display. |
| INT sysZeroAll | 1.3.6.1.4.1.33.1.19 | INTEGER | read-write | Control to zero all counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's counters to be zeroed. Corresponds to the ZERO ALL command. |
| INT sysZeroBase | 1.3.6.1.4.1.33.1.20 | INTEGER | read-write | Control to zero all base counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's base counters to be zeroed. Examples of counters that are zeroed are the SNMP counters or the counters from the SYSTEM COUNTERS display. Examples of counters that are not zeroed are Ethernet interface counters or port counters. Corresponds to the ZERO SYSTEM command. |
| TIK sysZeroBaseTime | 1.3.6.1.4.1.33.1.21 | TimeTicks | read-only | The number hundredths of a second since the most recent zeroing of the base counters, such as through execution of sysZeroAll or sysZeroBase. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the SERVER COUNTERS display. |
| xSystem | 1.3.6.1.4.1.33.1 | |||
| xyplex | 1.3.6.1.4.1.33 |
FAQ
What is XYPLEX-SYSTEM-MIB used for when monitoring legacy Xyplex terminal servers?
It reports system-level hardware status, the running software version, and resource utilization, letting admins confirm a Xyplex terminal server's components are functioning correctly and identify which firmware it's running.
How would I detect an overloaded Xyplex terminal server using this MIB?
By polling the resource utilization objects covering CPU and memory usage, an admin can spot a Xyplex unit whose resource consumption is unusually high, signaling it may be overloaded and at risk of degraded terminal service.
RFC description
Enterprise MIB for Xyplex system management and device status monitoring.
Start monitoring Xyplex terminal servers/network access equipment (hardware/software-version/resource-utilization status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.