XEDIA-IP-MIB

All MIBs › XEDIA-IP-MIB

Organization: Xedia Corp.

Last Updated: 1997-02-18

Description: Xedia extended IP MIB providing read-write IP address configuration, interface-level address tables, and additional IP management objects beyond the IETF IP-MIB for Xedia devices

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is XEDIA-IP-MIB?

This proprietary MIB from Xedia Corporation extends IP-layer management on Xedia access routers beyond what the standard IETF IP-MIB provides. It exposes a per-interface IP address table with read-write configuration objects including netmask, broadcast address, source address, and router address, alongside status such as row activation state. Administrators use it to verify the software-configured IP addressing and reassembly settings on each interface, and the RowStatus-controlled table lets them monitor whether address entries are properly active or being provisioned. The module description explicitly states it supplements the IETF IP-MIB, showing a direct dependency on that standard. It is used in managing Xedia router deployments where IP interface addressing needs finer-grained per-address control than the standard IP-MIB offers. Engineers can download the XEDIA-IP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in XEDIA-IP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Xedia multiservice access router

Monitoring Examples

An administrator would poll xipIfIpAddrTable/xipIfIpAddrEntry to check xipIfIpAddr, xipIfIpAddrNetMask, and xipIfIpAddrBcastAddr against the intended configuration for a given interface, and check xipIfIpAddrRowStatus to confirm an address entry is active rather than stuck in notReady/notInService. An unexpected notInService row status or a mismatched xipIfIpAddrRouterAddress would reveal a failed or incomplete IP address provisioning operation. xipIfIpAddrSubnetProxyArp shows whether proxy ARP is enabled for that subnet.

What Can Be Monitored

per-interface IP address table
subnet mask configuration
broadcast address
router address
proxy ARP setting
address row activation status

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

From XEDIA-REG

xediaMibs

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using xipRouteCurrentCount OID:

Select a Xedia multiservice access router (per-interface IP address/netmask config status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type xipRouteCurrentCount into the Find box to locate it in the OID tree, then select it and click OK. The number of existing routes in the Xedia Route Table. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
xediaIpMIB	1.3.6.1.4.1.838.3.4			This module defines additional objects for management of IP in Xedia devices, above and beyond what is defined in the IETF's IP-MIB.
xipObjects	1.3.6.1.4.1.838.3.4.1
xipIfIpAddrTable	1.3.6.1.4.1.838.3.4.1.1		not-accessible	A table that allows configuration of IP addresses (since the ipAddrTable from the IP-MIB is read-only and not indexed by ifIndex).
xipIfIpAddrEntry	1.3.6.1.4.1.838.3.4.1.1.1		not-accessible	Information about a single IP address. Every entry with a non-zero value of xipIfIpAddr in this table will have a corresponding entry in the ipAddrTable, so adding an entry to this table is how you add an entry to that, read-only, table. Note that, unlike the ipAddrTable, this table's primary index is the ifIndex. This makes it easier to list the addresses associated with a particular interface. Some implementations may limit this to one address per interface.
IP xipIfIpAddr	1.3.6.1.4.1.838.3.4.1.1.1.1	IpAddress	read-create	The IP address to which this entry's addressing information pertains. The all-zeros value is an uninitialized value and indicates the address has not been set yet.
IP xipIfIpAddrNetMask	1.3.6.1.4.1.838.3.4.1.1.1.2	IpAddress	read-create	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. When the xipIfIpAddr object is set, the agent may set xipIfIpAddrNetMask automatically to the default mask based on the class of the address.
U32 xipIfIpAddrBcastAddr	1.3.6.1.4.1.838.3.4.1.1.1.3	Unsigned32	read-create	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
U32 xipIfIpAddrReasmMaxSize	1.3.6.1.4.1.838.3.4.1.1.1.4	Unsigned32	read-create	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
BIT xipIfIpAddrProtos	1.3.6.1.4.1.838.3.4.1.1.1.5	Bits	read-create	This object indicates whether RIPv2 and OSPFv2 are enabled for this address.
ROW xipIfIpAddrRowStatus	1.3.6.1.4.1.838.3.4.1.1.1.6	RowStatus	read-create	This object is used to add and remove entries from the table. Note that some agents will only allow one IP address per interface and therefore may automatically create an entry in this table for every IP interface in the system. In this case this object may be implemented in a minimal way (always return a 'wrongValue' error on any SET request and always return the value 'active(1)' when retrieved).
IP xipIfIpAddrSrcAddr	1.3.6.1.4.1.838.3.4.1.1.1.7	IpAddress	read-create	The IP address used as the src address in packets being transmitted on an unnumbered interface. The IP address should be the address assigned to an IP interface.
T/F xipIfIpAddrRouterAddress	1.3.6.1.4.1.838.3.4.1.1.1.8	TruthValue	read-create	The value of this object is 'true(1)' if the IP address represented by this entry is the router address, and 'false(2)' otherwise. This entry cannot be deleted if the value of this object is 'true(1)'.
INT xipIfIpAddrSubnetProxyArp	1.3.6.1.4.1.838.3.4.1.1.1.9	INTEGER	read-create	The administrative status for providing proxy arp for all hosts on this subnet. The value of 'enabled(1)' will cause the router to respond to all ARPs with its own mac address. This should only be enabled when all of the possible effects are understood.
INT xipIfIpAddrSource	1.3.6.1.4.1.838.3.4.1.1.1.10	INTEGER	read-only
xipStaticRouteTable	1.3.6.1.4.1.838.3.4.1.2		not-accessible	A table of static routes configured by the user. This table is used instead of the ipRouteTable (from MIB-II) because that table has no way of showing inactive static routes (routes that are not in use in the actual routing table but may be in the future, for example if an interface comes back up or if a route added by a protocol such as OSPF ages out.)
xipStaticRouteEntry	1.3.6.1.4.1.838.3.4.1.2.1		not-accessible	Information about a single static route.
IP xipStaticRouteDest	1.3.6.1.4.1.838.3.4.1.2.1.1	IpAddress	read-only	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Note the unusual value of MAX-ACCESS (for an index object).
IP xipStaticRouteMask	1.3.6.1.4.1.838.3.4.1.2.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
IP xipStaticRouteNextHop	1.3.6.1.4.1.838.3.4.1.2.1.3	IpAddress	read-only	The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
I32 xipStaticRouteCost	1.3.6.1.4.1.838.3.4.1.2.1.4	Integer32	read-create	The cost associated with this static route. It only has significance as compared to other static routes for the same destination network, mask, and tos.
I32 xipStaticRoutePref	1.3.6.1.4.1.838.3.4.1.2.1.5	Integer32	read-create	The preference associated with this route. This will be installed as ipRouteMetric2, an alternate routine metric for this route. Note that the presence of the DEFVAL means that the user does not need to supply the value on a create, however, the actual value will be determined by the agent and will not be -1.
INT xipStaticRouteStatus	1.3.6.1.4.1.838.3.4.1.2.1.6	INTEGER	read-only	An indication of whether this static route is installed in the IP forwarding database (which means it will be returned in the ipRouteTable). A static entry may be configured in this table but not be in the actual routing table because its associated interface may be down.
ROW xipStaticRouteRowStatus	1.3.6.1.4.1.838.3.4.1.2.1.7	RowStatus	read-create	The object that allows static routes to be created and deleted. This object only supports the values 'createAndGo(4)' and 'destroy(6)' which create and delete rows respectively. When setting the value to 'createAndGo(4)', the xipStaticNextHop object must have an explicit value set (and the xipStaticRouteDest object is set implicitly via the instance id). The other objects can take their default values.
I32 xipStaticRouteTos	1.3.6.1.4.1.838.3.4.1.2.1.8	Integer32	read-only	The Type of Service associated with the route.
INT xipStaticRouteSource	1.3.6.1.4.1.838.3.4.1.2.1.9	INTEGER	read-create	The source of this route, either configured by management or generated by some autoconfiguration process (internally or through external application).
T/F xipStaticRouteProxyArp	1.3.6.1.4.1.838.3.4.1.2.1.10	TruthValue	read-only	The value of this object is 'true' if proxy arp has been installed for this static route. Initially, this is only used for auto-generated static routes/proxy arp for VPN configurations.
T/F xipStaticRouteVolatile	1.3.6.1.4.1.838.3.4.1.2.1.11	TruthValue	read-create	The value of this object is 'true' if this static route entry is not stored in NVRAM.
xipIfArpTable	1.3.6.1.4.1.838.3.4.1.3		not-accessible	A table of per-interface ARP configuration.
xipIfArpEntry	1.3.6.1.4.1.838.3.4.1.3.1		not-accessible	ARP configuration for a specific (datalink) interface. This table 'sparce-augments' the ifTable from the IF-MIB: it contains an entry for every interface that supports ARP.
I32 xipIfArpCacheTimeout	1.3.6.1.4.1.838.3.4.1.3.1.1	Integer32	read-write	The timeout value, in minutes, that is used to age out entries from the ARP cache (the ipNetToMediaTable).
xipRouteObjects	1.3.6.1.4.1.838.3.4.1.4
INT xipRouteCurrentCountEx	1.3.6.1.4.1.838.3.4.1.4.1	INTEGER	read-only	The number of existing routes in the Xedia Route Table. For each Dest/mask route entry, it is the count of ALL next hops contained under ALL TOSes.
INT xipRouteCurrentNetworks	1.3.6.1.4.1.838.3.4.1.4.2	INTEGER	read-only	The number of existing routed Networks in the internal Route Table. It is the total number of Dest/Mask (network) route entries. Usually, it will also represent the number of route entries in the standard Route Table, except when there are Dest addresses with multiple masks.
INT xipRouteConfiguredMaxRoutes	1.3.6.1.4.1.838.3.4.1.4.3	INTEGER	read-write	The maximum number of routed Networks in the internal Route Table. It is the maximum total number of Dest/Mask (network) route entries. Depending upon system configuration and the number of route entries in the route table that are destination addresses with multple masks, it may not be possible to have a route table with the maximum number of routed networks. If this variable is changed, it will not take effect until the box is reset.
INT xipRouteOperationalMaxRoutes	1.3.6.1.4.1.838.3.4.1.4.4	INTEGER	read-only	The current value of the maximum number of routed networks in the internal route table, read from configuration memory upon startup.
INT xipRouteConfiguredMaxMemory	1.3.6.1.4.1.838.3.4.1.4.5	INTEGER	read-write	The maximum amount of memory that is available to be allocated to the routing protocols. If this variable is changed, it will not take effect until the box is reset. Depending upon system configuration, it may not be possible to set this variable to the maximum allowable value.
INT xipRouteOperationalMaxMemory	1.3.6.1.4.1.838.3.4.1.4.6	INTEGER	read-only	The current value of the maximum amount of memory that is available to be allocated to the routing protocols, read from configuration memory upon startup.
INT xipRouteMaxFwdEntries	1.3.6.1.4.1.838.3.4.1.4.7	INTEGER	read-write	The maximum number of forwarding cache entries allocated. If this value is changed, it will not take effect until the box is reset. Depending upon system configuration, it may not be possible to set this variable to the maximum allowable value.
INT xipRouteCurrentFwdEntries	1.3.6.1.4.1.838.3.4.1.4.8	INTEGER	read-only	The current number of active entries in the forwarding cache.
xipRouteTable	1.3.6.1.4.1.838.3.4.1.5		not-accessible	This entity's IP Routing table.
xipRouteEntry	1.3.6.1.4.1.838.3.4.1.5.1		not-accessible	A route to a particular destination.
IP xipRouteDest	1.3.6.1.4.1.838.3.4.1.5.1.1	IpAddress	read-only	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
IP xipRouteMask	1.3.6.1.4.1.838.3.4.1.5.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
I32 xipRouteTos	1.3.6.1.4.1.838.3.4.1.5.1.3	Integer32	read-only	The policy specifier is the IP TOS Field. The encoding of IP TOS is as specified by the following convention. Zero indicates the default path if no more specific policy applies. +-----+-----+-----+-----+-----+-----+-----+-----+ \| \| \| \| \| PRECEDENCE \| TYPE OF SERVICE \| 0 \| \| \| \| \| +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30
IP xipRouteNextHop	1.3.6.1.4.1.838.3.4.1.5.1.4	IpAddress	read-only	The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
NUM xipRouteIfIndex	1.3.6.1.4.1.838.3.4.1.5.1.5	InterfaceIndex	read-only	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT xipRouteType	1.3.6.1.4.1.838.3.4.1.5.1.6	INTEGER	read-only	The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture.
INT xipRouteProto	1.3.6.1.4.1.838.3.4.1.5.1.7	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
OID xipRouteInfo	1.3.6.1.4.1.838.3.4.1.5.1.8	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
INT xipRouteAge	1.3.6.1.4.1.838.3.4.1.5.1.9	INTEGER	read-only	The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
INT xipRouteMetric1	1.3.6.1.4.1.838.3.4.1.5.1.10	INTEGER	read-only	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT xipRouteMetric2	1.3.6.1.4.1.838.3.4.1.5.1.11	INTEGER	read-only	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT xipRouteDistance	1.3.6.1.4.1.838.3.4.1.5.1.12	INTEGER	read-only	Administrative distance of the route. When new route is added, route with smaller distance takes precedence over the route with higher value.
xipGeneral	1.3.6.1.4.1.838.3.4.1.6
INT xipFwdDirectedBroadcast	1.3.6.1.4.1.838.3.4.1.6.1	INTEGER	read-write	The administrative status for forwarding directed broadcasts. A value of 'enabled(1)' allows directed broadcasts to be forwarded on all interfaces while 'disabled(2)' disables the forwarding of directed broadcasts on all interfaces in the box.
INT xipIcmpRedirect	1.3.6.1.4.1.838.3.4.1.6.2	INTEGER	read-write	The administrative status for generating ICMP redirect messages. A value of 'enabled(1)' allows ICMP redirect messages to be generated on all interfaces while 'disabled(2)' disables the generation of ICMP redirect messages by the box.
IP xipDefaultNetwork	1.3.6.1.4.1.838.3.4.1.6.3	IpAddress	read-write	An IP network address to be used for default forwarding. The specific actions taken with this address depend on the operations or protocols configured to use it.
IP xipRouterAddress	1.3.6.1.4.1.838.3.4.1.6.4	IpAddress	read-only	The IP address currently being used as the router address.
INT xipIcmpRateLimiting	1.3.6.1.4.1.838.3.4.1.6.5	INTEGER	read-write	The administrative status for ICMP rate limiting. A value of 'enabled(1)' allows the rate of ICMP error messages to be limited on all interfaces while 'disabled(2)' disables ICMP rate limiting on all interfaces in the box.
INT xipIcmpRateLimit	1.3.6.1.4.1.838.3.4.1.6.6	INTEGER	read-write	The value which limits how often ICMP error messages are sent to a destination. The value is expressed in seconds.
xipForwardingTable	1.3.6.1.4.1.838.3.4.1.7		not-accessible	This entity's IP forwarding table.
xipForwardingEntry	1.3.6.1.4.1.838.3.4.1.7.1		not-accessible	Information about a single IP forwarding table entry. This MIB is no longer supported because the forwarding table now is index by destination and source IP addresses
IP xipForwardingDest	1.3.6.1.4.1.838.3.4.1.7.1.1	IpAddress	read-only	The destination IP address of this forwarding table entry.
IP xipForwardingNextHop	1.3.6.1.4.1.838.3.4.1.7.1.2	IpAddress	read-only	The next hop IP address used to forward traffic to the destination IP address of this forwarding table entry.
INT xipForwardingType	1.3.6.1.4.1.838.3.4.1.7.1.3	INTEGER	read-only	The type of traffic forwarded using this forwarding table entry.
NUM xipForwardingIfIndex	1.3.6.1.4.1.838.3.4.1.7.1.4	InterfaceIndex	read-only	The index value which uniquely identifies the local interface through which the destination of thie forwarding entry should be reached.The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
xipDSForwardingTable	1.3.6.1.4.1.838.3.4.1.8		not-accessible	This entity's IP forwarding table. It is based on destination + source IP addresses. It holds the forwarding entries for unicast, multicast, directed broadcast, and locally destined packets.
xipDSForwardingEntry	1.3.6.1.4.1.838.3.4.1.8.1		not-accessible	Information about a single IP forwarding table entry.
IP xipDSForwardingDest	1.3.6.1.4.1.838.3.4.1.8.1.1	IpAddress	read-only	The destination IP address of this forwarding table entry.
IP xipDSForwardingSource	1.3.6.1.4.1.838.3.4.1.8.1.2	IpAddress	read-only	The source IP address of this forwarding table entry.
IP xipDSForwardingNextHop	1.3.6.1.4.1.838.3.4.1.8.1.3	IpAddress	read-only	The next hop IP address used to forward traffic to the destination IP address of this forwarding table entry.
INT xipDSForwardingType	1.3.6.1.4.1.838.3.4.1.8.1.4	INTEGER	read-only	The type of traffic forwarded using this forwarding table entry.
NUM xipDSForwardingIfIndex	1.3.6.1.4.1.838.3.4.1.8.1.5	InterfaceIndex	read-only	The index value which uniquely identifies the local interface through which the destination of thie forwarding entry should be reached.The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
xipDSIForwardingTable	1.3.6.1.4.1.838.3.4.1.9		not-accessible	This entity's IP forwarding table. It is based on destination + source IP addresses. It holds the forwarding entries for unicast, multicast, directed broadcast, and locally destined packets.
xipDSIForwardingEntry	1.3.6.1.4.1.838.3.4.1.9.1		not-accessible	Information about a single IP forwarding table entry.
IP xipDSIForwardingDest	1.3.6.1.4.1.838.3.4.1.9.1.1	IpAddress	read-only	The destination IP address of this forwarding table entry.
IP xipDSIForwardingSource	1.3.6.1.4.1.838.3.4.1.9.1.2	IpAddress	read-only	The source IP address of this forwarding table entry.
NUM xipDSIForwardingIfIndex	1.3.6.1.4.1.838.3.4.1.9.1.3	InterfaceIndexOrZero	read-only	The index value which uniquely identifies the local interface through which the destination of thie forwarding entry should be reached.The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP xipDSIForwardingNextHop	1.3.6.1.4.1.838.3.4.1.9.1.4	IpAddress	read-only	The next hop IP address used to forward traffic to the destination IP address of this forwarding table entry.
INT xipDSIForwardingType	1.3.6.1.4.1.838.3.4.1.9.1.5	INTEGER	read-only	The type of traffic forwarded using this forwarding table entry.
xipIfTable	1.3.6.1.4.1.838.3.4.1.10		not-accessible	A table of information stored per IP physical or logical interface. The entries of this table are automatically created when a new IP interface is created corresponding to a new sublayer.
xipIfEntry	1.3.6.1.4.1.838.3.4.1.10.1		not-accessible	Information about a single IP interface.
IP xipIfPrimaryAddr	1.3.6.1.4.1.838.3.4.1.10.1.1	IpAddress	read-write	The IP address used as the receiving address when there is some ambiguity as to which IP address would receive it (e.g. multinetted interfaces). If a single address is configured on an interface, that address is used. If more than one address is configured, the first one configured is used but it can be modified through this parameter.
INT xipIfNegotiateAddr	1.3.6.1.4.1.838.3.4.1.10.1.2	INTEGER	read-write	If the value of this variable is 'enabled(1)', it will be assumed that the interface will receive an IP address from a peer (typically a PPP peer). Addition of an IP address to the interface any other way will not be allowed. If the IP interface is stacked above a datalink which supports dial-on-demand, an unnumbered IP address will be added to the interface while the link is down.
xipNotifications	1.3.6.1.4.1.838.3.4.2
xipConformance	1.3.6.1.4.1.838.3.4.3
xipCompliances	1.3.6.1.4.1.838.3.4.3.1
xipCompliance	1.3.6.1.4.1.838.3.4.3.1.1			The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
xipGroups	1.3.6.1.4.1.838.3.4.3.2
xipAllGroup	1.3.6.1.4.1.838.3.4.3.2.1			The set of all accessible objects in this MIB.

RFC description

Provides IP address configuration and management extensions for Xedia devices beyond standard IP MIB definitions.

Start monitoring Xedia multiservice access router (per-interface IP address/netmask config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download XEDIA-IP-MIB