Wellfleet-ST2-MIB

All MIBs › Wellfleet-ST2-MIB

Category: Wellfleet BayNetworks System Management

Description: Manages Wellfleet ST-II (Stream Protocol Version 2) resource reservation parameters and flow statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-ST2-MIB?

The Wellfleet-ST2-MIB is a Wellfleet Communications proprietary MIB for managing Stream Protocol, Version 2 (ST-II), an early Internet resource-reservation protocol for real-time flows, as implemented on Wellfleet routers. It exposes objects for configuring and tracking reserved streams and their flow-specific parameters, along with statistics on stream setup, teardown, and forwarded traffic. Its monitoring value lies mainly in software/service state: it lets an operator confirm how many reservation streams are active, whether stream setup requests are succeeding, and whether a stream's flow statistics match the reserved bandwidth, revealing resource-reservation failures for real-time applications. It corresponds to the protocol later documented in RFC 1819 (ST2+) though implemented here as a vendor-specific object set. It was used on Wellfleet/Bay Networks routers in early experimental or carrier trials of guaranteed-bandwidth multimedia/real-time streaming over IP-based WANs. Engineers can download the Wellfleet-ST2-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-ST2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet router
Bay Networks/Nortel router with ST-II support

Monitoring Examples

A network engineer polls the stream reservation table to count currently active ST-II flows and checks each stream's negotiated flow-spec against its actual forwarded traffic statistics. A stream whose reserved parameters were successfully negotiated but whose forwarded packet counters stay at zero suggests the reservation succeeded at the control-plane level while the data path itself is failing to carry traffic.

What Can Be Monitored

active stream reservations
flow-spec parameters
stream setup/teardown events
forwarded stream traffic statistics

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfReservationProtocolGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfSt2Group	1.3.6.1.4.1.18.3.5.16.1.2
wfSt2BaseGroup	1.3.6.1.4.1.18.3.5.16.1.2.1
INT wfSt2BaseDelete	1.3.6.1.4.1.18.3.5.16.1.2.1.1	INTEGER	read-write	This value determines whether ST2 is configured on this slot.
INT wfSt2BaseDisable	1.3.6.1.4.1.18.3.5.16.1.2.1.2	INTEGER	read-write	This value determines whether ST2 is to startup.
INT wfSt2BaseState	1.3.6.1.4.1.18.3.5.16.1.2.1.3	INTEGER	read-only	This value records the current state of ST2.
STR wfSt2BaseRoutingVers	1.3.6.1.4.1.18.3.5.16.1.2.1.4	DisplayString	read-only	'This read-only parameter identifies the executor node's Routing version number. The format is the same as for the Network Management version number.'
INT wfSt2BaseTunnelCapability	1.3.6.1.4.1.18.3.5.16.1.2.1.5	INTEGER	read-write	This is the tunnelling capability flag for the router.
INT wfSt2BaseTunnelDisable	1.3.6.1.4.1.18.3.5.16.1.2.1.6	INTEGER	read-write	This is the tunnelling enabled flag for the router.
INT wfSt2BaseAgentDBGMask	1.3.6.1.4.1.18.3.5.16.1.2.1.7	INTEGER	read-write	This is the ST2 base agent debug mask.
INT wfSt2BaseReservedParameter1	1.3.6.1.4.1.18.3.5.16.1.2.1.8	INTEGER	read-write	This is the ST2 base reserved parameter.
INT wfSt2BaseReservedParameter2	1.3.6.1.4.1.18.3.5.16.1.2.1.9	INTEGER	read-write	This is the ST2 base reserved parameter.
wfSt2CircuitTable	1.3.6.1.4.1.18.3.5.16.1.2.2		not-accessible	' Table of ST2 Circuit Configuration and Counter Records'
wfSt2CircuitEntry	1.3.6.1.4.1.18.3.5.16.1.2.2.1		not-accessible	'Parameters information about all circuits currently known. NOTE: depending on the type of object being querried (e.g., a level 1 vs. a level 2 router or end system) some variables may not be present.'
INT wfSt2CircuitDelete	1.3.6.1.4.1.18.3.5.16.1.2.2.1.1	INTEGER	read-write	This value determines whether the circuit is configured
INT wfSt2CircuitDisable	1.3.6.1.4.1.18.3.5.16.1.2.2.1.2	INTEGER	read-write	'This value represents the circuit's Network Management operational state. NOTE: These values are incremented by one compared to the standard St2 values in order to maintain compliance with RFC 1155.'
INT wfSt2CircuitCommonState	1.3.6.1.4.1.18.3.5.16.1.2.2.1.3	INTEGER	read-only	This value represents the circuit's operational state.
INT wfSt2CircuitID	1.3.6.1.4.1.18.3.5.16.1.2.2.1.4	INTEGER	read-only	A unique value for each known circuit.
INT wfSt2CircuitCommonType	1.3.6.1.4.1.18.3.5.16.1.2.2.1.5	INTEGER	read-only	'Represents the type of the circuit.'
IP wfSt2CircuitIPAddress	1.3.6.1.4.1.18.3.5.16.1.2.2.1.6	IpAddress	read-write	Network Interface IP address of this ST2 circuit
INT wfSt2CircuitTmoAccept	1.3.6.1.4.1.18.3.5.16.1.2.2.1.7	INTEGER	read-write	Transmit accept ...
INT wfSt2CircuitRetryAccept	1.3.6.1.4.1.18.3.5.16.1.2.2.1.8	INTEGER	read-write	Receive accept ...
INT wfSt2CircuitTmoConnect	1.3.6.1.4.1.18.3.5.16.1.2.2.1.9	INTEGER	read-write	Transmit connect ...
INT wfSt2CircuitRetryConnect	1.3.6.1.4.1.18.3.5.16.1.2.2.1.10	INTEGER	read-write	Receive connect ...
INT wfSt2CircuitTmoDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.2.1.11	INTEGER	read-write	Transmit disconnect ...
INT wfSt2CircuitRetryDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.2.1.12	INTEGER	read-write	Receive disconnect ...
INT wfSt2CircuitTmoHidChange	1.3.6.1.4.1.18.3.5.16.1.2.2.1.13	INTEGER	read-write	Transmit hid change ...
INT wfSt2CircuitRetryHidChange	1.3.6.1.4.1.18.3.5.16.1.2.2.1.14	INTEGER	read-write	Receive Hid Change ...
INT wfSt2CircuitTmoRefuse	1.3.6.1.4.1.18.3.5.16.1.2.2.1.15	INTEGER	read-write	Transmit refuse ...
INT wfSt2CircuitRetryRefuse	1.3.6.1.4.1.18.3.5.16.1.2.2.1.16	INTEGER	read-write	Receive refuse ...
INT wfSt2CircuitTmoHello	1.3.6.1.4.1.18.3.5.16.1.2.2.1.17	INTEGER	read-write	Transmit hello ...
INT wfSt2CircuitRetryHello	1.3.6.1.4.1.18.3.5.16.1.2.2.1.18	INTEGER	read-write	Receive hello ...
INT wfSt2CircuitMTU	1.3.6.1.4.1.18.3.5.16.1.2.2.1.19	INTEGER	read-write	Maximum transmission unit ...
INT wfSt2CircuitDBGMask	1.3.6.1.4.1.18.3.5.16.1.2.2.1.20	INTEGER	read-write	Debug mask ...
INT wfSt2CircuitHelloFailure	1.3.6.1.4.1.18.3.5.16.1.2.2.1.21	INTEGER	read-write	The stream is to be preserved even though helloing fails.
INT wfSt2CircuitHidProposed	1.3.6.1.4.1.18.3.5.16.1.2.2.1.22	INTEGER	read-write	Hid proposed flag ...
CTR wfSt2CircuitBadStCksum	1.3.6.1.4.1.18.3.5.16.1.2.2.1.23	Counter	read-only	Bad St2 checksum ...
CTR wfSt2CircuitEncodeBadParm	1.3.6.1.4.1.18.3.5.16.1.2.2.1.24	Counter	read-only	Bad parameter encoding ...
CTR wfSt2CircuitEncodeWrongParms	1.3.6.1.4.1.18.3.5.16.1.2.2.1.25	Counter	read-only	Wrong parameter encoded ...
CTR wfSt2CircuitMsgInHidColl	1.3.6.1.4.1.18.3.5.16.1.2.2.1.26	Counter	read-only	Message in Hid ...
CTR wfSt2CircuitMsgInNoCon	1.3.6.1.4.1.18.3.5.16.1.2.2.1.27	Counter	read-only	Message in No ...
CTR wfSt2CircuitNotSt2	1.3.6.1.4.1.18.3.5.16.1.2.2.1.28	Counter	read-only	Not an St2 packet ...
CTR wfSt2CircuitParmMissing	1.3.6.1.4.1.18.3.5.16.1.2.2.1.29	Counter	read-only	Circuit parameter missing ...
CTR wfSt2CircuitScmpRefNum	1.3.6.1.4.1.18.3.5.16.1.2.2.1.30	Counter	read-only	Number of Scmp refuses ...
CTR wfSt2CircuitScmp0rVlid	1.3.6.1.4.1.18.3.5.16.1.2.2.1.31	Counter	read-only	Scmp Or Vlid ...
CTR wfSt2CircuitScmp0sVlid	1.3.6.1.4.1.18.3.5.16.1.2.2.1.32	Counter	read-only	Scmp Os Vlid ...
CTR wfSt2CircuitScmpBadVlid	1.3.6.1.4.1.18.3.5.16.1.2.2.1.33	Counter	read-only	Bad Scmp Vlid ...
CTR wfSt2CircuitScmpCksum	1.3.6.1.4.1.18.3.5.16.1.2.2.1.34	Counter	read-only	Scmp checksun ...
CTR wfSt2CircuitScmpFailedResources	1.3.6.1.4.1.18.3.5.16.1.2.2.1.35	Counter	read-only	Scmp recources failed ...
CTR wfSt2CircuitScmpFailedRoute	1.3.6.1.4.1.18.3.5.16.1.2.2.1.36	Counter	read-only	Scmp routed failed ...
CTR wfSt2CircuitScmpLenInconsist	1.3.6.1.4.1.18.3.5.16.1.2.2.1.37	Counter	read-only	Scmp packet length inconsistent ...
CTR wfSt2CircuitScmpRxTimeOut	1.3.6.1.4.1.18.3.5.16.1.2.2.1.38	Counter	read-only	Scmp receive time outs ...
CTR wfSt2CircuitScmpXmtCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.39	Counter	read-only	Scmp transmit count ...
CTR wfSt2CircuitScmpRcvCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.40	Counter	read-only	Scmp receive count ...
CTR wfSt2CircuitDataXmtCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.41	Counter	read-only	Transmited data count ...
CTR wfSt2CircuitDataRcvCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.42	Counter	read-only	received data count ...
CTR wfSt2CircuitSt2StreamCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.43	Counter	read-only	St2 stream count ...
CTR wfSt2CircuitHelloXmtCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.44	Counter	read-only	Hellos transmitted count ...
CTR wfSt2CircuitHelloRcvCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.45	Counter	read-only	Hellos received count ...
CTR wfSt2CircuitHelloRAckCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.46	Counter	read-only	Hellos received acknowledged coubt ...
CTR wfSt2CircuitLbPoliceDrop	1.3.6.1.4.1.18.3.5.16.1.2.2.1.47	Counter	read-only	Learning bridge police drop count ...
CTR wfSt2CircuitPbsDropCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.48	Counter	read-only	Pbs drop count ...
CTR wfSt2CircuitOverDrop2Cnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.49	Counter	read-only	Over drop ? count ...
CTR wfSt2CircuitPktCnt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.50	Counter	read-only	Circuit packet count ...
CTR wfSt2CircuitScmpXmt	1.3.6.1.4.1.18.3.5.16.1.2.2.1.51	Counter	read-only	Scmp packets transmitted ...
CTR wfSt2CircuitScmpRcv	1.3.6.1.4.1.18.3.5.16.1.2.2.1.52	Counter	read-only	Scmp packets received ...
CTR wfSt2CircuitBWAlloc	1.3.6.1.4.1.18.3.5.16.1.2.2.1.53	Counter	read-only	Circuit bandwith allocated ...
INT wfSt2CircuitRsvdParameter1	1.3.6.1.4.1.18.3.5.16.1.2.2.1.54	INTEGER	read-write	Circuit reserved parameter
INT wfSt2CircuitRsvdParameter2	1.3.6.1.4.1.18.3.5.16.1.2.2.1.55	INTEGER	read-write	Circuit reserved parameter
wfSt2NeighborTable	1.3.6.1.4.1.18.3.5.16.1.2.3		not-accessible	The ST2 neighbor routing table
wfSt2NeighborEntry	1.3.6.1.4.1.18.3.5.16.1.2.3.1		not-accessible	Neighbor Table
INT wfSt2NeighborDelete	1.3.6.1.4.1.18.3.5.16.1.2.3.1.1	INTEGER	read-write	Determines whether the base record is configured
INT wfSt2NeighborDisable	1.3.6.1.4.1.18.3.5.16.1.2.3.1.2	INTEGER	read-write	Determines whether the base record is active
IP wfSt2NeighborNxtHopIPAddr	1.3.6.1.4.1.18.3.5.16.1.2.3.1.3	IpAddress	read-only	IP address of next hop router
INT wfSt2NeighborRteExplr	1.3.6.1.4.1.18.3.5.16.1.2.3.1.4	INTEGER	read-write	Is the neighbor capable of route exploration
INT wfSt2NeighborHelloProtocol	1.3.6.1.4.1.18.3.5.16.1.2.3.1.5	INTEGER	read-write	Helloing in use
INT wfSt2NeighborType	1.3.6.1.4.1.18.3.5.16.1.2.3.1.6	INTEGER	read-write	Neighbor type, local or tunnel
INT wfSt2NeighborPriorityLevel	1.3.6.1.4.1.18.3.5.16.1.2.3.1.7	INTEGER	read-write	Route exploration or tunnel priority level
INT wfSt2NeighborRsvdParameter1	1.3.6.1.4.1.18.3.5.16.1.2.3.1.8	INTEGER	read-write	neighbor reserved parameter
INT wfSt2NeighborRsvdParameter2	1.3.6.1.4.1.18.3.5.16.1.2.3.1.9	INTEGER	read-write	neighbor reserved parameter
IP wfSt2NeighborLocalIPAddress	1.3.6.1.4.1.18.3.5.16.1.2.3.1.10	IpAddress	read-write	Network Interface IP address of the local tunnel endpoint
INT wfSt2NeighborTmoAccept	1.3.6.1.4.1.18.3.5.16.1.2.3.1.11	INTEGER	read-write	Transmit accept ...
INT wfSt2NeighborRetryAccept	1.3.6.1.4.1.18.3.5.16.1.2.3.1.12	INTEGER	read-write	Receive accept ...
INT wfSt2NeighborTmoConnect	1.3.6.1.4.1.18.3.5.16.1.2.3.1.13	INTEGER	read-write	Transmit connect ...
INT wfSt2NeighborRetryConnect	1.3.6.1.4.1.18.3.5.16.1.2.3.1.14	INTEGER	read-write	Receive connect ...
INT wfSt2NeighborTmoDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.3.1.15	INTEGER	read-write	Transmit disconnect ...
INT wfSt2NeighborRetryDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.3.1.16	INTEGER	read-write	Receive disconnect ...
INT wfSt2NeighborTmoHidChange	1.3.6.1.4.1.18.3.5.16.1.2.3.1.17	INTEGER	read-write	Transmit hid change ...
INT wfSt2NeighborRetryHidChange	1.3.6.1.4.1.18.3.5.16.1.2.3.1.18	INTEGER	read-write	Receive Hid Change ...
INT wfSt2NeighborTmoRefuse	1.3.6.1.4.1.18.3.5.16.1.2.3.1.19	INTEGER	read-write	Transmit refuse ...
INT wfSt2NeighborRetryRefuse	1.3.6.1.4.1.18.3.5.16.1.2.3.1.20	INTEGER	read-write	Receive refuse ...
INT wfSt2NeighborTmoHello	1.3.6.1.4.1.18.3.5.16.1.2.3.1.21	INTEGER	read-write	Transmit hello ...
INT wfSt2NeighborRetryHello	1.3.6.1.4.1.18.3.5.16.1.2.3.1.22	INTEGER	read-write	Receive hello ...

RFC description

Manages ST2 reservation protocol configuration for Wellfleet network routers.

Start monitoring Wellfleet/Bay Networks/Nortel routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-ST2-MIB

What Is Wellfleet-ST2-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description