Wellfleet-CONSOLE-MIB

All MIBs › Wellfleet-CONSOLE-MIB

Category: Wellfleet BayNetworks System Management

Description: Manages Wellfleet router console port configuration, access control, and terminal session parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-CONSOLE-MIB?

Wellfleet-CONSOLE-MIB is a legacy vendor MIB from Wellfleet Communications (a router vendor later merged into Bay Networks/Nortel) for managing a router's local console port. It exposes configuration objects for console access control and terminal session parameters, such as baud rate, timeout, and access permissions. Its monitoring value is oriented toward software/administrative status -- confirming console port configuration and session activity -- rather than physical hardware sensors like temperature or power. No sample objects were provided so exact table/object names cannot be confirmed, but it is a self-contained Wellfleet enterprise MIB without an evident dependency on external standard MIBs. It is typically deployed on legacy Wellfleet/Bay Networks routers where administrators manage local out-of-band console access. Engineers can download the Wellfleet-CONSOLE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-CONSOLE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks router

Monitoring Examples

Since sample_objects is empty for this MIB, no concrete Wellfleet-CONSOLE-MIB object names are available to ground a specific polling example, though based on the module description an operator would generally be expected to poll console port configuration objects (such as terminal parameters and access control settings) to confirm console access is properly restricted and configured.

What Can Be Monitored

console port configuration
console access control settings

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfSerialPortGroup	OBJECT-IDENTITY
wfServices	OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfConsole	1.3.6.1.4.1.18.3.3.2.1
INT wfBaudRate	1.3.6.1.4.1.18.3.3.2.1.1	INTEGER	read-write	Baud rate configured on the Technician Interface console
INT wfDataBits	1.3.6.1.4.1.18.3.3.2.1.2	INTEGER	read-write	Number of data bits configured on the Technician Interface console
INT wfParity	1.3.6.1.4.1.18.3.3.2.1.3	INTEGER	read-write	Type of parity configured on the Technician Interface console
INT wfStopBits	1.3.6.1.4.1.18.3.3.2.1.4	INTEGER	read-write	Number of stop bits configured on the Technician Interface console
INT wfModemEnable	1.3.6.1.4.1.18.3.3.2.1.5	INTEGER	read-write	Enable the Technician Interface console to run over a modem
INT wfLinesPerScreen	1.3.6.1.4.1.18.3.3.2.1.6	INTEGER	read-write	Number of lines which can be displayed in one screen on the Technician Interface console
INT wfMoreEnable	1.3.6.1.4.1.18.3.3.2.1.7	INTEGER	read-write	Enable the 'more' feature on the Technician Interface console
STR wfPrompt	1.3.6.1.4.1.18.3.3.2.1.8	DisplayString	read-write	Character string which will be used as the system prompt on the Technician Interface console
INT wfLoginTimeOut	1.3.6.1.4.1.18.3.3.2.1.9	INTEGER	read-write	IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt
INT wfPasswordTimeOut	1.3.6.1.4.1.18.3.3.2.1.10	INTEGER	read-write	Timout on Password entry
INT wfCommandTimeOut	1.3.6.1.4.1.18.3.3.2.1.11	INTEGER	read-write	IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt
INT wfLoginRetries	1.3.6.1.4.1.18.3.3.2.1.12	INTEGER	read-write	IF MODEM_ENABLED then limit # of login attempts then HUP
CTR wfTotalLogins	1.3.6.1.4.1.18.3.3.2.1.13	Counter	read-only	Total number of TI login attempts
CTR wfUserLoginErrors	1.3.6.1.4.1.18.3.3.2.1.14	Counter	read-only	Total number of FAILED User login attempts
CTR wfManagerLoginErrors	1.3.6.1.4.1.18.3.3.2.1.15	Counter	read-only	Total number of FAILED Manager login attempts
CTR wfOtherLoginErrors	1.3.6.1.4.1.18.3.3.2.1.16	Counter	read-only	Total number of FAILED Other login attempts
CTR wfTtyFrameErrors	1.3.6.1.4.1.18.3.3.2.1.17	Counter	read-only	Count of TTY Frame errors
CTR wfTtyOverrunErrors	1.3.6.1.4.1.18.3.3.2.1.18	Counter	read-only	Count of TTY Overrun errors
CTR wfTtyParityErrors	1.3.6.1.4.1.18.3.3.2.1.19	Counter	read-only	Count of TTY Parity errors
CTR wfTtyInfifoErrors	1.3.6.1.4.1.18.3.3.2.1.20	Counter	read-only	Count of TTY Input Fifo errors
wfSerialPortTable	1.3.6.1.4.1.18.3.3.2.11.1		not-accessible	Configuration of system serial port(s)
wfSerialPortEntry	1.3.6.1.4.1.18.3.3.2.11.1.1		not-accessible	Information for each serial port.
INT wfSerialPortDelete	1.3.6.1.4.1.18.3.3.2.11.1.1.1	INTEGER	read-write	Flag to indicate Serial Port instance deletion
INT wfSerialPortDisable	1.3.6.1.4.1.18.3.3.2.11.1.1.2	INTEGER	read-write	Enable or disable this Serial Port
INT wfSerialPortState	1.3.6.1.4.1.18.3.3.2.11.1.1.3	INTEGER	read-only	The state of this Serial Port
INT wfSerialPortNumber	1.3.6.1.4.1.18.3.3.2.11.1.1.4	INTEGER	read-only	Serial Port number
STR wfSerialPortName	1.3.6.1.4.1.18.3.3.2.11.1.1.5	DisplayString	read-only	Serial Port name
INT wfSerialPortSlot	1.3.6.1.4.1.18.3.3.2.11.1.1.6	INTEGER	read-only	Slot number of Serial Port session
INT wfSerialPortType	1.3.6.1.4.1.18.3.3.2.11.1.1.7	INTEGER	read-write	Type of Serial Port
INT wfSerialPortBaudRate	1.3.6.1.4.1.18.3.3.2.11.1.1.8	INTEGER	read-write	Baud rate configured on this Serial Port
INT wfSerialPortDataBits	1.3.6.1.4.1.18.3.3.2.11.1.1.9	INTEGER	read-write	Number of data bits configured on this Serial Port
INT wfSerialPortParity	1.3.6.1.4.1.18.3.3.2.11.1.1.10	INTEGER	read-write	Type of parity configured on this Serial Port
INT wfSerialPortStopBits	1.3.6.1.4.1.18.3.3.2.11.1.1.11	INTEGER	read-write	Number of stop bits configured on this Serial Port
INT wfSerialPortModemEnable	1.3.6.1.4.1.18.3.3.2.11.1.1.12	INTEGER	read-write	Enable the Serial Port to run with modem leads enabled
INT wfSerialPortLinesPerScreen	1.3.6.1.4.1.18.3.3.2.11.1.1.13	INTEGER	read-write	Number of lines which can be displayed in one screen on the Serial Port
INT wfSerialPortMoreEnable	1.3.6.1.4.1.18.3.3.2.11.1.1.14	INTEGER	read-write	Enable the 'more' feature on the Serial Port
STR wfSerialPortPrompt	1.3.6.1.4.1.18.3.3.2.11.1.1.15	DisplayString	read-write	Character string which will be used as the system prompt on the Serial Port
INT wfSerialPortLoginTimeOut	1.3.6.1.4.1.18.3.3.2.11.1.1.16	INTEGER	read-write	IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt
INT wfSerialPortPasswordTimeOut	1.3.6.1.4.1.18.3.3.2.11.1.1.17	INTEGER	read-write	Timout on Password entry
INT wfSerialPortCommandTimeOut	1.3.6.1.4.1.18.3.3.2.11.1.1.18	INTEGER	read-write	IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt
INT wfSerialPortLoginRetries	1.3.6.1.4.1.18.3.3.2.11.1.1.19	INTEGER	read-write	IF MODEM_ENABLED then limit # of login attempts then HUP
CTR wfSerialPortTotalLogins	1.3.6.1.4.1.18.3.3.2.11.1.1.20	Counter	read-only	Total number of TI login attempts on Serial Port
CTR wfSerialPortUserLoginErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.21	Counter	read-only	Total number of FAILED User login attempts on Serial Port
CTR wfSerialPortManagerLoginErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.22	Counter	read-only	Total number of FAILED Manager login attempts on Serial Port
CTR wfSerialPortOtherLoginErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.23	Counter	read-only	Total number of FAILED Other login attempts on Serial Port
CTR wfSerialPortTtyFrameErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.24	Counter	read-only	Count of TTY Frame errors on Serial Port
CTR wfSerialPortTtyOverrunErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.25	Counter	read-only	Count of TTY Overrun errors on Serial Port
CTR wfSerialPortTtyParityErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.26	Counter	read-only	Count of TTY Parity errors on Serial Port
CTR wfSerialPortTtyInfifoErrors	1.3.6.1.4.1.18.3.3.2.11.1.1.27	Counter	read-only	Count of TTY Input Fifo errors on Serial Port
STR wfSerialPortInitialSearchPath	1.3.6.1.4.1.18.3.3.2.11.1.1.28	DisplayString	read-write	Example: 'A:;1:;2:' or '2:;4:6:;9:
STR wfSerialPortManagerAutoScript	1.3.6.1.4.1.18.3.3.2.11.1.1.29	DisplayString	read-write	for each login.
STR wfSerialPortUserAutoScript	1.3.6.1.4.1.18.3.3.2.11.1.1.30	DisplayString	read-write	for each login.
INT wfSerialPortUserAbortLogoutDisable	1.3.6.1.4.1.18.3.3.2.11.1.1.31	INTEGER	read-write	a USER from escaping out of the User Autoscript
INT wfSerialPortHistoryDepth	1.3.6.1.4.1.18.3.3.2.11.1.1.32	INTEGER	read-write	TI command history table size
INT wfSerialPortAutoSaveNumFiles	1.3.6.1.4.1.18.3.3.2.11.1.1.33	INTEGER	read-write	Number of times AutoSave will save the log 0 - disable the AutoSave log
STR wfSerialPortAutoSaveVolume	1.3.6.1.4.1.18.3.3.2.11.1.1.34	DisplayString	read-write	Volume, to which AutoSave will save logs Example: 'A:' or '2:'
STR wfSerialPortModemIdSwRev	1.3.6.1.4.1.18.3.3.2.11.1.1.35	DisplayString	read-only	A textual description of the modem's firmware version number.
STR wfSerialPortModemIdHwRev	1.3.6.1.4.1.18.3.3.2.11.1.1.36	DisplayString	read-only	A textual description of the revision number of the modem daughter card.
INT wfSerialPortModemLineState	1.3.6.1.4.1.18.3.3.2.11.1.1.37	INTEGER	read-only	Indicates the state of the modem.
INT wfSerialPortModemCfgFactoryDefaults	1.3.6.1.4.1.18.3.3.2.11.1.1.38	INTEGER	read-write	This object indicates if factory defaults are to be loaded. If set to enabled(1), factory defaults are loaded. If set to disabled(2), the initialization string in wfModemCfgInitString is not sent to the modem.
STR wfSerialPortModemCfgInitString	1.3.6.1.4.1.18.3.3.2.11.1.1.39	DisplayString	read-write	An initialization string that will be sent to the modem each time the modem is rebooted.
STR wfSerialPortModemCfgDefaultString	1.3.6.1.4.1.18.3.3.2.11.1.1.40	DisplayString	read-only	The string contains AT comands for initializing the modem every time the modem comes up, regardless of configuration.
STR wfSerialPortModemCfgResultCodeString	1.3.6.1.4.1.18.3.3.2.11.1.1.41	DisplayString	read-only	The ASCII response string returned by the modem. Response strings will be returned in response to last command to the modem and in response to activity on the line.
INT wfSerialPortModemCfgState	1.3.6.1.4.1.18.3.3.2.11.1.1.42	INTEGER	read-write	Indicates the state of AT command processing. When a new initialization string is to be sent to the modem, the sender sets the state to cfgInProgress(2). After the command has been sent to the modem, and a result code has been returned, the state is set to cfgResponseReturned(3). Once the sender has received the return code, the sender sets the state to cfgIdle(1).
INT wfSerialPortModemCfgCountry	1.3.6.1.4.1.18.3.3.2.11.1.1.43	INTEGER	read-write	Identifies the country the modem is designed to operate in. This object is not read from the modem directly. It must be entered manually when configuring the modem.
INT wfSerialPortModemInitState	1.3.6.1.4.1.18.3.3.2.11.1.1.44	INTEGER	read-only	Indictes the state of the modem initialization sequence. The state will freeze in the state that fails when a failure is detected. Otherwise, the state will be set to initComplete when initialization completes successfully. The state number correspond to those for the COM port modems. Some of the states are not valid for the console modem.

RFC description

Configures console serial port settings including baud rate and modem support on Wellfleet devices.

Start monitoring Wellfleet/Bay Networks router (console baud-rate/access config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-CONSOLE-MIB

What Is Wellfleet-CONSOLE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description