Wellfleet-IREDUND-MIB

All MIBs › Wellfleet-IREDUND-MIB

Category: Wellfleet BayNetworks System Management

Description: Monitors Wellfleet interface redundancy parameters, backup link states, and failover event statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-IREDUND-MIB?

Wellfleet-IREDUND-MIB is a Wellfleet Communications (later merged into Bay Networks/Nortel) enterprise MIB for monitoring interface redundancy, tracking backup/standby link states and failover event statistics on Wellfleet routers. No module description or sample objects were extracted here, so exact object/table names cannot be confirmed, but based on its name and short description it would expose per-interface redundancy role/state (active vs. backup), failover event counters, and related configuration. Its core monitoring value is availability/fault-related: detecting when a primary link has failed over to a backup and how often that has occurred, which speaks directly to hardware/link health rather than general performance. It likely depends on Wellfleet's own interface/chassis MIB conventions for identifying the physical interfaces involved in redundancy pairs. It would be deployed on legacy Wellfleet/Bay Networks routers in WAN environments using dual/backup links for high availability. Engineers can download the Wellfleet-IREDUND-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-IREDUND-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet Communications (Bay Networks) routers

Monitoring Examples

No object or table names were available in the extracted metadata for this module, so a concrete monitoring scenario cannot be honestly constructed beyond the general expectation of backup-link state and failover-event counters implied by the module's short description.

Imported Objects

From RFC-1212

OBJECT-TYPE

From Wellfleet-COMMON-MIB

wfIRedundGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfIRedundIfTable	1.3.6.1.4.1.18.3.5.1.10.1		not-accessible	WF_IREDUND_INTERFACE_TABLE - Interface REDUNDANCY This tabulates the interfaces within an interface redundancy group. All interfaces are indexed according to their physical slot and connector designation. All interfaces in the same circuit act as redundant (hot stand-by) interfaces for that circuit. At any given time, one hot stand-by interface is chosen to be the active interface for a circuit. The active interface is the only interface that is reading and writing data to/from the media.
wfIRedundIfEntry	1.3.6.1.4.1.18.3.5.1.10.1.1		not-accessible	Redundant interface entries.
INT wfIRedundIfDelete	1.3.6.1.4.1.18.3.5.1.10.1.1.1	INTEGER	read-write	Creation and deletion flag for this record. When set, it will cause this entry to be deleted from the MIB.
INT wfIRedundIfDisable	1.3.6.1.4.1.18.3.5.1.10.1.1.2	INTEGER	read-write	Enable/Disable parameter. A disabled interface will never be selected as the active interface for a circuit.
INT wfIRedundIfCct	1.3.6.1.4.1.18.3.5.1.10.1.1.3	INTEGER	read-write	The circuit number of the circuit to which the interface belongs. This interface will either act as the active interface for the the circuit or as a hot stand-by.
INT wfIRedundIfSlot	1.3.6.1.4.1.18.3.5.1.10.1.1.4	INTEGER	read-only	Slot ID of the interface, used as instance ID
INT wfIRedundIfPort	1.3.6.1.4.1.18.3.5.1.10.1.1.5	INTEGER	read-only	Port ID of the interface, used as instance ID
INT wfIRedundIfPrimary	1.3.6.1.4.1.18.3.5.1.10.1.1.6	INTEGER	read-write	Primary flag, indicates if this has been chosen as the primary interface. Only one interface in any circuit can be selected as a PRIMARY interface. The PRIMARY interface will have priority when an active interface is selected for a circuit. In general, if a PRIMARY circuit is available at active interface selection time, it will be chosen as the active interface.
INT wfIRedundIfActive	1.3.6.1.4.1.18.3.5.1.10.1.1.7	INTEGER	read-only	Active flag, indicates if this interface is the current active interface for the Interface Redundancy Group, or a standby interface, or not available to be used as active interface.
OCT wfIRedundIfMACAddr	1.3.6.1.4.1.18.3.5.1.10.1.1.8	OCTET STRING	read-only	MAC Address being used by Interface Redundancy as Primary MAC Address.

RFC description

Configures interface redundancy groups with hot standby functionality on Wellfleet routers.

Start monitoring Wellfleet Communications (Bay Networks) routers (interface-redundancy active/standby-failover status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-IREDUND-MIB

What Is Wellfleet-IREDUND-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description