All MIBs › Wellfleet-DSX3-MIB
Category: Wellfleet BayNetworks WAN Interfaces
Description: Monitors Wellfleet DSX-3 digital cross-connect parameters and DS3 interface performance statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Wellfleet-DSX3-MIB?
Wellfleet-DSX3-MIB is a proprietary MIB from Wellfleet Communications/Bay Networks covering the DSX-3 digital cross-connect function and DS3 (T3) interface performance on its routers. It exposes configuration objects for the cross-connect mapping and performance statistics such as line errors, framing errors, and other DS3-layer counters for each DS3 interface/channel. It is primarily a hardware/line-performance monitoring MIB: administrators use it to watch DS3 error-second and signal-quality counters to detect a degrading physical circuit before it causes an outage. It parallels, and likely predates broad deployment of, the IETF standard DS3/DSX3 MIB conventions for T3 interface monitoring. It was typically deployed on Wellfleet/Bay Networks routers terminating DS3 (45 Mbps) WAN circuits, such as in telco or large enterprise WAN edge deployments. Engineers can download the Wellfleet-DSX3-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-DSX3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Wellfleet/Bay Networks router with DS3/DSX-3 interfaces (legacy)
Monitoring Examples
No sample objects were provided, so this is inferred: an administrator would poll DS3 line-error counters (e.g., framing errors, line code violations) for each DSX-3 channel to check circuit quality. A sudden increase in error-second counts on one DS3 channel, without a change in configuration, would point to a physical-layer problem such as a degrading cable, connector, or carrier-side circuit issue.
What Can Be Monitored
- DS3 line/framing error counts
- DSX-3 cross-connect configuration
- DS3 interface signal quality statistics
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Gauge |
From RFC1213-MIB
| DisplayString |
From Wellfleet-COMMON-MIB
| wfDsx3Group | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wfDsx3ConfigTable | 1.3.6.1.4.1.18.3.4.26.1 | not-accessible | The DS3/E3 Configuration table | |
| wfDsx3ConfigEntry | 1.3.6.1.4.1.18.3.4.26.1.1 | not-accessible | per circuit DS3/E3 configuration objects; wfDsx3LineIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3LineIndex | 1.3.6.1.4.1.18.3.4.26.1.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3IfIndex | 1.3.6.1.4.1.18.3.4.26.1.1.2 | INTEGER | read-only | this is value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| INT wfDsx3TimeElapsed | 1.3.6.1.4.1.18.3.4.26.1.1.3 | INTEGER | read-only | 0..899 seconds elapsed within the current 15-minute interval |
| INT wfDsx3ValidIntervals | 1.3.6.1.4.1.18.3.4.26.1.1.4 | INTEGER | read-only | 0..96 previous intervals that valid data were collected. This is 96 unless the device was brought on line within the last 24 hours. |
| INT wfDsx3LineType | 1.3.6.1.4.1.18.3.4.26.1.1.5 | INTEGER | read-only | the variety of DS3/E3 application implementing this circuit |
| INT wfDsx3LineCoding | 1.3.6.1.4.1.18.3.4.26.1.1.6 | INTEGER | read-only | the variety of Zero Code Suppression used on the link |
| INT wfDsx3SendCode | 1.3.6.1.4.1.18.3.4.26.1.1.7 | INTEGER | read-only | the type of code being sent across the DS3/E3 circuit by the device |
| STR wfDsx3CircuitIdentifier | 1.3.6.1.4.1.18.3.4.26.1.1.8 | DisplayString | read-only | the transmission vendor's circuit identifier |
| INT wfDsx3LoopbackConfig | 1.3.6.1.4.1.18.3.4.26.1.1.9 | INTEGER | read-only | the loopback configuration of the DS3/E3 interface |
| INT wfDsx3LineStatus | 1.3.6.1.4.1.18.3.4.26.1.1.10 | INTEGER | read-only | the status of the DS3/E3 line |
| INT wfDsx3TransmitClockSource | 1.3.6.1.4.1.18.3.4.26.1.1.11 | INTEGER | read-only | the source of Transmit Clock for the DS3/E3 interface |
| wfDsx3CurrentTable | 1.3.6.1.4.1.18.3.4.26.2 | not-accessible | The DS3/E3 Current table | |
| wfDsx3CurrentEntry | 1.3.6.1.4.1.18.3.4.26.2.1 | not-accessible | per circuit DS3/E3 current objects - wfDsx3CurrentIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3CurrentIndex | 1.3.6.1.4.1.18.3.4.26.2.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3CurrentPESs | 1.3.6.1.4.1.18.3.4.26.2.1.2 | Gauge | read-only | the number of P-bit Errored Seconds in the current interval |
| GAU wfDsx3CurrentPSESs | 1.3.6.1.4.1.18.3.4.26.2.1.3 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the current interval |
| GAU wfDsx3CurrentSEFSs | 1.3.6.1.4.1.18.3.4.26.2.1.4 | Gauge | read-only | the number of Severely Errored Framing Seconds in the current interval |
| GAU wfDsx3CurrentUASs | 1.3.6.1.4.1.18.3.4.26.2.1.5 | Gauge | read-only | the number of Unavailable Seconds in the current interval |
| GAU wfDsx3CurrentLCVs | 1.3.6.1.4.1.18.3.4.26.2.1.6 | Gauge | read-only | the number of Line Coding Violations in the current interval |
| GAU wfDsx3CurrentPCVs | 1.3.6.1.4.1.18.3.4.26.2.1.7 | Gauge | read-only | the number of P-bit Coding Violations in the current interval |
| GAU wfDsx3CurrentLESs | 1.3.6.1.4.1.18.3.4.26.2.1.8 | Gauge | read-only | the number of Line Errored Seconds in the current interval |
| GAU wfDsx3CurrentCCVs | 1.3.6.1.4.1.18.3.4.26.2.1.9 | Gauge | read-only | the number of C-bit Coding Violations in the current interval |
| GAU wfDsx3CurrentCESs | 1.3.6.1.4.1.18.3.4.26.2.1.10 | Gauge | read-only | the number of C-bit Errored Seconds in the current interval |
| GAU wfDsx3CurrentCSESs | 1.3.6.1.4.1.18.3.4.26.2.1.11 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the current interval |
| GAU wfDsx3CurrentSASs | 1.3.6.1.4.1.18.3.4.26.2.1.12 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the current interval |
| GAU wfDsx3CurrentAISSs | 1.3.6.1.4.1.18.3.4.26.2.1.13 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the current interval |
| GAU wfDsx3CurrentFCs | 1.3.6.1.4.1.18.3.4.26.2.1.14 | Gauge | read-only | the number of Path Failure Count error events detected in the current interval |
| INT wfDsx3CurrentTimeElapsed | 1.3.6.1.4.1.18.3.4.26.2.1.15 | INTEGER | read-only | the number of seconds since the beginning of the far end current interval |
| INT wfDsx3CurrentValidIntervals | 1.3.6.1.4.1.18.3.4.26.2.1.16 | INTEGER | read-only | the number of previous far end intervals for which valid data is available |
| INT wfDsx3CurrentValidFlag | 1.3.6.1.4.1.18.3.4.26.2.1.17 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3IntervalTable | 1.3.6.1.4.1.18.3.4.26.3 | not-accessible | The DS3/E3 Interval table | |
| wfDsx3IntervalEntry | 1.3.6.1.4.1.18.3.4.26.3.1 | not-accessible | per circuit DS3/E3 interval objects - wfDsx3IntervalIndex corresponds to Wellfleet circuit number, wfDsx3IntervalNumber is the numbered previous 15-minute interval | |
| INT wfDsx3IntervalIndex | 1.3.6.1.4.1.18.3.4.26.3.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3IntervalNumber | 1.3.6.1.4.1.18.3.4.26.3.1.2 | INTEGER | read-only | 1..96 where 1 is the most recent 15-minute interval and 96 is the least |
| GAU wfDsx3IntervalPESs | 1.3.6.1.4.1.18.3.4.26.3.1.3 | Gauge | read-only | the number of P-bit Errored Seconds in the specified interval |
| GAU wfDsx3IntervalPSESs | 1.3.6.1.4.1.18.3.4.26.3.1.4 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3IntervalSEFSs | 1.3.6.1.4.1.18.3.4.26.3.1.5 | Gauge | read-only | the number of Severely Errored Framing Seconds in the specified interval |
| GAU wfDsx3IntervalUASs | 1.3.6.1.4.1.18.3.4.26.3.1.6 | Gauge | read-only | the number of Unavailable Seconds in the specified interval |
| GAU wfDsx3IntervalLCVs | 1.3.6.1.4.1.18.3.4.26.3.1.7 | Gauge | read-only | the number of Line Coding Violations in the specified interval |
| GAU wfDsx3IntervalPCVs | 1.3.6.1.4.1.18.3.4.26.3.1.8 | Gauge | read-only | the number of P-bit Coding Violations in the specified interval |
| GAU wfDsx3IntervalLESs | 1.3.6.1.4.1.18.3.4.26.3.1.9 | Gauge | read-only | the number of Line Errored Seconds in the specified interval |
| GAU wfDsx3IntervalCCVs | 1.3.6.1.4.1.18.3.4.26.3.1.10 | Gauge | read-only | the number of C-bit Coding Violations in the specified interval |
| GAU wfDsx3IntervalCESs | 1.3.6.1.4.1.18.3.4.26.3.1.11 | Gauge | read-only | the number of C-bit Errored Seconds in the specified interval |
| GAU wfDsx3IntervalCSESs | 1.3.6.1.4.1.18.3.4.26.3.1.12 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3IntervalSASs | 1.3.6.1.4.1.18.3.4.26.3.1.13 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the specified interval |
| GAU wfDsx3IntervalAISSs | 1.3.6.1.4.1.18.3.4.26.3.1.14 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the specified interval |
| GAU wfDsx3IntervalFCs | 1.3.6.1.4.1.18.3.4.26.3.1.15 | Gauge | read-only | the number of Path Failure Count error events detected in the specified interval |
| INT wfDsx3IntervalValidFlag | 1.3.6.1.4.1.18.3.4.26.3.1.16 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3TotalTable | 1.3.6.1.4.1.18.3.4.26.4 | not-accessible | The DS3/E3 Total table | |
| wfDsx3TotalEntry | 1.3.6.1.4.1.18.3.4.26.4.1 | not-accessible | per circuit DS3/E3 total objects - wfDsx3TotalIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3TotalIndex | 1.3.6.1.4.1.18.3.4.26.4.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3TotalPESs | 1.3.6.1.4.1.18.3.4.26.4.1.2 | Gauge | read-only | the number of P-bit Errored Seconds in the last 24 hours |
| GAU wfDsx3TotalPSESs | 1.3.6.1.4.1.18.3.4.26.4.1.3 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the last 24 hours |
| GAU wfDsx3TotalSEFSs | 1.3.6.1.4.1.18.3.4.26.4.1.4 | Gauge | read-only | the number of Severely Errored Framing Seconds in the last 24 hours |
| GAU wfDsx3TotalUASs | 1.3.6.1.4.1.18.3.4.26.4.1.5 | Gauge | read-only | the number of Unavailable Seconds in the last 24 hours |
| GAU wfDsx3TotalLCVs | 1.3.6.1.4.1.18.3.4.26.4.1.6 | Gauge | read-only | the number of Line Coding Violations in the last 24 hours |
| GAU wfDsx3TotalPCVs | 1.3.6.1.4.1.18.3.4.26.4.1.7 | Gauge | read-only | the number of P-bit Coding Violations in the last 24 hours |
| GAU wfDsx3TotalLESs | 1.3.6.1.4.1.18.3.4.26.4.1.8 | Gauge | read-only | the number of Line Errored Seconds in the last 24 hours |
| GAU wfDsx3TotalCCVs | 1.3.6.1.4.1.18.3.4.26.4.1.9 | Gauge | read-only | the number of C-bit Coding Violations in the last 24 hours |
| GAU wfDsx3TotalCESs | 1.3.6.1.4.1.18.3.4.26.4.1.10 | Gauge | read-only | the number of C-bit Errored Seconds in the last 24 hours |
| GAU wfDsx3TotalCSESs | 1.3.6.1.4.1.18.3.4.26.4.1.11 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the last 24 hours |
| GAU wfDsx3TotalSASs | 1.3.6.1.4.1.18.3.4.26.4.1.12 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the last 24 hours |
| GAU wfDsx3TotalAISSs | 1.3.6.1.4.1.18.3.4.26.4.1.13 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the last 24 hours |
| GAU wfDsx3TotalFCs | 1.3.6.1.4.1.18.3.4.26.4.1.14 | Gauge | read-only | the number of Path Failure Count error events detected in the last 24 hours |
| INT wfDsx3TotalValidFlag | 1.3.6.1.4.1.18.3.4.26.4.1.15 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndConfigTable | 1.3.6.1.4.1.18.3.4.26.5 | not-accessible | The DS3/E3 Far End Configuration table | |
| wfDsx3FarEndConfigEntry | 1.3.6.1.4.1.18.3.4.26.5.1 | not-accessible | per circuit DS3/E3 far end config objects - wfDsx3FarEndLineIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3FarEndLineIndex | 1.3.6.1.4.1.18.3.4.26.5.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| STR wfDsx3FarEndEquipCode | 1.3.6.1.4.1.18.3.4.26.5.1.2 | DisplayString | read-write | equipment description code - C-bit parity only |
| STR wfDsx3FarEndLocationIDCode | 1.3.6.1.4.1.18.3.4.26.5.1.3 | DisplayString | read-write | equipment location code - C-bit parity only |
| STR wfDsx3FarEndFrameIDCode | 1.3.6.1.4.1.18.3.4.26.5.1.4 | DisplayString | read-write | code for the equipment location within a building |
| STR wfDsx3FarEndUnitCode | 1.3.6.1.4.1.18.3.4.26.5.1.5 | DisplayString | read-write | code for the equipment location within a bay |
| STR wfDsx3FarEndFacilityIDCode | 1.3.6.1.4.1.18.3.4.26.5.1.6 | DisplayString | read-write | path identification code |
| wfDsx3FarEndCurrentTable | 1.3.6.1.4.1.18.3.4.26.6 | not-accessible | The DS3/E3 Far End Current table | |
| wfDsx3FarEndCurrentEntry | 1.3.6.1.4.1.18.3.4.26.6.1 | not-accessible | per circuit DS3/E3 far end current objects wfDsx3FarEndCurrentIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3FarEndCurrentIndex | 1.3.6.1.4.1.18.3.4.26.6.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3FarEndTimeElapsed | 1.3.6.1.4.1.18.3.4.26.6.1.2 | INTEGER | read-only | the number of seconds since the beginning of the far end current interval |
| INT wfDsx3FarEndValidIntervals | 1.3.6.1.4.1.18.3.4.26.6.1.3 | INTEGER | read-only | the number of previous far end intervals for which valid data is available |
| GAU wfDsx3FarEndCurrentCESs | 1.3.6.1.4.1.18.3.4.26.6.1.4 | Gauge | read-only | the number of C-bit Errored Seconds in the current far end interval |
| GAU wfDsx3FarEndCurrentCSESs | 1.3.6.1.4.1.18.3.4.26.6.1.5 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the current far end interval |
| GAU wfDsx3FarEndCurrentCCVs | 1.3.6.1.4.1.18.3.4.26.6.1.6 | Gauge | read-only | the number of C-bit Coding Violations in the current far end interval |
| GAU wfDsx3FarEndCurrentUASs | 1.3.6.1.4.1.18.3.4.26.6.1.7 | Gauge | read-only | the number of Unavailable Seconds in the current far end interval |
| GAU wfDsx3FarEndCurrentSASs | 1.3.6.1.4.1.18.3.4.26.6.1.8 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the current far end interval |
| GAU wfDsx3FarEndCurrentFCs | 1.3.6.1.4.1.18.3.4.26.6.1.9 | Gauge | read-only | the number of Path Failure Count error events detected in the current far end interval |
| INT wfDsx3FarEndCurrentValidFlag | 1.3.6.1.4.1.18.3.4.26.6.1.10 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndIntervalTable | 1.3.6.1.4.1.18.3.4.26.7 | not-accessible | The DS3/E3 Far End Interval table | |
| wfDsx3FarEndIntervalEntry | 1.3.6.1.4.1.18.3.4.26.7.1 | not-accessible | per circuit DS3/E3 far end interval objects - wfDsx3FarEndIntervalIndex corresponds to Wellfleet circuit number, wfDsx3FarEndIntervalNumber is the numbered previous 15-minute interval | |
| INT wfDsx3FarEndIntervalIndex | 1.3.6.1.4.1.18.3.4.26.7.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3FarEndIntervalNumber | 1.3.6.1.4.1.18.3.4.26.7.1.2 | INTEGER | read-only | 1..96 where 1 is the most recent 15-minute interval and 96 is the least |
| GAU wfDsx3FarEndIntervalCESs | 1.3.6.1.4.1.18.3.4.26.7.1.3 | Gauge | read-only | the count of C-bit Errored Seconds in the specified interval |
| GAU wfDsx3FarEndIntervalCSESs | 1.3.6.1.4.1.18.3.4.26.7.1.4 | Gauge | read-only | the count of C-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3FarEndIntervalCCVs | 1.3.6.1.4.1.18.3.4.26.7.1.5 | Gauge | read-only | the count of C-bit Code Violation error events in the specified interval |
| GAU wfDsx3FarEndIntervalUASs | 1.3.6.1.4.1.18.3.4.26.7.1.6 | Gauge | read-only | the count of Unavailable Seconds in the specified interval |
| GAU wfDsx3FarEndIntervalSASs | 1.3.6.1.4.1.18.3.4.26.7.1.7 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the specified far end interval |
| GAU wfDsx3FarEndIntervalFCs | 1.3.6.1.4.1.18.3.4.26.7.1.8 | Gauge | read-only | the number of Path Failure Count error events detected in the specified far end interval |
| INT wfDsx3FarEndIntervalValidFlag | 1.3.6.1.4.1.18.3.4.26.7.1.9 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndTotalTable | 1.3.6.1.4.1.18.3.4.26.8 | not-accessible | The DS3/E3 Far End Total table | |
| wfDsx3FarEndTotalEntry | 1.3.6.1.4.1.18.3.4.26.8.1 | not-accessible | per circuit far end DS3/E3 total objects - wfDsx3FarEndTotalIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3FarEndTotalIndex | 1.3.6.1.4.1.18.3.4.26.8.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3FarEndTotalCESs | 1.3.6.1.4.1.18.3.4.26.8.1.2 | Gauge | read-only | total count of C-bit Errored Seconds |
| GAU wfDsx3FarEndTotalCSESs | 1.3.6.1.4.1.18.3.4.26.8.1.3 | Gauge | read-only | total count of C-bit Severely Errored Seconds |
| GAU wfDsx3FarEndTotalCCVs | 1.3.6.1.4.1.18.3.4.26.8.1.4 | Gauge | read-only | total count of C-bit Code Violation error events |
| GAU wfDsx3FarEndTotalUASs | 1.3.6.1.4.1.18.3.4.26.8.1.5 | Gauge | read-only | total count of Unavailable Seconds |
| GAU wfDsx3FarEndTotalSASs | 1.3.6.1.4.1.18.3.4.26.8.1.6 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects at the far end in the last 24 hours. |
| GAU wfDsx3FarEndTotalFCs | 1.3.6.1.4.1.18.3.4.26.8.1.7 | Gauge | read-only | the number of Path Failure Count error events detected at the far end in the last 24 hours. |
| INT wfDsx3FarEndTotalValidFlag | 1.3.6.1.4.1.18.3.4.26.8.1.8 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfAtmInterfaceDs3PlcpTable | 1.3.6.1.4.1.18.3.4.26.9 | not-accessible | The Atm Interface DS3 PLCP table | |
| wfAtmInterfaceDs3PlcpEntry | 1.3.6.1.4.1.18.3.4.26.9.1 | not-accessible | This table contains ATM interface DS3 PLCP parameters and state variables, one entry per ATM interface port. | |
| INT wfAtmInterfaceDs3PlcpIndex | 1.3.6.1.4.1.18.3.4.26.9.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfAtmInterfaceDs3PlcpSEFSs | 1.3.6.1.4.1.18.3.4.26.9.1.2 | Gauge | read-only | the number of DS3 PLCP Severely Errored Framing Second (SEFS) |
| INT wfAtmInterfaceDs3PlcpAlarmState | 1.3.6.1.4.1.18.3.4.26.9.1.3 | INTEGER | read-only | the state of the DS3 PLCP |
| GAU wfAtmInterfaceDs3PlcpUASs | 1.3.6.1.4.1.18.3.4.26.9.1.4 | Gauge | read-only | the number of Unavailable Seconds encountered by the PLCP |
| wfDsx3DayCurrentTable | 1.3.6.1.4.1.18.3.4.26.11 | not-accessible | The DS3/E3 Current table | |
| wfDsx3DayCurrentEntry | 1.3.6.1.4.1.18.3.4.26.11.1 | not-accessible | per circuit DS3/E3 current objects - wfDsx3DayCurrentIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3DayCurrentIndex | 1.3.6.1.4.1.18.3.4.26.11.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3DayCurrentPESs | 1.3.6.1.4.1.18.3.4.26.11.1.2 | Gauge | read-only | the number of P-bit Errored Seconds in the current interval |
| GAU wfDsx3DayCurrentPSESs | 1.3.6.1.4.1.18.3.4.26.11.1.3 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the current interval |
| GAU wfDsx3DayCurrentSEFSs | 1.3.6.1.4.1.18.3.4.26.11.1.4 | Gauge | read-only | the number of Severely Errored Framing Seconds in the current interval |
| GAU wfDsx3DayCurrentUASs | 1.3.6.1.4.1.18.3.4.26.11.1.5 | Gauge | read-only | the number of Unavailable Seconds in the current interval |
| GAU wfDsx3DayCurrentLCVs | 1.3.6.1.4.1.18.3.4.26.11.1.6 | Gauge | read-only | the number of Line Coding Violations in the current interval |
| GAU wfDsx3DayCurrentPCVs | 1.3.6.1.4.1.18.3.4.26.11.1.7 | Gauge | read-only | the number of P-bit Coding Violations in the current interval |
| GAU wfDsx3DayCurrentLESs | 1.3.6.1.4.1.18.3.4.26.11.1.8 | Gauge | read-only | the number of Line Errored Seconds in the current interval |
| GAU wfDsx3DayCurrentCCVs | 1.3.6.1.4.1.18.3.4.26.11.1.9 | Gauge | read-only | the number of C-bit Coding Violations in the current interval |
| GAU wfDsx3DayCurrentCESs | 1.3.6.1.4.1.18.3.4.26.11.1.10 | Gauge | read-only | the number of C-bit Errored Seconds in the current interval |
| GAU wfDsx3DayCurrentCSESs | 1.3.6.1.4.1.18.3.4.26.11.1.11 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the current interval |
| GAU wfDsx3DayCurrentSASs | 1.3.6.1.4.1.18.3.4.26.11.1.12 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the current interval |
| GAU wfDsx3DayCurrentAISSs | 1.3.6.1.4.1.18.3.4.26.11.1.13 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the current interval |
| GAU wfDsx3DayCurrentFCs | 1.3.6.1.4.1.18.3.4.26.11.1.14 | Gauge | read-only | the number of Path Failure Count error events detected in the current interval |
| INT wfDsx3DayCurrentTimeElapsed | 1.3.6.1.4.1.18.3.4.26.11.1.15 | INTEGER | read-only | the number of seconds since the beginning of the far end current interval |
| INT wfDsx3DayCurrentValidIntervals | 1.3.6.1.4.1.18.3.4.26.11.1.16 | INTEGER | read-only | the number of previous far end intervals for which valid data is available |
| INT wfDsx3DayCurrentValidFlag | 1.3.6.1.4.1.18.3.4.26.11.1.17 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3DayIntervalTable | 1.3.6.1.4.1.18.3.4.26.12 | not-accessible | The DS3/E3 Interval table | |
| wfDsx3DayIntervalEntry | 1.3.6.1.4.1.18.3.4.26.12.1 | not-accessible | per circuit DS3/E3 interval objects - wfDsx3DayIntervalIndex corresponds to Wellfleet circuit number, wfDsx3DayIntervalNumber is the numbered previous 15-minute interval | |
| INT wfDsx3DayIntervalIndex | 1.3.6.1.4.1.18.3.4.26.12.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3DayIntervalNumber | 1.3.6.1.4.1.18.3.4.26.12.1.2 | INTEGER | read-only | 1..96 where 1 is the most recent 15-minute interval and 96 is the least |
| GAU wfDsx3DayIntervalPESs | 1.3.6.1.4.1.18.3.4.26.12.1.3 | Gauge | read-only | the number of P-bit Errored Seconds in the specified interval |
| GAU wfDsx3DayIntervalPSESs | 1.3.6.1.4.1.18.3.4.26.12.1.4 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3DayIntervalSEFSs | 1.3.6.1.4.1.18.3.4.26.12.1.5 | Gauge | read-only | the number of Severely Errored Framing Seconds in the specified interval |
| GAU wfDsx3DayIntervalUASs | 1.3.6.1.4.1.18.3.4.26.12.1.6 | Gauge | read-only | the number of Unavailable Seconds in the specified interval |
| GAU wfDsx3DayIntervalLCVs | 1.3.6.1.4.1.18.3.4.26.12.1.7 | Gauge | read-only | the number of Line Coding Violations in the specified interval |
| GAU wfDsx3DayIntervalPCVs | 1.3.6.1.4.1.18.3.4.26.12.1.8 | Gauge | read-only | the number of P-bit Coding Violations in the specified interval |
| GAU wfDsx3DayIntervalLESs | 1.3.6.1.4.1.18.3.4.26.12.1.9 | Gauge | read-only | the number of Line Errored Seconds in the specified interval |
| GAU wfDsx3DayIntervalCCVs | 1.3.6.1.4.1.18.3.4.26.12.1.10 | Gauge | read-only | the number of C-bit Coding Violations in the specified interval |
| GAU wfDsx3DayIntervalCESs | 1.3.6.1.4.1.18.3.4.26.12.1.11 | Gauge | read-only | the number of C-bit Errored Seconds in the specified interval |
| GAU wfDsx3DayIntervalCSESs | 1.3.6.1.4.1.18.3.4.26.12.1.12 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3DayIntervalSASs | 1.3.6.1.4.1.18.3.4.26.12.1.13 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the specified interval |
| GAU wfDsx3DayIntervalAISSs | 1.3.6.1.4.1.18.3.4.26.12.1.14 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the specified interval |
| GAU wfDsx3DayIntervalFCs | 1.3.6.1.4.1.18.3.4.26.12.1.15 | Gauge | read-only | the number of Path Failure Count error events detected in the specified interval |
| INT wfDsx3DayIntervalValidFlag | 1.3.6.1.4.1.18.3.4.26.12.1.16 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3DayTotalTable | 1.3.6.1.4.1.18.3.4.26.13 | not-accessible | The DS3/E3 Total table | |
| wfDsx3DayTotalEntry | 1.3.6.1.4.1.18.3.4.26.13.1 | not-accessible | per circuit DS3/E3 total objects - wfDsx3DayTotalIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3DayTotalIndex | 1.3.6.1.4.1.18.3.4.26.13.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3DayTotalPESs | 1.3.6.1.4.1.18.3.4.26.13.1.2 | Gauge | read-only | the number of P-bit Errored Seconds in the last 24 hours |
| GAU wfDsx3DayTotalPSESs | 1.3.6.1.4.1.18.3.4.26.13.1.3 | Gauge | read-only | the number of P-bit Severely Errored Seconds in the last 24 hours |
| GAU wfDsx3DayTotalSEFSs | 1.3.6.1.4.1.18.3.4.26.13.1.4 | Gauge | read-only | the number of Severely Errored Framing Seconds in the last 24 hours |
| GAU wfDsx3DayTotalUASs | 1.3.6.1.4.1.18.3.4.26.13.1.5 | Gauge | read-only | the number of Unavailable Seconds in the last 24 hours |
| GAU wfDsx3DayTotalLCVs | 1.3.6.1.4.1.18.3.4.26.13.1.6 | Gauge | read-only | the number of Line Coding Violations in the last 24 hours |
| GAU wfDsx3DayTotalPCVs | 1.3.6.1.4.1.18.3.4.26.13.1.7 | Gauge | read-only | the number of P-bit Coding Violations in the last 24 hours |
| GAU wfDsx3DayTotalLESs | 1.3.6.1.4.1.18.3.4.26.13.1.8 | Gauge | read-only | the number of Line Errored Seconds in the last 24 hours |
| GAU wfDsx3DayTotalCCVs | 1.3.6.1.4.1.18.3.4.26.13.1.9 | Gauge | read-only | the number of C-bit Coding Violations in the last 24 hours |
| GAU wfDsx3DayTotalCESs | 1.3.6.1.4.1.18.3.4.26.13.1.10 | Gauge | read-only | the number of C-bit Errored Seconds in the last 24 hours |
| GAU wfDsx3DayTotalCSESs | 1.3.6.1.4.1.18.3.4.26.13.1.11 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the last 24 hours |
| GAU wfDsx3DayTotalSASs | 1.3.6.1.4.1.18.3.4.26.13.1.12 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the last 24 hours |
| GAU wfDsx3DayTotalAISSs | 1.3.6.1.4.1.18.3.4.26.13.1.13 | Gauge | read-only | the number of Seconds containing one or more AIS defect in the last 24 hours |
| GAU wfDsx3DayTotalFCs | 1.3.6.1.4.1.18.3.4.26.13.1.14 | Gauge | read-only | the number of Path Failure Count error events detected in the last 24 hours |
| INT wfDsx3DayTotalValidFlag | 1.3.6.1.4.1.18.3.4.26.13.1.15 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndDayCurrentTable | 1.3.6.1.4.1.18.3.4.26.14 | not-accessible | The DS3/E3 Far End Current table | |
| wfDsx3FarEndDayCurrentEntry | 1.3.6.1.4.1.18.3.4.26.14.1 | not-accessible | per circuit DS3/E3 far end current objects wfDsx3FarEndDayCurrentIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3FarEndDayCurrentIndex | 1.3.6.1.4.1.18.3.4.26.14.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3FarEndDayTimeElapsed | 1.3.6.1.4.1.18.3.4.26.14.1.2 | INTEGER | read-only | the number of seconds since the beginning of the far end current interval |
| INT wfDsx3FarEndDayValidIntervals | 1.3.6.1.4.1.18.3.4.26.14.1.3 | INTEGER | read-only | the number of previous far end intervals for which valid data is available |
| GAU wfDsx3FarEndDayCurrentCESs | 1.3.6.1.4.1.18.3.4.26.14.1.4 | Gauge | read-only | the number of C-bit Errored Seconds in the current far end interval |
| GAU wfDsx3FarEndDayCurrentCSESs | 1.3.6.1.4.1.18.3.4.26.14.1.5 | Gauge | read-only | the number of C-bit Severely Errored Seconds in the current far end interval |
| GAU wfDsx3FarEndDayCurrentCCVs | 1.3.6.1.4.1.18.3.4.26.14.1.6 | Gauge | read-only | the number of C-bit Coding Violations in the current far end interval |
| GAU wfDsx3FarEndDayCurrentUASs | 1.3.6.1.4.1.18.3.4.26.14.1.7 | Gauge | read-only | the number of Unavailable Seconds in the current far end interval |
| GAU wfDsx3FarEndDayCurrentSASs | 1.3.6.1.4.1.18.3.4.26.14.1.8 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the current far end interval |
| GAU wfDsx3FarEndDayCurrentFCs | 1.3.6.1.4.1.18.3.4.26.14.1.9 | Gauge | read-only | the number of Path Failure Count error events detected in the current far end interval |
| INT wfDsx3FarEndDayCurrentValidFlag | 1.3.6.1.4.1.18.3.4.26.14.1.10 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndDayIntervalTable | 1.3.6.1.4.1.18.3.4.26.15 | not-accessible | The DS3/E3 Far End Interval table | |
| wfDsx3FarEndDayIntervalEntry | 1.3.6.1.4.1.18.3.4.26.15.1 | not-accessible | per circuit DS3/E3 far end interval objects - wfDsx3FarEndDayIntervalIndex corresponds to Wellfleet circuit number, wfDsx3FarEndDayIntervalNumber is the numbered previous 15-minute interval | |
| INT wfDsx3FarEndDayIntervalIndex | 1.3.6.1.4.1.18.3.4.26.15.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| INT wfDsx3FarEndDayIntervalNumber | 1.3.6.1.4.1.18.3.4.26.15.1.2 | INTEGER | read-only | 1..96 where 1 is the most recent 15-minute interval and 96 is the least |
| GAU wfDsx3FarEndDayIntervalCESs | 1.3.6.1.4.1.18.3.4.26.15.1.3 | Gauge | read-only | the count of C-bit Errored Seconds in the specified interval |
| GAU wfDsx3FarEndDayIntervalCSESs | 1.3.6.1.4.1.18.3.4.26.15.1.4 | Gauge | read-only | the count of C-bit Severely Errored Seconds in the specified interval |
| GAU wfDsx3FarEndDayIntervalCCVs | 1.3.6.1.4.1.18.3.4.26.15.1.5 | Gauge | read-only | the count of C-bit Code Violation error events in the specified interval |
| GAU wfDsx3FarEndDayIntervalUASs | 1.3.6.1.4.1.18.3.4.26.15.1.6 | Gauge | read-only | the count of Unavailable Seconds in the specified interval |
| GAU wfDsx3FarEndDayIntervalSASs | 1.3.6.1.4.1.18.3.4.26.15.1.7 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects in the specified far end interval |
| GAU wfDsx3FarEndDayIntervalFCs | 1.3.6.1.4.1.18.3.4.26.15.1.8 | Gauge | read-only | the number of Path Failure Count error events detected in the specified far end interval |
| INT wfDsx3FarEndDayIntervalValidFlag | 1.3.6.1.4.1.18.3.4.26.15.1.9 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3FarEndDayTotalTable | 1.3.6.1.4.1.18.3.4.26.16 | not-accessible | The DS3/E3 Far End Total table | |
| wfDsx3FarEndDayTotalEntry | 1.3.6.1.4.1.18.3.4.26.16.1 | not-accessible | per circuit far end DS3/E3 total objects - wfDsx3FarEndDayTotalIndex corresponds to Wellfleet circuit number | |
| INT wfDsx3FarEndDayTotalIndex | 1.3.6.1.4.1.18.3.4.26.16.1.1 | INTEGER | read-only | this corresponds to the Wellfleet circuit number |
| GAU wfDsx3FarEndDayTotalCESs | 1.3.6.1.4.1.18.3.4.26.16.1.2 | Gauge | read-only | total count of C-bit Errored Seconds |
| GAU wfDsx3FarEndDayTotalCSESs | 1.3.6.1.4.1.18.3.4.26.16.1.3 | Gauge | read-only | total count of C-bit Severely Errored Seconds |
| GAU wfDsx3FarEndDayTotalCCVs | 1.3.6.1.4.1.18.3.4.26.16.1.4 | Gauge | read-only | total count of C-bit Code Violation error events |
| GAU wfDsx3FarEndDayTotalUASs | 1.3.6.1.4.1.18.3.4.26.16.1.5 | Gauge | read-only | total count of Unavailable Seconds |
| GAU wfDsx3FarEndDayTotalSASs | 1.3.6.1.4.1.18.3.4.26.16.1.6 | Gauge | read-only | the number of Seconds containing one or more SEFs or AIS defects at the far end in the last 24 hours. |
| GAU wfDsx3FarEndDayTotalFCs | 1.3.6.1.4.1.18.3.4.26.16.1.7 | Gauge | read-only | the number of Path Failure Count error events detected at the far end in the last 24 hours. |
| INT wfDsx3FarEndDayTotalValidFlag | 1.3.6.1.4.1.18.3.4.26.16.1.8 | INTEGER | read-only | Indicates whether this interval reported by the Mib Table is valid or invalid. |
| wfDsx3ThrAlrtTable | 1.3.6.1.4.1.18.3.4.26.18 | not-accessible | Current statistics Alarm Threshold Crossing table. | |
| wfDsx3ThrAlrtEntry | 1.3.6.1.4.1.18.3.4.26.18.1 | not-accessible | An entry in the Dsx3 ThrAlrt table | |
| INT wfDsx3ThrAlrtDelete | 1.3.6.1.4.1.18.3.4.26.18.1.1 | INTEGER | read-write | Create/Delete parameter |
| INT wfDsx3ThrAlrtIndex | 1.3.6.1.4.1.18.3.4.26.18.1.2 | INTEGER | read-only | The instance ID that identifies the port. |
| GAU wfDsx3ThrAlrtPESs | 1.3.6.1.4.1.18.3.4.26.18.1.3 | Gauge | read-write | The number of P-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtPSESs | 1.3.6.1.4.1.18.3.4.26.18.1.4 | Gauge | read-write | The number of P-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtSEFSs | 1.3.6.1.4.1.18.3.4.26.18.1.5 | Gauge | read-write | The number of Severely Errored Framing Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtUASs | 1.3.6.1.4.1.18.3.4.26.18.1.6 | Gauge | read-write | The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtLCVs | 1.3.6.1.4.1.18.3.4.26.18.1.7 | Gauge | read-write | The number of Line Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtPCVs | 1.3.6.1.4.1.18.3.4.26.18.1.8 | Gauge | read-write | The number of P-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtLESs | 1.3.6.1.4.1.18.3.4.26.18.1.9 | Gauge | read-write | The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtCCVs | 1.3.6.1.4.1.18.3.4.26.18.1.10 | Gauge | read-write | The number of C-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtCESs | 1.3.6.1.4.1.18.3.4.26.18.1.11 | Gauge | read-write | The number of C-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtCSESs | 1.3.6.1.4.1.18.3.4.26.18.1.12 | Gauge | read-write | The number of C-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtSASs | 1.3.6.1.4.1.18.3.4.26.18.1.13 | Gauge | read-write | The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtAISSs | 1.3.6.1.4.1.18.3.4.26.18.1.14 | Gauge | read-write | The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3ThrAlrtFCs | 1.3.6.1.4.1.18.3.4.26.18.1.15 | Gauge | read-write | The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert. |
| wfDsx3FarEndThrAlrtTable | 1.3.6.1.4.1.18.3.4.26.19 | not-accessible | Current Far End statistics Alarm Threshold Crossing table. | |
| wfDsx3FarEndThrAlrtEntry | 1.3.6.1.4.1.18.3.4.26.19.1 | not-accessible | An entry in the Dsx3 ThrAlrt table | |
| INT wfDsx3FarEndThrAlrtDelete | 1.3.6.1.4.1.18.3.4.26.19.1.1 | INTEGER | read-write | Create/Delete parameter |
| INT wfDsx3FarEndThrAlrtIndex | 1.3.6.1.4.1.18.3.4.26.19.1.2 | INTEGER | read-only | The instance ID that identifies the port. |
| GAU wfDsx3FarEndThrAlrtCESs | 1.3.6.1.4.1.18.3.4.26.19.1.3 | Gauge | read-write | The number of C-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndThrAlrtCSESs | 1.3.6.1.4.1.18.3.4.26.19.1.4 | Gauge | read-write | The number of C-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndThrAlrtCCVs | 1.3.6.1.4.1.18.3.4.26.19.1.5 | Gauge | read-write | The number of C-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndThrAlrtUASs | 1.3.6.1.4.1.18.3.4.26.19.1.6 | Gauge | read-write | The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndThrAlrtSASs | 1.3.6.1.4.1.18.3.4.26.19.1.7 | Gauge | read-write | The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndThrAlrtFCs | 1.3.6.1.4.1.18.3.4.26.19.1.8 | Gauge | read-write | The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert. |
| wfDsx3DayThrAlrtTable | 1.3.6.1.4.1.18.3.4.26.20 | not-accessible | Current Day statistics Alarm Threshold Crossing table. | |
| wfDsx3DayThrAlrtEntry | 1.3.6.1.4.1.18.3.4.26.20.1 | not-accessible | An entry in the Dsx3 ThrAlrt table | |
| INT wfDsx3DayThrAlrtDelete | 1.3.6.1.4.1.18.3.4.26.20.1.1 | INTEGER | read-write | Create/Delete parameter |
| INT wfDsx3DayThrAlrtIndex | 1.3.6.1.4.1.18.3.4.26.20.1.2 | INTEGER | read-only | The instance ID that identifies the port. |
| GAU wfDsx3DayThrAlrtPESs | 1.3.6.1.4.1.18.3.4.26.20.1.3 | Gauge | read-write | The number of P-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtPSESs | 1.3.6.1.4.1.18.3.4.26.20.1.4 | Gauge | read-write | The number of P-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtSEFSs | 1.3.6.1.4.1.18.3.4.26.20.1.5 | Gauge | read-write | The number of Severely Errored Framing Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtUASs | 1.3.6.1.4.1.18.3.4.26.20.1.6 | Gauge | read-write | The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtLCVs | 1.3.6.1.4.1.18.3.4.26.20.1.7 | Gauge | read-write | The number of Line Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtPCVs | 1.3.6.1.4.1.18.3.4.26.20.1.8 | Gauge | read-write | The number of P-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtLESs | 1.3.6.1.4.1.18.3.4.26.20.1.9 | Gauge | read-write | The number of Line Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtCCVs | 1.3.6.1.4.1.18.3.4.26.20.1.10 | Gauge | read-write | The number of C-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtCESs | 1.3.6.1.4.1.18.3.4.26.20.1.11 | Gauge | read-write | The number of C-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtCSESs | 1.3.6.1.4.1.18.3.4.26.20.1.12 | Gauge | read-write | The number of C-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtSASs | 1.3.6.1.4.1.18.3.4.26.20.1.13 | Gauge | read-write | The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtAISSs | 1.3.6.1.4.1.18.3.4.26.20.1.14 | Gauge | read-write | The number of AIS defect Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3DayThrAlrtFCs | 1.3.6.1.4.1.18.3.4.26.20.1.15 | Gauge | read-write | The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert. |
| wfDsx3FarEndDayThrAlrtTable | 1.3.6.1.4.1.18.3.4.26.21 | not-accessible | Current Far End Day statistics Alarm Threshold Crossing table. | |
| wfDsx3FarEndDayThrAlrtEntry | 1.3.6.1.4.1.18.3.4.26.21.1 | not-accessible | An entry in the Dsx3 ThrAlrt table | |
| INT wfDsx3FarEndDayThrAlrtDelete | 1.3.6.1.4.1.18.3.4.26.21.1.1 | INTEGER | read-write | Create/Delete parameter |
| INT wfDsx3FarEndDayThrAlrtIndex | 1.3.6.1.4.1.18.3.4.26.21.1.2 | INTEGER | read-only | The instance ID that identifies the port. |
| GAU wfDsx3FarEndDayThrAlrtCESs | 1.3.6.1.4.1.18.3.4.26.21.1.3 | Gauge | read-write | The number of C-bit Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndDayThrAlrtCSESs | 1.3.6.1.4.1.18.3.4.26.21.1.4 | Gauge | read-write | The number of C-bit Severely Errored Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndDayThrAlrtCCVs | 1.3.6.1.4.1.18.3.4.26.21.1.5 | Gauge | read-write | The number of C-bit Coding Violations which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndDayThrAlrtUASs | 1.3.6.1.4.1.18.3.4.26.21.1.6 | Gauge | read-write | The number of Unavailable Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndDayThrAlrtSASs | 1.3.6.1.4.1.18.3.4.26.21.1.7 | Gauge | read-write | The number of SEF/AIS Seconds which must be received prior to the generation of a Threshold Crossing Alert. |
| GAU wfDsx3FarEndDayThrAlrtFCs | 1.3.6.1.4.1.18.3.4.26.21.1.8 | Gauge | read-write | The number of Path Failure Counts which must be received prior to the generation of a Threshold Crossing Alert. |
RFC description
DS3/E3 circuit configuration and management for Wellfleet routers, including line status and performance metrics.
Start monitoring Wellfleet/Bay Networks router with DS3/DSX-3 interfaces, legacy (cross-connect mapping/error-counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.