WAN-MIB

All MIBs › WAN-MIB

Organization: Avaya Inc.

Last Updated: 2005-06-21

Category: WAN and Access

Description: Manages Avaya WAN interface parameters including link status, encapsulation settings, and traffic counters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WAN-MIB?

WAN-MIB is a vendor-specific module from Avaya for managing wide-area network interface features on WAN access devices. It exposes configuration objects for WAN link encapsulation settings alongside operational status and traffic-counter objects per WAN interface. In a monitoring context it is used to track WAN link up/down status and traffic throughput/error counters, helping an operator detect a down or flapping WAN circuit or unusually high error/discard rates on a branch link. It sits alongside the standard IF-MIB, extending the generic interface model with WAN-specific encapsulation and feature configuration rather than replacing it. It is typically deployed on Avaya WAN access routers/gateways connecting branch offices over leased lines, Frame Relay, or similar WAN circuits. Engineers can download the WAN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in WAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Avaya WAN access router/gateway

Monitoring Examples

No sample object/table names were provided for this MIB, so specific OIDs cannot be cited here. Based on its stated purpose, an admin would typically poll a WAN interface's link-status object to detect an interface going down, and its traffic-counter objects to monitor throughput and error rates on a leased-line or Frame Relay circuit. Encapsulation-configuration objects would be checked to confirm the WAN link is running the expected protocol (e.g., PPP, Frame Relay, HDLC).

What Can Be Monitored

WAN link operational status
WAN interface traffic counters
WAN encapsulation configuration
interface error/discard rates

Imported Objects

From AVAYAGEN-MIB

lsg	OBJECT-IDENTITY

From DS0BUNDLE-MIB

dsx0BundleCircuitIdentifier	OBJECT-TYPE
dsx0BundleIfIndex	OBJECT-TYPE
dsx0BundleIndex	OBJECT-TYPE
dsx0BundleRowStatus	OBJECT-TYPE

From FRAME-RELAY-DTE-MIB

DLCI

From IF-MIB

InterfaceIndex
ifAdminStatus	OBJECT-TYPE
ifAlias	OBJECT-TYPE
ifIndex	OBJECT-TYPE
ifName	OBJECT-TYPE
ifOperStatus	OBJECT-TYPE

From RFC1213-MIB

PhysAddress

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
avayaEISWan	1.3.6.1.4.1.6889.2.1.6			The mib for controlling WAN-related features of WAN access devices.
deviceSpecific	1.3.6.1.4.1.6889.2.1.6.1
x330wanSpecific	1.3.6.1.4.1.6889.2.1.6.1.1
intWanPortTable	1.3.6.1.4.1.6889.2.1.6.1.1.1		not-accessible	Internal Wan Port configuration table. Each entry in the table specifies the configuration of an internal port, connecting the WAN blade to the host switch.
intWanPortEntry	1.3.6.1.4.1.6889.2.1.6.1.1.1.1		not-accessible	Table of port configuration entries.
INT intWanGroupID	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.1	INTEGER	read-only	The Id of the group in which the port to be configured resides.
INT intWanPortID	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.2	INTEGER	read-only	The Id of the port to be configured.
INT intWanPortSpeed	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.3	INTEGER	read-write	This parameter defines the port speed: ethernet(1) and fastEthernet(2).
INT intWanPortMode	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.4	INTEGER	read-write	The flow control mode of the port when operated in full duplex: halfDuplex(1) - Half duplex connection, standard mode for segment fullDuplexNoPause(2) - Full duplex connection without exchanging flow control packets fullDuplexProprietaryFC(3) - Full duplex connection with AVAYA's proprietary flow control frames exchanged fullDuplexISL(4) - Full duplex connection with ISL proprietary protocol control words for VLAN & priority exchanged, ISL = Inter-Switch-Link fullDuplexFlowControlISL(5) - Full duplex connection with both ISL proprietary protocol control words and flow control frames exchanged fullDuplexAsymTxPause(6) - Full duplex connection with STD 802.3x flow control frames sent from this port, but flow control packets received on it are not processed fullDuplexSymPause(7) - Full duplex connection with STD 802.3x flow control frames exchanged fullDuplexAsymRxPause(8) - Full duplex connection with no flow control frames sent from this port, but STD 802.3x flow control 0frames received on it are processed. For Giga ports, when auto-negotiation is enabled, the flow control mode is set internally according to auto-negotiation resolution; and access to this item is read-only.
INT intWanPortAutoNegotiation	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.5	INTEGER	read-write	This object define if the Auto Sense /Auto Negotiation process is enable(1) or disable (2) for modules that don't support the Auto Snese mode please define the notSupported option..
INT intWanPortVLANMode	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.6	INTEGER	read-write	This item defines the VLAN operation mode of the port: perPortOnly(1) - indicates that all received packets are mapped to the VLAN, defined on the port, and packets are transmitted in untagged format; dot1QTagging(2) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging; plusTagging(3) - indicates that all packets recieved and transmitted on that port are tagged according to Lannet_s PlusTagging scheme. This mode is used when inter-VLAN bridging should be supported; islTagging(4) - indicates that all packets recieved and transmitted on that port are tagged according to the proprietary ISL mode of Lannet; dot1QTaggingButPVID(5) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging, exluding packets that belong to the port_s VLAN,which are transmitted untagged.
INT intWanPortVLANBindingMode	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.7	INTEGER	read-write	VLAN binding mode assigned to this port. static - this port supports only the egress VLAN list as configured manually in its corresponding dot1qVlanStaticEgressPort. This is the default VLAN Binding mode. bindToReceive - this port supports the whole range of 3K VLANs from VLAN ID 1 to 3071. bindToAll - this port supports the egress VLAN IDs for which dot1qVlanStaticTable rows exist. GVRP - this port supports the egress VLAN IDs configured manually in its corresponding dot1qVlanStaticEgressPort as well as VLAN IDs requested by the GVRP link partner.
OCT intWanPortVlanList	1.3.6.1.4.1.6889.2.1.6.1.1.1.1.8	OCTET STRING	read-write	An 4096-bit-long bitmask of all vlans supported on a port. For example: A 1 bit in the 10th place means that vlan 10 is supported.
ds0BundleMemmbersTable	1.3.6.1.4.1.6889.2.1.6.1.1.2		not-accessible	This table is used to quickly assign members to a ds0Bunbdle Its effect is similar as using the ifStack table, only it does it in one go.
ds0BundleMemmbersEntry	1.3.6.1.4.1.6889.2.1.6.1.1.2.1		not-accessible	An entry in yhr ds0BundleMembers table
OCT ds0BundleMemmbersList	1.3.6.1.4.1.6889.2.1.6.1.1.2.1.1	OCTET STRING	read-write	A bit mask of timeslots that are part of the channel group identified by ds0BundleIndex. First (leftmost) bit stands for timeslot 0.
INT ds0BundleSpeedFactor	1.3.6.1.4.1.6889.2.1.6.1.1.2.1.2	INTEGER	read-write	The speed factor for this ds0bundle. This can either be 56k or 64k.
ifs	1.3.6.1.4.1.6889.2.1.6.2
ds1objs	1.3.6.1.4.1.6889.2.1.6.2.1
INT ds1DeviceMode	1.3.6.1.4.1.6889.2.1.6.2.1.1	INTEGER	read-write	The configured device mode. Either all DS1s on the device are e1, t1 or j1. To activate a new selection, perform 'copy running-config startup-config' and reset the device.
INT ds1CurrentDeviceMode	1.3.6.1.4.1.6889.2.1.6.2.1.2	INTEGER	read-only	The current device mode
ifTablePrivateExtensions	1.3.6.1.4.1.6889.2.1.6.2.2
ifTableXtndTable	1.3.6.1.4.1.6889.2.1.6.2.2.1		not-accessible	The ifTableXtndTable table.
ifTableXtndEntry	1.3.6.1.4.1.6889.2.1.6.2.2.1.1		not-accessible	This table is an extension of the itTable. It contains a row per every row of the ifTable. It is used to perform additional configuration, not available through standard mibs. A row will exist in this table for each row in the ifTable, even if specific configuration object has no meaning for the type of interface for which this row is used.
NUM ifTableXtndIndex	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.1	InterfaceIndex	read-only	The index in the ifTable for which this row is providing information.
IP ifTableXtndPeerAddress	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.2	IpAddress	read-only	The IP Address of the peer device on the link identified by this ifIndex. This value is only meaningful for point to point links.
INT ifTableXtndVoIPQueue	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.3	INTEGER	read-write	Turns voip-queueing on or off or turn fair-queuing on.
INT ifTableXtndCableLength	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.4	INTEGER	read-write	Cable length attenuation on this interface.
INT ifTableXtndGain	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.5	INTEGER	read-write	The gain on this interface.
STR ifTableXtndDescription	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.6	DisplayString	read-write	This object is a Read-Write equivalent of ifDescr. It is used to enable users to change the value of ifDescr.
I32 ifTableXtndKeepAlive	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.7	Integer32	read-write	Time, in seconds, between keepalive messages. 0 means keepalive should not be used, or is not supported.
I32 ifTableXtndMtu	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.8	Integer32	read-write	This object is a R/W copy of the ifMtu object from the ifTable. It enables changing of the MTU for interfaces that allow this.
ONO ifTableXtndInvertTxClock	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.9	OnOff	read-write	This object is only applicable for rs232-like synchronuos DTE interefaces. It determines whether the transmit clock is inverted.
ONO ifTableXtndDTELoopback	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.10	OnOff	read-write	This object is only applicable for rs232-like synchronuos DTE interefaces. It determines the status of the DTE loopback.
ONO ifTableXtndIgnoreDCD	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.11	OnOff	read-write	This object is only applicable for rs232-like synchronuos DTE interefaces. This command configures the serial interface to monitor the DSR/CTS signals, instead of DCD signal, as the line up/down indicator.
INT ifTableXtndIdleChars	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.12	INTEGER	read-write	This object is only applicable for rs232-like synchronuos DTE interefaces. This command sets the bit pattern used to indicate an idle line.
I32 ifTableXtndBandwidth	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.13	Integer32	read-write	This object is used to determine the bandwidth of the interface, in Kbps, for interfaces that support it. This information is informational, and does not affect the actual transmission rate.
INT ifTableXtndEncapsulation	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.14	INTEGER	read-write	Applicable only to layer 1 interfaces. The type of the layer 2 interface on top of this Interface. ppp - The Layer 2 interface is PPP frameRelay - The Layer 2 interface is IETF Frame Relay. pppoe - PPPoE-client mode for Ethernet interfaces arpa - non-PPPoE client mode for Ethernet interfaces frameRelayNonIetf - The Layer 2 interface is Frame Relay compliant with Cisco frame relay but not compliant to IETF. interactive - External Modem enabled (for Console & USB-modem interfaces). terminal - External modem disabled (for Console interface)
INT ifTableXtndOperStatus	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.15	INTEGER	read-only	An extension to ifOperStatus, for showing faults and partial faliures, including aggregation of upper layer faults (up to but not including L3). The following Pseudo code describes how the MIB value is calculated for different interfaces: if (AdminStatus is down) { XtndOperStatus= adminDown } else if (OperStatus is testing) { XtndOperStatus = testing } else if (This is a backup interface and its currently in dormant state) { XtndOperStatus= dormantDown } else if (OperStatus = down) { XtndOperStatus = faultDown } else switch interface type { case E1/T1: if (XtndOperStatus of any Channel Group over this I/F is (faultDown or partialDownFault)){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case USP or Channel Group: if (XtndOperStatus of FR or PPP I/F over this I/F is (faultDown or partialDownFault)){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case FastEthernet or loopback: if (XtndKeepAliveStatus is Down) { XtndOperStatus = keepAliveDown } else XtndOperStatus = up break; case PPP or FabricFastEthernet: XtndOperStatus = up break; case Frame Relay: if (XtndOperStatus of any Sub FR over this I/F is (faultDown or partialDownFault)) { XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case Frame Relay Sub I/F: if (at least one DLCI is up, and at least one is down){ XtndOperStatus = partialDownFault } else XtndOperStatus = up break; case Modem: If (modem is undetected) {XtndOperStatus = modemUndetected} elseif (modem is ready to accept calls){XtndOperStatus = modemReady) elseif (a dialer is dialing the modem) {XtndOperStatus = modemDialing} elseif (modem is connected - incoming call) {XtndOperStatus = modemConnectedDialin} elseif (modem is connected - outgoing call) {XtndOperStatus = modemConnectedDialout} }
INT ifTableXtndBackupCapabilities	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.16	INTEGER	read-only	Determines what roles an interface can play in a backup relation. This should be filled per interface, according to its capabilities. primaryAndBackup - the interface can be play both the primary and the backup roles. primaryOnly - the interface can only play the primary role. backupOnly - the interface can only play the backup role. notSupported - the interface can play no role in a backup relation.
NUM ifTableXtndBackupIf	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.17	InterfaceIndex	read-write	The ifIndex of the backup interface for this primary interface. 0 if no backup is defined. The agent will not permit setting this value, if: The intreface is not capable of the primary role, OR The supplied backup index does not point to an interface capable of the backup role, which is not currently in a backup role.
INT ifTableXtndBackupEnableDelay	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.18	INTEGER	read-write	The delay (in Secs) that a primary interface must be inactive before its backup interface is activated. Configurable on the primary interface only.
INT ifTableXtndBackupDisableDelay	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.19	INTEGER	read-write	The delay (in Secs) between the primary coming back to life and its activation and de-activation of its backup interface. The value '-1' means that the primary is never re-activated and the backup is never de-activated. Configurable on the primary interface only.
NUM ifTableXtndPrimaryIf	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.20	InterfaceIndex	read-only	On a backup interface, this will point to the primary interface. '0' means no primary interface.
I32 ifTableXtndCarrierDelay	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.21	Integer32	read-write	This command sets the carrier delay on a serial interface in seconds. If a link goes down and comes back up before the carrier delay timer expires, the down state is effectively filtered, and the switch is not aware that a link-down event occurred.
I32 ifTableXtndDtrRestartDelay	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.22	Integer32	read-write	Determines the period in seconds for deactivating DTR signal when the serial line is inactive.
I32 ifTableXtndDtrPulseTime	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.23	Integer32	read-write	Determines the interval in milliseconds DTR signal is held inactive when the serial line is inactive.
I32 ifTableXtndLoadInterval	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.24	Integer32	read-write	Determines interval (in secs) for exponential averages calculations for an interface. Must be a multiple of 30.
G32 ifTableXtndInputRate	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.25	Gauge32	read-only	Expoential Average of the Number of bits received per second calculated for the interval specified in ifTableXtndLoadInterval. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= (bitsLast - bitCurrent)/5 where bitCurrent = number of bits received, sampled every 5 seconds. new_ifTableXtndInputRate = (old_ifTableXtndInputRate - RateSample) *exp( -5/LoadInterval) + RateSample
G32 ifTableXtndOutputRate	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.26	Gauge32	read-only	Expoential Average of the Number of bits sent per second calculated for the interval specified in ifTableXtndLoadInterval. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= (bitsLast - bitCurrent)/5 where bitCurrent = number of bits sent, sampled every 5 seconds. new_ifTableXtndOutputRate = (old_ifTableXtndOutputRate - RateSample) *exp( -5/LoadInterval) + RateSample
G32 ifTableXtndInputLoad	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.27	Gauge32	read-only	Expoential Average of the Input Load calculated for the interval specified in ifTableXtndLoadInterval. Load is expressed a a number in the range 1 to 255. 255 = 100% utilization (input bits per second equal the interface speed). 1 = 0% utilization. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= int((bitsLast - bitCurrent)/(5ifSpeed))254 +1 where bitCurrent = number of bits received, sampled every 5 seconds. new_ifTableXtndInputLoad = (old_ifTableXtndInputLoad - RateSample) *exp( -5/LoadInterval) + RateSample
G32 ifTableXtndOutputLoad	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.28	Gauge32	read-only	Expoential Average of the Output Load calculated for the interval specified in ifTableXtndLoadInterval. Load is expressed a a number in the range 1 to 255. 255 = 100% utilization (input bits per second equal the interface speed). 1 = 0% utilization. The exponentail average smooths peaks while correctly showing current trends. Calculated as follows: RateSample= int((bitsLast - bitCurrent)/(5ifSpeed))254 +1 where bitCurrent = number of bits sent, sampled every 5 seconds. new_ifTableXtndOutputLoad = (old_ifTableXtndOutputLoad - RateSample) *exp( -5/LoadInterval) + RateSample
G32 ifTableXtndReliability	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.29	Gauge32	read-only	Expoential Average of the Reliability of an interface calculated for the interval specified in ifTableXtndLoadInterval. Reliability is expressed a a number in the range 1 to 255. 255 = Fully Reliable interface. 1 = Interface is extremly un reliable. The exponentail average smooths peaks while correctly showing current trends. RateSample is calculated every 5 seconds as follows: If (OperStatus is down and Admin status is Up) RateSample =1 else RateSample = 255 new_ifTableXtndReliability = (old_ifTableXtndReliability - RateSample) *exp( -5/LoadInterval) + RateSample
I32 ifTableXtndTrafficShaperRate	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.30	Integer32	read-write	This item controls a traffic shaper on the interface. Its value is the shaping rate in bits per seconds. When zero, the shaper is disabled
I32 ifTableXtndCacBBL	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.31	Integer32	read-write	Dynamic CAC Bearer Bandwidth Limit in kilo-bits-per-seconds. This item equals -1 when dynamic CAC is not configured.
I32 ifTableXtndCacPriority	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.32	Integer32	read-write	If more than one interface with configured BBL is up, the gateway reports the BBL of the interface with the highest activation priority value. If N active interfaces shares the same highest CAC activation priority. The gateway's RBBL is equals N multiple by the lowest BBL value in this interface group. If the activation priority is unspecified, it receives the default value (5). .
INT ifTableXtndCacifStatus	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.33	INTEGER	read-only	Dynamic CAC status of the interface.
OCT ifTableXtndCommonApplifStatus	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.34	OCTET STRING	read-only	Supported Application on this Interface. If 0 value - Not supported else supported. Bit 0 - Unknown Application. Bit 1 - Support of Next Hop Interface in Policy Based Routing Application.
INT ifTableXtndIpSecDfBit	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.35	INTEGER	read-write	This item controls whether the DF (don't fragment) bit of incoming packets is copied to the external IPSec header
I32 ifTableXtndMinPmtu	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.36	Integer32	read-write	Set the minimal PMTU for IPSec tunnels.
STR ifTableXtndConfString	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.37	DisplayString	read-write	An additional configuration string for the interface. init-string - for modem interfaces
INT ifTableXtndPppIpcpDnsOptionRequest	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.38	INTEGER	read-write	PPP-IPCP DNS option request. Configuration whether during the PPP-IPCP negotiation the DNS option will be requested. Default: Disable. The DNS information gathered will be used by the DNS resolver to resolve hostnames. 1 - enable 2 - disable 255 - notSupported, this Mib item related only to PPP-IPCP interfaces. Other interfaces which are not PPP-IPCP, will return this value.
U32 ifTableXtndKeepaliveTrackId	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.39	Unsigned32	read-write	Bind the status of this interface to an object-tracker by specifying the ID of the object-tracker (avstrTrackerId in AVAYA-SAA-TRACK-MIB). A value of 0 means that interface is not bound to any object-tracker. A value of 0xffffffff is notSupported feature for the relevant interface.
ONO ifTableXtndFrTrafficShaping	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.40	OnOff	read-write	This object determines / indicates whether Frame-Relay Traffic-Shaping is enabled (on) or disabled (off) for this interface. This object can be set only for interfaces, but not for sub-interfaces. This object is applicable only for interfaces which ifTableXtndEncapsulation is Frame-Relay (i.e. frameRelay, frameRelayNonIetf).
INT ifTableXtndType	1.3.6.1.4.1.6889.2.1.6.2.2.1.1.41	INTEGER	read-write	Extended type is, currently, required for modem interfaces
xtndKeepAliveTable	1.3.6.1.4.1.6889.2.1.6.2.2.2		not-accessible	The Extended Keepalive Parameters Table.
xtndKeepAliveEntry	1.3.6.1.4.1.6889.2.1.6.2.2.2.1		not-accessible	This table contains the extended keepalive parameters. The Table is per interface. Although for the first phase it will be relevant for WAN Fast Ethernet Port. But may be available in the future for interface. The keepalive on specific interface may bring it to line protocol down according the results. The main idea is to check certain IP that if not responding then the link/route may be down and therefore the interface is bring to line protocol down. In this case there still be sent extended keepalive packets in order to check whether the line protocol is up.
NUM xtndKeepAliveifIndex	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.1	InterfaceIndex	read-only	The index in the ifTable for which this row is providing information.
INT xtndKeepAliveMethod	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.2	INTEGER	read-write	The type of the extended keepalive. icmpPing(1),tcpConnect(2),httpGet(3) Default is IcmpPing.
I32 xtndKeepAliveTimeout	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.3	Integer32	read-write	Timeout in seconds to wait for a reply. Applicable to non-TCP tests such as ICMP Echo, UDP. Default 1second.
I32 xtndKeepAliveUpRetries	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.4	Integer32	read-write	The number of successful extended keepalive necessary to determine that the next hop router is operational.
I32 xtndKeepAliveDownRetries	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.5	Integer32	read-write	The number of unsuccessful extedned keepalive necessary to determine that the next hop router is not operational.
I32 xtndKeepAliveInterval	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.6	Integer32	read-write	The extended keepliave interval in seconds
IP xtndKeepAliveSrcIPAddr	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.7	IpAddress	read-write	The Source IP address to use. Default is the primary IP address of the interface. Setting the address 0.0.0.0 will reset the xtndKeepAliveSrcIPAddr to the primary IP interface address
IP xtndKeepAliveIPAddr	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.8	IpAddress	read-write	The IP address that it status shall be checked.
PHY xtndKeepAliveNextHopMAC	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.9	PhysAddress	read-write	The next Hop MAC, Valid for Ethernet Interfaces.
INT xtndKeepAliveStatus	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.10	INTEGER	read-only	The Status of the extended KeepAlive. I.e. whether the current extended KeepAlive succeeded. 1 - up 2 - down 3 - disable
INT xtndKeepAliveMode	1.3.6.1.4.1.6889.2.1.6.2.2.2.1.11	INTEGER	read-write	Extended KeepAlive Mode. 1 - enable 2 - disable
frameRelay	1.3.6.1.4.1.6889.2.1.6.2.4
frDlcmiXtndTable	1.3.6.1.4.1.6889.2.1.6.2.4.1		not-accessible	This table extends the standard frDlcmiTable, which models RFR I/Fs. Entries are created by the agent for Frame Relay I/Fs, and are deleted when those entries are deleted.
frDlcmiXtndEntry	1.3.6.1.4.1.6889.2.1.6.2.4.1.1		not-accessible	Each Entry corresponds to a Frame Relay Interface. Entries are created & deleted automatically by the agent, when ifTableXtndEncapsulation of the underlying Layer 1 Interface is changed.
NUM frDlcmiXtndIndex	1.3.6.1.4.1.6889.2.1.6.2.4.1.1.1	InterfaceIndex	read-only	The ifIndex assigned to The Frame Relay interface is calculated by a known formula, which is agent-type specific.
ONO frDlcmiXtndLMIAutoSense	1.3.6.1.4.1.6889.2.1.6.2.4.1.1.2	OnOff	read-write	Enable/disable automatic detection (By sending all supported keepalives) of the Local Management Interface (LMI) on the Frame Relay Interface.
frStaticCircuitTable	1.3.6.1.4.1.6889.2.1.6.2.4.2		not-accessible	This table is used to create/associate/delete A Virtual Channel (DLCI) with a specific Frame Relay Sub Interface. When an entry is created in this table: If the DLCI is the same as that of a dynamic frCircuit leraned on the Frame Relay Interface layered bellow the Sub Interface specified by the entry then: - The DLCI's status is changed to Static Else - A new static DLCI is created. In both cases, the static DLCI is assigned to the specified Frame Relay Sub Interface.
frStaticCircuitEntry	1.3.6.1.4.1.6889.2.1.6.2.4.2.1		not-accessible	An Entry represent a Virtual Channel available on a specific Frame Relay Interface.
NUM frStaticCircuitSubIfIndex	1.3.6.1.4.1.6889.2.1.6.2.4.2.1.1	InterfaceIndex	read-only	Description.
DLC frStaticCircuitDLCI	1.3.6.1.4.1.6889.2.1.6.2.4.2.1.2	DLCI	read-only	The virtual channel identifier.
INT frStaticCircuitDLCIrole	1.3.6.1.4.1.6889.2.1.6.2.4.2.1.3	INTEGER	read-only	The role of the VC in this interface. primary - the state of this VC determines the operStatus of the interface. For point to point interfaces, the agent will not permit more than one primary to exist. A sub interface for which no primary is defined will be down. priority6to7 - This VC handles high priority (forwarding class 6 to 7)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority4to5 - This VC handles Medium priority (forwarding class 4 to 5)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority2to3 - This VC handles Normal priority (forwarding class 2 to 3)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured. priority0to1 - This VC handles Low priority (forwarding class 0 to 1)traffic. If this VC does not exists, the sub interface will send all traffic through the primary VC (no priority-dlci-group) In point to point interfaces, only one such VC can be configured.
ROW frStaticCircuitStatus	1.3.6.1.4.1.6889.2.1.6.2.4.2.1.4	RowStatus	read-write	Used to create/associate/delete a DLCI to a Sub FrameRelay Interface. Note that the frStaticCircuitDLCIrole defines limitations on creation and deletion of DLCIs. The notInService state will not be implemented.
STR frStaticCircuitMapClass	1.3.6.1.4.1.6889.2.1.6.2.4.2.1.5	DisplayString	read-write	A pointer to a 'map-class frame-relay' entry applicable for this row. A 'map-class frame-relay' is an entry in the frMapClassTable. The value of this object must be identical to the value of the desired entry's frMapClassName in the frMapClassTable. NOTES: 1. This object can only a point to an existing entry. Trying to set this object to a value that does not pertain to an existing entry in frMapClassTable shall fail. 2. An entry in the frMapClassTable can be deleted only when it is not pointed to by any entry in this table (frStaticCircuitTable). 3. The map-class is activated only when the containing interface has Frame-Relay Traffic-Shaping enables. See description of ifTableXtndFrTrafficShaping for details about FRTS. 4. The frMapClassTable contains a persistent, non-deletable default entry, by the name 'default'.
frSubIfTable	1.3.6.1.4.1.6889.2.1.6.2.4.3		not-accessible	A Frame Relay Sub Interface is the Layer 2 interface to which Layer 3 (IP) Interfaces are assigned. This Logical Interface is hinted at but not modeled by the RFC2115 Frame-Relay DTE MIB. This table manages the creation/deletion of Frame Relay Sub I/Fs. Entries are created by the Creator of a sub-I/F.
frSubIfEntry	1.3.6.1.4.1.6889.2.1.6.2.4.3.1		not-accessible	An Entry in this table defines a Frame Relay Sub Interface of a specific type, defined over a specific Frame Relay Interface. Note that although the MIB model allow for two SubFR I/Fs to have the same ifIndex and have different Frame Relay I/Fs or FR types, the agent will allow only a single suc interface - the first one defined.
NUM frSubIfDlcmiIndex	1.3.6.1.4.1.6889.2.1.6.2.4.3.1.1	InterfaceIndex	read-only	The ifIndex of the Frame Relay Interface this Sub Interface is created over.
NUM frSubIfSubIndex	1.3.6.1.4.1.6889.2.1.6.2.4.3.1.2	InterfaceIndex	read-only	The ifIndex of the Sub Interface. Note that the Mnagement station must select a sub interface number in the permissible range (which is agent-type dependent.) Agent Type ifIndex Range ========== ============= X330WAN 8000-8999
INT frSubIfType	1.3.6.1.4.1.6889.2.1.6.2.4.3.1.3	INTEGER	read-only	The Type of the Sub Interface. point2point - A Point to Point Interface. Point2multiPoint - Point to multi-point interface.
ROW frSubIfStatus	1.3.6.1.4.1.6889.2.1.6.2.4.3.1.4	RowStatus	read-create	Creation/Deletion of a Frame Relay Sub Interface over a Frame Relay Interface. The Agent will refuse to delete a Sub Interface if there are IP Interfaces associated with it.
frMapClassTable	1.3.6.1.4.1.6889.2.1.6.2.4.4		not-accessible	This table contains the 'map-class frame-relay' entries in the system. A 'map-class frame-relay' entry is a collection of QoS-related parameters that can be attached to a Frame-Relay DLCI. An entry in this table can be attached to a DLCI by setting the value of frStaticCircuitMapClass in frStaticCircuitTable to the value of the frMapClassName of an entry in this table. An entry in this table can be deleted only when it is not pointed to by any entry in frStaticCircuitTable. Trying to delete an entry that does not correspond to that shall fail. This table contains a default entry that can be modified, but cannot be deleted. The value of frMapClassName for that entry is 'default'.
frMapClassEntry	1.3.6.1.4.1.6889.2.1.6.2.4.4.1		not-accessible	An entry in the table, which represents a 'frame-relay map-class' object.
STR frMapClassName	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.1	DisplayString	not-accessible	The name of the map-class, which is also the only index component of this table. NOTE: This object can only contain a lower-case string! Trying to use upper-case characters on creation shall result in a failure.
U32 frMapClassBcOut	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.2	Unsigned32	read-write	The output Commited Burst size, in bits. Valid range is 300-39999999.
U32 frMapClassBeOut	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.3	Unsigned32	read-write	The output Excess Burst size, in bits. Valid range is 0-39999999.
U32 frMapClassCirOut	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.4	Unsigned32	read-write	The Committed Information Rate, in bits per second. Valid range is 1000-39999999.
I32 frMapClassFrf12Frag	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.5	Integer32	read-write	Disable or enable FRF.12 fragmentation, and determine fragment size: The reserved value zero means FRF.12 fragmentation is disabled. A value larger then zero means FRF.12 fragmentation is enabled, and the fragment size in bytes is equal to the value of this object.
ROW frMapClassRowStatus	1.3.6.1.4.1.6889.2.1.6.2.4.4.1.6	RowStatus	read-write	This object is used to create a new row or destroy an existing row in the manner described in the definition of the RowStatus textual convention. The value of this object has no effect on whether other objects in this conceptual row can be modified. Use createAndGo (not createAndWait) to create this row.
wanDialer	1.3.6.1.4.1.6889.2.1.6.2.5
wanDialerTable	1.3.6.1.4.1.6889.2.1.6.2.5.1		not-accessible	This table is used for configuring Dialer interfaces.
wanDialerEntry	1.3.6.1.4.1.6889.2.1.6.2.5.1.1		not-accessible
I32 wanDialerModemIf	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.1	Integer32	read-write	The ifIndex of the modem interface
INT wanDialerState	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.2	INTEGER	read-only	The current state of the dialer finit-state-machine
I32 wanDialerPersistentDelay	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.3	Integer32	read-write	The number of seconds between persistent dial attempts (zero= no persistent dialing)
I32 wanDialerPersistentMaxAttempts	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.4	Integer32	read-write	The interval between persistent (non-DDR) dial attempts. Zero means no persistent dialing
I32 wanDialerPersistentReenable	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.5	Integer32	read-write	The time (in seconds) the dialer is disabled after it exhausts its consecutive dial attempts quota (wanDialerPersistentMaxAttempts). Zero means that the dialer is disabled until the dialing the current dial trigger disappears.
INT wanDialerOrder	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.6	INTEGER	read-write	The dial strings list usage order where: sequential(1) : The dialer starts from the beginning of the list when there is a new reason to dial (dial trigger. roundRobin(2): The dialer use the dialing string that is right after the last one dialed. lastSuccessful(3) : If the previous dial attempt was successful, the dialer starts with its dial strings.
STR wanDialerString1	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.7	DisplayString	read-write	The 1st dial string in the list(NULL=unconfigured)
STR wanDialerString2	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.8	DisplayString	read-write	The 2nd dial string in the list(NULL=unconfigured)
STR wanDialerString3	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.9	DisplayString	read-write	The 3rd dial string in the list(NULL=unconfigured)
STR wanDialerString4	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.10	DisplayString	read-write	The 4th dial string in the list(NULL=unconfigured)
STR wanDialerString5	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.11	DisplayString	read-write	The 5th dial string in the list(NULL=unconfigured)
STR wanDialerLastDialed	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.12	DisplayString	read-only	The last used display string
I32 wanDialerWaitForIpcp	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.13	Integer32	read-write	The maximum time (in seconds) the dialer waits from dialing until PPP/IPCP is up.
I32 wanDialerPersistentInitial	1.3.6.1.4.1.6889.2.1.6.2.5.1.1.14	Integer32	read-write	The minimum delay (in seconds) from boot to persitent dialing.
avayaEISWanTraps	1.3.6.1.4.1.6889.2.1.6.4
avayaEISWanGroups	1.3.6.1.4.1.6889.2.1.6.5
hostModuleGroup	1.3.6.1.4.1.6889.2.1.6.5.1			Mib objects for controlling the fabric port, connecting a LAN switch to its WAN router.
wanRouterBladeGroup	1.3.6.1.4.1.6889.2.1.6.5.2			Mib object that belong to the WAN router.
avayaEISWanCompliances	1.3.6.1.4.1.6889.2.1.6.7
hostModuleCompliance	1.3.6.1.4.1.6889.2.1.6.7.1			The host module should only support the host module group.
wanRouterBladeCompliance	1.3.6.1.4.1.6889.2.1.6.7.2			The wan router blade should support the wan router blade group.

RFC description

Avaya WAN interface management for DS0/DS1/E1 bundling, frame relay, keepalive tracking, and protocol encapsulation configuration.

Start monitoring Avaya WAN access router/gateway (WAN link up/down/traffic-error counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WAN-MIB

What Is WAN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description