Unisphere-Data-POLICY-MIB

All MIBs › Unisphere-Data-POLICY-MIB

Organization: Unisphere Networks, Inc.

Last Updated: 2002-03-28

Category: Juniper Unisphere ERX Routing

Description: Manages Unisphere ERX QoS and traffic policy rules, classification, and enforcement configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Unisphere-Data-POLICY-MIB?

Unisphere-Data-POLICY-MIB is a Unisphere Networks (Juniper ERX) enterprise MIB for managing QoS and traffic policy rules, covering classification, rate limiting, and enforcement configuration on ERX edge routers. It exposes a policy table with administrative and operational state per policy, along with classifier and rate-limit control lists that define how traffic is matched and shaped. This MIB monitors software/configuration status rather than physical hardware: it lets an operator confirm whether a given traffic policy is administratively enabled and operationally active (usdPolicyAdminState/usdPolicyOperStatus), and surfaces error codes when a policy fails to apply. It depends on the standard IF-MIB for associating policies to interfaces and complements other Unisphere QoS-related MIBs. It is typically deployed on Juniper/Unisphere ERX edge routers enforcing per-subscriber QoS and traffic-shaping policies in broadband aggregation networks, and the Unisphere-Data-POLICY-MIB download is available for administrators to load into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Unisphere-Data-POLICY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper/Unisphere ERX edge router

Monitoring Examples

An admin would walk usdPolicyTable/usdPolicyEntry to check usdPolicyOperStatus against usdPolicyAdminState for a given usdPolicyId, and inspect usdPolicyErrorValue when a policy fails to activate as expected. The usdClassifierControlList and usdRateLimitControlList objects would be reviewed to confirm the correct traffic classification and rate-limiting rules are bound to a policy, useful when troubleshooting a subscriber whose traffic isn't being shaped as configured.

What Can Be Monitored

policy administrative state
policy operational status
policy error codes
classifier control list assignments
rate-limit control list assignments

Imported Objects

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

From Unisphere-Data-MIBs

usDataMibs

MODULE-IDENTITY

How to Use in IPNetwork Monitor

Example using usdPolicyReferenceCount OID:

Select a Juniper/Unisphere ERX edge router (QoS/traffic-policy admin/oper status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type usdPolicyReferenceCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Reflects the number of times this policy has been applied within the chassis. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
usdPolicyMIB	1.3.6.1.4.1.4874.2.2.27			The Policy MIB for the Unisphere Networks Inc. enterprise.
usdPolicyObjects	1.3.6.1.4.1.4874.2.2.27.1
usdClassifierControlList	1.3.6.1.4.1.4874.2.2.27.1.1
I32 usdClassifierControlListNextIndex	1.3.6.1.4.1.4874.2.2.27.1.1.1	Integer32	read-only	This scalar object returns the index of the next available row in the usdClassifierControlListTable. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended.
usdClassifierControlListTable	1.3.6.1.4.1.4874.2.2.27.1.1.2		not-accessible	This table contains entries for elements of classifier control lists. The details pertinent to each CLACL are found in the usdClassifierControlDefTable.
usdClassifierControlListEntry	1.3.6.1.4.1.4874.2.2.27.1.1.2.1		not-accessible	Each entry describes the characteristics of an IP access list element.
I32 usdClassifierControlListId	1.3.6.1.4.1.4874.2.2.27.1.1.2.1.1	Integer32	not-accessible	The number of the classifier control list to which this entry belongs.
ROW usdClassifierControlListRowStatus	1.3.6.1.4.1.4874.2.2.27.1.1.2.1.3	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. Modes supported are create-and-go and destroy. To create an entry in this table, the following entry objects MUST be explicitly configured: usdClassifierControlListRowStatus usdClassifierControlListElemId
STR usdClassifierControlListName	1.3.6.1.4.1.4874.2.2.27.1.1.2.1.4	DisplayString	read-create	The name of the CLACL being defined.
C32 usdClassifierControlListReferenceCount	1.3.6.1.4.1.4874.2.2.27.1.1.2.1.5	Counter32	read-only	Number of times this CLACL is referenced by policies.
I32 usdClassifierControlListNextElementIndex	1.3.6.1.4.1.4874.2.2.27.1.1.2.1.6	Integer32	read-only	Each get of this object will return a unique index which may be used to create classifier control list elements. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended.
usdClassifierControlListElementTable	1.3.6.1.4.1.4874.2.2.27.1.1.4		not-accessible	This table contains entries for elements of classifier control lists. Entries belonging to the same control list are ordered, and comparisons to those entries are performed in that order until a match is detected. If no match is found, the default action is to 'deny'.
usdClassifierControlListElementEntry	1.3.6.1.4.1.4874.2.2.27.1.1.4.1		not-accessible	Each entry describes the characteristics of an IP access list element.
I32 usdClassifierControlListElemId	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.1	Integer32	not-accessible	The relative position of this entry within its classifier control list. Classifier control list entries are searched in this sequence (low to high values) until a match is found.
ROW usdClassifierControlListElemRowStatus	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.2	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. This table provides a partial implementation for rowStatus. Rows may be created using createAndGo and createAndWait. Once a row has been made active the row status may not be changed.
T/F usdClassifierControlListNotSrc	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.3	TruthValue	read-create	Invert the meaning of the source IP address and mask objects. For example 'not 10.10.0.90/255.255.255.255 (host address)' would result in all source addresses except for host 10.19.9.90 being matched.
IP usdClassifierControlListSrc	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.4	IpAddress	read-create	A source IP address. A subject IP address is first masked with the value of usdClassifierControlListSrcMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any source IP address.
IP usdClassifierControlListSrcMask	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.5	IpAddress	read-create	The IP address mask to be applied to a subject source IP address before comparing it to usdClassifierControlListSrc. Ones in the mask identify which bits in the subject IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
T/F usdClassifierControlListNotDst	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.6	TruthValue	read-create	Invert the meaning of the destination IP address and mask objects. For example, 'not 10.10.0.90/255.255.255.255 (host address)' would result in all source addresses except for host 10.19.9.90 being matched.
IP usdClassifierControlListDst	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.7	IpAddress	read-create	A destination IP address. A subject IP address is first masked with the value of usdClassifierControlListDstMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any destination IP address.
IP usdClassifierControlListDstMask	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.8	IpAddress	read-create	The IP address mask to be applied to a subject destination IP address before comparing it to usdClassifierControlListDst. Ones in the mask identify which bits in the IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
T/F usdClassifierControlListNotProtocol	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.9	TruthValue	read-create	Invert the meaning of the protocol object. For example, 'not TCP' matches any protocol except for TCP.
I32 usdClassifierControlListProtocol	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.10	Integer32	read-create	An IP Protocol value. Nonzero values match a specific IP Protocol value (e.g. 6 for TCP) carried in an IP packet; a value of zero acts as a wildcard, matching any IP Protocol.
I32 usdClassifierControlListTosByte	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.11	Integer32	read-create	The IP TOS byte value to match.
I32 usdClassifierControlListMask	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.12	Integer32	read-create	The mask to use for TOS byte checks. Allowed values are 0, 224, 252, 255.
USD usdClassifierControlListSrcOperator	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.13	UsdClaclPortOperator	read-create	Operator for use in comparing source ports.
I32 usdClassifierControlListSrcFromPort	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.14	Integer32	read-create	Source UDP or TCP 'from' port number.
I32 usdClassifierControlListSrcToPort	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.15	Integer32	read-create	Source UDP or TCP 'to' port number.
USD usdClassifierControlListDestOperator	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.16	UsdClaclPortOperator	read-create	Operator for use in comparing Destination ports.
I32 usdClassifierControlListDestFromPort	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.17	Integer32	read-create	Destination UDP or TCP 'from' port number.
I32 usdClassifierControlListDestToPort	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.18	Integer32	read-create	Destination UDP or TCP 'to' port number.
I32 usdClassifierControlListICMPType	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.19	Integer32	read-create	Optional ICMP message type for classification.
I32 usdClassifierControlListICMPCode	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.20	Integer32	read-create	Optional ICMP message code for classification.
I32 usdClassifierControlListIGMPType	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.21	Integer32	read-create	Optional IGMP message type for classification.
I32 usdClassifierControlListTcpFlagsValue	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.22	Integer32	read-create	Optional TCP flags value for classification.
I32 usdClassifierControlListTcpFlagsMask	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.23	Integer32	read-create	Optional TCP flags mask for classification. TCP flag bits not specified in the mask are don't care bits.
I32 usdClassifierControlListIpFlagsValue	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.24	Integer32	read-create	Optional IP flags value for classification.
I32 usdClassifierControlListIpFlagsMask	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.25	Integer32	read-create	Optional IP flags mask for classification. IP flag bits not specified in the mask are don't care bits
USD usdClassifierControlListIpFragValue	1.3.6.1.4.1.4874.2.2.27.1.1.4.1.26	UsdPolicyIpFragValue	read-create	Optional IP flags mask for classification. IP flag bits not specified in the mask are don't care bits
usdRateLimitControlList	1.3.6.1.4.1.4874.2.2.27.1.2
I32 usdRateLimitProfileNextIndex	1.3.6.1.4.1.4874.2.2.27.1.2.1	Integer32	read-only	This scalar object returns the index of the next available row in the usdRateLimitProfileTable. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended.
usdRateLimitProfileTable	1.3.6.1.4.1.4874.2.2.27.1.2.2		not-accessible	This table contains entries for elements of Rate Limit Profile (RLP) definitions.
usdRateLimitProfileEntry	1.3.6.1.4.1.4874.2.2.27.1.2.2.1		not-accessible	Each entry describes the characteristics of a rate limit profile element.
I32 usdRateLimitProfileId	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.1	Integer32	not-accessible	The ID number of the rate limit profile (RLP) entry which is defined by this row.
ROW usdRateLimitProfileRowStatus	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.2	RowStatus	read-write	Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: usdRateLimitProfileName
STR usdRateLimitProfileName	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.3	DisplayString	read-write	Specifies the name of the rate limit profile defined by this row.
C32 usdRateLimitReferenceCount	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.4	Counter32	read-only	This object reflects the number of times a rate limit profile object is referenced by policies.
U32 usdRateLimitCommittedBps	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.5	Unsigned32	read-write	The committed access rate in bits per second.
U32 usdRateLimitCommittedBurst	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.6	Unsigned32	read-write	The committed access rate burst value in bytes.
U32 usdRateLimitExceedBps	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.7	Unsigned32	read-write	The peak access rate in bits per second. To be configured only if rate limit profile type is two-rate.
U32 usdRateLimitExceedBurst	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.8	Unsigned32	read-write	The peak access rate burst value in bytes. To be configured only if rate limit profile type is two-rate.
INT usdRateLimitCommittedAction	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.9	INTEGER	read-write	Action to be taken when the access rate is within the bounds of the committed access rate.
INT usdRateLimitConformedAction	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.10	INTEGER	read-write	Action to be taken when the access rate exceeds the bounds of the committed access rate.
INT usdRateLimitExceededAction	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.11	INTEGER	read-write	Action to be taken when the access rate exceeds the bounds of the peak access rate.
I32 usdRateLimitCommittedMarkVal	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.12	Integer32	read-write	New IP precedence to be used when the usdRateLimitCommittedAction mark action is applied.
I32 usdRateLimitConformedMarkVal	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.13	Integer32	read-write	New IP prececence to be used when the usdRateLimitExceedCommittedAction mark action is applied.
I32 usdRateLimitExceededMarkVal	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.14	Integer32	read-write	New IP precedence to be used when the usdRateLimitExceedPeakAction mark action is applied.
U32 usdRateLimitMask	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.15	Unsigned32	read-write	Mask to be applied when executing a mark action.
USD usdRateLimitProfileType	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.16	UsdRateLimitProfileType	read-write	The rate limit profile type (i.e. one-rate or two-rate). Defaults to two-rate, if not specified.
U32 usdRateLimitExcessBurst	1.3.6.1.4.1.4874.2.2.27.1.2.2.1.17	Unsigned32	read-write	The excess committed access rate burst value in bytes. To be configured only if rate limit profile type is one-rate.
usdPolicy	1.3.6.1.4.1.4874.2.2.27.1.3
I32 usdPolicyNextIndex	1.3.6.1.4.1.4874.2.2.27.1.3.1	Integer32	read-only	This scalar object returns the index of the next available row in the usdPolicyTable. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended.
usdPolicyTable	1.3.6.1.4.1.4874.2.2.27.1.3.2		not-accessible	This table contains entries which represent the non-repetive fields of a policy definition.
usdPolicyEntry	1.3.6.1.4.1.4874.2.2.27.1.3.2.1		not-accessible	Each entry contains the non-repetitive fields of a policy definition.
I32 usdPolicyId	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.1	Integer32	not-accessible	The number of the policy table entry which is defined by this row.
ROW usdPolicyRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy * LIMITED ACCESS LIST CONFIGURATION LEVEL * RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create a policy table entry with the associated policy name. destroy Destroy the specified list and all of its constituent elements. Policy row members may not be modified once the row has been created.
INT usdPolicyAdminState	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.3	INTEGER	read-create	This object is used to control the administrative state of a policy. Enabling a policy will result in the rules which make up a policy being applied to interfaces to which the policy is assigned. Disabling a policy results in the the policy being taken out of service. This object may be modified while the row is active.
INT usdPolicyOperStatus	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.4	INTEGER	read-only	This object is used to retrieve the operational state of a policy. If a policy is disabled, it is not applied to any interfaces within the system. If a policy is invalid, there is a problem with the policy preventing it from being applied to an interface. An error code providing diagnostic information about the problem is found in usdPolicyErrorValue. If a policy is enabled, it has been applied to one or more interfaces within the system.
I32 usdPolicyErrorValue	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.5	Integer32	read-only	An error code providing diagnostic information for invalid policies. The enumeration of this field is TBD. A zero (0) value indicates that there is no error reported.
STR usdPolicyName	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.6	DisplayString	read-create	Specifies the name of the policy defined by this row.
C32 usdPolicyReferenceCountEx	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.7	Counter32	read-only	Reflects the number of times this policy has been applied within the chassis.
I32 usdPolicyRuleNextIndex	1.3.6.1.4.1.4874.2.2.27.1.3.2.1.8	Integer32	read-only	Read only variable which provides the next available PolicyRuleIndex with respect to the policy defined by this row. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended.
usdPolicyRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.3		not-accessible	Each entry within this table defines a rule component of a policy. The entries in this table are created automatically when entries are created in specific rule tables. This table is read only
usdPolicyRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.3.1		not-accessible	Each entry defines a single rule component.
I32 usdPolicyRulePolicyId	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.1	Integer32	not-accessible	The PolicyTable index of the policy which owns this rule.
I32 usdPolicyRulePrec	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.2	Integer32	not-accessible	The precedence of this rule within this group of policy rules.
I32 usdPolicyRuleId	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.3	Integer32	not-accessible	The index of this rule within the set of rules owned by the policy defined by usdPolicyRulePolicyId.
INT usdPolicyRuleType	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.4	INTEGER	read-only	This field specifies the type of rule being defined. The remaining information which makes up this rule is found in the specific rule table defined by usdPolicyRuleType. The specific rule tables are indexed by usdPolicyRulePolicyId.usdPolicyRuleId.
T/F usdPolicySuspend	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.5	TruthValue	read-write	Setting this object to true results in the rule being suspended (taken out of service). Setting this value to false results in the rule being returned to service.
T/F usdPolicyEclipsed	1.3.6.1.4.1.4874.2.2.27.1.3.3.1.6	TruthValue	read-only	This value is true if the policy rule is eclipsed. A policy rule is eclipsed if a conflicting rule with the same classifier control list precedes the rule, and the preceding rule is not suspended. A false value indicates that the rule is not eclipsed.
usdNextHopRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.4		not-accessible	A list of entries which provide next-hop rule data. Rows created in this table result in an entry being created in the policy rule table.
usdNextHopRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.4.1		not-accessible	A next-hop rule entry.
ROW usdNextHopRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.4.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The next-hop IP address is mandatory and must be specified. Modes supported are create-and-go and destroy.
IP usdNextHopIpAddress	1.3.6.1.4.1.4874.2.2.27.1.3.4.1.2	IpAddress	read-create	The IP address to forward all packets to.
I32 usdNextHopClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.4.1.3	Integer32	read-create	The classifier control list ID which completes the NextHop policy rule.
usdFilterRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.5		not-accessible	A list of entries which provide filter rule data. Creation of an entry in this table results in a corresponding entry being created in the policy rule table.
usdFilterRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.5.1		not-accessible	A filter rule entry.
ROW usdFilterRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.5.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. Modes supported are create-and-go and destroy.
I32 usdFilterClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.5.1.2	Integer32	read-create	The classifier control list ID which completes the filter policy rule.
usdNextInterfaceRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.6		not-accessible	A list of entries which provide NextInterface rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table.
usdNextInterfaceRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.6.1		not-accessible	A NextInterface rule entry.
ROW usdNextInterfaceRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.6.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The next-interface parameter is mandatory and must be specified. Modes supported are create-and-go and destroy.
NUM usdNextInterfaceId	1.3.6.1.4.1.4874.2.2.27.1.3.6.1.2	InterfaceIndex	read-create	The interface index to which traffic matching the CLACL ID will be routed.
I32 usdNextInterfaceClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.6.1.3	Integer32	read-create	The classifier control list ID which completes the NextInterface policy rule.
IP usdNextInterfaceNextHop	1.3.6.1.4.1.4874.2.2.27.1.3.6.1.4	IpAddress	read-create	The IP address to forward all packets to.
usdRateLimitRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.7		not-accessible	A list of entries which provide RateLimit rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table.
usdRateLimitRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.7.1		not-accessible	A RateLimit rule entry.
ROW usdRateLimitRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.7.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The rate limit profile ID is mandatory and must be specified. Modes supported are create-and-go and destroy.
I32 usdRateLimitId	1.3.6.1.4.1.4874.2.2.27.1.3.7.1.2	Integer32	read-create	The RLP ID which provides the rate limit data which completes the RateLimit policy rule.
I32 usdRateLimitClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.7.1.3	Integer32	read-create	The classifier control list ID which fills out the RateLimit policy rule.
usdMarkingRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.8		not-accessible	A list of entries which provide Marking rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table.
usdMarkingRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.8.1		not-accessible	A Marking rule entry.
ROW usdMarkingRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.8.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The IP precedence field is mandatory and must be specified. Modes supported are create-and-go and destroy.
I32 usdMarkingTOSByte	1.3.6.1.4.1.4874.2.2.27.1.3.8.1.2	Integer32	read-create	The IP precedence value associated with this policy rule.
I32 usdMarkingMask	1.3.6.1.4.1.4874.2.2.27.1.3.8.1.3	Integer32	read-create	The mask to use for TOS byte checks.
I32 usdMarkingClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.8.1.4	Integer32	read-create	The classifier control list ID which fills out the Marking policy rule.
usdForwardRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.9		not-accessible	A list of entries which provide forward rule data. Creation of an entry in this table results in a corresponding entry being created in the policy rule table.
usdForwardRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.9.1		not-accessible	A forward rule entry.
ROW usdForwardRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.9.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. Modes supported are create-and-go and destroy.
I32 usdForwardClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.9.1.2	Integer32	read-create	The classifier control list ID which completes the forward policy rule.
usdTrafficShapeRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.10		not-accessible	Obsolete list of entries which provide Traffic Shape rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table. This list became obsolete when the policy shaper capability was moved into the quality of service component.
usdTrafficShapeRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.10.1		not-accessible	A TrafficShape rule entry.
ROW usdTrafficShapeRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.10.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The traffic shape profile ID is mandatory and must be specified. Modes supported are create-and-go and destroy.
I32 usdTrafficShapeId	1.3.6.1.4.1.4874.2.2.27.1.3.10.1.2	Integer32	read-create	The RLP ID which provides the rate limit data which completes the traffic shape policy rule.
usdColorRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.11		not-accessible	A list of entries which provide Color rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table.
usdColorRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.11.1		not-accessible	A Color rule entry.
ROW usdColorRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.11.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The color field is mandatory and must be specified. Modes supported are create-and-go and destroy.
INT usdColor	1.3.6.1.4.1.4874.2.2.27.1.3.11.1.2	INTEGER	read-create	The color with which to explicitly color packets associated with this policy rule.
I32 usdColorClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.11.1.3	Integer32	read-create	The classifier control list ID which fills out the Color policy rule.
usdLogRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.12		not-accessible	A list of entries which provide log rule data. Creation of an entry in this table results in a corresponding entry being created in the policy rule table.
usdLogRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.12.1		not-accessible	A log rule entry.
ROW usdLogRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.12.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. Modes supported are create-and-go and destroy.
I32 usdLogClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.12.1.2	Integer32	read-create	The classifier control list ID which completes the log policy rule.
usdTrafficClassRuleTable	1.3.6.1.4.1.4874.2.2.27.1.3.13		not-accessible	A list of entries which provide traffic Class rule data. Creation of entries in the table result in a corresponding entry being created in the policy rule table.
usdTrafficClassRuleEntry	1.3.6.1.4.1.4874.2.2.27.1.3.13.1		not-accessible	A Traffic Class rule entry.
ROW usdTrafficClassRowStatus	1.3.6.1.4.1.4874.2.2.27.1.3.13.1.1	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. The usdTrafficClassId field is mandatory and must be specified. Modes supported are create-and-go and destroy.
I32 usdTrafficClassId	1.3.6.1.4.1.4874.2.2.27.1.3.13.1.2	Integer32	read-create	The traffic class ID.
I32 usdTrafficClassClaclId	1.3.6.1.4.1.4874.2.2.27.1.3.13.1.3	Integer32	read-create	The classifier control list ID which fills out the traffic class policy rule.
usdPolicyIf	1.3.6.1.4.1.4874.2.2.27.1.4
usdPolicyIfTable	1.3.6.1.4.1.4874.2.2.27.1.4.1		not-accessible	This obsolete table contains entries which represent attachment of policies to interfaces. This table became obsolete when the usdPolicyIfAttTable was added.
usdPolicyIfEntry	1.3.6.1.4.1.4874.2.2.27.1.4.1.1		not-accessible	Each entry contains the attachment of policy(s) to an interface.
U32 usdPolicyIfInterfaceId	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.1	Unsigned32	not-accessible	The interface number representing the interface to which policy(s) have been attached.
ROW usdPolicyIfRowStatus	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy * LIMITED ACCESS LIST CONFIGURATION LEVEL * RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create a policy table entry with the associated policy name. destroy Destroy the specified list and all of its constituent elements. Policy row members may not be modified once the row has been created.
I32 usdPolicyIfInputPolicyId	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.3	Integer32	read-create	This object is used to control the attachment of input policies to the interface specified by usdPolicyIfInterfaceId, usdPolicyIfForwardingType and usdPolicyIfPolicyType. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. If so, the attachment is immediate.
I32 usdPolicyIfOutputPolicyId	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.4	Integer32	read-create	This object is used to control the attachment of output policies to the interface specified by usdPolicyIfInterfaceId, usdPolicyIfForwardingType and usdPolicyIfPolicyType. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. If so, the attachment is immediate.
T/F usdPolicyIfInputStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.5	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for an input policy attachment. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The desired value must be set before the policy is attached or in a multiple object varbind. Failure to do so will result in the policy being attached with the previous value of usdPolicyInputStatsEnable.
T/F usdPolicyIfOutputStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.4.1.1.6	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for an output policy attachment. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The desired value must be set before the policy is attached or in a multiple object varbind. Failure to do so will result in the policy being attached with the previous value of usdPolicyOutputStatsEnable.
usdPolicyIfAttachTable	1.3.6.1.4.1.4874.2.2.27.1.4.2		not-accessible	This table contains entries which represent attachment of policies to interfaces.
usdPolicyIfAttachEntry	1.3.6.1.4.1.4874.2.2.27.1.4.2.1		not-accessible	Each entry contains the attachment of policy(s) to an interface.
NUM usdPolicyIfAttachInterfaceId	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.1	InterfaceIndex	not-accessible	The interface number representing the interface to which policy(s) have been attached.
USD usdPolicyIfAttachForwardingType	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.2	UsdPolicyForwardingType	not-accessible	The interface type (i.e. IP or CBF) which the policy have been attached to.
USD usdPolicyIfAttachPolicyType	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.3	UsdPolicyAttachmentType	not-accessible	The policy type (i.e. input, output or local input).
ROW usdPolicyIfAttachRowStatus	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.4	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy * LIMITED ACCESS LIST CONFIGURATION LEVEL * RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create a policy table entry with the associated policy name. destroy Destroy the specified list and all of its constituent elements. Policy row members may not be modified once the row has been created.
I32 usdPolicyIfAttachPolicyId	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.5	Integer32	read-create	This object is used to control the attachment of policies to the interface specified by usdPolicyIfAttachInterfaceId, usdPolicyIfAttachForwardingType and usdPolicyIfAttachPolicyType. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. If so, the attachment is immediate.
T/F usdPolicyIfAttachStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.4.2.1.6	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for a policy attachment. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The desired value must be set before the policy is attached or in a multiple object varbind. Failure to do so will result in the policy being attached with the previous value of usdPolicyStatsEnable.
usdPolicyProfile	1.3.6.1.4.1.4874.2.2.27.1.5
usdPolicyProfileTable	1.3.6.1.4.1.4874.2.2.27.1.5.1		not-accessible	This obsolete table contains entries which represent attachment of policies to dynamic interfaces through profiles. This table became obsolete when the usdPolicyAttachProfileTable was added.
usdPolicyProfileEntry	1.3.6.1.4.1.4874.2.2.27.1.5.1.1		not-accessible	Each entry contains the profile for attachment of policy(s) to a dynamic interface.
U32 usdPolicyProfileId	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.1	Unsigned32	not-accessible	The profile to which the policy attachment profile data belongs. When this profile is applied to a dynamic interface the associated policies will be applied to that interface.
ROW usdPolicyProfileRowStatus	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy * LIMITED ACCESS LIST CONFIGURATION LEVEL * RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create a policy table entry with the associated policy name. destroy Destroy the specified list and all of its constituent elements. Policy row members may not be modified once the row has been created.
I32 usdPolicyProfileInputPolicyId	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.3	Integer32	read-create	This object is used to control the attachment of input policies to dynamic interfaces configured by the profile identified by usdPolicyProfileId. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. Changes made to a row in this table do not take effect until the profile is applied.
I32 usdPolicyProfileOutputPolicyId	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.4	Integer32	read-create	This object is used to control the attachment of output policies to dynamic interfaces configured by the profile identified by usdPolicyProfileId. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. Changes made to a row in this table do not take effect until the profile is applied to an interface.
T/F usdPolicyProfileInputStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.5	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for an input policy attachment performed by a profile. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The changes will not take effect until the profile is applied to an interface.
T/F usdPolicyProfileOutputStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.6	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for an output policy attachment performed by a profile. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The changes will not take effect until the profile is applied to an interface.
I32 usdPolicyProfileLocalInputPolicyId	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.7	Integer32	read-create	This object is used to control the attachment of local input policies to dynamic interfaces configured by the profile identified by usdPolicyProfileId. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. Changes made to a row in this table do not take effect until the profile is applied.
T/F usdPolicyProfileLocalInputStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.5.1.1.8	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for a local input policy attachment performed by a profile. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The changes will not take effect until the profile is applied to an interface.
usdPolicyAttachProfileTable	1.3.6.1.4.1.4874.2.2.27.1.5.2		not-accessible	This table contains entries which represent attachment of policies to dynamic interfaces through profiles.
usdPolicyAttachProfileEntry	1.3.6.1.4.1.4874.2.2.27.1.5.2.1		not-accessible	Each entry contains the profile for attachment of policy(s) to a dynamic interface.
U32 usdPolicyAttachProfileId	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.1	Unsigned32	not-accessible	The profile to which the policy attachment profile data belongs. When this profile is applied to a dynamic interface the associated policies will be applied to that interface.
USD usdPolicyAttachProfileForwardingType	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.2	UsdPolicyForwardingType	not-accessible	The interface type (i.e. IP or CBF) which the policy would be attached to.
USD usdPolicyAttachProfilePolicyType	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.3	UsdPolicyAttachmentType	not-accessible	The policy type (i.e. input, output or local input).
ROW usdPolicyAttachProfileRowStatus	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.4	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy * LIMITED ACCESS LIST CONFIGURATION LEVEL * RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create a policy table entry with the associated policy name. destroy Destroy the specified list and all of its constituent elements. Policy row members may not be modified once the row has been created.
I32 usdPolicyAttachProfilePolicyId	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.5	Integer32	read-create	This object is used to control the attachment of policies to dynamic interfaces configured by the profile identified by usdPolicyAttachProfileId, usdPolicyAttachProfileForwardingType and usdPolicyAttachProfilePolicyType. Attach a policy by setting this value to the ID of the policy. Remove a policy attachment by setting this value to zero. This object may be modified while the row is active. Changes made to a row in this table do not take effect until the profile is applied.
T/F usdPolicyAttachProfileStatsEnable	1.3.6.1.4.1.4874.2.2.27.1.5.2.1.6	TruthValue	read-create	This object is used to control the enabling and disabling of statistics for an policy attachment performed by a profile. Set this object to true to enable statistics. Set this object to false to disable statistics. This object may be modified while the row is active. The changes will not take effect until the profile is applied to an interface.
usdPolicyStatistics	1.3.6.1.4.1.4874.2.2.27.1.6
usdPolicyIfStatsTable	1.3.6.1.4.1.4874.2.2.27.1.6.1		not-accessible	Each entry within this obsolete table contains statistics data for an interface/policy rule combination. Interfaces with policies attached and statistics disabled are not represented in this table.
usdPolicyIfStatsEntry	1.3.6.1.4.1.4874.2.2.27.1.6.1.1		not-accessible	Each entry defines a single statistics entry.
NUM usdPolicyIfStatsIfId	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.1	InterfaceIndex	not-accessible	The interface ID corresponding to the stats block represented by this row.
USD usdPolicyIfStatsPolicyType	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.2	UsdPolicyAttachmentType	not-accessible	The attachment point for the policy.
I32 usdPolicyIfStatsPolicyId	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.3	Integer32	not-accessible	The PolicyTable index of the policy corresponding to the stats block represented by this row.
I32 usdPolicyIfStatsRulePrec	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.4	Integer32	not-accessible	The precedence of the policy rule corresponding to the stats block represented by this row.
I32 usdPolicyIfStatsRuleId	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.5	Integer32	not-accessible	The index of the policy rule corresponding to the stats block represented by this row.
I32 usdPolicyIfStatsClaclEntryNumber	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.6	Integer32	not-accessible	The index of the clacl entry number corresponding to the stats block represented by this row.
C64 usdPolicyIfStatsGreenPackets	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.7	Counter64	read-only	The number of green packets policed by the policy rule.
C64 usdPolicyIfStatsYellowPackets	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.8	Counter64	read-only	The number of yellow packets policed by the policy rule.
C64 usdPolicyIfStatsRedPackets	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.9	Counter64	read-only	The number of red packets policed by the policy rule.
C64 usdPolicyIfStatsGreenBytes	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.10	Counter64	read-only	The number of green bytes policed by the policy rule.
C64 usdPolicyIfStatsYellowBytes	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.11	Counter64	read-only	The number of yellow bytes policed by the policy rule.
C64 usdPolicyIfStatsRedBytes	1.3.6.1.4.1.4874.2.2.27.1.6.1.1.12	Counter64	read-only	The number of red bytes policed by the policy rule.
usdPolicyIfAttachStatsTable	1.3.6.1.4.1.4874.2.2.27.1.6.2		not-accessible	Each entry within this table contains statistics data for an interface/policy rule combination. Interfaces with policies attached and statistics disabled are not represented in this table.
usdPolicyIfAttachStatsEntry	1.3.6.1.4.1.4874.2.2.27.1.6.2.1		not-accessible	Each entry defines a single statistics entry.
NUM usdPolicyIfAttachStatsIfId	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.1	InterfaceIndex	not-accessible	The interface ID corresponding to the stats block represented by this row.
USD usdPolicyIfAttachStatsForwardingType	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.2	UsdPolicyForwardingType	not-accessible	The forwarding type for the policy attachment.
USD usdPolicyIfAttachStatsPolicyType	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.3	UsdPolicyAttachmentType	not-accessible	The attachment point for the policy.
I32 usdPolicyIfAttachStatsPolicyId	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.4	Integer32	not-accessible	The PolicyTable index of the policy corresponding to the stats block represented by this row.
I32 usdPolicyIfAttachStatsRulePrec	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.5	Integer32	not-accessible	The precedence of the policy rule corresponding to the stats block represented by this row.
I32 usdPolicyIfAttachStatsRuleId	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.6	Integer32	not-accessible	The index of the policy rule corresponding to the stats block represented by this row.
I32 usdPolicyIfAttachStatsClaclEntryNumber	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.7	Integer32	not-accessible	The index of the clacl entry number corresponding to the stats block represented by this row.
C64 usdPolicyIfAttachStatsGreenPackets	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.8	Counter64	read-only	The number of green packets policed by the policy rule.
C64 usdPolicyIfAttachStatsYellowPackets	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.9	Counter64	read-only	The number of yellow packets policed by the policy rule.
C64 usdPolicyIfAttachStatsRedPackets	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.10	Counter64	read-only	The number of red packets policed by the policy rule.
C64 usdPolicyIfAttachStatsGreenBytes	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.11	Counter64	read-only	The number of green bytes policed by the policy rule.
C64 usdPolicyIfAttachStatsYellowBytes	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.12	Counter64	read-only	The number of yellow bytes policed by the policy rule.
C64 usdPolicyIfAttachStatsRedBytes	1.3.6.1.4.1.4874.2.2.27.1.6.2.1.13	Counter64	read-only	The number of red bytes policed by the policy rule.
usdTrafficShapeControlList	1.3.6.1.4.1.4874.2.2.27.1.7
I32 usdTrafficShapeProfileNextIndex	1.3.6.1.4.1.4874.2.2.27.1.7.1	Integer32	read-only	Obsolete scalar object returns the index of the next available row in the usdTrafficShapeProfileTable. This object returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that index allocation is unintended. This object became obsolete when the policy shaper capability was moved into the quality of service component.
usdTrafficShapeProfileTable	1.3.6.1.4.1.4874.2.2.27.1.7.2		not-accessible	This table contains entries for elements of Traffic Shape Profile definitions. This table became obsolete when the policy shaper capability was moved into the quality of service component.
usdTrafficShapeProfileEntry	1.3.6.1.4.1.4874.2.2.27.1.7.2.1		not-accessible	Each entry describes the characteristics of a traffic shape profile element.
I32 usdTrafficShapeProfileId	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.1	Integer32	not-accessible	The number of the traffic shape profile entry which is defined by this row.
ROW usdTrafficShapeProfileRowStatus	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.2	RowStatus	read-create	Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: usdTrafficShapeProfileRowStatus
STR usdTrafficShapeProfileName	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.3	DisplayString	read-create	Specifies the name of the traffic shape profile defined by this row.
C32 usdTrafficShapeReferenceCount	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.4	Counter32	read-only	This object reflects the number of times a traffic shape profile object is referenced by policies.
I32 usdTrafficShapeRate	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.5	Integer32	read-create	The traffic shape rate in bits per second.
I32 usdTrafficShapeBurst	1.3.6.1.4.1.4874.2.2.27.1.7.2.1.6	Integer32	read-create	The traffic shape burst in bytes.
usdPolicyConformance	1.3.6.1.4.1.4874.2.2.27.2
usdPolicyCompliances	1.3.6.1.4.1.4874.2.2.27.2.1
usdPolicyCompliance	1.3.6.1.4.1.4874.2.2.27.2.1.1			Obsolete compliance statement for entities which implement the Unisphere policy management MIB. This statement became obsolete when policy traffic shape and color objects were added to the MIB.
usdPolicyCompliance2	1.3.6.1.4.1.4874.2.2.27.2.1.2			Obsolete compliance statement for entities which implement the Unisphere policy management MIB. This statement was obsolete when policy log rule objects were added to the MIB.
usdPolicyCompliance3	1.3.6.1.4.1.4874.2.2.27.2.1.3			Obsolete compliance statement for entities which implement the Unisphere policy management MIB. This statement became obsolete when policy color rule objects were added, the policy profile table was extended and the policy interface attachement tables were replaced by new versions.
usdPolicyCompliance4	1.3.6.1.4.1.4874.2.2.27.2.1.4			Obsolete compliance statement for entities which implement the Unisphere policy management MIB. This statement became obsolete when TCP flag and IP flag classifier control list objects were added and the usdPolicyProfileTable was repalced by the usdPolicyAttachProfileTable.
usdPolicyCompliance5	1.3.6.1.4.1.4874.2.2.27.2.1.5			Obsolete compliance statement for entities which implement the Unisphere policy management MIB. This statement became obsolete when traffic class rule objects and new rate limit objects were added and when the policy shaper capability was moved into the quality of service component.
usdPolicyCompliance6	1.3.6.1.4.1.4874.2.2.27.2.1.6			The compliance statement for entities which implement the Unisphere policy management MIB.
usdPolicyGroups	1.3.6.1.4.1.4874.2.2.27.2.2
usdPolicyGroup	1.3.6.1.4.1.4874.2.2.27.2.2.1			Obsolete collection of objects for managing policies in a Unisphere product. This group became obsolete when policy traffic shape and color objects were added.
usdRateLimitControlListGroup	1.3.6.1.4.1.4874.2.2.27.2.2.2			Obsolete collection of objects for managing rate limit control lists in a Unisphere product. This group became obsolete when it was replaced by the usdRateLimitGroup so that rate limit support could become optional.
usdClassifierControlListGroup	1.3.6.1.4.1.4874.2.2.27.2.2.3			Obsolete collection of objects for managing elements of classifier control lists in a Unisphere product. This group became obsolete when support was added for TCP flag and IP flag control objects.
usdPolicyIfGroup	1.3.6.1.4.1.4874.2.2.27.2.2.4			Obsolete collection of objects for managing attachment of policies to interfaces in a Unisphere product. This group became obsolete when the usdPolicyIfTable was replaced by the usdPolicyIfAttachTable.
usdPolicyProfileGroup	1.3.6.1.4.1.4874.2.2.27.2.2.5			Obsolete collection of objects for managing attachment of policies to dynamic interfaces through profiles in a Unisphere product. This group became obsolete when the usdPolicyProfileLocalInputPolicyId and the usdPolicyProfileLocalInputStatsEnable objects were added.
usdPolicyStatisticsGroup	1.3.6.1.4.1.4874.2.2.27.2.2.6			Obsolete collection of objects for managing statistics data for an interface/policy rule combination in a Unisphere product. This group became obsolete when the usdPolicyIfStatsTable was replaced by the usdPolicyIfAttachStatsTable.
usdPolicyGroup2	1.3.6.1.4.1.4874.2.2.27.2.2.7			Obsolete collection of objects for managing policies in a Unisphere product. This group became obsolete when the specific rules objects were broken out into separte groups.
usdTrafficShapeProfileGroup	1.3.6.1.4.1.4874.2.2.27.2.2.8			Obsolete collection of objects for traffic shaping data for a policy rule in a Unisphere product. This group became obsolete when it was combined with the traffic shape policy rules objects.
usdLogRuleGroup	1.3.6.1.4.1.4874.2.2.27.2.2.9			A collection of objects for log data for a policy rule in a Unisphere product.
usdPolicyIfAttachGroup	1.3.6.1.4.1.4874.2.2.27.2.2.10			A collection of objects for managing attachment of policies to interfaces in a Unisphere product.
usdPolicyProfileGroup2	1.3.6.1.4.1.4874.2.2.27.2.2.11			Obsolete collection of objects for managing attachment of policies to dynamic interfaces through profiles. This group became obsolete when the usdPolicyProfileTable was replaced by the usdPolicyAttachProfileTable.
usdPolicyAttachStatisticsGroup	1.3.6.1.4.1.4874.2.2.27.2.2.12			A collection of objects for managing statistics data for an interface/policy rule combination in a Unisphere product.
usdClassifierControlListGroup2	1.3.6.1.4.1.4874.2.2.27.2.2.13			A collection of objects for managing elements of classifier control lists in a Unisphere product.
usdPolicyAttachProfileGroup	1.3.6.1.4.1.4874.2.2.27.2.2.14			A collection of objects for managing attachment of policies to dynamic interfaces through profiles.
usdPolicyBaseGroup	1.3.6.1.4.1.4874.2.2.27.2.2.15			A collection of basic objects for managing policies in a Unisphere product.
usdNextHopRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.16			A collection of objects for managing next-hop policy rules in a Unisphere product.
usdFilterRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.17			A collection of objects for managing filter policy rules in a Unisphere product.
usdNextInterfaceRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.18			A collection of objects for managing next-interface policy rules in a Unisphere product.
usdRateLimitGroup	1.3.6.1.4.1.4874.2.2.27.2.2.19			Obsolete collection of objects for managing rate limit policy rules and profile lists in a Unisphere product. This group became obsolete when new rate limit profile objects were added.
usdMarkingRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.20			A collection of objects for managing policy rules for marking in a Unisphere product.
usdForwardRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.21			A collection of objects for managing forward policy rules in a Unisphere product.
usdTrafficShapeGroup	1.3.6.1.4.1.4874.2.2.27.2.2.22			Obsolete collection of objects for managing traffic shape policy rules and profile lists in a Unisphere product. This group became obsolete when the policy shaper capability was moved into the quality of service component.
usdColorRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.23			A collection of objects for managing color policy rules in a Unisphere product.
usdTrafficClassRulesGroup	1.3.6.1.4.1.4874.2.2.27.2.2.24			A collection of objects for managing traffic class policy rules in a Unisphere product.
usdRateLimitGroup2	1.3.6.1.4.1.4874.2.2.27.2.2.25			A collection of objects for managing rate limit policy rules and profile lists in a Unisphere product.

RFC description

Juniper Networks/Unisphere MIB for managing policy configuration and enforcement on Juniper routing and network equipment.

Start monitoring Juniper/Unisphere ERX edge router (QoS/traffic-policy admin/oper status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Unisphere-Data-POLICY-MIB