All MIBs › Unisphere-Data-L2TP-MIB
Organization: Unisphere Networks, Inc.
Last Updated: 2001-10-17
Category: Juniper Unisphere ERX Routing, WAN and Transport Protocols
Description: Manages Unisphere ERX L2TP tunnel and session configuration, control channel, and statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Unisphere-Data-L2TP-MIB?
Unisphere-Data-L2TP-MIB is a vendor MIB for Unisphere/Juniper ERX edge routers covering the L2TP (Layer 2 Tunneling Protocol) subsystem used for tunneling PPP sessions from broadband access concentrators to service-provider networks. It exposes system-wide L2TP configuration (admin state, tunnel idle/destruct timeouts, control retransmissions, tunnel switching) and status objects (protocol version, vendor name, firmware revision, total and failed destination counts), along with trap-control settings and notifications. Its monitoring value is both software/protocol-state and fault-oriented: tracking tunnel establishment success versus failed destinations gives direct insight into L2TP service health, and firmware revision reporting supports software-version auditing. It builds on general tunneling concepts akin to those in the IETF L2TP MIB work, though implemented as a Unisphere-specific enterprise module. It is deployed on Juniper/Unisphere ERX broadband routers acting as LNS/LAC endpoints in DSL or dial access networks. Network engineers evaluating or troubleshooting this functionality can download the Unisphere-Data-L2TP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Unisphere-Data-L2TP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper/Unisphere ERX edge routing switch (LAC/LNS)
Monitoring Examples
An operator would poll usdL2tpSysStatusTotalDestinations against usdL2tpSysStatusFailedDestinations to gauge the health of L2TP tunnel endpoints, with a rising failed-destination count indicating tunnel setup problems to specific LNS/LAC peers. usdL2tpSysStatusFirmwareRev and usdL2tpSysStatusVendorName would be checked during a software audit, while usdL2tpSysConfigTunnelIdleTimeout and usdL2tpSysConfigAdminState confirm the tunneling service is administratively enabled with the expected idle-timeout policy. usdL2tpTraps would notify on tunnel state changes without requiring constant polling.
What Can Be Monitored
- L2TP admin state
- tunnel idle and destruct timeouts
- total and failed tunnel destinations
- protocol version and firmware revision
- tunnel switching status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From Unisphere-Data-MIBs
| usDataMibs | MODULE-IDENTITY |
From Unisphere-Data-TC
| UsdEnable |
How to Use in IPNetwork Monitor
Example using usdL2tpSysStatusTotalDestinations OID:
Select a Juniper/Unisphere ERX edge routing switch, LAC/LN (L2TP tunnel/destination-count status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type usdL2tpSysStatusTotalDestinations into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of destination creations attempted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| usdL2tpMIB | 1.3.6.1.4.1.4874.2.2.35 | The L2TP MIB for the Unisphere Networks enterprise. | ||
| usdL2tpTraps | 1.3.6.1.4.1.4874.2.2.35.0 | |||
| usdL2tpObjects | 1.3.6.1.4.1.4874.2.2.35.1 | |||
| usdL2tpSystem | 1.3.6.1.4.1.4874.2.2.35.1.1 | |||
| usdL2tpSystemConfig | 1.3.6.1.4.1.4874.2.2.35.1.1.1 | |||
| USD usdL2tpSysConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.1.1.1 | UsdL2tpAdminState | read-write | Exerts control over all L2TP tunnels/sessions in the system. |
| I32 usdL2tpSysConfigDestructTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.2 | Integer32 | read-write | The amount of time, in seconds, to preserve dynamic tunnels/sessions after they become inactive, e.g. to poll their statistics. |
| USD usdL2tpSysConfigIpChecksumEnable | 1.3.6.1.4.1.4874.2.2.35.1.1.1.3 | UsdEnable | read-write | Enable/disable IP checksumming for tunnels with UDP/IP transport. |
| USD usdL2tpSysConfigTunnelSwitchingEnabled | 1.3.6.1.4.1.4874.2.2.35.1.1.1.4 | UsdEnable | read-write | Tunnel switching enabled/disable. |
| I32 usdL2tpSysConfigControlRetransmissions | 1.3.6.1.4.1.4874.2.2.35.1.1.1.5 | Integer32 | read-write | The number of retransmission retries allowed before control session goes down. |
| I32 usdL2tpSysConfigTunnelIdleTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.6 | Integer32 | read-write | Idle tunnel remains active for the specified amount of time; value 0 disables the timer i.e. tunnel becomes persistent. |
| USD usdL2tpSysConfigReceiveDataSequencingIgnore | 1.3.6.1.4.1.4874.2.2.35.1.1.1.7 | UsdEnable | read-write | Enable/disable ignoring of receive sequencing of L2TP data packets. |
| usdL2tpSystemStatus | 1.3.6.1.4.1.4874.2.2.35.1.1.2 | |||
| OCT usdL2tpSysStatusProtocolVersion | 1.3.6.1.4.1.4874.2.2.35.1.1.2.1 | OCTET STRING | read-only | Vector of supported L2TP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the version and the second octet contains the revision. |
| STR usdL2tpSysStatusVendorName | 1.3.6.1.4.1.4874.2.2.35.1.1.2.2 | DisplayString | read-only | Vendor name of the L2TP protocol stack. |
| I32 usdL2tpSysStatusFirmwareRev | 1.3.6.1.4.1.4874.2.2.35.1.1.2.3 | Integer32 | read-only | Firmware revision for the L2TP protocol stack. |
| C32 usdL2tpSysStatusTotalDestinationsEx | 1.3.6.1.4.1.4874.2.2.35.1.1.2.4 | Counter32 | read-only | Number of destination creations attempted. |
| C32 usdL2tpSysStatusFailedDestinations | 1.3.6.1.4.1.4874.2.2.35.1.1.2.5 | Counter32 | read-only | Number of destination creation attempts that failed. |
| G32 usdL2tpSysStatusActiveDestinations | 1.3.6.1.4.1.4874.2.2.35.1.1.2.6 | Gauge32 | read-only | Number of destinations having at least one active tunnel. |
| C32 usdL2tpSysStatusTotalTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.7 | Counter32 | read-only | Number of tunnel creations attempted. |
| C32 usdL2tpSysStatusFailedTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.8 | Counter32 | read-only | Number of tunnel creation attempts that failed to reach the established state. |
| C32 usdL2tpSysStatusFailedTunnelAuthens | 1.3.6.1.4.1.4874.2.2.35.1.1.2.9 | Counter32 | read-only | Number of tunnel creation attempts that failed authentication. |
| G32 usdL2tpSysStatusActiveTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.10 | Gauge32 | read-only | Number of tunnels currently established. |
| C32 usdL2tpSysStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.11 | Counter32 | read-only | Number of session creations attempted. |
| C32 usdL2tpSysStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.12 | Counter32 | read-only | Number of session creation attempts that failed to reach the established state. |
| G32 usdL2tpSysStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.13 | Gauge32 | read-only | Number of sessions currently established. |
| usdL2tpDestination | 1.3.6.1.4.1.4874.2.2.35.1.2 | |||
| usdL2tpDestConfig | 1.3.6.1.4.1.4874.2.2.35.1.2.1 | |||
| usdL2tpDestConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2 | not-accessible | The L2TP destination configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpDestStatsTable. | |
| usdL2tpDestConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP destination. | |
| NUM usdL2tpDestConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW usdL2tpDestConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| USD usdL2tpDestConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.3 | UsdL2tpAdminState | read-create | The configured administrative state. |
| usdL2tpDestStatus | 1.3.6.1.4.1.4874.2.2.35.1.2.2 | |||
| usdL2tpDestStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1 | not-accessible | The L2TP destination status table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpDestConfigTable. | |
| usdL2tpDestStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1 | not-accessible | Describes the status attributes of an L2TP destination. | |
| NUM usdL2tpDestStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| USD usdL2tpDestStatusTransport | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.2 | UsdL2tpTransport | read-only | The underlying transport over which this L2TP destination is carried. |
| USD usdL2tpDestStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.3 | UsdL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this destination, or an overriding admin state exerted from a higher hierarchical level (system). |
| C32 usdL2tpDestStatusTotalTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.4 | Counter32 | read-only | Number of tunnel creations attempted. |
| C32 usdL2tpDestStatusFailedTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.5 | Counter32 | read-only | Number of tunnel creation attempts that failed to reach the established state. |
| C32 usdL2tpDestStatusFailedTunnelAuthens | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.6 | Counter32 | read-only | Number of tunnel creation attempts that failed authentication. |
| G32 usdL2tpDestStatusActiveTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.7 | Gauge32 | read-only | Number of tunnels currently established. |
| C32 usdL2tpDestStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.8 | Counter32 | read-only | Number of session creations attempted. |
| C32 usdL2tpDestStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.9 | Counter32 | read-only | Number of session creation attempts that failed to reach the established state. |
| G32 usdL2tpDestStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.10 | Gauge32 | read-only | Number of sessions currently established. |
| usdL2tpDestStatistics | 1.3.6.1.4.1.4874.2.2.35.1.2.3 | |||
| usdL2tpDestStatTable | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1 | not-accessible | The L2TP destination statistics table. Describes the aggregate control and payload statistics for all L2TP tunnels configured on each destination. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpDestConfigTable. | |
| usdL2tpDestStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1 | not-accessible | Describes the aggregate L2TP control and payload statistics for all L2TP tunnels on an L2TP destination. | |
| NUM usdL2tpDestStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| C32 usdL2tpDestStatCtlRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.2 | Counter32 | read-only | Number of control octets received. |
| C32 usdL2tpDestStatCtlRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.3 | Counter32 | read-only | Number of control packets received. |
| C32 usdL2tpDestStatCtlRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.4 | Counter32 | read-only | Number of control packets incurring reception errors. |
| C32 usdL2tpDestStatCtlRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.5 | Counter32 | read-only | Number of control packets discarded after reception. |
| C32 usdL2tpDestStatCtlSendOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.6 | Counter32 | read-only | Number of control octets sent. |
| C32 usdL2tpDestStatCtlSendPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.7 | Counter32 | read-only | Number of control packets sent. |
| C32 usdL2tpDestStatCtlSendErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.8 | Counter32 | read-only | Number of control packets incurring transmission errors. |
| C32 usdL2tpDestStatCtlSendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.9 | Counter32 | read-only | Number of control packets discarded before transmission. |
| C32 usdL2tpDestStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.10 | Counter32 | read-only | Number of payload octets received. |
| C32 usdL2tpDestStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.11 | Counter32 | read-only | Number of payload packets received. |
| C32 usdL2tpDestStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.12 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 usdL2tpDestStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.13 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 usdL2tpDestStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.14 | Counter32 | read-only | Number of payload octets sent. |
| C32 usdL2tpDestStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.15 | Counter32 | read-only | Number of payload packets sent. |
| C32 usdL2tpDestStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.16 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 usdL2tpDestStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.17 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| usdL2tpTunnel | 1.3.6.1.4.1.4874.2.2.35.1.3 | |||
| usdL2tpTunnelConfig | 1.3.6.1.4.1.4874.2.2.35.1.3.1 | |||
| usdL2tpTunnelConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2 | not-accessible | The L2TP tunnel configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpTunnelStatsTable. | |
| usdL2tpTunnelConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP tunnel. | |
| NUM usdL2tpTunnelConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW usdL2tpTunnelConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| USD usdL2tpTunnelConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.3 | UsdL2tpAdminState | read-create | The configured administrative state. |
| usdL2tpTunnelStatus | 1.3.6.1.4.1.4874.2.2.35.1.3.2 | |||
| usdL2tpTunnelStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1 | not-accessible | The L2TP tunnel status and statistics table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpTunnelConfigTable. | |
| usdL2tpTunnelStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1 | not-accessible | An L2TP tunnel interface stats entry. | |
| NUM usdL2tpTunnelStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.1 | InterfaceIndex | not-accessible | Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| USD usdL2tpTunnelStatusTransport | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.2 | UsdL2tpTransport | read-only | The underlying transport over which this L2TP tunnel is carried. |
| USD usdL2tpTunnelStatusLocalTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.3 | UsdL2tpTunnelId | read-only | The local tunnel identifier. |
| USD usdL2tpTunnelStatusRemoteTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.4 | UsdL2tpTunnelId | read-only | The remote tunnel identifier. |
| USD usdL2tpTunnelStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.5 | UsdL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this tunnel, or an overriding admin state exerted from a higher hierarchical level (system, destination). |
| INT usdL2tpTunnelStatusState | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.6 | INTEGER | read-only | The current state of the tunnel. |
| INT usdL2tpTunnelStatusInitiated | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.7 | INTEGER | read-only | Indicates whether the tunnel was initiated locally, or by the remote tunnel peer. |
| STR usdL2tpTunnelStatusRemoteHostName | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.8 | DisplayString | read-only | The host name obtained during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero-length string if no name was previously known. |
| STR usdL2tpTunnelStatusRemoteVendorName | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.9 | DisplayString | read-only | Identifies the vendor name of the peer's L2TP implementation. If the tunnel is idle, this object should maintain its value from the last time it was connected, of a zero-length string if no name was previously known. |
| I32 usdL2tpTunnelStatusRemoteFirmwareRevision | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.10 | Integer32 | read-only | The tunnel peer's firmware revision number. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero value if no revision was previously known. |
| OCT usdL2tpTunnelStatusRemoteProtocolVersion | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.11 | OCTET STRING | read-only | The protocol version and revision of the tunnel peer's implementation. The first octet contains the protocol version. The second octet contains the protocol revision. |
| INT usdL2tpTunnelStatusRemoteBearerCapabilities | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.12 | INTEGER | read-only | The Bearer Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known. |
| INT usdL2tpTunnelStatusRemoteFramingCapabilities | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.13 | INTEGER | read-only | The Framing Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known. |
| G32 usdL2tpTunnelStatusRecvWindowSize | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.14 | Gauge32 | read-only | The receive window size. |
| G32 usdL2tpTunnelStatusSendWindowSize | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.15 | Gauge32 | read-only | The tunnel peer's receive window size. |
| G32 usdL2tpTunnelStatusSendQueueDepth | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.16 | Gauge32 | read-only | Number of control packets on transmit queue. |
| I32 usdL2tpTunnelStatusRecvSeq | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.17 | Integer32 | read-only | The next sequence number expected in a received control packet. |
| I32 usdL2tpTunnelStatusRecvSeqAck | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.18 | Integer32 | read-only | The last received sequence number that was acknowledged back to the tunnel peer. |
| I32 usdL2tpTunnelStatusSendSeq | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.19 | Integer32 | read-only | The next sequence number to be sent in a transmitted control packet. |
| I32 usdL2tpTunnelStatusSendSeqAck | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.20 | Integer32 | read-only | The send sequence number that the tunnel peer has acknowledged. The flow control state can be determined by subtracting the usdL2tpTunnelStatusSendSeq from usdL2tpTunnelStatusSendSeqAck and comparing this value to usdL2tpTunnelStatusSendWindowSize. |
| C32 usdL2tpTunnelStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.21 | Counter32 | read-only | The total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created, including those that have since terminated. |
| C32 usdL2tpTunnelStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.22 | Counter32 | read-only | The number of sessions that were initiated but failed to reach the established phase. |
| G32 usdL2tpTunnelStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.23 | Gauge32 | read-only | The current number of sessions in the established state. |
| I32 usdL2tpTunnelStatusLastResultCode | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.24 | Integer32 | read-only | The last value of the result code as described in the Result Code AVP which caused the tunnel to disconnect. |
| I32 usdL2tpTunnelStatusLastErrorCode | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.25 | Integer32 | read-only | The last value of the error code as described in the Result Code AVP which caused the tunnel to disconnect. |
| STR usdL2tpTunnelStatusLastErrorMessage | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.26 | DisplayString | read-only | The last value of the optional message as described in the Result Code AVP which caused the tunnel to disconnect. |
| U32 usdL2tpTunnelStatusCumEstabTime | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.27 | Unsigned32 | read-only | The cumulative time in seconds that this tunnel, since first being created, has spent in the established state (which may be punctuated by intervals outside the established state). |
| usdL2tpTunnelStatistics | 1.3.6.1.4.1.4874.2.2.35.1.3.3 | |||
| usdL2tpTunnelStatTable | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1 | not-accessible | The L2TP tunnel statistics table. Describes the control and payload statistics for each L2TP tunnel. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpTunnelConfigTable. | |
| usdL2tpTunnelStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1 | not-accessible | Describes the L2TP control and payload statistics for an L2TP tunnel. | |
| NUM usdL2tpTunnelStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| C32 usdL2tpTunnelStatCtlRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.2 | Counter32 | read-only | Number of control octets received. |
| C32 usdL2tpTunnelStatCtlRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.3 | Counter32 | read-only | Number of control packets received. |
| C32 usdL2tpTunnelStatCtlRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.4 | Counter32 | read-only | Number of control packets incurring reception errors. |
| C32 usdL2tpTunnelStatCtlRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.5 | Counter32 | read-only | Number of control packets discarded after reception. |
| C32 usdL2tpTunnelStatCtlSendOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.6 | Counter32 | read-only | Number of control octets sent. |
| C32 usdL2tpTunnelStatCtlSendPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.7 | Counter32 | read-only | Number of control packets sent. |
| C32 usdL2tpTunnelStatCtlSendErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.8 | Counter32 | read-only | Number of control packets incurring transmission errors. |
| C32 usdL2tpTunnelStatCtlSendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.9 | Counter32 | read-only | Number of control packets discarded before transmission. |
| C32 usdL2tpTunnelStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.10 | Counter32 | read-only | Number of payload octets received. |
| C32 usdL2tpTunnelStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.11 | Counter32 | read-only | Number of payload packets received. |
| C32 usdL2tpTunnelStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.12 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 usdL2tpTunnelStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.13 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 usdL2tpTunnelStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.14 | Counter32 | read-only | Number of payload octets sent. |
| C32 usdL2tpTunnelStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.15 | Counter32 | read-only | Number of payload packets sent. |
| C32 usdL2tpTunnelStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.16 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 usdL2tpTunnelStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.17 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| C32 usdL2tpTunnelStatCtlRecvZLB | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.18 | Counter32 | read-only | Number of Zero Length Body control packet acknowledgement packets that were received. |
| C32 usdL2tpTunnelStatCtlRecvOutOfSequence | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.19 | Counter32 | read-only | Number of control packets not received in the correct sequence number order. |
| C32 usdL2tpTunnelStatCtlRecvOutOfWindow | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.20 | Counter32 | read-only | Number of control packets received outside the offered receive window. |
| C32 usdL2tpTunnelStatCtlSendZLB | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.21 | Counter32 | read-only | Number of Zero Length Body control packets sent. |
| C32 usdL2tpTunnelStatCtlSendRetransmits | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.22 | Counter32 | read-only | Number of control packet send retransmissions. |
| usdL2tpTunnelMap | 1.3.6.1.4.1.4874.2.2.35.1.3.4 | |||
| usdL2tpMapTifSidToSifTable | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1 | not-accessible | Table of TunnelIf/SessionId -> SessionIf mappings. | |
| usdL2tpMapTifSidToSifEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1 | not-accessible | A mapping of TunnelIf/SessionId to SessionIf. | |
| NUM usdL2tpMapTifSidToSifTunnelIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of a tunnel interface. |
| USD usdL2tpMapTifSidToSifLocalSessionId | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.2 | UsdL2tpSessionId | not-accessible | A local session ID on the associated tunnel interface. |
| NUM usdL2tpMapTifSidToSifSessionIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.3 | InterfaceIndex | read-only | The ifIndex of the session interface identified by this entry's Tunnel ifIndex and local Session Id pair. |
| usdL2tpMapTidToTifTable | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2 | not-accessible | Map L2TP tunnel IDs to tunnel interfaces. | |
| usdL2tpMapTidToTifEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1 | not-accessible | A mapping of L2TP tunnel ID to tunnel interface. | |
| USD usdL2tpMapTidToTifLocalTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1.1 | UsdL2tpTunnelId | not-accessible | A local tunnel identifier. |
| NUM usdL2tpMapTidToTifIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1.2 | InterfaceIndex | read-only | The ifIndex of the tunnel interface having the associated tunnel identifier. |
| usdL2tpSession | 1.3.6.1.4.1.4874.2.2.35.1.4 | |||
| usdL2tpSessionConfig | 1.3.6.1.4.1.4874.2.2.35.1.4.1 | |||
| usdL2tpSessionConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2 | not-accessible | The L2TP session configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in usdL2tpSessionStatsTable. | |
| usdL2tpSessionConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP session. | |
| NUM usdL2tpSessionConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW usdL2tpSessionConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| USD usdL2tpSessionConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.3 | UsdL2tpAdminState | read-create | The configured administrative state. |
| usdL2tpSessionStatus | 1.3.6.1.4.1.4874.2.2.35.1.4.2 | |||
| usdL2tpSessionStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1 | not-accessible | The L2TP session status and statistics table. | |
| usdL2tpSessionStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1 | not-accessible | An L2TP session interface status and statistics entry. | |
| NUM usdL2tpSessionStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of an L2TP session interface. |
| NUM usdL2tpSessionStatusLacPppIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.2 | InterfaceIndexOrZero | read-only | For pass-through PPP sessions (conventional LAC), the ifIndex of an associated local PPP interface through which the remote LAC client was connected. If unknown, this object contains a value of zero. For locally originated PPP sessions (LNS-like), this object has a value of zero. This object is deprecated in favor of usdL2tpSessionStatusLacTunneledIfIndex. |
| USD usdL2tpSessionStatusLocalSessionId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.3 | UsdL2tpSessionId | read-only | The local session ID for the session. |
| USD usdL2tpSessionStatusRemoteSessionId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.4 | UsdL2tpSessionId | read-only | The remote session ID for the session. |
| STR usdL2tpSessionStatusUserName | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.5 | DisplayString | read-only | The peer session name on this interface, typically the login name of the remote user. If the user name is unknown this object will contain a zero-length string. |
| USD usdL2tpSessionStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.6 | UsdL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this session, or an overriding admin state exerted from a higher hierarchical level (system, destination, tunnel). |
| INT usdL2tpSessionStatusState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.7 | INTEGER | read-only | The current state of the session. |
| INT usdL2tpSessionStatusCallType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.8 | INTEGER | read-only | The type of call and role this tunnel peer is providing for this session. For example, lacIncoming(1) indicates this tunnel peer is acting as a LAC and generated a Incoming-Call-Request to the tunnel peer (the LNS). Note that tunnel peers can be both LAC and LNS simultaneously. |
| I32 usdL2tpSessionStatusCallSerialNumber | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.9 | Integer32 | read-only | The serial number assigned to this session. |
| I32 usdL2tpSessionStatusTxConnectSpeed | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.10 | Integer32 | read-only | The last known transmit baud rate for this session. |
| I32 usdL2tpSessionStatusRxConnectSpeed | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.11 | Integer32 | read-only | The last known receive baud rate for this session. |
| INT usdL2tpSessionStatusCallBearerType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.12 | INTEGER | read-only | The bearer type of this session. |
| INT usdL2tpSessionStatusFramingType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.13 | INTEGER | read-only | The framing type of this session. |
| I32 usdL2tpSessionStatusPhysChanId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.14 | Integer32 | read-only | The physical channel identifier for the session. For pass-through PPP sessions, typically the ifIndex of the access interface lying below the PPP interface identified by usdL2tpSessionStatusLacTunneledIfIndex. |
| STR usdL2tpSessionStatusDnis | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.15 | DisplayString | read-only | The Dialed Number Information String that the LAC obtained from the network for the session. If no DNIS was provided, a zero-length string will be returned. |
| STR usdL2tpSessionStatusClid | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.16 | DisplayString | read-only | The Calling Line ID that the LAC obtained from the network for the session. If no CLID was provided, a zero-length string will be returned. |
| STR usdL2tpSessionStatusSubAddress | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.17 | DisplayString | read-only | The SubAddress that the LAC obtained from the network for the session. If no SubAddress was provided, a zero-length string will be returned. |
| STR usdL2tpSessionStatusPrivateGroupId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.18 | DisplayString | read-only | The Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided, a zero-length string will be returned. |
| T/F usdL2tpSessionStatusProxyLcp | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.19 | TruthValue | read-only | Indicates whether the LAC performed proxy LCP for this session. |
| INT usdL2tpSessionStatusAuthMethod | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.20 | INTEGER | read-only | The proxy authentication method employed by the LAC for the session. If usdL2tpSessionProxyLcp is false(2) this object reports a value of 'none' and should be ignored. |
| INT usdL2tpSessionStatusSequencingState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.21 | INTEGER | read-only | Indicates which tunnel peers have requested payload sequencing. |
| I32 usdL2tpSessionStatusSendSeq | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.22 | Integer32 | read-only | The next send sequence number. |
| I32 usdL2tpSessionStatusRecvSeq | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.23 | Integer32 | read-only | The next receive sequence number expected. |
| NUM usdL2tpSessionStatusLacTunneledIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.24 | InterfaceIndexOrZero | read-only | For pass-through remote client sessions (conventional LAC), the ifIndex of an associated local interface through which the remote LAC client was connected. If unknown, this object contains a value of zero. For locally originated sessions (LNS-like), this object has a value of zero. |
| U32 usdL2tpSessionStatusCumEstabTime | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.25 | Unsigned32 | read-only | The cumulative time in seconds that this session, since first being created, has spent in the established state (which may be punctuated by intervals outside the established state). |
| usdL2tpSessionStatistics | 1.3.6.1.4.1.4874.2.2.35.1.4.3 | |||
| usdL2tpSessionStatTable | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1 | not-accessible | The L2TP session statistics table. | |
| usdL2tpSessionStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1 | not-accessible | An L2TP session interface statistics entry. | |
| NUM usdL2tpSessionStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of an L2TP session interface. |
| C32 usdL2tpSessionStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.2 | Counter32 | read-only | Number of payload octets received. |
| C32 usdL2tpSessionStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.3 | Counter32 | read-only | Number of payload packets received. |
| C32 usdL2tpSessionStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.4 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 usdL2tpSessionStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.5 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 usdL2tpSessionStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.6 | Counter32 | read-only | Number of payload octets sent. |
| C32 usdL2tpSessionStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.7 | Counter32 | read-only | Number of payload packets sent. |
| C32 usdL2tpSessionStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.8 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 usdL2tpSessionStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.9 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| C32 usdL2tpSessionStatRecvOutOfSequence | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.10 | Counter32 | read-only | The number of packets received out of sequence. |
| C32 usdL2tpSessionStatResequencingTimeouts | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.11 | Counter32 | read-only | The number of reassembly timeouts that have occurred. |
| U32 usdL2tpSessionStatPayLostPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.12 | Unsigned32 | read-only | When sequence numbers are enabled, this value represents the estimated number of payload packets lost, based on observed gaps in sequence numbers. This estimate is subject to correction (decrement) upon receipt of out-of-sequence packets that fill previously observed gaps. |
| usdL2tpTransport | 1.3.6.1.4.1.4874.2.2.35.1.5 | |||
| usdL2tpTransportUdpIp | 1.3.6.1.4.1.4874.2.2.35.1.5.1 | |||
| usdL2tpUdpIpSystem | 1.3.6.1.4.1.4874.2.2.35.1.5.1.1 | |||
| usdL2tpUdpIpDestination | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2 | |||
| usdL2tpUdpIpDestTable | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1 | not-accessible | The L2TP UDP/IP destination table. Reports the UDP/IP characteristics of a L2TP UDP/IP destination. A L2TP UDP/IP destination is associated with a local router, a local IP address, and with a remote IP address for the L2TP peer. More specific UDP/IP detail per tunnel is reported in the usdL2tpUdpIpTunnelTable. | |
| usdL2tpUdpIpDestEntry | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1 | not-accessible | Describes the UDP/IP attributes of an L2TP destination. | |
| NUM usdL2tpUdpIpDestIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| U32 usdL2tpUdpIpDestRouterIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.2 | Unsigned32 | read-only | The index of an entry in the usdRouterTable for the local router with which this L2TP destination interface is associated. |
| IP usdL2tpUdpIpDestLocalAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.3 | IpAddress | read-only | This L2TP destination's local IP address. |
| IP usdL2tpUdpIpDestRemoteAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.4 | IpAddress | read-only | The IP address of the remote L2TP endpoint. |
| usdL2tpUdpIpTunnel | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3 | |||
| usdL2tpUdpIpTunnelTable | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1 | not-accessible | The L2TP UDP/IP tunnel table. Reports the UDP/IP characteristics of L2TP UDP/IP tunnels. A L2TP UDP/IP tunnel is defined in terms of the local and remote IP addresses and UDP ports. | |
| usdL2tpUdpIpTunnelEntry | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1 | not-accessible | An L2TP UDP/IP tunnel entry. | |
| NUM usdL2tpUdpIpTunnelIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.1 | InterfaceIndex | not-accessible | Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| U32 usdL2tpUdpIpTunnelRouterIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.2 | Unsigned32 | read-only | The index of an entry in the usdRouterTable for the local router with which this L2TP tunnel interface is associated. |
| IP usdL2tpUdpIpTunnelLocalAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.3 | IpAddress | read-only | The local IP address for this UDP/IP tunnel. |
| I32 usdL2tpUdpIpTunnelLocalPort | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.4 | Integer32 | read-only | The local UDP port for this UDP/IP tunnel. |
| IP usdL2tpUdpIpTunnelRemoteAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.5 | IpAddress | read-only | The remote IP address for this UDP/IP tunnel. |
| I32 usdL2tpUdpIpTunnelRemotePort | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.6 | Integer32 | read-only | The remote UDP port for this UDP/IP tunnel. |
| usdL2tpUdpIpSession | 1.3.6.1.4.1.4874.2.2.35.1.5.1.4 | |||
| usdL2tpTrapControl | 1.3.6.1.4.1.4874.2.2.35.2 | |||
| usdL2tpConformance | 1.3.6.1.4.1.4874.2.2.35.3 | |||
| usdL2tpGroups | 1.3.6.1.4.1.4874.2.2.35.3.1 | |||
| usdL2tpConfigGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.1 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when usdL2tpSysConfigReceiveDataSequencingIgnore was added. | ||
| usdL2tpStatusGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.2 | Obsolete collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels. This group became obsolete when new objects were added. | ||
| usdL2tpStatGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.3 | Obsolete collection of objects providing statistics of the L2TP protocol at the destination, tunnel, and session levels. This group became obsolete when new objects were added. | ||
| usdL2tpMapGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.4 | A collection of objects providing mapping associations among L2TP components. | ||
| usdL2tpUdpIpGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.5 | A collection of objects providing UDP/IP transport information for L2TP components. | ||
| usdL2tpStatusGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.6 | A collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels. | ||
| usdL2tpStatGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.7 | A collection of objects providing statistics of the L2TP protocol at the destination, tunnel, and session levels. | ||
| usdL2tpConfigGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.8 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when new objects were added. | ||
| usdL2tpConfigGroup3 | 1.3.6.1.4.1.4874.2.2.35.3.1.9 | A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| usdL2tpCompliances | 1.3.6.1.4.1.4874.2.2.35.3.2 | |||
| usdL2tpCompliance | 1.3.6.1.4.1.4874.2.2.35.3.2.1 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when usdL2tpTunnelStatusCumEstabTime, usdL2tpSessionStatusCumEstabTime and usdL2tpSessionStatPayLostPackets were added, and usdL2tpSessionStatusLacTunneledIfIndex replaced usdL2tpSessionStatusLacPppIfIndex. | ||
| usdL2tpCompliance2 | 1.3.6.1.4.1.4874.2.2.35.3.2.2 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when a new object was added to the configuration group. | ||
| usdL2tpCompliance3 | 1.3.6.1.4.1.4874.2.2.35.3.2.3 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when a new objects were added to the configuration group. | ||
| usdL2tpCompliance4 | 1.3.6.1.4.1.4874.2.2.35.3.2.4 | The compliance statement for SNMPv2 entities which implement the L2TP MIB. |
RFC description
Layer Two Tunneling Protocol (L2TP) configuration and statistics for Unisphere routers.
Start monitoring Juniper/Unisphere ERX edge routing switch, LAC/LNS (L2TP tunnel/destination-count status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.