| OID symbolic | OID numeric | Type | Access | Description |
|---|
| marconi | 1.3.6.1.4.1.326 | | | |
| systems | 1.3.6.1.4.1.326.2 | | | |
| external | 1.3.6.1.4.1.326.2.20 | | | |
| dlink | 1.3.6.1.4.1.326.2.20.1 | | | |
| dlinkcommon | 1.3.6.1.4.1.326.2.20.1.1 | | | |
| golf | 1.3.6.1.4.1.326.2.20.1.2 | | | |
| golfproducts | 1.3.6.1.4.1.326.2.20.1.2.1 | | | |
| golfcommon | 1.3.6.1.4.1.326.2.20.1.2.2 | | | |
| marconi_mgmt | 1.3.6.1.4.1.326.2.20.1.2.2.2 | | | |
| es1000Series | 1.3.6.1.4.1.326.2.20.1.2.2.2.24 | | | |
| swPortTrunkPackage | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6 | | | |
| swPortTrunkTable | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1 | | not-accessible | This table specifys which ports group a set of ports(up to 8)
into a single logical link. |
| swPortTrunkEntry | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1 | | not-accessible | A list of information specifies which ports group a set of
ports(up to 8) into a single logical link. |
| INT swPortTrunkIndex | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.1 | INTEGER | read-only | The index of logical port trunk.The device max support 3 trunk groups.
The trunk group number depend on the existence of module. |
| STR swPortTrunkName | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.2 | DisplayString | read-write | The name of logical port trunk. |
| INT swPortTrunkModule | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.3 | INTEGER | read-only | Indicate which modules include in this Trunk. The value is up to 2. |
| INT swPortTrunkMasterPort | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.4 | INTEGER | read-only | The object indicates the master port number of the port trunk entry.The
first port of the trunk is implicitly configured to be the master logical
port.When using Port Trunk, you can not configure the other ports of
the group except the master port. Their configuration must be same as the
master port (e.g. speed, duplex, enabled/disabled, flow control, and so on). |
| INT swPortTrunkMemberNum | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.5 | INTEGER | read-write | Indicate how many number of ports is included in this Trunk. If
the trunk is located at expansion module (i.e. es400LinkAggrIndex
equals to 3) and the module is 100-TX or FX-MTRJ, the maximum number
of ports in the trunk is 2. The maximum number of ports is 8 for other
trunks. |
| INT swPortTrunkState | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.6.1.1.6 | INTEGER | read-write | This object decide the port trunk enabled or disabled. |
| swSnoopPackage | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7 | | | |
| swSnoopCtrlTable | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1 | | not-accessible | A list of port snooping entries.Port snooping function provide an easy
way to monitor traffic on any port. In this way any good packets appears
on the source mirror port also shows up on the target mirror port and
doesn't to reconstruct the LAN. |
| swSnoopCtrlEntry | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1.1 | | not-accessible | A list of information provide an easy way to monitor traffic on any port.
The use can bring a fancy network monitor attaching to any target mirror
port and set the port to be monitored as source mirror port. |
| INT swSnoopIndex | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1.1.1 | INTEGER | read-only | This object indicates the port snooping entry number.There is just only
one now. |
| INT swSnoopLogicSourcePort | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1.1.2 | INTEGER | read-write | This object indicates the number of port to be sniffed. The port number
is the sequential (logical) number which is also applied to bridge MIB,
etc. For instance, logical port 1~22 is mapped to module 1's 10/100Base-T
TP ports, port 23~24 is mapped to module 2's 100FX/TX ports, port 25 indicates
for module 3's Gigabit port, and so on. |
| INT swSnoopLogicTargetPort | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1.1.3 | INTEGER | read-write | This object indicates switch which port will sniff another port.
A trunk port member cannot be configured as a target Snooping port.
The port number is the sequential (logical) number which is also
applied to bridge MIB, etc. For instance, logical port 1~22 is mapped
to module 1's 10/100Base-T TP ports, port 23~24 is mapped to module
2's 100FX/TX ports, port 25 indicates for module 3's Gigabit port, and
so on. |
| INT swSnoopState | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.7.1.1.4 | INTEGER | read-write | This object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - Snoop funtion disable.
enable(3) - Snoop funtion enable and Snoop received or transmit
packet by snoop source port. |
| swIGMPPackage | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8 | | | |
| swIGMPCtrlTable | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1 | | not-accessible | The table controls the Vlan's IGMP function. Its scale depends on
current VLAN state (swVlanInfoStatus). If VLAN is disabled or
in Mac-Base mode, there is only one entry in the table, with
index 1. If VLAN is in Port-Base or 802.1q mode, the number of
entries can be up to 12, with index range from 1 to 12. |
| swIGMPCtrlEntry | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1.1 | | not-accessible | The entry in IGMP control table (swIGMPCtrlTable). The entry is
effective only when IGMP capture switch (swDevIGMPCaptureState)
is enabled. |
| INT swIGMPCtrlIndex | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1.1.1 | INTEGER | read-only | This object indicates the IGMP control entry number.Its scale depends on
current VLAN state (es400VlanInfoStatus). If VLAN is disabled or in
Mac-Base mode, there is only one entry in the table, with index 1.
If VLAN is in Port-Base or 802.1q mode, the number of entries is 12,
with index range from 1 to 12. |
| INT swIGMPCtrlVid | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1.1.2 | INTEGER | read-write | This object indicates the IGMP control entry's VLAN id. If VLAN is
disabled or in Mac-Base mode, the Vid is always 0 and cannot be changed
by management users. If VLAN is in Port-Base mode, the Vid is arranged
from 1 to 12 , fixed form. If VLAN is in 802.1q mode, the Vid setting
can vary from 1 to 4094 by management user, and the Vid in each entry
must be unique in the IGMP Control Table. |
| INT swIGMPCtrlTimer | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1.1.3 | INTEGER | read-write | The timer value for sending IGMP query packet when none
was sent by the multicast router in the LAN. The timer works
in per-VLAN basis. Our device will be activated to send the query
message if the timer is expired. Please reference RFC2236-1997.
And it recommends a default of 125 seconds. The timeout value must
be at least 30 seconds. |
| INT swIGMPCtrlState | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.1.1.4 | INTEGER | read-write | This object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry. |
| swIGMPInfoTable | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2 | | not-accessible | The table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. |
| swIGMPInfoEntry | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2.1 | | not-accessible | Information about current IGMP query information, provided that
swDevIGMPCaptureState and swIGMPCtrlState of associated VLAN
entry are all enabled. |
| INT swIGMPInfoIndex | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2.1.1 | INTEGER | read-only | This object indicates the IGMP query information entry number. It could
be up to 12 entries, depending on current number of VLAN entries. |
| INT swIGMPInfoVid | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2.1.2 | INTEGER | read-only | This object indicates the Vid of associated IGMP info table entry. It
follows swIGMPCtrlVid in the associated entry of IGMP control table
(swIGMPCtrlTable). |
| INT swIGMPInfoQueryCount | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2.1.3 | INTEGER | read-only | This object indicates the number of query packets received since the
IGMP function enabled, in per-VLAN basis. |
| INT swIGMPInfoTxQueryCount | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.2.1.4 | INTEGER | read-only | This object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and increment
this object by 1. |
| swIGMPTable | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3 | | not-accessible | The table containing current IGMP information which captured by this
device, provided that swDevIGMPCaptureState and swIGMPCtrlState of
associated VLAN entry are all enabled. Note that the priority
of IGMP table entries is lower than Filtering Table, i.e. if there is a
table hash collision between the entries of IGMP Table and Filtering Table
inside the switch H/W address table, then Filtering Table entry overwrite
the colliding entry of IGMP Table. See swFdbFilterTable description also. |
| swIGMPEntry | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1 | | not-accessible | Information about current IGMP information which captured by this
device , provided that swDevIGMPCaptureState and swIGMPCtrlState of
associated VLAN entry are all enabled. |
| INT swIGMPVid | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1.1 | INTEGER | read-only | This object indicates the Vid of individual IGMP table entry. It
shows the Vid of IGMP report information captured on network. |
| IP swIGMPGroupIpAddr | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1.2 | IpAddress | read-only | This object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis. |
| MAC swIGMPMacAddr | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1.3 | MacAddress | read-only | This object is identify mac address which is corresponding
to swIGMPGroupIpAddr, in per-Vlan basis.. |
| POR swIGMPPortMap | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1.4 | PortList | read-only | This object indicates which ports are belong to the same multicast
group, in per-Vlan basis. Each multicast group has a octect string
to indicate with port map. The most significant bit represents the
lowest numbered port, and the least significant bit represents the
highest numbered port. In module 1 (base module), there are 22 100M
twisted-pair ports (port 1..22) which is mapped to the PortMap's
port 1 to 22 respectively. In module 2 (slot 1 module), there are 2
100M FX/100 TX (or a single port 100M FX) ports which is mapped to
the PortMap's port 23,24 respectively (if the module is a single port
100M FX, it is just mapped to port 23 and port 24 is ignored). Module
3 (slot 2 module) is a single-port Gigabit Ethernet and it is mapped
to the PortMap's port 25. |
| INT swIGMPIpGroupReportCount | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.8.3.1.5 | INTEGER | read-only | This object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis. . |
| INT endOfMIB | 1.3.6.1.4.1.326.2.20.1.2.2.2.24.9999 | INTEGER | read-only | |
