| OID symbolic | OID numeric | Type | Access | Description |
|---|
| usdDs1MIB | 1.3.6.1.4.1.4874.2.2.5 | | | The DS1/E1 MIB for the Unisphere enterprise. This MIB contains managed
objects to supplement those found in RFC1406 DS1/E1 MIB. |
| usdDs1Objects | 1.3.6.1.4.1.4874.2.2.5.1 | | | |
| usdDsx1ConfigTable | 1.3.6.1.4.1.4874.2.2.5.1.1 | | not-accessible | This table contains entries for DS1/E1 interfaces present in the
system. |
| usdDsx1ConfigEntry | 1.3.6.1.4.1.4874.2.2.5.1.1.1 | | not-accessible | Each entry describes the characteristics of an DS1/E1 interface. |
| USD usdDsx1TimeSlotMap | 1.3.6.1.4.1.4874.2.2.5.1.1.1.1 | UsdTimeSlotMap | read-only | A bitmap representing the timeslots on the DS1/E1 interface that have
been allocated for service.
For channelized DS1/E1, set bits reflect the union of timeslot
allocations across all fractional arrangements operating over this
DS1/E1 interface.
For unchannelized DS1/E1, all relevant timeslot bits will be set. |
| I32 usdDsx1Ds1ChannelNumber | 1.3.6.1.4.1.4874.2.2.5.1.1.1.2 | Integer32 | read-create | This variable represents the channel number of the DS1/E1 on its parent
DS3/E3. A value of 0 indicates this DS1/E1 does not have a parent
DS3/E3. |
| I32 usdDsx1Capabilities | 1.3.6.1.4.1.4874.2.2.5.1.1.1.3 | Integer32 | read-only | A value which indicates the set of capabilities of the DS1/E1
interface.
The value is a sum. This sum initially takes the value zero. Then, for
each capability, C, in the range 1 through 3, that this interface
supports, 2 raised to (C - 1) is added to the sum. For example, an
interface which is only E1 capable would have a value of 2 (2^(2-1)).
In contrast, an interface which is both T1 and J1 capable would have a
value of 5 (2^(1-1) + 2^(3-1)). The values for DS1/E1 interface
capabilities are as follows:
capability function
1 T1
2 E1
3 J1 |
| INT usdDsx1Mode | 1.3.6.1.4.1.4874.2.2.5.1.1.1.4 | INTEGER | read-create | This variable represents the DS1/E1 interface mode. The value of the
usdDsx1Capabilities object for the DS1/E1 interface indicates the valid
set of values for this object. |
| I32 usdDsx1LineBuildOutCapabilities | 1.3.6.1.4.1.4874.2.2.5.1.1.1.5 | Integer32 | read-only | A value which indicates the set of line build out capabilities of the
DS1/E1 interface.
The value is a sum. This sum initially takes the value zero. Then, for
each line build out capability, C, in the range 1 or 2, that this
interface supports, 2 raised to (C - 1) is added to the sum. For
example, an interface which is only short haul capable would have a
value of 2 (2^(2-1)). In contrast, an interface which is both short
haul and long haul capable would have a value of 3 (2^(1-1) + 2^(2-1)).
The values for DS1/E1 interface line build out capabilities are as
follows:
line build out capability function
1 short haul
2 long haul |
| INT usdDsx1LineBuildOutType | 1.3.6.1.4.1.4874.2.2.5.1.1.1.6 | INTEGER | read-create | This variable represents the configured line build out type of the
DS1/E1 interface. The value of the usdDsx1LineBuildOutCapabilities
object for the DS1/E1 interface indicates the valid set of values for
this object. |
| INT usdDsx1LineAttenuation | 1.3.6.1.4.1.4874.2.2.5.1.1.1.7 | INTEGER | read-create | This variable represents the configured line attenuation of the DS1/E1
interface. Note that the value of this object only takes effect when
the value of the usdDsx1LineBuildOutType for the DS1/E1 interface is set
to longHaul(2). |
| I32 usdDsx1LineLength | 1.3.6.1.4.1.4874.2.2.5.1.1.1.8 | Integer32 | read-create | This variable represents the length of the DS1/E1 line in meters. Note
that the value of this object only takes effect when the value of the
usdDsx1LineBuildOutType for the DS1/E1 interface is set to
shortHaul(1). |
| NUM usdDsx1LowerIfIndex | 1.3.6.1.4.1.4874.2.2.5.1.1.1.9 | InterfaceIndexOrZero | read-create | The ifIndex of the interface over which this Dsx1 interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a nonzero value be configured at entry creation. |
| ROW usdDsx1RowStatus | 1.3.6.1.4.1.4874.2.2.5.1.1.1.10 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdDsx1RowStatus
usdDsx1LowerIfIndex
In addition, when creating an entry the following conditions must hold:
A value for ifIndex must have been determined previously, by reading
usdDsx1NextIfIndex.
The interface identified by usdDsx1hLowerIfIndex must exist.
A corresponding entry in ifTable/ifXTable/usdIfTable is created/destroyed
as a result of creating/destroying an entry in this table. |
| INT usdDsx1SendCode | 1.3.6.1.4.1.4874.2.2.5.1.1.1.11 | INTEGER | read-create | This variable indicates what type of code is being sent across the DS1
interface by the device. |
| INT usdDsx1YellowAlarm | 1.3.6.1.4.1.4874.2.2.5.1.1.1.12 | INTEGER | read-create | This bitmap indicates the yellow alarm settings, and is the sum of the
capabilities. |
| INT usdDsx1RemoteLoopback | 1.3.6.1.4.1.4874.2.2.5.1.1.1.13 | INTEGER | read-create | This variable indicates the remote loopback setting. |
| INT usdDsx1FdlCarrier | 1.3.6.1.4.1.4874.2.2.5.1.1.1.14 | INTEGER | read-create | Specifies the interface is used in carrier environment. |
| STR usdDsx1FdlEic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.15 | DisplayString | read-create | This is the equipment identification code. |
| STR usdDsx1FdlLic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.16 | DisplayString | read-create | This is the location identification code. |
| STR usdDsx1FdlFic | 1.3.6.1.4.1.4874.2.2.5.1.1.1.17 | DisplayString | read-create | This is the frame identification code. |
| STR usdDsx1FdlUnit | 1.3.6.1.4.1.4874.2.2.5.1.1.1.18 | DisplayString | read-create | This is the unit identification code. |
| STR usdDsx1FdlPfi | 1.3.6.1.4.1.4874.2.2.5.1.1.1.19 | DisplayString | read-create | This is the facility identification code. |
| STR usdDsx1FdlPort | 1.3.6.1.4.1.4874.2.2.5.1.1.1.20 | DisplayString | read-create | This is the equipment port number. |
| STR usdDsx1FdlGenerator | 1.3.6.1.4.1.4874.2.2.5.1.1.1.21 | DisplayString | read-create | This is the generator number. |
| USD usdDs1NextIfIndex | 1.3.6.1.4.1.4874.2.2.5.1.2 | UsdNextIfIndex | read-only | Coordinate ifIndex value allocation for entries in usdDsx1ConfigTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously. |
| usdDs1Conformance | 1.3.6.1.4.1.4874.2.2.5.4 | | | |
| usdDs1Compliances | 1.3.6.1.4.1.4874.2.2.5.4.1 | | | |
| usdDs1Compliance | 1.3.6.1.4.1.4874.2.2.5.4.1.1 | | | Obsolete compliance statement for entities which implement the
Unisphere DS1/E1 MIB. This statement became obsolete when new objects
were added. |
| usdDs1Compliance1 | 1.3.6.1.4.1.4874.2.2.5.4.1.2 | | | Obsolete compliance statement for entities which implement the
Unisphere DS1/E1 MIB. This statement became obsolete when dynamic DS1
interface support was added. |
| usdDs1Compliance2 | 1.3.6.1.4.1.4874.2.2.5.4.1.3 | | | Obsolete compliance statement for entities which implement the
Unisphere DS1/E1 MIB. This statement became obsolete when FDL support
was added. |
| usdDs1Compliance3 | 1.3.6.1.4.1.4874.2.2.5.4.1.4 | | | The compliance statement for entities which implement the Unisphere
DS1/E1 MIB. |
| usdDs1Groups | 1.3.6.1.4.1.4874.2.2.5.4.2 | | | |
| usdDs1Group | 1.3.6.1.4.1.4874.2.2.5.4.2.1 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Unisphere product. This group became obsolete when new
objects where added to the MIB. |
| usdDs1Group1 | 1.3.6.1.4.1.4874.2.2.5.4.2.2 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Unisphere product. This group became obsolete when
dynamic DS1 interface support was added. |
| usdDs1Group2 | 1.3.6.1.4.1.4874.2.2.5.4.2.3 | | | Obsolete collection of objects providing management of DS1/E1
interfaces in a Unisphere product. This group became obsolete when FDL
support was added. |
| usdDs1Group3 | 1.3.6.1.4.1.4874.2.2.5.4.2.4 | | | A collection of objects providing management of DS1/E1 interfaces in a
Unisphere product. |
