UBQS-SLD-MIB

All MIBs › UBQS-SLD-MIB

Organization: Ubiquoss Corp.

Last Updated: 2011-07-19

Description: MIB for detecting and reporting self-loop (switching loop) conditions on individual interfaces of Ubiquoss network switches

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is UBQS-SLD-MIB?

UBQS-SLD-MIB is a Ubiquoss Corp. proprietary MIB implementing SLD (Self Loop Detect), which identifies and disables a port looped back on itself. Its objects cover a state-change notification, global enable/hello-interval/recovery-time/notify-only/port-check/interface-state-change-enable flags, and a per-interface table (enable, hello interval, recovery time, notify-only, port-check, state, recovery method, last-state-change time, error-disabled count, state-reset action). As a configuration/notification MIB it lets an administrator confirm which ports are error-disabled due to a detected self-loop, and their auto-recovery settings, on a Ubiquoss switch. It is deployed on Ubiquoss Corp. switching equipment (self loop detection). Engineers can download the UBQS-SLD-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in UBQS-SLD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ubiquoss Corp. switching equipment (self loop detection)

Monitoring Examples

An administrator receives ubiSelfLoopDetectStateChange and checks ubiSldIfErrorDisabledCount to confirm a self-loop was detected and disabled on a Ubiquoss switch port.

What Can Be Monitored

self-loop detection state and error-disable/recovery status

Imported Objects

From IF-MIB

ifAdminStatus	OBJECT-TYPE
ifIndex	OBJECT-TYPE
ifName	OBJECT-TYPE
ifOperStatus	OBJECT-TYPE
ifType	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From UBQS-SMI

ubiMgmtv2

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
ubiSldMIB	1.3.6.1.4.1.7800.100.25			The UBQS-SLD-MIB is used for getting the information about self loop detect(SLD).
ubiSldMIBNotificationPrefix	1.3.6.1.4.1.7800.100.25.0
NTF ubiSelfLoopDetectStateChange	1.3.6.1.4.1.7800.100.25.0.1			When SLD status is changed, this notification is occured.
ubiSldMIBObjects	1.3.6.1.4.1.7800.100.25.1
ubiSldGlobal	1.3.6.1.4.1.7800.100.25.1.1
T/F ubiSldEnabled	1.3.6.1.4.1.7800.100.25.1.1.1	TruthValue	read-write	It is enable function of SLD.
I32 ubiSldHelloInterval	1.3.6.1.4.1.7800.100.25.1.1.2	Integer32	read-write	Global SLD hello interval.
INT ubiSldRecoveryTime	1.3.6.1.4.1.7800.100.25.1.1.3	INTEGER	read-write	Global SLD Recovery time.
T/F ubiSldNotifyOnlyEnbaled	1.3.6.1.4.1.7800.100.25.1.1.4	TruthValue	read-write	It is enable Global function of only notification without SLD.
T/F ubiSldPortCheckEnabled	1.3.6.1.4.1.7800.100.25.1.1.5	TruthValue	read-write	It is enable global configuration of SLD without checking port.
T/F ubiSldIfStateChangeEnabled	1.3.6.1.4.1.7800.100.25.1.1.6	TruthValue	read-write	It is enable to sending SLD SNMP trap message
ubiSldIfTable	1.3.6.1.4.1.7800.100.25.1.2		not-accessible
ubiSldIfEntry	1.3.6.1.4.1.7800.100.25.1.2.1		not-accessible
T/F ubiSldIfEnabled	1.3.6.1.4.1.7800.100.25.1.2.1.1	TruthValue	read-write	It is enable to transmit SLD hello PDU in interface.
I32 ubiSldIfHelloInterval	1.3.6.1.4.1.7800.100.25.1.2.1.2	Integer32	read-write	It is changed SLD hello interval.
INT ubiSldIfRecoveryTime	1.3.6.1.4.1.7800.100.25.1.2.1.3	INTEGER	read-write	When it is configured, if interface is disabled by SLD, interface automatically recover after recovery time.
T/F ubiSldIfNotifyOnlyEnabled	1.3.6.1.4.1.7800.100.25.1.2.1.4	TruthValue	read-write	When it is configured, if self-loop is detected, only notification is occured without disable interface.
T/F ubiSldIfPortCheckEnabled	1.3.6.1.4.1.7800.100.25.1.2.1.5	TruthValue	read-write	When it is enabled, if it receive SLD hello PDU of anothor interface, it regards SLD.
INT ubiSldIfState	1.3.6.1.4.1.7800.100.25.1.2.1.6	INTEGER	read-only	Current interface status enable(1) : interface is active errDisable(2) : interface is disable by SLD.
INT ubiSldIfRecoveryMethod	1.3.6.1.4.1.7800.100.25.1.2.1.7	INTEGER	read-only	Last Recorvery status none(1) : none autoRecovery(2) : Auto recovery manualRecovery(3): Manual recoery
TIM ubiSldIfLastStateChangeTime	1.3.6.1.4.1.7800.100.25.1.2.1.8	TimeStamp	read-only	Last time of changing interface status by SLD.
I32 ubiSldIfErrorDisabledCount	1.3.6.1.4.1.7800.100.25.1.2.1.9	Integer32	read-only	The number of occurence self-loop detection.
INT ubiSldIfStateReset	1.3.6.1.4.1.7800.100.25.1.2.1.10	INTEGER	read-write	It manually clear interface status by SLD. none(0) : Do nothing reset(1) : Clear interface.
ubiSldMIBConformance	1.3.6.1.4.1.7800.100.25.2
ubiSldMIBCompliances	1.3.6.1.4.1.7800.100.25.2.1
ubiSldMIBGroups	1.3.6.1.4.1.7800.100.25.2.2

RFC description

Detects self-loop (SLD) conditions on network interfaces and generates notifications when loops are detected.

Start monitoring Ubiquoss Corp. switching equipment, self loop detection (error-disabled port/recovery status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download UBQS-SLD-MIB

What Is UBQS-SLD-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description