All MIBs › TN-MC-REDUNDANCY-MIB
Organization: Nokia
Last Updated: 2012-09-01
Category: Nokia Carrier Ethernet, VRRP and Redundancy
Description: Covers multi-chassis redundancy group configuration and failover state for Nokia carrier Ethernet equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TN-MC-REDUNDANCY-MIB?
TN-MC-REDUNDANCY-MIB, despite its 'TN' prefix, is a Nokia enterprise MIB (per its module description, covering the Nokia 7x50 SR system) for managing multi-chassis redundancy peer relationships used in dual-homed link-aggregation deployments. It exposes tnMcPeerTable with peer IP address, authentication key, source IP binding, and both administrative and operational states for each redundancy peer. It is used to monitor software/hardware redundancy status: a mismatch between tnMcPeerAdminState and the peer's actual operational source-IP binding (tnMcPeerSrcIpOperType/Addr) reveals a multi-chassis redundancy relationship that's configured but not functioning, putting the network at risk of a split-brain condition if the active chassis fails. It complements standard link-aggregation (LACP) concepts and sits within the broader TIMETRA/Nokia SROS enterprise MIB tree. It is deployed on Nokia SROS routers (7750 SR, 7450 ESS) configured for multi-chassis link aggregation to provide chassis-level redundancy, and engineers consult the TN-MC-REDUNDANCY-MIB MIB definition when configuring peer relationships.
IPNetwork Monitor allows you to monitor SNMP objects defined in TN-MC-REDUNDANCY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia 1830 PSS (Photonic Service Switch) optical transport platform
Monitoring Examples
An admin would poll tnMcPeerTable and compare tnMcPeerAdminState against tnMcPeerSrcIpOperAddr/Type for each peer to confirm the redundancy relationship is both configured and operationally bound. A peer whose admin state is up but whose operational source IP fails to bind would indicate a broken multi-chassis redundancy link, risking a split-brain scenario if a failover were triggered. tnMcPeerAuthKey would be checked to confirm authentication is correctly configured between peers.
What Can Be Monitored
- MC redundancy peer IP address
- peer admin state
- authentication key configuration
- source IP operational address/type
- peer row status
This MIB depends on
Related MIBs
Imported Objects
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressPrefixLength | |
| InetAddressType |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeInterval | |
| TimeStamp | |
| TruthValue |
From TN-LAG-MIB
| LAGInterfaceNumber |
From TN-SAP-MIB
| tnSapEncapValue | OBJECT-TYPE |
| tnSapPortId | OBJECT-TYPE |
From TN-SERV-MIB
| tnSvcId | OBJECT-TYPE |
From TN-TC-MIB
| TItemDescription | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TmnxAdminState | |
| TmnxEnabledDisabled | |
| TmnxEncapVal | |
| TmnxOperState | |
| TmnxPortID | |
| TmnxServId | |
| TmnxVRtrID |
From TROPIC-GLOBAL-REG
| tnSRMIBModules | OBJECT-IDENTITY |
| tnSRNotifyPrefix | OBJECT-IDENTITY |
| tnSRObjs | OBJECT-IDENTITY |
From TROPIC-SYSTEM-MIB
| tnSysSwitchId | OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using tnMcPeerSyncNumEntries OID:
Select a Nokia SROS routers (7750 SR, 7450 ESS) configured for multi-chassis redundancy (peer admin/oper status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tnMcPeerSyncNumEntries into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of tnMcPeerSyncNumEntries indicates the total number of entries in the MCS database per multi-chassis peer. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tnMcRedundancyMIBModule | 1.3.6.1.4.1.7483.5.1.3.40 | This document is the SNMP MIB module to manage and provision the various services of the Nokia 7x50 SR system. Copyright 2003-2011 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tnMcRedundancy | 1.3.6.1.4.1.7483.6.1.2.40 | |||
| tnMcRedundancyObjs | 1.3.6.1.4.1.7483.6.1.2.40.1 | |||
| tnMcPeerTable | 1.3.6.1.4.1.7483.6.1.2.40.1.1 | not-accessible | The tnMcPeerTable has an entry for each multi-chassis peer configured on this system. | |
| tnMcPeerEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1 | not-accessible | Each row entry represents a particular multi-chassis peer. Entries are create/deleted by the user. | |
| IPt tnMcPeerIpType | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.1 | InetAddressType | not-accessible | The value of tnMcPeerIpType indicates the address type of tnMcPeerIpAddr. |
| IP tnMcPeerIpAddr | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.2 | InetAddress | not-accessible | The value of tnMcPeerIpAddr indicates the address of the multi-chassis peer. Its type is specified by tnMcPeerIpType. It must be a valid unicast address. |
| ROW tnMcPeerRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.3 | RowStatus | read-create | The value of tnMcPeerRowStatus is used for creation/deletion of multi-chassis peers. |
| TIT tnMcPeerDescription | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.4 | TItemDescription | read-create | The value of tnMcPeerDescription specifies the textual description of this multi-chassis peer. |
| OCT tnMcPeerAuthKey | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.5 | OCTET STRING | read-create | The value of tnMcPeerAuthKey specifies the authentication key used between this node and the multi-chassis peer. The authentication key can be any combination of letters or numbers. This object will always return an empty string on a read. |
| IPt tnMcPeerSrcIpType | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.6 | InetAddressType | read-create | The value of tnMcPeerSrcIpType specifies the address type of tnMcPeerSrcIpAddr. |
| IP tnMcPeerSrcIpAddr | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.7 | InetAddress | read-create | The value of tnMcPeerSrcIpAddr specifies the source address used to communicate with the multi-chassis peer. Its type is specified by tnMcPeerSrcIpType. It must be a valid unicast address. |
| TMN tnMcPeerAdminState | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.8 | TmnxAdminState | read-create | The value of tnMcPeerAdminState specifies the administrative state of this multi-chassis peer. |
| IPt tnMcPeerSrcIpOperType | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.9 | InetAddressType | read-only | The value of tnMcPeerSrcIpOperType indicates the operational source address type of tnMcPeerSrcIpOperAddr, the multi-chassis peer source IP address. |
| IP tnMcPeerSrcIpOperAddr | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.10 | InetAddress | read-only | The value of tnMcPeerSrcIpOperAddr indicates the operational source address in use to communicate with the multi-chassis peer. Its type is specified by tnMcPeerSrcIpOperType. |
| TMN tnMcPeerRingsOperState | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.11 | TmnxOperState | read-only | The value of tnMcPeerRingsOperState indicates the operational state of this multi-chassis peer with respect to multi-chassis ring operation. If there are no entries in the tnMcRingTable associated with this peer, the value of tnMcPeerRingsOperState is 'unknown'. |
| TNA tnMcPeerName | 1.3.6.1.4.1.7483.6.1.2.40.1.1.1.12 | TNamedItemOrEmpty | read-create | The value of tnMcPeerName specifies the name of this multi-chassis peer. |
| tnMcPeerSyncTable | 1.3.6.1.4.1.7483.6.1.2.40.1.2 | not-accessible | The tnMcPeerSyncTable has an entry for each multi-chassis peer synchronization protocol. | |
| tnMcPeerSyncEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1 | not-accessible | Each row entry represents a particular multi-chassis peer synchronization protocol. Entries are create/deleted by the user. | |
| ROW tnMcPeerSyncRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.1 | RowStatus | read-create | The value of tnMcPeerSyncRowStatus is used for creation and deletion of a synchronization protocol with a multi-chassis peer. |
| T/F tnMcPeerSyncIgmp | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.2 | TruthValue | read-create | The value of tnMcPeerSyncIgmp specifies whether IGMP protocol information should be synchronized with the multi-chassis peer. |
| T/F tnMcPeerSyncIgmpSnooping | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.3 | TruthValue | read-create | The value of tnMcPeerSyncIgmpSnooping specifies whether IGMP-snooping information should be synchronized with the multi-chassis peer. |
| T/F tnMcPeerSyncSubMgmt | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.4 | TruthValue | read-create | The value of tnMcPeerSyncSubMgmt specifies whether subscriber management IPoE information should be synchronized with the multi-chassis peer. |
| T/F tnMcPeerSyncSrrp | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.5 | TruthValue | read-create | The value of tnMcPeerSyncSrrp specifies whether SRRP information should be synchronized with the multi-chassis peer. |
| TMN tnMcPeerSyncAdminState | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.6 | TmnxAdminState | read-create | The value of tnMcPeerSyncAdminState specifies the administrative status of the synchronization protocol with the multi-chassis peer. |
| TMN tnMcPeerSyncOperState | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.7 | TmnxOperState | read-only | The value of tnMcPeerSyncOperState indicates the operational status of the synchronization protocol with the multi-chassis peer. |
| BIT tnMcPeerSyncOperFlags | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.8 | Bits | read-only | The value of tnMcPeerSyncOperFlags indicates the reason that the synchronization protocol with the multi-chassis peer is down. syncAdminDown(0) Synchronization is administratively down. No recovery needed. peerAdminDown(1) The peering is administratively down. No recovery needed. connectionDown(2) There is a problem with the connection to the multi-chassis peer. The connection will be automatically repaired. No recovery needed internalError(3) There has been an irrecoverable internal error. The synchronization protocol cannot come up again without user intervention. The user must set the tnMcPeerSyncAdminState to 'outOfService', then 'inService'. mcsVersionMismatch(4) There is a mismatch between the versions of the multi-chassis sync protocol running on each peer. platformMismatch(5) There is a mismatch between the platforms of each peer the multi-chassis sync protocol is running on. appVersionMismatch(6) There is a mismatch between the versions of applications attempting to use the multi-chassis sync protocol on the two peers. appSupportMismatch(7) There is a mismatch between the applications supported by the multi-chassis sync protocol on each peer. |
| INT tnMcPeerSyncStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.9 | INTEGER | read-only | The value of tnMcPeerSyncStatus indicates the status of the synchronization process. |
| TIM tnMcPeerSyncLastSyncTime | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.10 | TimeStamp | read-only | The value of tnMcPeerSyncLastSyncTime indicates the sysUpTime at the time the last synchronization with the peer was successful. |
| C32 tnMcPeerSyncNumEntriesEx | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.11 | Counter32 | read-only | The value of tnMcPeerSyncNumEntries indicates the total number of entries in the MCS database per multi-chassis peer. |
| C32 tnMcPeerSyncLclDeletedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.12 | Counter32 | read-only | The value of tnMcPeerSyncLclDeletedEntries indicates the number of locally deleted entries in the MCS database per multi-chassis peer. Locally deleted entries are entries that are not being used by the local MCS client application. |
| C32 tnMcPeerSyncAlarmedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.13 | Counter32 | read-only | The value of tnMcPeerSyncAlarmedEntries indicates the number of alarmed entries in the MCS database per multi-chassis peer. Entries with an alarm are entries that are not being used by the local client application due to resource constraints. |
| C32 tnMcPeerSyncRemNumEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.14 | Counter32 | read-only | The value of tnMcPeerSyncRemNumEntries indicates the total number of entries in the MCS database of the multi-chassis peer. |
| C32 tnMcPeerSyncRemLclDelEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.15 | Counter32 | read-only | The value of tnMcPeerSyncRemLclDelEntries indicates the number of locally deleted entries in the MCS database of the multi-chassis peer. Locally deleted entries are entries that are not being used by the remote MCS client application. |
| C32 tnMcPeerSyncRemAlarmedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.2.1.16 | Counter32 | read-only | The value of tnMcPeerSyncRemAlarmedEntries indicates the number of alarmed entries in the MCS database of the multi-chassis peer. Entries with an alarm are entries that are not being used by the remote client application due to resource constraints. |
| tnMcPeerSyncPortTable | 1.3.6.1.4.1.7483.6.1.2.40.1.3 | not-accessible | The tnMcPeerSyncPortTable has an entry for each port that is being synchronized with a multi-chassis peer. | |
| tnMcPeerSyncPortEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.3.1 | not-accessible | Each row entry represents a port to be synchronized. Entries are created/deleted by the user. | |
| TMN tnMcPeerSyncPortId | 1.3.6.1.4.1.7483.6.1.2.40.1.3.1.1 | TmnxPortID | not-accessible | The value of tnMcPeerSyncPortId indicates the port to be synchronized with the multi-chassis peer. |
| ROW tnMcPeerSyncPortRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.3.1.2 | RowStatus | read-create | The value of tnMcPeerSyncPortRowStatus is used for creation and deletion of ports to be synchronized with the multi-chassis peer. |
| TNA tnMcPeerSyncPortSyncTag | 1.3.6.1.4.1.7483.6.1.2.40.1.3.1.3 | TNamedItemOrEmpty | read-create | The value of tnMcPeerSyncPortSyncTag specifies a synchronization tag to be used while synchronizing this port with the multi-chassis peer. |
| tnMcPeerSyncPortEncapRangeTable | 1.3.6.1.4.1.7483.6.1.2.40.1.4 | not-accessible | The tnMcPeerSyncPortEncapRangeTable has an entry for each port encapsulation value range to be synchronized with a multi-chassis peer. | |
| tnMcPeerSyncPortEncapRangeEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1 | not-accessible | Each row entry represents a range of encapsulation values on a port to be synchronized with a multi-chassis peer. Entries are created/deleted by the user. | |
| INT tnMcPeerSyncPortEncapType | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1.1 | INTEGER | not-accessible | The value of tnMcPeerSyncPortEncapType indicates the encapsulation type used to interpret tnMcPeerSyncPortEncapMin and tnMcPeerSyncPortEncapMax. |
| TMN tnMcPeerSyncPortEncapMin | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1.2 | TmnxEncapVal | not-accessible | The value of tnMcPeerSyncPortEncapMin indicates the minimum encapsulation value on the port indicated by tnMcPeerSyncPortId that will be synchronized with the multi-chassis peer. |
| TMN tnMcPeerSyncPortEncapMax | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1.3 | TmnxEncapVal | not-accessible | The value of tnMcPeerSyncPortEncapMax indicates the maximum encapsulation value on the port indicated by tnMcPeerSyncPortId that will be synchronized with the multi-chassis peer. |
| ROW tnMcPeerSyncPortEncapRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1.4 | RowStatus | read-create | The value of tnMcPeerSyncPortEncapRowStatus is used for creation and deletion of encapsulation value ranges over a specific port to be synchronized with the multi-chassis peer. |
| TNA tnMcPeerSyncPortEncapSyncTag | 1.3.6.1.4.1.7483.6.1.2.40.1.4.1.5 | TNamedItem | read-create | The value of tnMcPeerSyncPortEncapSyncTag specifies a synchronization tag to be used while synchronizing this encapsulation value range with the multi-chassis peer. This object MUST be specified at row creation time. |
| TIM tnMcLagConfigTableLastChanged | 1.3.6.1.4.1.7483.6.1.2.40.1.5 | TimeStamp | read-only | The value of tnMcLagConfigTableLastChanged indicates the sysUpTime at the time of the last modification of an entry in the tnMcLagConfigTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| tnMcLagConfigTable | 1.3.6.1.4.1.7483.6.1.2.40.1.6 | not-accessible | The tnMcLagConfigTable has an entry for each multi-chassis LAG configuration for the indicated peer. | |
| tnMcLagConfigEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1 | not-accessible | Each row entry represents configuration data for a multi-chassis LAG configuration with a given peer. Rows are created or removed automatically by the system, each time a row is created or deleted in the tnMcPeerTable. | |
| TIM tnMcLagConfigPeerLastChanged | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.1 | TimeStamp | read-only | The value of tnMcLagConfigPeerLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TMN tnMcLagConfigPeerAdminstate | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.2 | TmnxAdminState | read-write | The value of tnMcLagConfigPeerAdminstate specifies the administrative state of the multi-chassis lag with the indicated peer. |
| U32 tnMcLagConfigKeepALiveIvl | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.3 | Unsigned32 | read-write | The value of tnMcLagConfigKeepALiveIvl specifies the mc-lag keepalive timer value in units of 0.1 sec. This defines the interval at which keep-alive messages are exchanged between two systems participating in mc-lag. These keep-alive messages are used to determine remote-node failure. |
| U32 tnMcLagConfigHoldOnNgbrFailure | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.4 | Unsigned32 | read-write | The value of tnMcLagConfigHoldOnNgbrFailure specifies how many tnMcLagConfigKeepALiveIvl intervals the standby node will wait for packets from the active node before assuming a redundant-neighbor node failure. This delay in switch-over operation is required to accommodate for different factors influencing node failure detection rate, such as IGP convergence, or HA switch-over times and to prevent that the standby node takes actions prematurely. |
| INT tnMcLagConfigOperState | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.5 | INTEGER | read-only | The value of tnMcLagConfigOperState indicates the operational status of this multi-chassis LAG peer. |
| TIM tnMcLagConfigPeerLastStateChge | 1.3.6.1.4.1.7483.6.1.2.40.1.6.1.6 | TimeStamp | read-only | The value of tnMcLagConfigPeerLastStateChge indicates the sysUpTime at the time of the last operational state change for this multi-chassis LAG peer. If no changes were made since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| TIM tnMcLagConfigLagTableLastChanged | 1.3.6.1.4.1.7483.6.1.2.40.1.7 | TimeStamp | read-only | The value of tnMcLagConfigLagTableLastChanged indicates the sysUpTime at the time of the last modification of an entry in the tnMcLagConfigLagTable. If no changes were made to the table since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| tnMcLagConfigLagTable | 1.3.6.1.4.1.7483.6.1.2.40.1.8 | not-accessible | The tnMcLagConfigLagTable has an entry for each lag that participates in a multi-chassis configuration for the indicated peer. | |
| tnMcLagConfigLagEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1 | not-accessible | Each row entry represents configuration data for a lag that participates in a multi-chassis configuration with a given peer. Rows can be created and deleted by the operator. | |
| NUM tnMcLagConfigLagId | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.1 | LAGInterfaceNumber | not-accessible | The value of tnMcLagConfigLagId identifies the Link Aggregation Group on this system that is to form a mc-lag configuration with the indicated peer. |
| TIM tnMcLagConfigLagLastChanged | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.2 | TimeStamp | read-only | The value of tnMcLagConfigLagLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| ROW tnMcLagConfigLagRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.3 | RowStatus | read-create | The value of tnMcLagConfigLagRowStatus specifies the row status of this row. |
| U32 tnMcLagConfigLaglacpKey | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.4 | Unsigned32 | read-create | The value of tnMcLagConfigLaglacpKey specifies a 16bit key that needs to be configured in the same manner on both sides of the mc-lag in order for the mc-lag to come up. The value of tnMcLagConfigLaglacpKey must be 0 when the value of tLagStandbySignaling of the corresponding LAG is 'powerOff (2)'. The value of tnMcLagConfigLaglacpKey cannot be 0 when the value of tLagStandbySignaling of the corresponding LAG is 'lacp (1)'. |
| OCT tnMcLagConfigLagSystemId | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.5 | OCTET STRING | read-create | The value of tnMcLagConfigLagSystemId specifies the system-id to be used in the context of mc-lag operation. The partner system will consider all ports using the same system-id, system priority and lacp-key as part of the same lag. In order to achieve this in mc-lag operation, both systems have to be configured with the same values. As long as the system does not have the connection with its redundant peer, it will use the locally defined value (chassis MAC address). After detecting a redundant node failure, the previously active system will keep on using the system-id configured here, while the standby system will switch to its locally defined value. The value of this object must be all zeroes when the value of tLagStandbySignaling of the corresponding LAG is 'powerOff (2)'. The value of this object cannot be all zeroes when the value of tLagStandbySignaling of the corresponding LAG is 'lacp (1)'. |
| U32 tnMcLagConfigLagSystemPriority | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.6 | Unsigned32 | read-create | The value of tnMcLagConfigLagSystemPriority specifies the system priority to be used in the context of mc-lag. The partner system will consider all ports using the same system-id, system priority and lacp-key as part of the same lag. In order to achieve this in mc-lag operation, both systems have to be configured with the same values. A low numeric value specifies a high system priority. The value of this object must be 0 when the value of tLagStandbySignaling of the corresponding LAG is 'powerOff (2)'. The value of this object cannot be 0 when the value of tLagStandbySignaling of the corresponding LAG is 'lacp (1)'. |
| NUM tnMcLagConfigLagRemoteLagId | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.7 | LAGInterfaceNumber | read-create | The value of tnMcLagConfigLagRemoteLagId specifies the Lag ID on the remote system. If not specified, the value of this object will be set to the value of tnMcLagConfigLagId. |
| U32 tnMcLagConfigLagSrcBMacLSB | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.8 | Unsigned32 | read-create | The value of tnMcLagConfigLagSrcBMacLSB specifies the value of last 16-bits of the MAC address used for all the traffic ingressing the MC-Lag links. The value '4294967295' indicates use of the lacp-key as source backbone MAC address LSB. |
| U32 tnMcLagConfigLagOperSrcBMacLSB | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.9 | Unsigned32 | read-only | The value of tnMcLagConfigLagOperSrcBMacLSB indicates the operational value of last 16-bits of the MAC address used for all the traffic ingressing the MC-Lag links. |
| TMN tnMcLagConfigLagFlushEthRingOnActive | 1.3.6.1.4.1.7483.6.1.2.40.1.8.1.10 | TmnxEnabledDisabled | read-create | The value of tnMcLagConfigLagFlushEthRingOnActive specifies whether or not to flush the ethernet rings to which the services that the LAG is part of are attached. |
| tnMcLagInfoLagTable | 1.3.6.1.4.1.7483.6.1.2.40.1.10 | not-accessible | The tnMcLagInfoLagTable has an entry for each lag that participates in a multi-chassis configuration for the indicated peer. | |
| tnMcLagInfoLagEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1 | not-accessible | Each row entry represents operational data for a lag that participates in a multi-chassis configuration with a given peer. Rows are created or removed automatically by the system, each time a row is created or deleted in the tnMcLagConfigLagTable. | |
| T/F tnMcLagActiveStandby | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.1 | TruthValue | read-only | The value of tnMcLagActiveStandby indicates whether this mc-lag is active or standby. If the value of this object is 'true', this mc-lag is active. |
| T/F tnMcLagLacpIdInUse | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.2 | TruthValue | read-only | The value of tnMcLagLacpIdInUse indicates whether or not the mc-lag values (i.e. system-id, system priority and lacp-key) are advertised to the Lacp peer. If the value of this object is 'true', the mc-lag values are advertised. Otherwise the normal lag values are advertised. |
| T/F tnMcLagExtendedTimeOut | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.3 | TruthValue | read-only | The value of tnMcLagExtendedTimeOut indicates whether or not the system is using the value of tnMcLagConfigHoldOnNgbrFailure. If this is 'true', the system is temporarily using a larger value than the value configured in tnMcLagConfigHoldOnNgbrFailure. |
| STR tnMcLagSelectionLogic | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.4 | DisplayString | read-only | The value of tnMcLagSelectionLogic is a printable character string which contains information about the multi-chassis selection logic. |
| STR tnMcLagConfigMismatchString | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.5 | DisplayString | read-only | The value of tnMcLagConfigMismatchString is a printable character string which contains information about the multi-chassis configuration mismatch. |
| BIT tnMcLagConfigMismatchFlags | 1.3.6.1.4.1.7483.6.1.2.40.1.10.1.6 | Bits | read-only | The value of tnMcLagConfigMismatchFlags indicates the operational status of the multi-chassis configuration. lagIsNotMultiChassis(0) The lag is not multi-chassis on the peer. localRemoteLagIdMismatch(1) Local - remote Lag ID mismatch with the peer. lagSelectionCriteriaMismatch(2) LAG selection criteria mismatch with the peer. lagEncapsulationMismatch(3) LAG Encapsulation mismatch with the peer. mcLacpkeyMismatch(4) MC lacp-key mismatch with the peer. mcSystemPriorityMismatch(5) MC system-priority mismatch with the peer. mcSystemIdMismatch(6) MC system-id mismatch with the peer. |
| tnMcsClientAppTable | 1.3.6.1.4.1.7483.6.1.2.40.1.11 | not-accessible | The tnMcsClientAppTable has an entry for each application using the multi-chassis peer synchronization protocol configured on this system. | |
| tnMcsClientAppEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1 | not-accessible | Each row entry represents a particular multi-chassis peer synchronization protocol application. Entries cannot be created and deleted via SNMP SET operations. | |
| TMN tnMcsClientApplication | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.1 | TmnxMcsClientApp | not-accessible | The value of tnMcsClientApplication indicates the type of application using multi-chassis synchronization. |
| C32 tnMcsClientNumEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.2 | Counter32 | read-only | The value of tnMcsClientNumEntries indicates the total number of entries in the MCS database per multi-chassis peer for a particular application. |
| C32 tnMcsClientLclDeletedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.3 | Counter32 | read-only | The value of tnMcsClientLclDeletedEntries indicates the number of locally deleted entries in the MCS database per multi-chassis peer for a particular application. Locally deleted entries are entries that are not being used by the local MCS client application. |
| C32 tnMcsClientAlarmedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.4 | Counter32 | read-only | The value of tnMcsClientAlarmedEntries indicates the number of alarmed entries in the MCS database per multi-chassis peer for a particular application. Entries with an alarm are entries that are not being used by the local client application due to resource constraints. |
| C32 tnMcsClientRemNumEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.5 | Counter32 | read-only | The value of tnMcsClientRemNumEntries indicates the total number of entries in the MCS database on the multi-chassis peer for a particular application. |
| C32 tnMcsClientRemLclDelEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.6 | Counter32 | read-only | The value of tnMcsClientRemLclDelEntries indicates the number of locally deleted entries in the MCS database ont he multi-chassis peer for a particular application. Locally deleted entries are entries that are not being used by the remote MCS client application. |
| C32 tnMcsClientRemAlarmedEntries | 1.3.6.1.4.1.7483.6.1.2.40.1.11.1.7 | Counter32 | read-only | The value of tnMcsClientRemAlarmedEntries indicates the number of alarmed entries in the MCS database on the multi-chassis peer for a particular application. Entries with an alarm are entries that are not being used by the remote client application due to resource constraints. |
| tnMcDomainTable | 1.3.6.1.4.1.7483.6.1.2.40.1.91 | not-accessible | A table that contains multi-chassis domain information. | |
| tnMcDomainEntry | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1 | not-accessible | Multi-chassis domain information. | |
| I32 tnMcDomainId | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.1 | Integer32 | not-accessible | The value of tnMcDomainId specifies the ID of the multi-chassis domain. |
| ROW tnMcDomainRowStatus | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.2 | RowStatus | read-create | The value of tnMcDomainRowStatus specifies the row status of this row. |
| TIT tnMcDomainDescription | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.3 | TItemDescription | read-create | The value of tnMcDomainDescription specifies the description of the multi-chassis domain. |
| IPt tnMcDomainSrcIpType | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.4 | InetAddressType | read-create | The value of tnMcDomainSrcIpType specifies the source address type of the multi-chassis domain. |
| IP tnMcDomainSrcIpAddr | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.5 | InetAddress | read-create | The value of tnMcDomainSrcIpAddr specifies the source address of the multi-chassis domain. |
| ADR tnMcDomainSrcIpMask | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.6 | InetAddressPrefixLength | read-create | The value of tnMcDomainSrcIpMask specifies the source address mask of the multi-chassis domain. |
| TNA tnMcDomainSvcName | 1.3.6.1.4.1.7483.6.1.2.40.1.91.1.7 | TNamedItemOrEmpty | read-create | The value of tnMcDomainSvcName specifies the name of the service binding to the multi-chassis domain. |
| tnMcRedundancyStatsObjs | 1.3.6.1.4.1.7483.6.1.2.40.2 | |||
| tnMcLagGlobalStatsTable | 1.3.6.1.4.1.7483.6.1.2.40.2.20 | not-accessible | The tnMcLagGlobalStatsTable has an entry for the stats of each lag that participates in a multi-chassis configuration for the indicated peer. | |
| tnMcLagGlobalStatsEntry | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1 | not-accessible | Each row entry represents stats data for a lag that participates in a multi-chassis configuration with a given peer. Rows are created or removed automatically by the system, each time a row is created or deleted in the tnMcLagConfigLagTable. | |
| C32 tnMcLagStatsPktsRx | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.1 | Counter32 | read-only | The value of tnMcLagStatsPktsRx indicates how many MC-Lag control packets with valid authentication were received on this system. |
| C32 tnMcLagStatsPktsRxKeepalive | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.2 | Counter32 | read-only | The value of tnMcLagStatsPktsRxKeepalive indicates how many valid MC-Lag control packets of type keepalive were received on this system. |
| C32 tnMcLagStatsPktsRxConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.3 | Counter32 | read-only | The value of tnMcLagStatsPktsRxConfig indicates how many valid MC-Lag control packets indicating the lag configuration were received on this system. |
| C32 tnMcLagStatsPktsRxPeerConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.4 | Counter32 | read-only | The value of tnMcLagStatsPktsRxPeerConfig indicates how many valid MC-Lag control packets indicating the peer configuration were received on this system. |
| C32 tnMcLagStatsPktsRxState | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.5 | Counter32 | read-only | The value of tnMcLagStatsPktsRxState indicates how many valid MC-Lag control packets indicating the lag state were received on this system. |
| C32 tnMcLagStatsDropPktKpaliveTask | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.6 | Counter32 | read-only | The value of tnMcLagStatsDropPktKpaliveTask indicates how many MC-Lag control packets were dropped on this system because of invalid size, authentication or unknown peer. |
| C32 tnMcLagStatsDropPktTooShort | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.7 | Counter32 | read-only | The value of tnMcLagStatsDropPktTooShort indicates how many MC-Lag control packets were dropped on this system because the packet was too small. |
| C32 tnMcLagStatsDropPktVerifyFaild | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.8 | Counter32 | read-only | The value of tnMcLagStatsDropPktVerifyFaild indicates how many MC-Lag control packets were dropped on this system because of invalid formatting. |
| C32 tnMcLagStatsDropTlvInvalidSize | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.9 | Counter32 | read-only | The value of tnMcLagStatsDropTlvInvalidSize indicates how many MC-Lag control packets were dropped on this system because of invalid size. |
| C32 tnMcLagStatsDropOutOfSeq | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.10 | Counter32 | read-only | The value of tnMcLagStatsDropOutOfSeq indicates how many MC-Lag control packets were dropped on this system because they were out of sequence. |
| C32 tnMcLagStatsDropUnknownTlv | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.11 | Counter32 | read-only | The value of tnMcLagStatsDropUnknownTlv indicates how many MC-Lag control packets were dropped on this system because they contained an unknown TLV. |
| C32 tnMcLagStatsDropTlvInvldLagId | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.12 | Counter32 | read-only | The value of tnMcLagStatsDropTlvInvldLagId indicates how many MC-Lag control packets were dropped on this system because they refer to an invalid or non multi-chassis lag. |
| C32 tnMcLagStatsDropMD5 | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.13 | Counter32 | read-only | The value of tnMcLagStatsDropMD5 indicates how many MC-Lag control packets were dropped on this system because they failed MD5 authentication. |
| C32 tnMcLagStatsDropUnknownPeer | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.14 | Counter32 | read-only | The value of tnMcLagStatsDropUnknownPeer indicates how many MC-Lag control packets were dropped on this system because they are coming from an unknown peer. |
| C32 tnMcLagStatsPktsTx | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.15 | Counter32 | read-only | The value of tnMcLagStatsPktsTx indicates how many MC-Lag control packets were transmitted from this system. |
| C32 tnMcLagStatsPktsTxKeepalive | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.16 | Counter32 | read-only | The value of tnMcLagStatsPktsTxKeepalive indicates how many MC-Lag control packets were transmitted from this system of type keepalive. |
| C32 tnMcLagStatsPktsTxConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.17 | Counter32 | read-only | The value of tnMcLagStatsPktsTxConfig indicates how many MC-Lag control packets were transmitted from this system of type lag config. |
| C32 tnMcLagStatsPktsTxPeerConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.18 | Counter32 | read-only | The value of tnMcLagStatsPktsTxPeerConfig indicates how many MC-Lag control packets were transmitted from this system of type peer config. |
| C32 tnMcLagStatsPktsTxState | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.19 | Counter32 | read-only | The value of tnMcLagStatsPktsTxState indicates how many MC-Lag control packets were transmitted from this system of type lag state. |
| C32 tnMcLagStatsPktsTxFailed | 1.3.6.1.4.1.7483.6.1.2.40.2.20.1.20 | Counter32 | read-only | The value of tnMcLagStatsPktsTxFailed indicates how many MC-Lag control packets failed to be transmitted. |
| tnMcLagPeerStatsTable | 1.3.6.1.4.1.7483.6.1.2.40.2.21 | not-accessible | The tnMcLagPeerStatsTable has an entry for each multi-chassis peer configured on this system. | |
| tnMcLagPeerStatsEntry | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1 | not-accessible | Each row entry represents a collection of statistics for a multi-chassis peer. Entries cannot be created and deleted via SNMP SET operations. | |
| C32 tnMcLagPeerStatsPktsRx | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.1 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsRx indicates how many valid MC-Lag control packets were received on this system from the peer. |
| C32 tnMcLagPeerStatsPktsRxKpalive | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.2 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsRxKpalive indicates how many valid MC-Lag control packets of type keepalive were received on this system from the peer. |
| C32 tnMcLagPeerStatsPktsRxConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.3 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsRxConfig indicates how many valid MC-Lag control packets of type lag config were received on this system from the peer. |
| C32 tnMcLagPeerStatsPktsRxPeerCfg | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.4 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsRxPeerCfg indicates how many valid MC-Lag control packets of type peer config were received on this system from the peer. |
| C32 tnMcLagPeerStatsPktsRxState | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.5 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsRxState indicates how many valid MC-Lag control packets of type lag state were received on this system from the peer. |
| C32 tnMcLagPeerStatsDropStateDsbld | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.6 | Counter32 | read-only | The value of tnMcLagPeerStatsDropStateDsbld indicates how many MC-Lag control packets were dropped on this system from the peer because the peer was administratively disabled. |
| C32 tnMcLagPeerStatsDropPktTooShrt | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.7 | Counter32 | read-only | The value of tnMcLagPeerStatsDropPktTooShrt indicates how many MC-Lag control packets were dropped on this system from the peer because the packet was too short. |
| C32 tnMcLagPeerStatsDropTlvInvldSz | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.8 | Counter32 | read-only | The value of tnMcLagPeerStatsDropTlvInvldSz indicates how many MC-Lag control packets were dropped on this system from the peer because the packet size was invalid. |
| C32 tnMcLagPeerStatsDropTlvInvldId | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.9 | Counter32 | read-only | The value of tnMcLagPeerStatsDropTlvInvldId indicates how many MC-Lag control packets were dropped on this system from the peer because the packet referred to an invalid or non multi-chassis lag. |
| C32 tnMcLagPeerStatsDropOutOfSeq | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.10 | Counter32 | read-only | The value of tnMcLagPeerStatsDropOutOfSeq indicates how many MC-Lag control packets were dropped on this system from the peer because the packet was out of sequence. |
| C32 tnMcLagPeerStatsDropUnknownTlv | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.11 | Counter32 | read-only | The value of tnMcLagPeerStatsDropUnknownTlv indicates how many MC-Lag control packets were dropped on this system from the peer because the packet contained an unknown TLV. |
| C32 tnMcLagPeerStatsDropMD5 | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.12 | Counter32 | read-only | The value of tnMcLagPeerStatsDropMD5 indicates how many MC-Lag control packets were dropped on this system from the peer because the packet failed MD5 authentication. |
| C32 tnMcLagPeerStatsPktsTx | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.13 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsTx indicates how many MC-Lag control packets were transmitted from this system to the peer. |
| C32 tnMcLagPeerStatsPktsTxKpalive | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.14 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsTxKpalive indicates how many MC-Lag control packets of type keepalive were transmitted from this system to the peer. |
| C32 tnMcLagPeerStatsPktsTxPeerCfg | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.15 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsTxPeerCfg indicates how many MC-Lag control packets of type peer config were transmitted from this system to the peer. |
| C32 tnMcLagPeerStatsPktsTxFailed | 1.3.6.1.4.1.7483.6.1.2.40.2.21.1.16 | Counter32 | read-only | The value of tnMcLagPeerStatsPktsTxFailed indicates how many MC-Lag control packets failed to be transmitted from this system to the peer. |
| tnMcLagLagStatsTable | 1.3.6.1.4.1.7483.6.1.2.40.2.22 | not-accessible | The tnMcLagLagStatsTable has an entry for each lag that participates in a multi-chassis configuration for the indicated peer. | |
| tnMcLagLagStatsEntry | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1 | not-accessible | Each row entry represents a collection of statistics for a lag that participates in a multi-chassis configuration with a given peer. Entries cannot be created and deleted via SNMP SET operations. | |
| C32 tnMcLagLagStatsPktsRxConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1.1 | Counter32 | read-only | The value of tnMcLagLagStatsPktsRxConfig indicates how many MC-Lag control packets of type lag config were received on this system from the peer for this lag. |
| C32 tnMcLagLagStatsPktsRxState | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1.2 | Counter32 | read-only | The value of tnMcLagLagStatsPktsRxState indicates how many MC-Lag control packets of type lag state were received on this system from the peer for this lag. |
| C32 tnMcLagLagStatsPktsTxConfig | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1.3 | Counter32 | read-only | The value of tnMcLagLagStatsPktsTxConfig indicates how many MC-Lag control packets of type lag config were sent on this system to the peer for this lag. |
| C32 tnMcLagLagStatsPktsTxState | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1.4 | Counter32 | read-only | The value of tnMcLagLagStatsPktsTxState indicates how many MC-Lag control packets of type lag state were sent on this system to the peer for this lag. |
| C32 tnMcLagLagStatsPktsTxFailed | 1.3.6.1.4.1.7483.6.1.2.40.2.22.1.5 | Counter32 | read-only | The value of tnMcLagLagStatsPktsTxFailed indicates how many MC-Lag control packets failed to be transmitted on this system to the peer for this lag. |
| tnMcPeerSyncStatsTable | 1.3.6.1.4.1.7483.6.1.2.40.2.23 | not-accessible | The tnMcPeerSyncStatsTable has an entry for each multi-chassis peer synchronization protocol entry. | |
| tnMcPeerSyncStatsEntry | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1 | not-accessible | Each row entry represents a collection of statistics for a multi-chassis synchronization protocol entry. Entries cannot be created and deleted via SNMP SET operations. | |
| C32 tnMcPeerSyncPktsTxAll | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.1 | Counter32 | read-only | The value of tnMcPeerSyncPktsTxAll indicates the total number of packets transmitted to the multi-chassis peer. |
| C32 tnMcPeerSyncPktsTxHello | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.2 | Counter32 | read-only | The value of tnMcPeerSyncPktsTxHello indicates the number of hello packets transmitted to the multi-chassis peer. |
| C32 tnMcPeerSyncPktsTxData | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.3 | Counter32 | read-only | The value of tnMcPeerSyncPktsTxData indicates the number of data packets transmitted to the multi-chassis peer. |
| C32 tnMcPeerSyncPktsTxOther | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.4 | Counter32 | read-only | The value of tnMcPeerSyncPktsTxOther indicates the number of all other packet types transmitted to the multi-chassis peer. |
| C32 tnMcPeerSyncPktsTxErr | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.5 | Counter32 | read-only | The value of tnMcPeerSyncPktsTxErr indicates the number of packet transmission errors. |
| C32 tnMcPeerSyncPktsRxAll | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.6 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxAll indicates the total number of packets received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxHello | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.7 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxHello indicates the number of hello packets received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxData | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.8 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxData indicates the number of hello packets received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxOther | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.9 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxOther indicates the number of all other packet types received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxErr | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.10 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxErr indicates the number of erroneous packets received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxErrHeader | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.11 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxErrHeader indicates the number of packets with header decode errors received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxErrBody | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.12 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxErrBody indicates the number of packets with body decode errors received from the multi-chassis peer. |
| C32 tnMcPeerSyncPktsRxErrSeqNum | 1.3.6.1.4.1.7483.6.1.2.40.2.23.1.13 | Counter32 | read-only | The value of tnMcPeerSyncPktsRxErrSeqNum indicates the number of packets with sequence number errors received from the multi-chassis peer. |
| U32 tnMcRedundancyStatsScalar1 | 1.3.6.1.4.1.7483.6.1.2.40.2.101 | Unsigned32 | read-only | A dummy scalar that satisfies a SNMP get request quickly when there is no 11QPE24 card provisioned. Otherwise, it has to traverse the remaining 11QPE24 MIB to get to the next applicable item. |
| U32 tnMcRedundancyStatsScalar2 | 1.3.6.1.4.1.7483.6.1.2.40.2.102 | Unsigned32 | read-only |
RFC description
Manages Nokia carrier Ethernet multi-chassis redundancy group configuration and failover state.
Start monitoring Nokia SROS routers (7750 SR, 7450 ESS) configured for multi-chassis redundancy (peer admin/oper status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.