All MIBs › TIARA-NETWORKS-DSX-TE3-MIB
Organization: Tiara Networks Inc.
Last Updated: 1999-04-23
Category: TDM and Serial Interfaces
Description: Manages Tiara Networks WAN router DSX T3 interface configuration and performance data.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIARA-NETWORKS-DSX-TE3-MIB?
TIARA-NETWORKS-DSX-TE3-MIB is a vendor-specific SNMP module for Tiara Networks WAN routers covering T3/E3 (DS3/E3) interface modules, defining line configuration, framing, and clocking parameters along with a maintenance data link (MDL) sub-table and trap definitions. It exposes line type, line coding, cable length, transmit clock source, and DS3 scrambling settings, plus MDL equipment identification fields for the physical transport interface. Its monitoring value is centered on WAN interface hardware health: correlating configured parameters (dsxT3E3IfConfigLineType, dsxT3E3IfConfigLineCode) against actual line behavior helps detect misconfiguration or physical-layer faults on a T3/E3 circuit, and the module's trap definitions (dsxT3E3Traps) provide event-driven notification of line alarm conditions. It parallels the IETF DS3/E3 interface MIB conventions (similar to RFC 3896) while remaining a Tiara-specific implementation tied to their router hardware. It is deployed on Tiara routers terminating DS3/E3 WAN trunks, with an NMS polling line configuration/status and subscribing to trap notifications for transport-layer faults, and administrators can download the TIARA-NETWORKS-DSX-TE3-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIARA-NETWORKS-DSX-TE3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Tiara Networks WAN router with T3/E3 interface module
Monitoring Examples
An operator would walk dsxT3E3IfConfigLineTable using dsxT3E3IfIndex to check dsxT3E3IfConfigLineType and dsxT3E3IfConfigLineCode against the expected provisioning for a given trunk, and verify dsxT3E3IfConfigDS3ScramblingEnable matches what the far-end carrier requires. dsxT3E3IfConfigMdlTable entries, via dsxT3E3IfConfigMdlEIC, would be checked to confirm the maintenance data link reports the correct equipment identification for the circuit. A dsxT3E3Traps notification carrying dsxT3E3TrapVariables would alert the operator to a line alarm such as loss of frame on the DS3/E3 interface.
What Can Be Monitored
- DS3/E3 line type and coding configuration
- cable length and transmit clock source
- DS3 scrambling mode
- maintenance data link equipment ID
- line alarm trap notifications
This MIB depends on
Related MIBs
Imported Objects
From RFC-1215
| TRAP-TYPE |
From SNMPv2-SMI
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| TruthValue |
From TIARA-NETWORKS-DSX-TC-MIB
| LEDState | |
| dsxT3E3IfGroup | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| dsxT3E3MIB | 1.3.6.1.4.1.3174.2.7.1.3.1 | Interface MIB definitions for Tiara T3/E3 interface modules. | ||
| dsxT3E3IfConfigGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.1 | |||
| dsxT3E3IfConfigLineTable | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1 | not-accessible | A list of T3/E3 interfaces currently configured. | |
| dsxT3E3IfConfigLineEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1 | not-accessible | An entry containing configuration for each currently active T3/E3 interface. | |
| INT dsxT3E3IfIndex | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.1 | INTEGER | not-accessible | An integer value which is an index in to the entries of ifTable (MIB-II) whose interface type is ds3 |
| INT dsxT3E3IfConfigLineType | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.2 | INTEGER | read-write | This variable indicates the variety of T3/E3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of T3/E3 is 44.736 Mbps and E3 is 34.368 Mbps. . The values, in sequence, describe: linetype-m13 ANSI T1.107-1988 linetype-cbitparity ANSI T1.107a-1990 |
| INT dsxT3E3IfConfigLineCode | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.3 | INTEGER | read-only | This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. linecode-B3ZS and linecode-HDB3 refer to the use of specified patterns of normal bits and bipolar violations which are used to replace sequences of zero bits of a specified length. |
| INT dsxT3E3IfConfigCableLength | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.4 | INTEGER | read-write | The length of the T3/E3 line in feet. This object provides information for line build out circuitry if it exists and can use this object to adjust the line build out. |
| INT dsxT3E3IfConfigTransmitClock | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.5 | INTEGER | read-write | The source of Transmit Clock. is derived from the recovered receive clock of another T3/E3 interface |
| INT dsxT3E3IfConfigDS3ScramblingMode | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.6 | INTEGER | read-write | Scrambling mode |
| T/F dsxT3E3IfConfigDS3ScramblingEnable | 1.3.6.1.4.1.3174.2.7.1.3.1.1.1.1.7 | TruthValue | read-write | To enable or disable scrambling. This is applicable only to clear channel TE3. |
| dsxT3E3IfConfigMdlTable | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2 | not-accessible | A list of T3/E3 interfaces currently configured. | |
| dsxT3E3IfConfigMdlEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1 | not-accessible | An entry containing configuration for each currently active T3/E3 interface. | |
| OCT dsxT3E3IfConfigMdlEIC | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.1 | OCTET STRING | read-write | The Equipment Identification Code (upto 10 characters) describes a specific piece of equipment |
| OCT dsxT3E3IfConfigMdlLIC | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.2 | OCTET STRING | read-write | The Location Identification Code (up to 11 characters) describes specific location |
| OCT dsxT3E3IfConfigMdlFIC | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.3 | OCTET STRING | read-write | The Frame Identification Code (upto 10 charaters ) identifies where the equipment is located within a building at a given location |
| OCT dsxT3E3IfConfigMdlUIC | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.4 | OCTET STRING | read-write | A code (upto 6 characters) that identifies the equipment location within a bay |
| OCT dsxT3E3IfConfigMdlPFI | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.5 | OCTET STRING | read-write | The Facility Identification code (upto 38 characters) identifies a specific T3/E3 path |
| OCT dsxT3E3IfConfigMdlPort | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.6 | OCTET STRING | read-write | The Port number is the designation of equipment, port that initiates the idle signal. |
| OCT dsxT3E3IfConfigMdlGenerator | 1.3.6.1.4.1.3174.2.7.1.3.1.1.2.1.7 | OCTET STRING | read-write | Gen No. is the number of signal generator that initiates the test signal |
| dsxT3E3IfAlarmConfigGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3 | |||
| dsxT3E3IfAlarmThresholdConfigTable | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1 | not-accessible | A list of TE3 interface alarm threshold configuration. | |
| dsxT3E3IfAlarmThresholdConfigEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1 | not-accessible | An entry containing alarm configuration for each currently active TE3 interface. | |
| INT dsxT3E3IfAlarmThresholdConfigIndex | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.1 | INTEGER | not-accessible | index value of the threshold configuration. |
| INT dsxT3E3IfAlarmThresholdConfigObject | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.2 | INTEGER | read-write | Configurable variables for the threshold alarm configuration. |
| INT dsxT3E3IfAlarmThresholdConfigSamplingInterval | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.3 | INTEGER | read-write | Sampling Interval for the Threshold Alarm. |
| INT dsxT3E3IfAlarmThresholdConfigSampleType | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.4 | INTEGER | read-write | Sampling type for the Threshold Alarm. |
| T/F dsxT3E3IfAlarmThresholdConfigStartupType | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.5 | TruthValue | read-write | Startup Type for the Threashold Alarm. |
| INT dsxT3E3IfAlarmThresholdConfigRisingThreshold | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.6 | INTEGER | read-write | Rising Threshold . |
| INT dsxT3E3IfAlarmThresholdConfigFallingThreshold | 1.3.6.1.4.1.3174.2.7.1.3.1.1.3.1.1.7 | INTEGER | read-write | Falling Threshold. |
| dsxT3E3IfTestConfigTable | 1.3.6.1.4.1.3174.2.7.1.3.1.1.4 | not-accessible | A list of TE3 interface test configuration. | |
| dsxT3E3IfTestConfigEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.1.4.1 | not-accessible | An entry containing test configuration for each currently active TE3 interface. | |
| INT dsxT3E3IfTestConfigType | 1.3.6.1.4.1.3174.2.7.1.3.1.1.4.1.1 | INTEGER | read-write | Test type for the TE3 interface. To perform no-test, payload-loopback-test, line-loopback-test only TestType is mandatory. To perform remote-lpup-test and remote-lpdn-test, ConfigLoopCode is mandatory |
| INT dsxT3E3IfTestConfigLoopCode | 1.3.6.1.4.1.3174.2.7.1.3.1.1.4.1.2 | INTEGER | read-write | Loopback code . |
| dsxT3E3IfStatusGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.2 | |||
| dsxT3E3IfStatusTable | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1 | not-accessible | A list of TE3 interface status entries | |
| dsxT3E3IfStatusEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1 | not-accessible | An entry containing status entry for each currently active TE3 interface. | |
| BIT dsxT3E3IfStatusLineStatus | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.1 | Bits | read-only | Line Status of the T3/E3 interface. sendPattern - TRUE if the line transmiting bit pattern, sendTE3Code - sending T3/E3 code, sendResetCode - transmits Reset Code if it is TRUE, sendPayloadcode - transmits the payload code, sendLinecode - transmitts the line code, febe - Far End Block Error, pde - pulse Density code transmission, lorc - loss of recieve clock, rfebe - recieve far end block error, ris - recieve Idle signal, rexz - recieve exessive zeros, rcvTestCode - recieve test code, loopback - loopback status , rlos - recieve loss of signal, rlof - recieve loss of frame, tais - transmit alarm indication signal, rais - recieve alarm indication signal, trai - transmit remote alarm indication, rrai - recieve remote alarm indication, |
| INT dsxT3E3IfStatusTransmitClock | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.2 | INTEGER | read-only | The source of Tranmit Clock. 'timing-line' indicates that the recovered re- ceive clock is used as the transmit clock. 'timing-internal' indicates that a local clock source is used. |
| LED dsxT3E3IfStatusTestLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.3 | LEDState | read-only | Status of TEST LED. |
| LED dsxT3E3IfStatusErrorLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.4 | LEDState | read-only | Status of the Error LED. |
| LED dsxT3E3IfStatusAisLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.5 | LEDState | read-only | Status of AIS LED. |
| LED dsxT3E3IfStatusSignalLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.6 | LEDState | read-only | Status of the Signal LED. |
| LED dsxT3E3IfStatusFrameLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.7 | LEDState | read-only | Status of the Frame LED. |
| LED dsxT3E3IfStatusYellowLED | 1.3.6.1.4.1.3174.2.7.1.3.1.2.1.1.8 | LEDState | read-only | Status of the Yellow Alarm LED. |
| dsxT3E3IfAlarmStatusTable | 1.3.6.1.4.1.3174.2.7.1.3.1.2.2 | not-accessible | A list of T3/E3 interface status entries | |
| dsxT3E3IfAlarmStatusEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.2.2.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| BIT dsxT3E3IfAlarmStatusAlarmStatus | 1.3.6.1.4.1.3174.2.7.1.3.1.2.2.1.1 | Bits | read-only | current status of all the T3/E3 interface alarms. RRAI - Recieve Remote Alarm Indication, TRAI - Transmit Remote Alarm Indication, TAIS - Transmit Alarm Indication Siganl, RLOF - Recieve Loss Of Frame, RLOS - Recieve Loss Of Sync, Loopback - Status of Loop back, rcvTestCode - Recieve Test Code, rblu - Recieve Blue Alarm, RIS - Recieve Idle Signal, REXZ - Recieve Excessive Zeros, RFBE - Recieve Frame Bit Error, RPE - Recieve Parity Error, RCPE - Recieve C-Parity Error, LORC - Loss Of Recive Clock (LORC), TPDE - transmit pulse density, RAIS - Recieve Alarm Indication Signal, TFEBE - Transmit Far End Block Alarm. |
| BIT dsxT3E3IfAlarmStatusThresholdStatus | 1.3.6.1.4.1.3174.2.7.1.3.1.2.2.1.2 | Bits | read-only | current status of all the configured threshold alarms. |
| dsxT3E3IfTestStatusTable | 1.3.6.1.4.1.3174.2.7.1.3.1.2.3 | not-accessible | A list of T3/E3 interface test status entries | |
| dsxT3E3IfTestStatusEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.2.3.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| INT dsxT3E3IfTestStatusTestType | 1.3.6.1.4.1.3174.2.7.1.3.1.2.3.1.1 | INTEGER | read-only | The test type. |
| INT dsxT3E3IfTestStatusTestState | 1.3.6.1.4.1.3174.2.7.1.3.1.2.3.1.2 | INTEGER | read-only | State of the test invoked. |
| INT dsxT3E3IfTestStatusLoopCode | 1.3.6.1.4.1.3174.2.7.1.3.1.2.3.1.3 | INTEGER | read-only | Line code for loop back test . |
| dsxT3E3IfLastTestResultTable | 1.3.6.1.4.1.3174.2.7.1.3.1.2.4 | not-accessible | A list of T3/E3 interface test status entries | |
| dsxT3E3IfLastTestResultEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.2.4.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| INT dsxT3E3IfLastTestResultTestType | 1.3.6.1.4.1.3174.2.7.1.3.1.2.4.1.1 | INTEGER | read-only | The test type. |
| INT dsxT3E3IfLastTestResultTestState | 1.3.6.1.4.1.3174.2.7.1.3.1.2.4.1.2 | INTEGER | read-only | State of the test invoked. |
| INT dsxT3E3IfLastTestResultLoopCode | 1.3.6.1.4.1.3174.2.7.1.3.1.2.4.1.3 | INTEGER | read-only | Loopcode used loopback the T3/E3 interface in previous test. |
| dsxT3E3IfStatsGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.3 | |||
| dsxT3E3IfArchiveStatsValidIntervalsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1 | not-accessible | A list of T3/E3 interface ValidIntervals entries | |
| dsxT3E3IfArchiveStatsValidIntervalsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1.1 | not-accessible | An entry containing Valid Intervals entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfAnsiArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1.1.1 | Unsigned32 | read-only | Archive Stats Valid Interval for ANSI |
| U32 dsxT3E3IfIetfArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1.1.2 | Unsigned32 | read-only | Archive Stats Valid Interval for IETF |
| U32 dsxT3E3IfUserTotalStatsValidDays | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1.1.3 | Unsigned32 | read-only | User Total Stats Valid Days |
| INT dsxT3E3IfUserArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.3.1.3.1.1.4 | INTEGER | read-write | User Archive Stats Valid Interval. Setting this variable to 0 will clear the User statistics tables |
| dsxT3E3IfErrorEventStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.2 | not-accessible | A list of T3/E3 interface error events entries | |
| dsxT3E3IfErrorEventStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.2.1 | not-accessible | An entry containing Error Events occured on T3/E3 interface. | |
| U32 dsxT3E3IfErrorEventStatsEXZ | 1.3.6.1.4.1.3174.2.7.1.3.1.3.2.1.1 | Unsigned32 | read-only | Excessive Zeros (EXZ) Error Event count |
| U32 dsxT3E3IfErrorEventStatsPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.2.1.2 | Unsigned32 | read-only | Parity Bit Error Events count |
| U32 dsxT3E3IfErrorEventStatsFEBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.2.1.3 | Unsigned32 | read-only | Far End Block Error (FEBE) event count. |
| dsxT3E3IfAnsiStatsGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3 | |||
| dsxT3E3IfAnsiCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1 | not-accessible | A list of T3/E3 interface current 15 mins interval statistics entries | |
| dsxT3E3IfAnsiCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| T/F dsxT3E3IfAnsiCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.1 | TruthValue | read-only | Current State of Availablity of the T3/E3 line |
| U32 dsxT3E3IfAnsiCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.2 | Unsigned32 | read-only | Current time for statistics |
| U32 dsxT3E3IfAnsiCurrentPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.3 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the current 15 minute interval. |
| U32 dsxT3E3IfAnsiCurrentPathStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.4 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T3/E3 interface in the current 15 minute inter- val. |
| U32 dsxT3E3IfAnsiCurrentPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.5 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the current 15 minute interval. |
| U32 dsxT3E3IfAnsiCurrentPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.6 | Unsigned32 | read-only | The number of Severely Errored Framing Seconds encountered by a T3/E3 interface in the current 15 minute interval. |
| U32 dsxT3E3IfAnsiCurrentPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.7 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T3/E3 interface in the current 15 minute in- terval. |
| U32 dsxT3E3IfAnsiCurrentLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.8 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the current 15 minute interval. |
| U32 dsxT3E3IfAnsiCurrentLineStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.9 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T3/E3 interface in the current 15 minute inter- val. |
| U32 dsxT3E3IfAnsiCurrentLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.1.1.10 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the current 15 minute interval. |
| dsxT3E3IfAnsiTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2 | not-accessible | Entries of Toatal Statistics collected over past 24 hrs on T3/E3 interface. | |
| dsxT3E3IfAnsiTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfAnsiTotalPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.1 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalPathStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.2 | Unsigned32 | read-only | The number of Errored Seconds encountered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.3 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.4 | Unsigned32 | read-only | The number of Severely Alarm Seconds encoun- tered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.5 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T3/E3 interface in the previous 24 hour in- terval. |
| U32 dsxT3E3IfAnsiTotalLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.6 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalLineStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.7 | Unsigned32 | read-only | The number of Errored Seconds encountered by a T3/E3 interface in the previous 24 hour interval. |
| U32 dsxT3E3IfAnsiTotalLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.2.1.8 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the previous 24 hour interval. |
| dsxT3E3IfAnsiArchiveIntervalStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3 | not-accessible | A list of T3/E3 interface Archive statistics entries | |
| dsxT3E3IfAnsiArchiveIntervalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfAnsiArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.1 | Unsigned32 | not-accessible | Entries of the ANSI Archive Statistics collected for T3/E3 interface. |
| U32 dsxT3E3IfAnsiArchiveIntervalPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.2 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalPathStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.3 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.4 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the current interval . |
| U32 dsxT3E3IfAnsiArchiveIntervalPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.5 | Unsigned32 | read-only | The number of Severely Errored Framing Seconds encountered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.6 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.7 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalLineStatsES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.8 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T3/E3 interface in the current interval. |
| U32 dsxT3E3IfAnsiArchiveIntervalLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.3.3.1.9 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T3/E3 interface in the current interval . |
| dsxT3E3IfIetfStatsGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4 | |||
| dsxT3E3IfIetfCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1 | not-accessible | A list of current 15 minutes IETF based Statistics collected for T3/E3 interface | |
| dsxT3E3IfIetfCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| T/F dsxT3E3IfIetfCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.1 | TruthValue | read-only | Current state of availablity of interface. |
| U32 dsxT3E3IfIetfCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT3E3IfIetfCurrentStatsPES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.3 | Unsigned32 | read-only | The number of IETF Parity Errored Seconds encoun- tered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsPSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.4 | Unsigned32 | read-only | The number of Parity Severely Errored Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.5 | Unsigned32 | read-only | The number of IETF Severely Errored Framing Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.6 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.7 | Unsigned32 | read-only | The number of Line Code Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsPCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.8 | Unsigned32 | read-only | The number of IETF Path Coding Violations reported via the far end block error count en- countered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsLES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.9 | Unsigned32 | read-only | The number of IETF Line Errored Seconds en- countered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsCCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.10 | Unsigned32 | read-only | The number of IETF C-bit Coding Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsCES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.11 | Unsigned32 | read-only | The number of IETF C-bit Errored Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfCurrentStatsCSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.1.1.12 | Unsigned32 | read-only | The number of IETF C-Bit Severely Errored Seconds. |
| dsxT3E3IfIetfTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2 | not-accessible | A list of entries for Statistics collected over 24 hrs | |
| dsxT3E3IfIetfTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfIetfTotalStatsPES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.1 | Unsigned32 | read-only | Total number of IETF Errored Seconds encoun- tered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsPSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.2 | Unsigned32 | read-only | Total number of IETF Severely Errored Seconds encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.3 | Unsigned32 | read-only | Total number of IETF Severely Errored Framing Seconds encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.4 | Unsigned32 | read-only | Total number of Unavailable Seconds encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.5 | Unsigned32 | read-only | Total number of Line Code Violations encountered by a T3/E3 interface during past 24hrs. |
| U32 dsxT3E3IfIetfTotalStatsPCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.6 | Unsigned32 | read-only | Total number of IETF Path Coding Violations encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsLES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.7 | Unsigned32 | read-only | Total number of IETF Line Errored Seconds encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsCCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.8 | Unsigned32 | read-only | Total number of IETF C-Bit Parity Code Violations encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsCES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.9 | Unsigned32 | read-only | Total number of IETF C-Bit Parity Errored Seconds encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfIetfTotalStatsCSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.2.1.10 | Unsigned32 | read-only | Total number of IETF C-Bit Parity Severely Errored Seconds encountered by a T3/E3 interface during past 24 hrs. |
| dsxT3E3IfIetfArchiveStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3 | not-accessible | A list of T3/E3 interface IETF Archive Statistics entries | |
| dsxT3E3IfIetfArchiveStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfIetfArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.1 | Unsigned32 | not-accessible | The total number of intervals for which statistics would be collected. |
| U32 dsxT3E3IfIetfArchiveStatsPES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.2 | Unsigned32 | read-only | The number of IETF Errored Seconds encoun- tered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsPSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.3 | Unsigned32 | read-only | The number of IETF Severely Errored Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.4 | Unsigned32 | read-only | The number of IETF Severely Errored Framing Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.5 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.6 | Unsigned32 | read-only | The number of Line Code Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsPCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.7 | Unsigned32 | read-only | The number of IETF Path Coding Violations reported via the far end block error count en- countered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsLES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.8 | Unsigned32 | read-only | The number of IETF Line Errored Seconds en- countered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsCCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.9 | Unsigned32 | read-only | The number of IETF C-bit Parity Code Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsCES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.10 | Unsigned32 | read-only | The number of IETF C-bit Parity Errored Seconds encountered by a T3/E3 interface. |
| U32 dsxT3E3IfIetfArchiveStatsCSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.4.3.1.11 | Unsigned32 | read-only | The number of IETF C-bit Parity Severrly Errored Seconds encountered by a T3/E3 interface. |
| dsxT3E3IfUserStatsGroup | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5 | |||
| dsxT3E3IfUserCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1 | not-accessible | A list of T3/E3 interface User Current 15 minute interval Statistics entries | |
| dsxT3E3IfUserCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| T/F dsxT3E3IfUserCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.1 | TruthValue | read-only | The Current status of availablity of the T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| U32 dsxT3E3IfUserCurrentStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.3 | Unsigned32 | read-only | The number of Line Code Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsFBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.4 | Unsigned32 | read-only | The number of Frame Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.5 | Unsigned32 | read-only | The number of Parity Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsCPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.6 | Unsigned32 | read-only | The number of C-parity Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsFEBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.7 | Unsigned32 | read-only | The number of Far End Block Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsEXZ | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.8 | Unsigned32 | read-only | The number of Excessive Zeros encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserCurrentStatsCOFA | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.1.1.9 | Unsigned32 | read-only | The number of Change Of Frame Alighnment encountered by a T3/E3 interface. |
| dsxT3E3IfUserTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2 | not-accessible | A list of entries for Statistics collected over 24 hrs | |
| dsxT3E3IfUserTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfUserTotalStatsDay | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.1 | Unsigned32 | not-accessible | The total number of Days for which statistics would be collected. |
| U32 dsxT3E3IfUserTotalStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.2 | Unsigned32 | read-only | Total number of Line Code Violations encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfUserTotalStatsFBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.3 | Unsigned32 | read-only | Total number of Frame Bit Errors encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfUserTotalStatsPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.4 | Unsigned32 | read-only | Total number of Parity Bit Errors encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfUserTotalStatsCPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.5 | Unsigned32 | read-only | Total number of C-bit Parity Bit Errors encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfUserTotalStatsFEBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.6 | Unsigned32 | read-only | Total number of Far End Block Errors encountered by a T3/E3 interface during past 24 hrs |
| U32 dsxT3E3IfUserTotalStatsEXZ | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.7 | Unsigned32 | read-only | Total number of Excessive Zeros encountered by a T3/E3 interface during past 24 hrs. |
| U32 dsxT3E3IfUserTotalStatsCOFA | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.2.1.8 | Unsigned32 | read-only | Total number of Change Of Frame Alignment encountered by a T3/E3 interface during past 24 hrs. |
| dsxT3E3IfUserLifetimeStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3 | not-accessible | A list of T3/E3 interface Statistics collected since the system was powered on entries | |
| dsxT3E3IfUserLifetimeStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfUserLifetimeStatsPES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.1 | Unsigned32 | read-only | Total number of Parity Errored Seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsPSES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.2 | Unsigned32 | read-only | Total number of Parity Severe Errored seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.3 | Unsigned32 | read-only | Total number of Severly Errored Frame Seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsUAS | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.4 | Unsigned32 | read-only | Total number of Un-Available Seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.5 | Unsigned32 | read-only | Total number of Line Code Violations encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsPCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.6 | Unsigned32 | read-only | Total number of Path Code Violations encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsLES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.7 | Unsigned32 | read-only | Total number of Line Errored Seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsCCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.8 | Unsigned32 | read-only | Total number of C-bit Code Violations encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsCES | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.9 | Unsigned32 | read-only | Total number of C-bit Errored Seconds encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsFBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.10 | Unsigned32 | read-only | Total number of Frame Bit Errors encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.11 | Unsigned32 | read-only | Total number of Parity Bit Errors encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsCPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.12 | Unsigned32 | read-only | Total number of C-bit Parity Bit Errors encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsFEBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.13 | Unsigned32 | read-only | Total number of Far End Block Errors encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsEXZ | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.14 | Unsigned32 | read-only | Total number of Excessive Zeros encountered by a T3/E3 interface since the interface is up. |
| U32 dsxT3E3IfUserLifetimeStatsCOFA | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.3.1.15 | Unsigned32 | read-only | Total number of Change Of Frame Alighnment encountered by a T3/E3 interface since the interface is up. |
| dsxT3E3IfUserArchiveStatsTable | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4 | not-accessible | A list of T3/E3 interface User Archive Statistics entries | |
| dsxT3E3IfUserArchiveStatsEntry | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1 | not-accessible | An entry containing status entry for each currently active T3/E3 interface. | |
| U32 dsxT3E3IfUserArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.1 | Unsigned32 | not-accessible | The total number of intervals for which statistics would be collected. |
| U32 dsxT3E3IfUserArchiveStatsLCV | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.2 | Unsigned32 | read-only | The number of Line Code Violations encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsFBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.3 | Unsigned32 | read-only | The number of Frame Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.4 | Unsigned32 | read-only | The number of Parity Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsCPBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.5 | Unsigned32 | read-only | The number of C Parity Bit Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsFEBE | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.6 | Unsigned32 | read-only | The number of Far End Block Errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsEXZ | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.7 | Unsigned32 | read-only | The number of Exessive Zero errors encountered by a T3/E3 interface. |
| U32 dsxT3E3IfUserArchiveStatsCOFA | 1.3.6.1.4.1.3174.2.7.1.3.1.3.5.4.1.8 | Unsigned32 | read-only | The number of Change Of Frame Alignment encountered by a T3/E3 interface. |
| dsxT3E3Traps | 1.3.6.1.4.1.3174.2.7.1.3.2 | |||
| NTF dsxT3E3AlarmOnTrap | 1.3.6.1.4.1.3174.2.7.1.3.2.0.1 | T3/E3 interface alarm trap for Alarm On state. | ||
| NTF dsxT3E3AlarmOffTrap | 1.3.6.1.4.1.3174.2.7.1.3.2.0.2 | T3/E3 interface alarm trap for Alarm Off state. | ||
| dsxT3E3TrapVariables | 1.3.6.1.4.1.3174.2.7.1.3.2.1 | |||
| INT dsxT3E3Number | 1.3.6.1.4.1.3174.2.7.1.3.2.1.1 | INTEGER | not-accessible | This variable indicates the T3/E3 interface number from where this alarm originated. |
| INT dsxT3E3AlarmType | 1.3.6.1.4.1.3174.2.7.1.3.2.1.2 | INTEGER | not-accessible | Alarm status T3/E3 interface RRAI - Recieve Receive Alarm Indication, TRAI - Transmit Receive Alarm Indication, TAIS - Transmit Alarm Indication Siganl, RLOF - Recieve Loss Of Frame, RLOS - Recieve Loss Of Sync, Loopback - Status of Loop back, rcvTestCode - Receive Test Code, rblu - Receive Blue Alarm, RIS - Receive Idle Signal, REXZ - Receive Excessive Zeros, RFBE - Receive Frame Bit Error, RPE - Receive Parity Error, RCPE - Receive C-Parity Error, LORC - Loss Of Receive Clock (LORC), TPDE - transmit pulse density, RAIS - Recieve Alarm Indication Signal, TFEBE - Transmit Far End Block Alarm, Threshold 1-10 - TRUE if it is configured. |
RFC description
Monitors T3/E3 interface configuration, alarms, and performance statistics on Tiara DSX platforms.
Start monitoring Tiara Networks WAN router with T3/E3 interface module (line config/MDL/alarm trap status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.