All MIBs › TIARA-NETWORKS-DSX-TE1-MIB
Organization: Tiara Networks Inc.
Last Updated: 1999-04-23
Category: TDM and Serial Interfaces
Description: Manages Tiara Networks WAN router DSX T1 interface configuration and performance data.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIARA-NETWORKS-DSX-TE1-MIB?
This MIB module manages the T1/E1 (DSX) WAN interface modules on Tiara Networks routers, covering the physical and line-level configuration of these digital circuits. It exposes per-line configuration data such as service mode, line mode/type/code, line build-out and cable length, transmit clock source, and time-slot mapping, alongside trap notifications for line-level alarm conditions like RAI (Remote Alarm Indication). It is used to monitor hardware/circuit status of the T1/E1 physical layer, such as line alarms, cable length settings, and clocking, which directly reflect the health of the underlying leased-line or carrier circuit rather than higher-layer traffic. It follows the general structure of IETF DS1/E1 interface MIB conventions while being a Tiara-specific implementation. It is deployed on Tiara Networks WAN routers connecting to carrier-provided T1 or E1 leased lines. Engineers can download the TIARA-NETWORKS-DSX-TE1-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIARA-NETWORKS-DSX-TE1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Tiara Networks WAN router (T1/E1 module)
Monitoring Examples
A WAN engineer would poll dsxT1E1IfConfigLineType and dsxT1E1IfConfigLineCode to confirm the interface is set to match the carrier's provisioned framing and line coding (e.g., ESF/B8ZS), and check dsxT1E1IfConfigRaiAlarm to see whether the far end is reporting a remote alarm indication signaling a fault on that leg of the circuit. dsxT1E1IfConfigCableLength and dsxT1E1IfConfigLBO would be reviewed after a line reports excessive errors, since an incorrect line build-out setting for the actual cable run is a common cause of T1/E1 signal degradation. The dsxT1E1Traps notification group alerts operators immediately when such alarm conditions occur, rather than requiring constant polling of the dsxT1E1IfConfigLineTable.
What Can Be Monitored
- T1/E1 line alarms (RAI)
- line mode/type/code configuration
- cable length/line build-out
- transmit clock source
- time-slot mapping
This MIB depends on
Related MIBs
Imported Objects
From RFC-1215
| TRAP-TYPE |
From RFC1213-MIB
| DisplayString |
From SNMPv2-SMI
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| TruthValue |
From TIARA-NETWORKS-DSX-TC-MIB
| dsxT1E1IfGroup | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| dsxT1E1MIB | 1.3.6.1.4.1.3174.2.7.1.2.1 | Interface MIB definitions for Tiara T1/E1 interface modules. | ||
| dsxT1E1IfConfigGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.1 | |||
| dsxT1E1IfConfigLineTable | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1 | not-accessible | A list of T1/E1 interfaces currently configured. | |
| dsxT1E1IfConfigLineEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1 | not-accessible | An entry containing configuration for each T1/E1 interface. | |
| INT dsxT1E1IfIndex | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.1 | INTEGER | not-accessible | An integer value which is an index in to the entries of ifTable (MIB-II) whose interface type is ds1 |
| T/F dsxT1E1IfConfigServiceMode | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.2 | TruthValue | read-write | Indicates the T1/E1 interface is in service if it is TRUE. |
| INT dsxT1E1IfConfigLineMode | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.3 | INTEGER | read-write | Line Mode for this T1/E1 interface |
| INT dsxT1E1IfConfigLineType | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.4 | INTEGER | read-write | This variable indicates the variety of T1/E1 interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 |
| INT dsxT1E1IfConfigLineCode | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.5 | INTEGER | read-write | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. ami refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data. |
| INT dsxT1E1IfConfigLBO | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.6 | INTEGER | read-write | Signal attenuation at 772 kHz lbo-zero-db carrier advised LBO code A 0.0 - 5.5 db lbo-75-db carrier advised LBO code B 7.5 - 13.0 db lbo-15-db carrier advised LBO code C 15.0 - 22.0 db This variable can be set only for CSU linemode |
| INT dsxT1E1IfConfigCableLength | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.7 | INTEGER | read-write | This variable specifies the length of the cable in feet. |
| INT dsxT1E1IfConfigRaiAlarm | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.8 | INTEGER | read-write | Configurition of Remote Alarm Indication Alarm generation and detection. |
| INT dsxT1E1IfConfigTransmitClock | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.9 | INTEGER | read-write | The source of Transmit Clock. 'timing-line' indicates that the recovered re- ceive clock is used as the transmit clock. 'timing-internal' indicates that a local clock source is used. |
| OCT dsxT1E1IfConfigTimeSlotMap | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.10 | OCTET STRING | read-only | Time slot map of the T1/E1 line that are being used if it is used corresponding bit position is set. |
| STR dsxT1E1IfCircuitId | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.11 | DisplayString | read-write | |
| STR dsxT1E1IfContactInfo | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.12 | DisplayString | read-write | |
| STR dsxT1E1IfDescription | 1.3.6.1.4.1.3174.2.7.1.2.1.1.1.1.13 | DisplayString | read-write | |
| dsxT1E1IfConfigFdlTable | 1.3.6.1.4.1.3174.2.7.1.2.1.1.2 | not-accessible | A list of T1/E1 interface currently configured. | |
| dsxT1E1IfConfigFdlEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.1.2.1 | not-accessible | Configurable Facility Data Link (FDL) field for enable/disable the FDL utility on T1/E1 interface. | |
| INT dsxT1E1IfConfigFdl | 1.3.6.1.4.1.3174.2.7.1.2.1.1.2.1.1 | INTEGER | read-write | The configuration FDL type fdl-ansi-only - only supports ANSI FDL , fdl-att-only only supports ATT FDL, fdl-ansi-att supports both ANSI and ATT FDL. |
| INT dsxT1E1IfConfigFdlCsuDsuType | 1.3.6.1.4.1.3174.2.7.1.2.1.1.2.1.2 | INTEGER | read-write | The configuration of the type of equipment fdl-csu - responds to only CSU FDL requests fdl-dsu - responds to only DSU FDL requests fdl-csudsu - responds to both CSU and DSU requests. |
| dsxT1E1IfAlarmConfigGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3 | |||
| dsxT1E1IfAlarmThresholdConfigTable | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1 | not-accessible | A list of T1/E1 interface alarm threshold configuration parameters. | |
| dsxT1E1IfAlarmThresholdConfigEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1 | not-accessible | An entry containing alarm configuration parameters for each T1/E1 interface. | |
| INT dsxT1E1IfAlarmThresholdConfigIndex | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.1 | INTEGER | not-accessible | Index of the Threshold Alarms 1 - 10. |
| INT dsxT1E1IfAlarmThresholdConfigObject | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.2 | INTEGER | read-write | Threshold alarm - variables being monitored. |
| INT dsxT1E1IfAlarmThresholdConfigSamplingInterval | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.3 | INTEGER | read-write | Sampling Interval is the time between each sampling period. |
| INT dsxT1E1IfAlarmThresholdConfigSampleType | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.4 | INTEGER | read-write | Threshold Alarm: Sampling type sample-absolute - compares the monitored variable value againist the thresholds, sample-delta - compares the monitored variable value change from previous interval against thresholds. |
| T/F dsxT1E1IfAlarmThresholdConfigStartupType | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.5 | TruthValue | read-write | Threshold Alarm :if TRUE the first sample will be ignored if thresholds are crossed. |
| INT dsxT1E1IfAlarmThresholdConfigRisingThreshold | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.6 | INTEGER | read-write | Threshold Alarm: Rising threshold limit |
| INT dsxT1E1IfAlarmThresholdConfigFallingThreshold | 1.3.6.1.4.1.3174.2.7.1.2.1.1.3.1.1.7 | INTEGER | read-write | Threshold Alarm: Falling threshold limit |
| dsxT1E1IfTestConfigTable | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4 | not-accessible | A list of T1/E1 interface test configuration parameters. | |
| dsxT1E1IfTestConfigEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4.1 | not-accessible | An entry containing test configuration parameters for each currently T1/E1 interface. | |
| INT dsxT1E1IfTestConfigType | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4.1.1 | INTEGER | read-write | Test type. Specifies the type of test to execute on this T1/E1 interface. To perform no-test, payload-loopback-test, line-loopback-test only TestType is mandatory. To perform pattern-test, ConfigTime and ConfigPattern are mandatory. To perform remote-lpup-test and remote-lpdn-test, ConfigLoopCode is mandatory |
| U32 dsxT1E1IfTestConfigTime | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4.1.2 | Unsigned32 | read-write | Test time. when set to 0, test time is unlimited. Otherwise duration of test, specified in seconds. |
| INT dsxT1E1IfTestConfigPattern | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4.1.3 | INTEGER | read-write | Bit Pattern type used in testing T1/E1 for Pattern Test. |
| INT dsxT1E1IfTestConfigLoopCode | 1.3.6.1.4.1.3174.2.7.1.2.1.1.4.1.4 | INTEGER | read-write | Type of loopcode is used for loopback test. |
| dsxT1E1IfStatusGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.2 | |||
| dsxT1E1IfStatusTable | 1.3.6.1.4.1.3174.2.7.1.2.1.2.1 | not-accessible | A list of T1/E1 interface status entries | |
| dsxT1E1IfStatusEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.2.1.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| BIT dsxT1E1IfStatusLineStatus | 1.3.6.1.4.1.3174.2.7.1.2.1.2.1.1.1 | Bits | read-only | The summary of the status RRAIStatus - Recieve RAI (Recieve Alarm Indication), TRAIStatus - Transmit RAI , RLOSStatus - Recieve Loss Of Sync, RISStatus - Recieve Idle Signal REXZStatus - Recieve Excessive Zeros, LORCStatus - Loss Of Recive Clock (LORC), TDEStatus - transmit pulse density, SendLineCode - transmit linecode SendPayLoadCode - transmit paylode code SendResetCode - transmit reset code, SendTE1Code - transmit T1/E1 linecode, SendPattern - transmit T1/E1 Pattern, RcvTestCode - recive test code, LoopbackStatus - Status of Loop back, TAISStatus - Transmit Alarm Indication Siganl, RAISStatus - Recieve Alarm Indication Signal, LOFStatus - Loss Of Frame. |
| INT dsxT1E1IfStatusTransmitClock | 1.3.6.1.4.1.3174.2.7.1.2.1.2.1.1.2 | INTEGER | read-only | The source of Tranmit Clock. 'timing-line' indicates that the recovered re- ceive clock is used as the transmit clock. 'timing-internal' indicates that a local clock source is used. |
| dsxT1E1IfAlarmStatusTable | 1.3.6.1.4.1.3174.2.7.1.2.1.2.2 | not-accessible | A list of T1/E1 interface alarm status entries | |
| dsxT1E1IfAlarmStatusEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.2.2.1 | not-accessible | An entry containing alarm status for each T1/E1 interface. | |
| BIT dsxT1E1IfAlarmStatusAlarmStatus | 1.3.6.1.4.1.3174.2.7.1.2.1.2.2.1.1 | Bits | read-only | Alarm Status of T1/E1 interface. RRAI - Recieve Rx Alarm Indication, TRAI - Transmit Rx Alarm Indication, RAIS - Recieve Alarm Indication Signal, TAIS - Transmit Alarm Indication Signal, RLOF - Recieve Loss Of Frame, RLOS - Recieve Loss Of Signal, Loopback - if looped back state is true, RIS - Recieve Idle Signal, REXZ - Recieve Excessive Zeros, RFEBE - Recieve Far End Block Error, RPE - Recieve Parity Error, RCPE - Recieve C-Parity Error, LORC - Loss Of Recieve Clock, TPDE - Transmit Pulse DEnsity, TFEBE - Transmit Far End Block Error, ibTest - InBand Test running if true. |
| BIT dsxT1E1IfAlarmStatusThresholdStatus | 1.3.6.1.4.1.3174.2.7.1.2.1.2.2.1.2 | Bits | read-only | Status of the user configurable threshold Alarms 1 means present. |
| dsxT1E1IfTestStatusTable | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfTestStatusEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1 | not-accessible | An entry containing test status entry for each T1/E1 interface. | |
| INT dsxT1E1IfTestStatusTestType | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.1 | INTEGER | read-only | Test type initiated on T1/E1 line. |
| U32 dsxT1E1IfTestStatusTestTime | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.2 | Unsigned32 | read-only | Time elapsed since the test started on T1/E1 line |
| INT dsxT1E1IfTestStatusTestState | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.3 | INTEGER | read-only | Current state of the running test on T1/E1 line |
| INT dsxT1E1IfTestStatusTestPattern | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.4 | INTEGER | read-only | Bit Pattern generated to test the T1/E1, only relevent to Pattern Test. |
| U32 dsxT1E1IfTestStatusLockedSeconds | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.5 | Unsigned32 | read-only | Count of seconds, during which the pattern is synchronized |
| U32 dsxT1E1IfTestStatusSyncLossCount | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.6 | Unsigned32 | read-only | Counter for the pattern synchronization losses |
| U32 dsxT1E1IfTestStatusErrorCount | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.7 | Unsigned32 | read-only | Counter for the Bit error during the test |
| INT dsxT1E1IfTestStatusLoopCode | 1.3.6.1.4.1.3174.2.7.1.2.1.2.3.1.8 | INTEGER | read-only | The loop codes transmitted on the T1/E1 interface Only relevent to the Remote LoopUp and Remote LoopDown tests. |
| dsxT1E1IfLastTestResultTable | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4 | not-accessible | A list of T1/E1 interface previous test status entries | |
| dsxT1E1IfLastTestResultEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1 | not-accessible | An entry containing previous test status entry for each T1/E1 interface. | |
| INT dsxT1E1IfLastTestResultTestType | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.1 | INTEGER | read-only | Status of the previous test conducted on this T1/E1 interface, this field corresponds to Type of Test conducted |
| U32 dsxT1E1IfLastTestResultTestTime | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.2 | Unsigned32 | read-only | Duration of the test conducted in previous test |
| INT dsxT1E1IfLastTestResultTestState | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.3 | INTEGER | read-only | This field shows in which state previous test was ended |
| INT dsxT1E1IfLastTestResultTestPattern | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.4 | INTEGER | read-only | If the previous test conducted was pattern test, This field will have type of pattern used to test. |
| U32 dsxT1E1IfLastTestResultLockedSeconds | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.5 | Unsigned32 | read-only | Duration in which signal was synchronized while under test. |
| U32 dsxT1E1IfLastTestResultSyncLossCount | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.6 | Unsigned32 | read-only | Counter for the pattern synchronization losses in previous test results. |
| U32 dsxT1E1IfLastTestResultErrorCount | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.7 | Unsigned32 | read-only | Counter for the Bit error during the test in previous test |
| INT dsxT1E1IfLastTestResultLoopCode | 1.3.6.1.4.1.3174.2.7.1.2.1.2.4.1.8 | INTEGER | read-only | Type loopcode used to put interface under remote loop back |
| dsxT1E1IfStatsGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.3 | |||
| dsxT1E1IfArchiveStatsValidIntervalsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1 | not-accessible | Number of intervals available in archive statistics table for this T1/E1 interface | |
| dsxT1E1IfArchiveStatsValidIntervalsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1 | not-accessible | An entry containing statistics entry for each T1/E1 interface. | |
| U32 dsxT1E1IfAnsiArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1.1 | Unsigned32 | read-only | Total number of archived statistics collected according to ANSI standards. |
| U32 dsxT1E1IfAttArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1.2 | Unsigned32 | read-only | Total number of archived statistics collected according to ATT standards. |
| U32 dsxT1E1IfIetfArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1.3 | Unsigned32 | read-only | Total number of archived statistics collected according to IETF standards. |
| U32 dsxT1E1IfUserTotalStatsValidDays | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1.4 | Unsigned32 | read-only | Total number of days archived statistics collected according to User definations. |
| INT dsxT1E1IfUserArchiveStatsValidIntervals | 1.3.6.1.4.1.3174.2.7.1.2.1.3.1.1.5 | INTEGER | read-write | User Archive Stats Valid Interval. Setting this variable to 0 will clear all the User Statistics Tables |
| dsxT1E1IfAnsiStatsGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2 | |||
| dsxT1E1IfAnsiCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1 | not-accessible | Statistics collected according ANSI standards and collected in current 900 secondss period. | |
| dsxT1E1IfAnsiCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1 | not-accessible | Statistics collected in current 900 secs ( i.e. 15 mins) kept in this table | |
| T/F dsxT1E1IfAnsiCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.1 | TruthValue | read-only | The State of T1/E1 line according to ANSI standards |
| U32 dsxT1E1IfAnsiCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the current error measurement period |
| U32 dsxT1E1IfAnsiCurrentPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.3 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAnsiCurrentPathStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.4 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T1/E1 interface in the current 15 minute inter- val. |
| U32 dsxT1E1IfAnsiCurrentPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.5 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAnsiCurrentPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.6 | Unsigned32 | read-only | Seconds with Severe Alarms |
| U32 dsxT1E1IfAnsiCurrentPathStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.7 | Unsigned32 | read-only | The number of Controlled Slip Seconds encoun- tered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAnsiCurrentPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.8 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface in the current 15 minute in- terval. |
| U32 dsxT1E1IfAnsiCurrentLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.9 | Unsigned32 | read-only | The number of Line Coding Violations encoun- tered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAnsiCurrentLineStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.10 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T1/E1 interface in the current 15 minute inter- val. |
| U32 dsxT1E1IfAnsiCurrentLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.1.1.11 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the current 15 minute interval. |
| dsxT1E1IfAnsiTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2 | not-accessible | Table for the Total Statistics over past 24 hrs | |
| dsxT1E1IfAnsiTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1 | not-accessible | Table for the Total Statistics over past 24 hrs | |
| U32 dsxT1E1IfAnsiTotalPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.1 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalPathStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.2 | Unsigned32 | read-only | The number of Errored Seconds encountered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.3 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.4 | Unsigned32 | read-only | Total No seconds with Severe Alarms in past 24 hrs |
| U32 dsxT1E1IfAnsiTotalPathStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.5 | Unsigned32 | read-only | The number of Controlled Slip Seconds encoun- tered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.6 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface in the previous 24 hour in- terval. |
| U32 dsxT1E1IfAnsiTotalLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.7 | Unsigned32 | read-only | The number of Line Coding Violations encoun- tered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalLineStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.8 | Unsigned32 | read-only | The number of Errored Seconds encountered by a T1/E1 interface in the previous 24 hour interval. |
| U32 dsxT1E1IfAnsiTotalLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.2.1.9 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the previous 24 hour interval. |
| dsxT1E1IfAnsiArchiveIntervalStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfAnsiArchiveIntervalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfAnsiArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.1 | Unsigned32 | not-accessible | Number of Intervals available in archive table |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.2 | Unsigned32 | read-only | The number of Path Coding Violations encoun- tered by a T1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.3 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a DS3 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.4 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the archive intervals . |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsSAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.5 | Unsigned32 | read-only | The number of Severely Errored Framing Seconds encountered by a T1/E1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.6 | Unsigned32 | read-only | The number of Controlled Slip Seconds encountered by a T1/E1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalPathStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.7 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalLineStatsCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.8 | Unsigned32 | read-only | The number of Line Coding Violations encoun- tered by a T1/E1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalLineStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.9 | Unsigned32 | read-only | The number of Errored Seconds, encountered by a T1/E1 interface in the archive intervals. |
| U32 dsxT1E1IfAnsiArchiveIntervalLineStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.2.3.1.10 | Unsigned32 | read-only | The number of Severely Errored Seconds encoun- tered by a T1/E1 interface in the archive intervals . |
| dsxT1E1IfAttStatsGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3 | |||
| dsxT1E1IfAttCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1 | not-accessible | A list of T1/E1 interface statistics for current interval | |
| dsxT1E1IfAttCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1 | not-accessible | An entry containing statistics for each currently active T1/E1 interface. | |
| T/F dsxT1E1IfAttCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.1 | TruthValue | read-only | The Current state of availablity of T1/E1 interface |
| U32 dsxT1E1IfAttCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the far end current error-measurement period. |
| U32 dsxT1E1IfAttCurrentStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.3 | Unsigned32 | read-only | The number of Far Far End Errored EVents en- countered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAttCurrentStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.4 | Unsigned32 | read-only | The number of Far Far End Errored Seconds en- countered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAttCurrentStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.5 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface in the current 15 minute in- terval. |
| U32 dsxT1E1IfAttCurrentStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.6 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAttCurrentStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.7 | Unsigned32 | read-only | The number of Far End Severely Errored Seconds encountered by a T1/E1 interface in the current 15 minute interval. |
| U32 dsxT1E1IfAttCurrentStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.8 | Unsigned32 | read-only | The number of loss of frames occurred in the current 15 minute interval. |
| U32 dsxT1E1IfAttCurrentStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.1.1.9 | Unsigned32 | read-only | The number of Far End Controlled Slip Seconds encountered by a T1/E1 interface in the current interval. |
| dsxT1E1IfAttTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfAttTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfAttTotalStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.1 | Unsigned32 | read-only | Invoke the configured test. |
| U32 dsxT1E1IfAttTotalStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.2 | Unsigned32 | read-only | The number of Near End Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfAttTotalStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.3 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttTotalStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.4 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttTotalStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.5 | Unsigned32 | read-only | The number of Near End Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttTotalStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.6 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfAttTotalStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.2.1.7 | Unsigned32 | read-only | The number of Near End Controlled Slip Seconds encountered by a T1/E1 interface. |
| dsxT1E1IfAttArchiveStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfAttArchiveStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfAttArchiveInterval | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.1 | Unsigned32 | not-accessible | Time interval for archiving the statistics. |
| U32 dsxT1E1IfAttArchiveStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.2 | Unsigned32 | read-only | Invoke the configured test. |
| U32 dsxT1E1IfAttArchiveStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.3 | Unsigned32 | read-only | The number of Near End Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfAttArchiveStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.4 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttArchiveStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.5 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttArchiveStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.6 | Unsigned32 | read-only | The number of Near End Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfAttArchiveStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.7 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfAttArchiveStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.3.3.1.8 | Unsigned32 | read-only | The number of Near End Controlled Slip Seconds encountered by a T1/E1 interface. |
| dsxT1E1IfIetfStatsGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4 | |||
| dsxT1E1IfIetfCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfIetfCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| T/F dsxT1E1IfIetfCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.1 | TruthValue | read-only | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT1E1IfIetfCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT1E1IfIetfCurrentStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.3 | Unsigned32 | read-only | The number of IETF Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.4 | Unsigned32 | read-only | The number of Far End Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.5 | Unsigned32 | read-only | The number of IETF Severely Errored Framing Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.6 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.7 | Unsigned32 | read-only | The number of IETF Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsPCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.8 | Unsigned32 | read-only | The number of IETF Path Coding Violations reported via the far end block error count en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsLES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.9 | Unsigned32 | read-only | The number of IETF Line Errored Seconds en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.10 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsDM | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.11 | Unsigned32 | read-only | The number of Degraded Minutes (DMs) encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfCurrentStatsLCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.1.1.12 | Unsigned32 | read-only | Invoke the configured test. |
| dsxT1E1IfIetfTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfIetfTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfIetfTotalStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.1 | Unsigned32 | read-only | The number of IETF Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.2 | Unsigned32 | read-only | The number of IETF Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.3 | Unsigned32 | read-only | The number of IETF Severely Errored Framing Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.4 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.5 | Unsigned32 | read-only | The number of IETF Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsPCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.6 | Unsigned32 | read-only | The number of IETF Path Coding Violations reported via the far end block error count en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsLES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.7 | Unsigned32 | read-only | The number of IETF Line Errored Seconds en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.8 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsDM | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.9 | Unsigned32 | read-only | The number of Degraded Minutes (DMs) encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfTotalStatsLCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.2.1.10 | Unsigned32 | read-only | Invoke the configured test. |
| dsxT1E1IfIetfArchiveStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfIetfArchiveStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfIetfArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.1 | Unsigned32 | not-accessible | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT1E1IfIetfArchiveStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.2 | Unsigned32 | read-only | The number of IETF Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.3 | Unsigned32 | read-only | The number of IETF Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsSEFS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.4 | Unsigned32 | read-only | The number of IETF Severely Errored Framing Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.5 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.6 | Unsigned32 | read-only | The number of IETF Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsPCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.7 | Unsigned32 | read-only | The number of IETF Path Coding Violations reported via the far end block error count en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsLES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.8 | Unsigned32 | read-only | The number of IETF Line Errored Seconds en- countered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.9 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsDM | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.10 | Unsigned32 | read-only | The number of Degraded Minutes (DMs) encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfIetfArchiveStatsLCV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.4.3.1.11 | Unsigned32 | read-only | Invoke the configured test. |
| dsxT1E1IfUserStatsGroup | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5 | |||
| dsxT1E1IfUserCurrentStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfUserCurrentStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| T/F dsxT1E1IfUserCurrentStatsUASState | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.1 | TruthValue | read-only | Current state of availablity of T1/E1 interface |
| U32 dsxT1E1IfUserCurrentStatsTimeInCurrent | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.2 | Unsigned32 | read-only | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT1E1IfUserCurrentStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.3 | Unsigned32 | read-only | Invoke the configured test. |
| U32 dsxT1E1IfUserCurrentStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.4 | Unsigned32 | read-only | The number of Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfUserCurrentStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.5 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserCurrentStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.6 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserCurrentStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.7 | Unsigned32 | read-only | The number of Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserCurrentStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.8 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfUserCurrentStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.9 | Unsigned32 | read-only | The number of Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserCurrentStatsBPV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.10 | Unsigned32 | read-only | The number of Bipolar Violation Error Event occurred for this interface. |
| U32 dsxT1E1IfUserCurrentStatsOOF | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.11 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| U32 dsxT1E1IfUserCurrentStatsCRC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.1.1.12 | Unsigned32 | read-only | The number of CRC Defects that occurred for this interface. |
| dsxT1E1IfUserTotalStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2 | not-accessible | A list of T1/E1 interface test status entries | |
| dsxT1E1IfUserTotalStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfUserTotalStatsDay | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.1 | Unsigned32 | not-accessible | Total number of days elapsed since event recording started for this interface. |
| U32 dsxT1E1IfUserTotalStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.2 | Unsigned32 | read-only | Invoke the configured test. |
| U32 dsxT1E1IfUserTotalStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.3 | Unsigned32 | read-only | The number of Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfUserTotalStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.4 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserTotalStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.5 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserTotalStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.6 | Unsigned32 | read-only | The number of Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserTotalStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.7 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfUserTotalStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.8 | Unsigned32 | read-only | The number of Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserTotalStatsBPV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.9 | Unsigned32 | read-only | The number of Bipolar Violation Error Event occurred for this interface. |
| U32 dsxT1E1IfUserTotalStatsOOF | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.10 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| U32 dsxT1E1IfUserTotalStatsCRC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.2.1.11 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| dsxT1E1IfUserLifetimeStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3 | not-accessible | Table maintained to keep the statistics for the whole lifetime of the system since it is first powered on. | |
| dsxT1E1IfUserLifetimeStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfUserLifetimeStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.1 | Unsigned32 | read-only | The Total number of Error Events occured during since the system brought up |
| U32 dsxT1E1IfUserLifetimeStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.2 | Unsigned32 | read-only | The number of Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfUserLifetimeStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.3 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserLifetimeStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.4 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserLifetimeStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.5 | Unsigned32 | read-only | The number of Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserLifetimeStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.6 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfUserLifetimeStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.7 | Unsigned32 | read-only | The number of Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserLifetimeStatsBPV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.8 | Unsigned32 | read-only | The number of Bipolar Violation Error Event occurred for this interface. |
| U32 dsxT1E1IfUserLifetimeStatsOOF | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.9 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| U32 dsxT1E1IfUserLifetimeStatsCRC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.3.1.10 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| dsxT1E1IfUserArchiveStatsTable | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4 | not-accessible | The table maintained to keep last 24 hrs statistics in | |
| dsxT1E1IfUserArchiveStatsEntry | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1 | not-accessible | An entry containing status entry for each currently active T1/E1 interface. | |
| U32 dsxT1E1IfUserArchiveStatsInterval | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.1 | Unsigned32 | not-accessible | The number of seconds that have elapsed since the beginning of the IETF current error-measurement period. |
| U32 dsxT1E1IfUserArchiveStatsEEV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.2 | Unsigned32 | read-only | Error Events collected over each period of 15 mins |
| U32 dsxT1E1IfUserArchiveStatsES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.3 | Unsigned32 | read-only | The number of Errored Seconds encoun- tered by a T1/E1 interface. |
| U32 dsxT1E1IfUserArchiveStatsUAS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.4 | Unsigned32 | read-only | The number of Unavailable Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserArchiveStatsBES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.5 | Unsigned32 | read-only | The number of Bursty Errored Seconds (BESs) encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserArchiveStatsSES | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.6 | Unsigned32 | read-only | The number of Severely Errored Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserArchiveStatsLOFC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.7 | Unsigned32 | read-only | Count of loss of frames. |
| U32 dsxT1E1IfUserArchiveStatsCSS | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.8 | Unsigned32 | read-only | The number of Controlled Slip Seconds encountered by a T1/E1 interface. |
| U32 dsxT1E1IfUserArchiveStatsBPV | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.9 | Unsigned32 | read-only | The number of Bipolar Violation Error Event occurred for this interface. |
| U32 dsxT1E1IfUserArchiveStatsOOF | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.10 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| U32 dsxT1E1IfUserArchiveStatsCRC | 1.3.6.1.4.1.3174.2.7.1.2.1.3.5.4.1.11 | Unsigned32 | read-only | The number of Out of Frame Defect occurred for this interface. |
| dsxT1E1Traps | 1.3.6.1.4.1.3174.2.7.1.2.2 | |||
| NTF dsxT1E1AlarmOnTrap | 1.3.6.1.4.1.3174.2.7.1.2.2.0.1 | T1/E1 interface alarm traps for the Alarm On state. | ||
| NTF dsxT1E1AlarmOffTrap | 1.3.6.1.4.1.3174.2.7.1.2.2.0.2 | T1/E1 interface alarm trap for the Alarm Off state. | ||
| dsxT1E1TrapVariables | 1.3.6.1.4.1.3174.2.7.1.2.2.1 | |||
| INT dsxT1E1Number | 1.3.6.1.4.1.3174.2.7.1.2.2.1.1 | INTEGER | not-accessible | This is the T1/E1 number of the interface from where this alarm is originating. |
| INT dsxT1E1Type | 1.3.6.1.4.1.3174.2.7.1.2.2.1.2 | INTEGER | not-accessible | This variable indicates whether this T1/E1 interface is with in a T3/E3 or by itself. |
| INT dsxT1E1T3Number | 1.3.6.1.4.1.3174.2.7.1.2.2.1.3 | INTEGER | not-accessible | This variable is applicable only if dsxT1E1Type is 'type_t1_within_ct3' and it indicates the T3/E3 interface number this T1 belongs to. |
| INT dsxT1E1AlarmType | 1.3.6.1.4.1.3174.2.7.1.2.2.1.4 | INTEGER | not-accessible | Status of alarms for the T1/E1 interface RRAI - Recieve RAI (Recieve Alarm Indication), RLOS - Recieve Loss Of Sync, REXZ - Recieve Excessive Zeros, LORC - Loss Of Receive Clock (LORC), TPDE - transmit pulse density, TAIS - Transmit Alarm Indication Signal, RAIS - Recieve Alarm Indication Signal, RLOF - Recieve Loss Of Frame. RFBE - Recieve Frame Bit Error, ROOF - Recieve Out Of Frame, TRAI - Transmit RAI (Recieve Alarm Indication), Threshold 1-10 : TRUE if it is configured. |
RFC description
SNMP MIB for Tiara Networks DSX equipment managing T1 and E1 interface operations, supporting digital signal hierarchy management and circuit provisioning on Tiara devices.
Start monitoring Tiara Networks WAN routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.