TELDAT-CFG-PROTOCOL-IP-MIB

All MIBs › TELDAT-CFG-PROTOCOL-IP-MIB

Category: Teldat Router Management

Description: Configures IP protocol parameters on Teldat routers, including addressing, routing settings, and interface IP policies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-CFG-PROTOCOL-IP-MIB?

TELDAT-CFG-PROTOCOL-IP-MIB is a proprietary configuration MIB from Teldat, a Spanish manufacturer of enterprise and branch-office routers, used to set IP protocol parameters on Teldat router firmware. It exposes configuration-oriented data such as interface IP addressing, subnet/mask settings, routing parameters, and per-interface IP policy rather than free-running performance counters. Because it lets an operator read back the currently configured IP addresses and routing policy in effect on each interface, it is chiefly useful for verifying the software configuration state of the router - confirming that address or routing changes pushed via SNMP SET or the CLI actually took hold - rather than for hardware health monitoring. It is a Teldat proprietary extension that is normally used alongside standard IETF IP-MIB and IF-MIB objects to get a complete picture of the device's network-layer state. It is typically deployed on Teldat CPE and branch-office routers managed by a central NMS that provisions and audits IP addressing across a fleet of devices. Network engineers evaluating or troubleshooting this functionality can download the TELDAT-CFG-PROTOCOL-IP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-CFG-PROTOCOL-IP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat router
Teldat branch-office/CPE router

Monitoring Examples

No sample object names were supplied for this module in the source excerpt, so specific OIDs cannot be cited, but its function corresponds to a per-interface IP configuration table (addresses, mask, and IP policy) analogous to Teldat's other CFG-PROTOCOL-* modules. An administrator would poll this table after a remote provisioning change to confirm an interface received its intended address and routing policy rather than reverting to a stale configuration. A mismatch between the expected and reported address/policy would indicate a failed or partially-applied configuration push.

What Can Be Monitored

configured IP interface addresses
interface IP policy settings
routing-related IP configuration state

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From TELDAT-SW-STRUCTURE-MIB

telProdNpConfProtocol

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
telProdNpConfProtIP	1.3.6.1.4.1.2007.4.1.1.5.1
telProdNpIPGloGroup	1.3.6.1.4.1.2007.4.1.1.5.1.1
IP telProdNpIPGloDirIPInternal	1.3.6.1.4.1.2007.4.1.1.5.1.1.1	IpAddress	read-write	Internal IP address of the packets.
IP telProdNpIPGloRouterID	1.3.6.1.4.1.2007.4.1.1.5.1.1.2	IpAddress	read-write	IP address with which router is identified.
INT telProdNpIPGloSizeRoutingTable	1.3.6.1.4.1.2007.4.1.1.5.1.1.3	INTEGER	read-write	Maximum routing table size. 0 = unlimited. 64..1000000000 = routing table size limit. Default value is 0 (unlimited).
INT telProdNpIPGloSizeBuffReassembly	1.3.6.1.4.1.2007.4.1.1.5.1.1.4	INTEGER	read-write	Reassembly buffer size. Default value is 12000
INT telProdNpIPGloSizeRoutingCache	1.3.6.1.4.1.2007.4.1.1.5.1.1.5	INTEGER	read-write	Router cache size. Default value is 64.
INT telProdNpIPGloDirectBroadcast	1.3.6.1.4.1.2007.4.1.1.5.1.1.6	INTEGER	read-write	Direct broadcast activation. Default value of the device is yes(1).
INT telProdNpIPGloMultiwayPaquet	1.3.6.1.4.1.2007.4.1.1.5.1.1.7	INTEGER	read-write	Multipath activation: (1) Per packet multipath, round-robin strategy. (2) Multipath dissabled. (3) Per source and destination multipath (session). (4) Per packet multipath, relative-weights strategy. Default value is disabled(2).
INT telProdNpIPGloHabAccessControl	1.3.6.1.4.1.2007.4.1.1.5.1.1.8	INTEGER	read-write	Access controls activation. If they are disabled, telProdNpIPCtrlTable table does not exist. Default value of the device is NO(2).
INT telProdNpIPDelAllDir	1.3.6.1.4.1.2007.4.1.1.5.1.1.9	INTEGER	read-write	This variable deletes all rows of the IP addresses table (telProdNpIPDirTable).
INT telProdNpIPDelAllRut	1.3.6.1.4.1.2007.4.1.1.5.1.1.10	INTEGER	read-write	This variable deletes all rows of the IP routes table (telProdNpIPRutTable).
INT telProdNpIPDelAllFil	1.3.6.1.4.1.2007.4.1.1.5.1.1.11	INTEGER	read-write	This variable deletes all rows of the filters table (telProdNpIPFilTable).
INT telProdNpIPDelAllCtl	1.3.6.1.4.1.2007.4.1.1.5.1.1.12	INTEGER	read-write	This variable deletes all rows of the access-controls table (telProdNpIPCtrlTable).
INT telProdNpIPGloHabIPClassless	1.3.6.1.4.1.2007.4.1.1.5.1.1.15	INTEGER	read-write	This variable allows enabling IP Classless. Default value of the device is NO(2).
IP telProdNpIPGloDirIPManagement	1.3.6.1.4.1.2007.4.1.1.5.1.1.16	IpAddress	read-write	Management IP address for traps.
telProdNpIPDirTable	1.3.6.1.4.1.2007.4.1.1.5.1.2		not-accessible	Addresses list. There are two table indexes: the interface and the IP address index.
telProdNpIPDirEntry	1.3.6.1.4.1.2007.4.1.1.5.1.2.1		not-accessible	Each entry consists of the addresses, the interface number (first address), the IP address index (second index), the table control variable, the IP address, the mask associated to that IP address, the broadcast type and the broadcast stuffing of that IP address.
INT telProdNpIPDirInterfazIndex	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.1	INTEGER	read-only	Interface number associated to that IP address. It is the first table index. The interfaces of the ROUTER part (from the first (LAN) till Router->Node) are the only possible ones.
INT telProdNpIPDirIndex	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.2	INTEGER	read-only	Entry number of the IP address. It is the second table index.
INT telProdNpIPDirStatus	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.3	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 adds a new row (IP address) in the table with the default values, and returns 2. If it already existed, it modifies IP address as it is described in the following variable(telProdNpIPDirIP). The new row must be added immediately after the last index. Set to 3 deletes all the table fields corresponding to the index, and returns 3. Get returns 1 if the address exists.
IP telProdNpIPDirIP	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.4	IpAddress	read-write	IP address of this entry. If it is the first interface (number 1, LAN), default value is 0.0.0.0. If it is another interface, default value is 0.0.0.(interface number). If it is requested a new row for an interface to which a row whith the default values already has been assigned, then default IP address will be 0.0.0.(number), where number is the highest interface number (which can have IP address) + 1. And if this IP address already exists, the following one to the last one which exists will be assigned to the interface (adding 1 to the fourth byte). If it is tried to realize a SET with an existing address in another interface, then it returns ERROR. It is allowed realizing a SET with the same address. If it is realized a SET to an address whose first byte is zero, then it only allows the 0.0.0.(number) format, where number is just like before. If the address first byte is zero, then the mask is 0.0.0.0.
IP telProdNpIPDirMascara	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.5	IpAddress	read-write	Mask associated to this IP address. If it is realized a SET to this variable, and the associate IP address has the first byte to zero, then the mask can only be 0.0.0.0. In another case, it returns ERROR. If IP address starts at zero, then default value will be 0.0.0.0. If it isn't so, then default value will be 255.0.0.0.
INT telProdNpIPDirBroadcastType	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.6	INTEGER	read-write	Broadcast type. Default value is net (1).
INT telProdNpIPDirBroadcastRell	1.3.6.1.4.1.2007.4.1.1.5.1.2.1.7	INTEGER	read-write	Broadcast stuffing. Value 0 shows that it is stuffed with zeros. Value 1 shows that it is stuffed with zeros. Default value is 0.
telProdNpIPRutTable	1.3.6.1.4.1.2007.4.1.1.5.1.4		not-accessible	Routes list. The table index is the route position.
telProdNpIPRutEntry	1.3.6.1.4.1.2007.4.1.1.5.1.4.1		not-accessible	Each entry consists of the routes, the route number (table index), the table control variable, the ending IP address, the mask associated to that IP address, the following IP address, the mask associated to to that IP address and the cost.
INT telProdNpIPRutIndex	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.1	INTEGER	read-only	It is the route position in the table.
INT telProdNpIPRutStatus	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.2	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 adds a new row (route) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that route, and returns 3. Get returns 1 if the route exists.
IP telProdNpIPRutDirIPFinal	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.3	IpAddress	read-write	Destination IP address. If address is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask.) Default value is 0.0.0.0.
IP telProdNpIPRutMascara	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.4	IpAddress	read-write	Mask associated to this IP address. If the mask is repeated, then it returns error (it must be repeated the IP address and the corresponding mask.) Default value is 0.0.0.0.
IP telProdNpIPRutDirIPNext	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.5	IpAddress	read-write	IP address of the next hop. Default value is 0.0.0.0.
INT telProdNpIPRutCost	1.3.6.1.4.1.2007.4.1.1.5.1.4.1.6	INTEGER	read-write	Hops cost. Default value is 1.
telProdNpIPCtrlTable	1.3.6.1.4.1.2007.4.1.1.5.1.5		not-accessible	Access control list. The table index is the access control position.
telProdNpIPCtrlEntry	1.3.6.1.4.1.2007.4.1.1.5.1.5.1		not-accessible	Each entry consists of the access controls information: the access control number (table index), the table control variable, the priority, the access type, the source IP address, the mask associated to source IP address, the destination IP address, the mask associated to destination IP address, the starting protocol, the ending protocol, the starting port and the ending port.
INT telProdNpIPCtrlIndex	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.1	INTEGER	read-only	It is the access control position in the table.
INT telProdNpIPCtrlStatus	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.2	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 adds a new row (access control) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that access control, and returns 3. Get returns 1 if the control exists.
INT telProdNpIPCtrlPriority	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.3	INTEGER	read-write	Access control priority. It coincides with its position in the table. Default value is 1. When realizing a set, the position behind which the access control will be placed, must be indicated.
INT telProdNpIPCtrlAccessType	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.4	INTEGER	read-write	Access control type. Default value is 1 (inclusive).
IP telProdNpIPCtrlDirIPOrigin	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.5	IpAddress	read-write	Source IP address. Default value is 0.0.0.0. If the address is repeated, then it returns error.
IP telProdNpIPCtrlMasIPOrigin	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.6	IpAddress	read-write	Mask associated to source IP address. If this condition is not fulfilled, SourceIPAddress & (~(SourceMask) )=0, then the mask is inconsistent. Default value is 0.0.0.0.
IP telProdNpIPCtrlDirIPFinal	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.7	IpAddress	read-write	Destination IP address. Default value is 0.0.0.0. If the address is repeated, then it returns error.
IP telProdNpIPCtrlMasIPFinal	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.8	IpAddress	read-write	Mask associated to destination IP address. If this condition is not fulfilled, DestinationIPAddress & (~(DestinationMask) )=0, then the mask is inconsistent. Default value is 0.0.0.0.
INT telProdNpIPCtrlProtStart	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.9	INTEGER	read-write	Starting protocol. If it is tried to introduce a value higher than telProdNpIPCtrlProtEnd, then it returns error. Default value is 0.
INT telProdNpIPCtrlProtEnd	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.10	INTEGER	read-write	Ending protocol. If it is tried to introduce a value lower than telProdNpIPCtrlProtStart, then it returns error. Default value is 255.
INT telProdNpIPCtrlPortStart	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.11	INTEGER	read-write	Starting destination port for UDP or TCP protocol and starting code for ICMP protocol. If it is tried to introduce a value higher than telProdNpIPCtrlPortEnd, then it returns error. Default value is 0.
INT telProdNpIPCtrlPortEnd	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.12	INTEGER	read-write	Ending destination port for UDP or TCP protocol and ending code for ICMP protocol. If it is tried to introduce a value lower than telProdNpIPCtrlPortStart, then it returns error. Default value is 65535.
INT telProdNpIPCtrlSrcPortStart	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.13	INTEGER	read-write	Starting source port for UDP or TCP protocol and starting type for ICMP protocol. If it is tried to introduce a value higher than telProdNpIPCtrlSrcPortEnd, then it returns error. Default value is 0.
INT telProdNpIPCtrlSrcPortEnd	1.3.6.1.4.1.2007.4.1.1.5.1.5.1.14	INTEGER	read-write	Ending source port for UDP or TCP protocol and endng type for ICMP protocol. If it is tried to introduce a value lower than telProdNpIPCtrlSrcPortStart, then it returns error. Default value is 65535.
telProdNpIPFilTable	1.3.6.1.4.1.2007.4.1.1.5.1.6		not-accessible	Filters list. The table index is the filter position.
telProdNpIPFilEntry	1.3.6.1.4.1.2007.4.1.1.5.1.6.1		not-accessible	Each entry consists of the filters, the filter number (table index), the table control variable, the destination IP address and the mask associated to that IP address.
INT telProdNpIPFilIndex	1.3.6.1.4.1.2007.4.1.1.5.1.6.1.1	INTEGER	read-only	It is the filter position in the table.
INT telProdNpIPFilStatus	1.3.6.1.4.1.2007.4.1.1.5.1.6.1.2	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 adds a new row (filter) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that filter, and returns 3. Get returns 1 if the filter exists.
IP telProdNpIPFilDirIPFinal	1.3.6.1.4.1.2007.4.1.1.5.1.6.1.3	IpAddress	read-write	Destination IP address. Default value is 0.0.0.0. If address is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask).
IP telProdNpIPFilMasIPNet	1.3.6.1.4.1.2007.4.1.1.5.1.6.1.4	IpAddress	read-write	Mask associated to this IP address. If mask is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask). Default value is 0.0.0.0.
telProdNpIPAggRutTable	1.3.6.1.4.1.2007.4.1.1.5.1.8		not-accessible	Aggregation routes table. The table index is the route position.
telProdNpIPAggRutEntry	1.3.6.1.4.1.2007.4.1.1.5.1.8.1		not-accessible	Each entry consists of the routes, the route number (table index), the table control variable, the ending IP address, the mask associated to that IP address and the cost.
INT telProdNpIPAggRutIndex	1.3.6.1.4.1.2007.4.1.1.5.1.8.1.1	INTEGER	read-only	It is the route position in the table.
INT telProdNpIPAggRutStatus	1.3.6.1.4.1.2007.4.1.1.5.1.8.1.2	INTEGER	read-write	Table control variable. Set to 1 does nothing. Set to 2 deletes that route. Get returns 1 if the route exists.
IP telProdNpIPAggRutDirIPFinal	1.3.6.1.4.1.2007.4.1.1.5.1.8.1.3	IpAddress	read-write	Destination IP address. To introduce a new aggregation route, a SET operation must be carried out, giving this variable a certain value (IP address). The index corresponding to this address must be higher than the entries number of that table. Default value is 0.0.0.0.
IP telProdNpIPAggRutMascara	1.3.6.1.4.1.2007.4.1.1.5.1.8.1.4	IpAddress	read-write	Mask associated to this IP address. To introduce a new aggregation route, a SET operation must be carried out, giving this variable a certain value (mask). The index corresponding to this address must be higher than the entries number of that table. Default value is 0.0.0.0.
INT telProdNpIPAggRutCost	1.3.6.1.4.1.2007.4.1.1.5.1.8.1.5	INTEGER	read-only	Hops cost. Default value is 1.

RFC description

Teldat private MIB for IP protocol configuration including routing table and gateway settings.

Start monitoring Teldat router/branch-office CPE router (IP addressing/routing config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-CFG-PROTOCOL-IP-MIB

What Is TELDAT-CFG-PROTOCOL-IP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description