| OID symbolic | OID numeric | Type | Access | Description |
|---|
| INT fddiRingUtilization | 1.3.6.1.4.1.81.27.6.10 | INTEGER | read-only | A utilization of the FDDI ring, attached to the LSF100 modules (or other members in the family). |
| CTR macCopiedFrames | 1.3.6.1.4.1.81.27.6.3 | Counter | read-only | A count of the number of frames addressed to and
successfully copied into the station's receive
buffers by this MAC. This count does not include
MAC frames. |
| CTR macErrFrames | 1.3.6.1.4.1.81.27.6.6 | Counter | read-only | A count of the number of frames that were detected
in error by this MAC that had not been detected
in error by another MAC. |
| CTR macInFrames | 1.3.6.1.4.1.81.27.6.2 | Counter | read-only | A count of the number of frames received by this MAC. |
| CTR macLostFrames | 1.3.6.1.4.1.81.27.6.7 | Counter | read-only | A count of the number of instances that this MAC
detected a format error during frame reception, such
that the frame was stripped. |
| CTR macNotCopiedFrames | 1.3.6.1.4.1.81.27.6.8 | Counter | read-only | A count of the number of frames addressed to this MAC
but were not copied into the station's receive buffers.
This count does not include MAC frames. |
| CTR macOutFrames | 1.3.6.1.4.1.81.27.6.4 | Counter | read-only | A count of the number of frames trasmitted by this MAC.
This count does not include MAC frames. |
| CTR macRingOpState | 1.3.6.1.4.1.81.27.6.9 | Counter | read-only | A count of the number of times the ring has entered
the Ring Operational state from the Ring Not Operational
state. |
| CTR macTokenRcvd | 1.3.6.1.4.1.81.27.6.5 | Counter | read-only | A count of the number of times the station has received
a token on this MAC. |
| INT smartAgCommDebugMode | 1.3.6.1.4.1.81.27.2.2 | INTEGER | read-write | Attribute describing the agent mode in
which communication problem traps are
sent to managers (value 'on') or are not
sent to managers (value 'off'). |
| INT smartAgConfigChangeTraps | 1.3.6.1.4.1.81.27.2.3 | INTEGER | read-write | The value of this attributes
determines whether or not the agent
sends Configuration Change traps
to the manager. |
| INT smartAgCoprocCommStatus | 1.3.6.1.4.1.81.27.2.1 | INTEGER | read-only | Attribute describing the status of the
communication between the
agent and its coprocessor. |
| smartAgent | 1.3.6.1.4.1.81.27.2 | | | |
| INT smartAgFaultTraps | 1.3.6.1.4.1.81.27.2.4 | INTEGER | read-write | The value of this attributes determines
whether or not the agent
sends Fault traps to the manager. |
| INT smartAgLaneFaultTraps | 1.3.6.1.4.1.81.27.2.5 | INTEGER | read-write | The value of this attributes determines
whether or not the agent
sends Fault traps when it cannot connect to some
ELAN to the manager. |
| INT smartAgSoftwareStatus | 1.3.6.1.4.1.81.27.2.6 | INTEGER | read-write | Describes configuration of the firmware on this agent.
unLoadable(1) - is returned by agents which do not support the Software
Download feature;
loaded(2) - is returned by agents with loaded software;
downLoading(3) - when the attribute is set to this value by manager,
it triggers the Software Download procedure. When procedure finished,
agent software will reestablish value 'loaded(2)'.
downLoadOfDownload (4) - when the attribute is set to this value by manager,
it causes the Agent to download the new download software.
When procedure finished, agent software will reestablish value 'loaded(2)'. |
| smartDevices | 1.3.6.1.4.1.81.27 | | | |
| smartFatherHub | 1.3.6.1.4.1.81.27.5 | | | |
| OCT smartFatherMacList | 1.3.6.1.4.1.81.27.5.2 | OCTET STRING | read-only | This variable is the list of Mac Addresses of
the box agent. |
| INT smartFatherNumberOfMac | 1.3.6.1.4.1.81.27.5.1 | INTEGER | read-only | Number of MAC Addresses of the box agent. |
| STR smartGenBootVersion | 1.3.6.1.4.1.81.27.1.4 | DisplayString | read-only | ASCII string for description and display of the smart device boot software version. |
| INT smartGenConnectMode | 1.3.6.1.4.1.81.27.1.12 | INTEGER | read-write | Enables the user to configure the ATM interface of the smart device to work in front another ATM
port of a smart device: pvc or in front a switch with lane10. |
| smartGeneral | 1.3.6.1.4.1.81.27.1 | | | |
| STR smartGenHardwareVersion | 1.3.6.1.4.1.81.27.1.6 | DisplayString | read-only | ASCII string for description and
display of the agent hardware version. |
| OCT smartGenHubAddr | 1.3.6.1.4.1.81.27.1.17 | OCTET STRING | read-write | This attribute defines an unique address by which the agent may be
addressed by the management console. The address format should be
consistent with the type defined by chAgHubMgmtIfType. |
| INT smartGenHubMgmtIfType | 1.3.6.1.4.1.81.27.1.16 | INTEGER | read-only | This attribute describes one of the interfaces of agents existing on
modules and their type. Value 'none' defines the lack of an
interface whose type is recognized by the management console.
Any other value defines an interface whose type is recognized by
the management console and may be used as a management channel. |
| TIK smartGenLastChange | 1.3.6.1.4.1.81.27.1.9 | TimeTicks | read-only | This attribute contains the value of sysUpTime
at the time any change pertaining to the device:
The changes are regarding the parameters of this
group and any parameters of smartIfExtensionTable. |
| INT smartGenMonitoredPort | 1.3.6.1.4.1.81.27.1.8 | INTEGER | read-write | Value '0' is illegal when Monitor Mode is on. |
| INT smartGenMonitoringPort | 1.3.6.1.4.1.81.27.1.7 | INTEGER | read-only | Enables a user to fix one port to monitor
other segment ports. For the moment,
the monitoring port is port 16.
In this case, this port doesn't participate to
any other functions of the device. |
| INT smartGenMonitorMode | 1.3.6.1.4.1.81.27.1.10 | INTEGER | read-write | Activates the monitor function. |
| OCT smartGenNetworkPrefix | 1.3.6.1.4.1.81.27.1.11 | OCTET STRING | read-write | For ATM devices, the prefix of the switch connected. |
| STR smartGenOSVersion | 1.3.6.1.4.1.81.27.1.2 | DisplayString | read-only | ASCII string for description and display of the smart device operating system (kernel) version. |
| INT smartGenPvcVC | 1.3.6.1.4.1.81.27.1.14 | INTEGER | read-only | When the smart device is in mode pvc, the VC on which the data is runing. |
| INT smartGenPvcVP | 1.3.6.1.4.1.81.27.1.13 | INTEGER | read-only | When the smart device is in mode pvc,
the VP on which the data is runing. |
| INT smartGenReset | 1.3.6.1.4.1.81.27.1.5 | INTEGER | read-write | Setting the value of this attribute to ON is interpreted as a reset
command for the whole device. It initiates a complete re-initialization of the device. |
| INT smartGenSlotNumber | 1.3.6.1.4.1.81.27.1.15 | INTEGER | read-only | Identifies the location (slot number) of the device in the chassis. The first slot is 1 |
| STR smartGenSoftwareDscr | 1.3.6.1.4.1.81.27.1.3 | DisplayString | read-only | ASCII string for description and display of the smart device software information. |
| STR smartGenSWVersion | 1.3.6.1.4.1.81.27.1.1 | DisplayString | read-only | ASCII string for description and display of the smart device software version. |
| smartIfExtension | 1.3.6.1.4.1.81.27.3 | | | |
| INT smartIfExtensionActivity | 1.3.6.1.4.1.81.27.3.1.1.2 | INTEGER | read-write | Valid for ATM Type supporting redundancy. |
| INT smartIfExtensionBackPressure | 1.3.6.1.4.1.81.27.3.1.1.6 | INTEGER | read-write | Enables a user to disable the backpressure
mechanism. |
| INT smartIfExtensionBridgeEnable | 1.3.6.1.4.1.81.27.3.1.1.5 | INTEGER | read-only | Valid for Ethernet port when in sniffer mode. |
| smartIfExtensionEntry | 1.3.6.1.4.1.81.27.3.1.1 | | not-accessible | Additional information |
| INT smartIfExtensionEthStatus | 1.3.6.1.4.1.81.27.3.1.1.1 | INTEGER | read-only | Valid for Ethernet Type only |
| INT smartIfExtensionPriorityLevel | 1.3.6.1.4.1.81.27.3.1.1.4 | INTEGER | read-write | This attribute defines the priority levels of Ethernet ports.
The highest priority is video. |
| INT smartIfExtensionSTAEnable | 1.3.6.1.4.1.81.27.3.1.1.7 | INTEGER | read-write | Allows user to take out a port from the STA. |
| smartIfExtensionTable | 1.3.6.1.4.1.81.27.3.1 | | not-accessible | This table contains additional information concerning physical
interfaces. (Ethernet and ATM ports.) |
| INT smartIfExtensionViNet | 1.3.6.1.4.1.81.27.3.1.1.3 | INTEGER | read-write | Virtual Net Number.
Value '0' for generic mode.
The value for not supported is 511. |
| smartLSFddi | 1.3.6.1.4.1.81.27.6 | | | |
| smartLSFEntry | 1.3.6.1.4.1.81.27.6.1.1 | | not-accessible | A table entry containing MAC addresses of all LSF100
modules on the FDDI ring. |
| INT smartLSFEntryStatus | 1.3.6.1.4.1.81.27.6.1.1.2 | INTEGER | read-only | Only the status active(1) is relevant to this table. |
| OCT smartLSFMACAddr | 1.3.6.1.4.1.81.27.6.1.1.1 | OCTET STRING | read-only | This item defines the MAC address
of an LSF100 connected to the FDDI ring. |
| smartLSFTable | 1.3.6.1.4.1.81.27.6.1 | | not-accessible | This table contains the MAC addresses of all LSF100
modules on the FDDI ring.
This information is needed for LANNET Topology application. |
| smartViNet | 1.3.6.1.4.1.81.27.4 | | | |
| INT smartViNetConsoleManagement | 1.3.6.1.4.1.81.27.4.7 | INTEGER | read-write | The ViNet to which the console
belongs to. |
| INT smartViNetCurrentBridge | 1.3.6.1.4.1.81.27.4.2 | INTEGER | read-write | ViNet that is the current owner
of the STA group, and forwarding table
in the bridge MIB. |
| INT smartViNetElanAssociation | 1.3.6.1.4.1.81.27.4.4.1.1 | INTEGER | read-write | The association number. For the first
association, this entry is read-only. |
| smartViNetElanEntry | 1.3.6.1.4.1.81.27.4.4.1 | | not-accessible | Each Virtual Net will be associated to an
ELAN. The vinet = 0 is the first entry of the
device. |
| INT smartViNetElanEntryStatus | 1.3.6.1.4.1.81.27.4.4.1.4 | INTEGER | read-write | The status of the entry. When the console starts
to set the parameters of the row, the agent sets the status to notReady.
The status createAndWait is set by the console,
when the row is complete. After reset of the device, the row
is 'active(1)'.
When the console has to
delete a row, it sets the status to 'destroy'. After reset,
the row should disappear. |
| INT smartViNetElanIfIndex | 1.3.6.1.4.1.81.27.4.4.1.5 | INTEGER | read-only | Creating a row in this table causes the agent to add
one row in the interface table. Before setting the row status to
active, the agent fill this field with the value of the ifIndex of the
new created row. |
| STR smartViNetElanName | 1.3.6.1.4.1.81.27.4.4.1.3 | DisplayString | read-write | The ELAN name. For the first row,
this entry is 'default' and is read-only. |
| smartViNetElanTable | 1.3.6.1.4.1.81.27.4.4 | | not-accessible | This table contains all the information
concerning the association between virtual nets
and ELAN name. |
| INT smartViNetElanViNet | 1.3.6.1.4.1.81.27.4.4.1.2 | INTEGER | read-write | The virtual net number. For the first
row, this entry is read-only. |
| smartViNetEntry | 1.3.6.1.4.1.81.27.4.3.1 | | not-accessible | Each Virtual Net will be an isolated entity.
The first row of this table is the generic
virtual net and is read-only. |
| MAC smartViNetFdbAddress | 1.3.6.1.4.1.81.27.4.5.1.2 | MacAddress | read-only | A unicast MAC address for which the bridge has
forwarding and/or filtering information. |
| smartViNetFdbEntry | 1.3.6.1.4.1.81.27.4.5.1 | | not-accessible | The forwarding tables. The
smartViNetFdbPlusOne = 1 corresponds to
ViNet generic. |
| INT smartViNetFdbPlusOne | 1.3.6.1.4.1.81.27.4.5.1.1 | INTEGER | read-only | This table is indexed by the
virtual net number plus 1,
since the first group is '0'. |
| INT smartViNetFdbPort | 1.3.6.1.4.1.81.27.4.5.1.3 | INTEGER | read-only | Either the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of dot1dTpFdbAddress has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address (e.g. in the dot1dStaticTable).
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
dot1dTpFdbStatus is not learned(3). |
| INT smartViNetFdbStatus | 1.3.6.1.4.1.81.27.4.5.1.4 | INTEGER | read-only | see dot1dTpFdbStatus. |
| smartViNetFdbTable | 1.3.6.1.4.1.81.27.4.5 | | not-accessible | This table is the forwarding table per virtual net. |
| INT smartViNetMaxNumOfNets | 1.3.6.1.4.1.81.27.4.1 | INTEGER | read-only | Maximum number of local ViNets supported. |
| INT smartViNetNumberPlusOne | 1.3.6.1.4.1.81.27.4.3.1.1 | INTEGER | read-write | Correspondance for Virtual Net:
ViNet: zero is 'generic' |
| INT smartViNetNumOfMembers | 1.3.6.1.4.1.81.27.4.3.1.2 | INTEGER | read-only | Number of members. |
| TIM smartViNetStpBridgeForwardDelay | 1.3.6.1.4.1.81.27.4.6.1.14 | Timeout | read-write | |
| TIM smartViNetStpBridgeHelloTime | 1.3.6.1.4.1.81.27.4.6.1.13 | Timeout | read-write | The value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by
802.1d/D9 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds. |
| TIM smartViNetStpBridgeMaxAge | 1.3.6.1.4.1.81.27.4.6.1.12 | Timeout | read-write | |
| OCT smartViNetStpDesignatedRoot | 1.3.6.1.4.1.81.27.4.6.1.5 | OCTET STRING | read-only | The bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node. |
| smartViNetStpEntry | 1.3.6.1.4.1.81.27.4.6.1 | | not-accessible | The bridge will function between each of those entries. |
| TIM smartViNetStpForwardDelay | 1.3.6.1.4.1.81.27.4.6.1.11 | Timeout | read-only | |
| TIM smartViNetStpHelloTime | 1.3.6.1.4.1.81.27.4.6.1.9 | Timeout | read-only | The amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using. |
| INT smartViNetStpHoldTime | 1.3.6.1.4.1.81.27.4.6.1.10 | INTEGER | read-only | This time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second. |
| TIK smartViNetStpLastChange | 1.3.6.1.4.1.81.27.4.6.1.15 | TimeTicks | read-only | This attribute contains the value of sysUpTime
at the time any change pertaining to the
specified STA occurred. |
| TIM smartViNetStpMaxAge | 1.3.6.1.4.1.81.27.4.6.1.8 | Timeout | read-only | The maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using. |
| INT smartViNetStpPlusOne | 1.3.6.1.4.1.81.27.4.6.1.1 | INTEGER | read-only | This table is indexed by the
virtual net number plus 1,
since the first group is '0'. |
| INT smartViNetStpPriority | 1.3.6.1.4.1.81.27.4.6.1.2 | INTEGER | read-write | |
| INT smartViNetStpRootCost | 1.3.6.1.4.1.81.27.4.6.1.6 | INTEGER | read-only | The cost of the path to the root as seen from
this bridge. |
| INT smartViNetStpRootPort | 1.3.6.1.4.1.81.27.4.6.1.7 | INTEGER | read-only | The port number of the port which offers the
lowest cost path from this bridge to the root
bridge. |
| smartViNetStpTable | 1.3.6.1.4.1.81.27.4.6 | | not-accessible | This table contains all the information concerning the
STA parameters per group. |
| TIK smartViNetStpTimeSinceTopologyChange | 1.3.6.1.4.1.81.27.4.6.1.3 | TimeTicks | read-only | The time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity. |
| CTR smartViNetStpTopChanges | 1.3.6.1.4.1.81.27.4.6.1.4 | Counter | read-only | The total number of topology changes detected by
this bridge since the management entity was last
reset or initialized. |
| smartViNetTable | 1.3.6.1.4.1.81.27.4.3 | | not-accessible | This table contains the number of members
belonging to each virtual nets . |
