SLE-NETWORK-MIB

All MIBs › SLE-NETWORK-MIB

Organization: HANASOFT

Last Updated: 2004-12-29

Category: DASAN Networks SLE OLT Management

Description: Manages Hanasoft SLE OLT network layer configuration including IP interfaces and static routing.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SLE-NETWORK-MIB?

This is a Hanasoft private enterprise MIB for the SLE line of GPON/EPON Optical Line Terminal (OLT) systems, covering IP network-layer configuration such as management interfaces, static routing, and DHCP relay/server behavior. It exposes configuration objects for IP interface addressing, static route entries, and DHCP-related parameters used by the OLT's management plane. As primarily a network-configuration MIB it does not directly expose hardware sensors, but verifying its IP/DHCP/route configuration is important to confirming the OLT's management-plane software is reachable and correctly provisioned, a prerequisite for monitoring anything else on the device. It works alongside Hanasoft's other SLE MIBs (chassis, PON port, ONU management) that depend on this network layer being correctly configured for SNMP reachability itself. It is deployed on Hanasoft SLE-series OLTs in FTTH/PON access-network head-end locations, and technicians can obtain an SLE-NETWORK-MIB download to load the module into their network management system.

IPNetwork Monitor allows you to monitor SNMP objects defined in SLE-NETWORK-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Hanasoft SLE-series GPON/EPON Optical Line Terminal

Monitoring Examples

No sample_objects were provided; consistent with the module description covering DHCP and IP network features, a realistic use would be checking the OLT's configured management IP interface and static route table, and confirming DHCP relay/server settings are correctly pointed at the intended server, since a misconfiguration here would make the OLT unreachable for all other SNMP-based monitoring.

What Can Be Monitored

management IP interface configuration
static route table entries
DHCP relay/server configuration

Imported Objects

From DASAN-SMI

sleMgmt

OBJECT-IDENTITY

From IANAifType-MIB

IANAtunnelType

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SLE-TC-MIB

SleControlRequestResultType
SleControlStatusType

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

BITS
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

MacAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
sleNetwork	1.3.6.1.4.1.6296.101.11			This MIB contains all needed informations about DHCP and all supported sle DHCP features.
sleNetInterface	1.3.6.1.4.1.6296.101.11.1
sleNetIfTable	1.3.6.1.4.1.6296.101.11.1.1		not-accessible	Description.
sleNetIfEntry	1.3.6.1.4.1.6296.101.11.1.1.1		not-accessible	Description.
I32 sleNetIfIndex	1.3.6.1.4.1.6296.101.11.1.1.1.1	Integer32	read-only	Network interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface index
OCT sleNetIfName	1.3.6.1.4.1.6296.101.11.1.1.1.2	OCTET STRING	read-only	Device Name of this Interface.
OCT sleNetIfDescription	1.3.6.1.4.1.6296.101.11.1.1.1.3	OCTET STRING	read-only	Description of this interface.
NUM sleNetIfTableIndex	1.3.6.1.4.1.6296.101.11.1.1.1.4	InterfaceIndex	read-only	Same as ifIndex (for appropriated ifTable entries).
INT sleNetIfRegState	1.3.6.1.4.1.6296.101.11.1.1.1.5	INTEGER	read-only	Registered state of Network device.
INT sleNetIfAdminState	1.3.6.1.4.1.6296.101.11.1.1.1.6	INTEGER	read-only	Administrative state. down - shutdown up - noshutdown
INT sleNetIfOperState	1.3.6.1.4.1.6296.101.11.1.1.1.7	INTEGER	read-only	Operational state. down - shutdown or not running up - running
INT sleNetIfMulticast	1.3.6.1.4.1.6296.101.11.1.1.1.8	INTEGER	read-only	Multicast enable/disable state.
INT sleNetIfMtu	1.3.6.1.4.1.6296.101.11.1.1.1.9	INTEGER	read-only	Maximum Transmission Unit.
INT sleNetIfIpSetMode	1.3.6.1.4.1.6296.101.11.1.1.1.10	INTEGER	read-only	IP address setting mode. 0 : static 1 : dynamic (by DHCP client)
INT sleNetIfIpMartianFilter	1.3.6.1.4.1.6296.101.11.1.1.1.11	INTEGER	read-only	Description.
I32 sleNetIfUpCnt	1.3.6.1.4.1.6296.101.11.1.1.1.12	Integer32	read-only	The times of link-up event.
I32 sleNetIfDownCnt	1.3.6.1.4.1.6296.101.11.1.1.1.13	Integer32	read-only	The times of link-down event.
C64 sleNetIfLinkUpTime	1.3.6.1.4.1.6296.101.11.1.1.1.14	Counter64	read-only	The elapsed time after link is up.
C64 sleNetIfElapsedTimeAfterClearStats	1.3.6.1.4.1.6296.101.11.1.1.1.15	Counter64	read-only	The elapsed time after clearing status.
OCT sleNetIfBindingVRFName	1.3.6.1.4.1.6296.101.11.1.1.1.16	OCTET STRING	read-only	VRF name that this tunnel interface is binding.
INT sleNetIfOnFailUseVRF	1.3.6.1.4.1.6296.101.11.1.1.1.17	INTEGER	read-only	Lookup into a global routing table when the VRF routing table lookup was failed.
INT sleNetIfIpUnreachability	1.3.6.1.4.1.6296.101.11.1.1.1.18	INTEGER	read-only	IP unreachability ON/OFF
INT sleNetIfipRedirects	1.3.6.1.4.1.6296.101.11.1.1.1.19	INTEGER	read-only	Description.
INT sleNetIfIpForwarding	1.3.6.1.4.1.6296.101.11.1.1.1.20	INTEGER	read-only	The IP forwarding status
OCT sleNetIfAlias	1.3.6.1.4.1.6296.101.11.1.1.1.21	OCTET STRING	read-only	lias Name for the Interface
INT sleNetIfIpArpAlias	1.3.6.1.4.1.6296.101.11.1.1.1.22	INTEGER	read-only	IP Arp Alias state
MAC sleNetIfIpArpAliasMac	1.3.6.1.4.1.6296.101.11.1.1.1.23	MacAddress	read-only	IP Arp Alias MAC
I32 sleNetIfArpMCProbeCount	1.3.6.1.4.1.6296.101.11.1.1.1.24	Integer32	read-only	ARP request Multicast probe count
I32 sleNetIfArpUCProbeCount	1.3.6.1.4.1.6296.101.11.1.1.1.25	Integer32	read-only	ARP request Unicast probe count
I32 sleNetIfArpRetransTime	1.3.6.1.4.1.6296.101.11.1.1.1.26	Integer32	read-only	Retrans time of ARP request (unit: 1s)
INT sleNetIfIpProxyArp	1.3.6.1.4.1.6296.101.11.1.1.1.27	INTEGER	read-only	IP Proxy Arp state
INT sleNetIfIpRPFilter	1.3.6.1.4.1.6296.101.11.1.1.1.28	INTEGER	read-only	IP Reverse Path Filtering of CPU
INT sleNetIfRPFilter	1.3.6.1.4.1.6296.101.11.1.1.1.29	INTEGER	read-only	Reverse Path Filtering of CHIP (default : looseAllow)
OCT sleNetIfRouteMap	1.3.6.1.4.1.6296.101.11.1.1.1.30	OCTET STRING	read-only	IP Policy route-map name
sleNetIfControl	1.3.6.1.4.1.6296.101.11.1.2
INT sleNetIfControlRequest	1.3.6.1.4.1.6296.101.11.1.2.1	INTEGER	read-write	The request of a user command.
SLE sleNetIfControlStatus	1.3.6.1.4.1.6296.101.11.1.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleNetIfControlTimer	1.3.6.1.4.1.6296.101.11.1.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleNetIfControlTimeStamp	1.3.6.1.4.1.6296.101.11.1.2.4	SleControlRequestResultType	read-only	The time stamp of the last command (end of command).
TIK sleNetIfControlReqResult	1.3.6.1.4.1.6296.101.11.1.2.5	TimeTicks	read-only	The result of the last user command.
I32 sleNetIfControlIndex	1.3.6.1.4.1.6296.101.11.1.2.6	Integer32	read-write	Network interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface index
OCT sleNetIfControlDescription	1.3.6.1.4.1.6296.101.11.1.2.7	OCTET STRING	read-write	Description of this interface.
INT sleNetIfControlRegState	1.3.6.1.4.1.6296.101.11.1.2.8	INTEGER	read-write	Description.
INT sleNetIfControlAdminState	1.3.6.1.4.1.6296.101.11.1.2.9	INTEGER	read-write	Administrative state.
INT sleNetIfControlMulticast	1.3.6.1.4.1.6296.101.11.1.2.10	INTEGER	read-write	Multicast enable/disable state.
INT sleNetIfControlMtu	1.3.6.1.4.1.6296.101.11.1.2.11	INTEGER	read-write	Maximum Transmission Unit.
INT sleNetIfControlIpMartianFilter	1.3.6.1.4.1.6296.101.11.1.2.12	INTEGER	read-write	Description.
OCT sleNetIfControlBindingVRFName	1.3.6.1.4.1.6296.101.11.1.2.13	OCTET STRING	read-write	VRF name that this tunnel interface is binding.
INT sleNetIfControlOnFailUseVRF	1.3.6.1.4.1.6296.101.11.1.2.14	INTEGER	read-write	Lookup into a global routing table when the VRF routing table lookup was failed.
INT sleNetIfControlIpUnreachability	1.3.6.1.4.1.6296.101.11.1.2.15	INTEGER	read-write	IP unreachability ON/OFF
INT sleNetIfControlIpRedirects	1.3.6.1.4.1.6296.101.11.1.2.16	INTEGER	read-write	Description.
INT sleNetIfControlIpForwarding	1.3.6.1.4.1.6296.101.11.1.2.17	INTEGER	read-write	The IP forwarding status
OCT sleNetIfControlAlias	1.3.6.1.4.1.6296.101.11.1.2.18	OCTET STRING	read-write	Alias Name for the Interface
INT sleNetIfControlIpArpAlias	1.3.6.1.4.1.6296.101.11.1.2.19	INTEGER	read-write	IP Arp Alias state
MAC sleNetIfControlIpArpAliasMac	1.3.6.1.4.1.6296.101.11.1.2.20	MacAddress	read-write	IP Arp Alias MAC
I32 sleNetIfControlArpMCProbeCount	1.3.6.1.4.1.6296.101.11.1.2.21	Integer32	read-write	ARP request Multicast probe count
I32 sleNetIfControlArpUCProbeCount	1.3.6.1.4.1.6296.101.11.1.2.22	Integer32	read-write	ARP request Unicast probe count
I32 sleNetIfControlArpRetransTime	1.3.6.1.4.1.6296.101.11.1.2.23	Integer32	read-write	Retrans time of ARP request (unit: 1s)
INT sleNetIfControlIpProxyArp	1.3.6.1.4.1.6296.101.11.1.2.24	INTEGER	read-write	IP Proxy Arp state
INT sleNetIfControlIpRPFilter	1.3.6.1.4.1.6296.101.11.1.2.25	INTEGER	read-write	IP Reverse Path Filtering of CPU
INT sleNetIfControlRPFilter	1.3.6.1.4.1.6296.101.11.1.2.26	INTEGER	read-write	Reverse Path Filtering of CHIP (default : looseAllow)
OCT sleNetIfControlRouteMap	1.3.6.1.4.1.6296.101.11.1.2.27	OCTET STRING	read-write	IP Policy route-map name
sleNetIfNotification	1.3.6.1.4.1.6296.101.11.1.3
NTF sleNetIfRegStateChanged	1.3.6.1.4.1.6296.101.11.1.3.1			Description.
NTF sleNetIfProfileChanged	1.3.6.1.4.1.6296.101.11.1.3.2			setNetIfProfile.
NTF sleNetIfIpMartianFilterChanged	1.3.6.1.4.1.6296.101.11.1.3.3			Description.
NTF sleNetIfBindingVRFSet	1.3.6.1.4.1.6296.101.11.1.3.4			Description.
NTF sleNetIfBindingVRFUnset	1.3.6.1.4.1.6296.101.11.1.3.5			Description.
NTF sleNetIfIpOnFailUseVRFChanged	1.3.6.1.4.1.6296.101.11.1.3.6			Description.
NTF sleNetIfIpUnreachabilityChanged	1.3.6.1.4.1.6296.101.11.1.3.7			Description.
NTF sleNetIfIpRedirectsChanged	1.3.6.1.4.1.6296.101.11.1.3.8			Description.
NTF sleNetIfIpForwardingChanged	1.3.6.1.4.1.6296.101.11.1.3.9			setNetIfIpForwarding
NTF sleNetIfAliasChanged	1.3.6.1.4.1.6296.101.11.1.3.10			setAlias
NTF sleNetIfIpArpAliasChanged	1.3.6.1.4.1.6296.101.11.1.3.11			setIpArpAlias
NTF sleNetIfArpMCProbeCountChanged	1.3.6.1.4.1.6296.101.11.1.3.12			setArpMCProbeCount
NTF sleNetIfArpUCProbeCountChanged	1.3.6.1.4.1.6296.101.11.1.3.13			setArpUCProbeCount
NTF sleNetIfArpRetransTimeChanged	1.3.6.1.4.1.6296.101.11.1.3.14			setArpRetransTime
NTF sleNetIfIpProxyArpChanged	1.3.6.1.4.1.6296.101.11.1.3.15			setIpProxyArp
NTF sleNetIfIpRPFilterChanged	1.3.6.1.4.1.6296.101.11.1.3.16			setIpRPFilter
NTF sleNetIfRPFilterChanged	1.3.6.1.4.1.6296.101.11.1.3.17			setRPFilter
NTF sleNetIfRouteMapChanged	1.3.6.1.4.1.6296.101.11.1.3.18			setRouteMap
sleIpAddress	1.3.6.1.4.1.6296.101.11.2
sleIpAddrTable	1.3.6.1.4.1.6296.101.11.2.1		not-accessible	Description.
sleIpAddrEntry	1.3.6.1.4.1.6296.101.11.2.1.1		not-accessible	Description.
IP sleIpAddrValue	1.3.6.1.4.1.6296.101.11.2.1.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
I32 sleIpAddrMask	1.3.6.1.4.1.6296.101.11.2.1.1.2	Integer32	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
IP sleIpAddrBcast	1.3.6.1.4.1.6296.101.11.2.1.1.3	IpAddress	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
BIT sleIpAddrFlag	1.3.6.1.4.1.6296.101.11.2.1.1.4	Bits	read-only	Description.
INT sleIpAddrScope	1.3.6.1.4.1.6296.101.11.2.1.1.5	INTEGER	read-only	Description.
INT sleIpAddrIpIndex	1.3.6.1.4.1.6296.101.11.2.1.1.6	INTEGER	read-only	The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
INT sleIpAddrUnnumUsedIp	1.3.6.1.4.1.6296.101.11.2.1.1.7	INTEGER	read-only	The Check a specific IP address for using interface unnumbered feature.
sleIpAddrControl	1.3.6.1.4.1.6296.101.11.2.2
INT sleIpAddrControlRequest	1.3.6.1.4.1.6296.101.11.2.2.1	INTEGER	read-write	The request of a user command.
SLE sleIpAddrControlStatus	1.3.6.1.4.1.6296.101.11.2.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleIpAddrControlTimer	1.3.6.1.4.1.6296.101.11.2.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleIpAddrControlTimeStamp	1.3.6.1.4.1.6296.101.11.2.2.4	SleControlRequestResultType	read-only	The time stamp of the last command (end of command).
TIK sleIpAddrControlReqResult	1.3.6.1.4.1.6296.101.11.2.2.5	TimeTicks	read-only	The result of the last user command.
I32 sleIpAddrControlNetIfIndex	1.3.6.1.4.1.6296.101.11.2.2.6	Integer32	read-write	Network interface index 1..4094 : VLAN 10000..11023: Tunnel interface index
IP sleIpAddrControlValue	1.3.6.1.4.1.6296.101.11.2.2.7	IpAddress	read-write	The IP address to which this entry's addressing information pertains.
I32 sleIpAddrControlMask	1.3.6.1.4.1.6296.101.11.2.2.8	Integer32	read-write	The subnet mask associated with the IP address of this entry.
INT sleIpAddrControlFlag	1.3.6.1.4.1.6296.101.11.2.2.9	INTEGER	read-write	Description.
INT sleIpAddrControlScope	1.3.6.1.4.1.6296.101.11.2.2.10	INTEGER	read-write	Description.
INT sleIpAddrControlIpIndex	1.3.6.1.4.1.6296.101.11.2.2.11	INTEGER	read-write	The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
sleIpAddrNotification	1.3.6.1.4.1.6296.101.11.2.3
NTF sleIpAddressCreated	1.3.6.1.4.1.6296.101.11.2.3.1			createIpAddress.
NTF sleIpAddressDestroyed	1.3.6.1.4.1.6296.101.11.2.3.2			destroyIpAddress.
NTF sleIpAddressIpIndexAdded	1.3.6.1.4.1.6296.101.11.2.3.3			addIpIndex
NTF sleIpAddressIpIndexDeleted	1.3.6.1.4.1.6296.101.11.2.3.4			delIpIndex
sleArp	1.3.6.1.4.1.6296.101.11.3
sleArpTable	1.3.6.1.4.1.6296.101.11.3.1		not-accessible	Description.
sleArpEntry	1.3.6.1.4.1.6296.101.11.3.1.1		not-accessible	Description.
IP sleArpIpAddress	1.3.6.1.4.1.6296.101.11.3.1.1.1	IpAddress	read-only	The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
MAC sleArpPhyAddress	1.3.6.1.4.1.6296.101.11.3.1.1.2	MacAddress	read-only	The media-dependent `physical' address.
I32 sleArpPortIndex	1.3.6.1.4.1.6296.101.11.3.1.1.3	Integer32	read-only	The interface on which this entry's equivalence is effective. 0: for any ports.
INT sleArpState	1.3.6.1.4.1.6296.101.11.3.1.1.4	INTEGER	read-only	Arp entry's currently status.
INT sleArpHwType	1.3.6.1.4.1.6296.101.11.3.1.1.5	INTEGER	read-only	Hardware Type of media.
INT sleArpHwUsed	1.3.6.1.4.1.6296.101.11.3.1.1.6	INTEGER	read-only	Arp entry's currently chip usage state.
INT sleArpUsedTime	1.3.6.1.4.1.6296.101.11.3.1.1.7	INTEGER	read-only	Arp entry's chip used time.(if sleArpState is 0, always 0 and if sleArpHwUsed is 0, always 0.)
sleArpControl	1.3.6.1.4.1.6296.101.11.3.2
INT sleArpControlRequest	1.3.6.1.4.1.6296.101.11.3.2.1	INTEGER	read-write	The request of a user command.
SLE sleArpControlStatus	1.3.6.1.4.1.6296.101.11.3.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleArpControlTimer	1.3.6.1.4.1.6296.101.11.3.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleArpControlTimeStamp	1.3.6.1.4.1.6296.101.11.3.2.4	SleControlRequestResultType	read-only	The time stamp of the last command (end of command).
TIK sleArpControlReqResult	1.3.6.1.4.1.6296.101.11.3.2.5	TimeTicks	read-only	The result of the last user command.
I32 sleArpControlNetIfIndex	1.3.6.1.4.1.6296.101.11.3.2.6	Integer32	read-write	Network interface index.
IP sleArpControlIpAddress	1.3.6.1.4.1.6296.101.11.3.2.7	IpAddress	read-write	The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
MAC sleArpControlPhyAddress	1.3.6.1.4.1.6296.101.11.3.2.8	MacAddress	read-write	The media-dependent `physical' address.
INT sleArpControlState	1.3.6.1.4.1.6296.101.11.3.2.9	INTEGER	read-write	Arp entry's currently status.
INT sleArpControlMask	1.3.6.1.4.1.6296.101.11.3.2.10	INTEGER	read-write	Description.
sleArpNotification	1.3.6.1.4.1.6296.101.11.3.3
NTF sleArpEntryCreated	1.3.6.1.4.1.6296.101.11.3.3.1			createArpEntry.
NTF sleArpEntryDestroyed	1.3.6.1.4.1.6296.101.11.3.3.2			destroyArpEntry.
NTF sleArpTableCleared	1.3.6.1.4.1.6296.101.11.3.3.3			clearArpTable. In this notification PDU, key of sleArpState is ifindex.0.0.0.0.
NTF sleArpTableClearedByAddr	1.3.6.1.4.1.6296.101.11.3.3.4			clearArpTableByAddr
sleRoute	1.3.6.1.4.1.6296.101.11.4
sleRouteTable	1.3.6.1.4.1.6296.101.11.4.1		not-accessible	Description.
sleRouteEntry	1.3.6.1.4.1.6296.101.11.4.1.1		not-accessible	Description.
IP sleRouteDstAddress	1.3.6.1.4.1.6296.101.11.4.1.1.1	IpAddress	read-only	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.
INT sleRouteDstMask	1.3.6.1.4.1.6296.101.11.4.1.1.2	INTEGER	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
IP sleRouteGateway	1.3.6.1.4.1.6296.101.11.4.1.1.3	IpAddress	read-only	The Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalid
INT sleRouteInterface	1.3.6.1.4.1.6296.101.11.4.1.1.4	INTEGER	read-only	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of sleNetIfIndex. Network interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface index
INT sleRouteType	1.3.6.1.4.1.6296.101.11.4.1.1.5	INTEGER	read-write	The type of route. Note that the values direct and indirect refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid has the effect of invalidating the corresponding entry in the sleRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant sleRouteType object.
INT sleRouteProto	1.3.6.1.4.1.6296.101.11.4.1.1.6	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
INT sleRouteMetric	1.3.6.1.4.1.6296.101.11.4.1.1.7	INTEGER	read-write	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's sleRouteProto value. If this metric is not used, its value should be set to -1.
INT sleRouteActive	1.3.6.1.4.1.6296.101.11.4.1.1.8	INTEGER	read-write	The active status for this routing entry.
IP sleRouteBindingSrcAddr	1.3.6.1.4.1.6296.101.11.4.1.1.9	IpAddress	read-only	The binding source IP Address for this route.
INT sleRouteDistance	1.3.6.1.4.1.6296.101.11.4.1.1.10	INTEGER	read-write	The Distance value for this route.
INT sleRouteSubtype	1.3.6.1.4.1.6296.101.11.4.1.1.11	INTEGER	read-only	The subtype of this route.
BIT sleRouteNexthopStatus	1.3.6.1.4.1.6296.101.11.4.1.1.12	Bits	read-only	The nexthop status of this route.
BIT sleRouteRibStatus	1.3.6.1.4.1.6296.101.11.4.1.1.13	Bits	read-only	The rib status for this route.
I32 sleRouteVRFIndex	1.3.6.1.4.1.6296.101.11.4.1.1.14	Integer32	read-only	VRF index in sleIpVRFTable.
sleRouteControl	1.3.6.1.4.1.6296.101.11.4.2
INT sleRouteControlRequest	1.3.6.1.4.1.6296.101.11.4.2.1	INTEGER	read-write	The request of a user command.
SLE sleRouteControlStatus	1.3.6.1.4.1.6296.101.11.4.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleRouteControlTimer	1.3.6.1.4.1.6296.101.11.4.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleRouteControlTimeStamp	1.3.6.1.4.1.6296.101.11.4.2.4	SleControlRequestResultType	read-only	The result of the last user command.
TIK sleRouteControlReqResult	1.3.6.1.4.1.6296.101.11.4.2.5	TimeTicks	read-only	The time stamp of the last command (end of command).
IP sleRouteControlDstAddress	1.3.6.1.4.1.6296.101.11.4.2.6	IpAddress	read-write	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.
INT sleRouteControlDstMask	1.3.6.1.4.1.6296.101.11.4.2.7	INTEGER	read-write	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
IP sleRouteControlGateway	1.3.6.1.4.1.6296.101.11.4.2.8	IpAddress	read-write	The Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalid
INT sleRouteControlInterface	1.3.6.1.4.1.6296.101.11.4.2.9	INTEGER	read-write	Network interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface index To config interface, sleRouteControlGateway have to be removed.
IP sleRouteControlBindingSrcAddr	1.3.6.1.4.1.6296.101.11.4.2.10	IpAddress	read-write	The binding source IP Address for this route.
INT sleRouteControlDistance	1.3.6.1.4.1.6296.101.11.4.2.11	INTEGER	read-write	The Distance value for this route.
I32 sleRouteControlVRFIndex	1.3.6.1.4.1.6296.101.11.4.2.12	Integer32	read-write	VRF index in sleIpVRFTable.
sleRouteNotification	1.3.6.1.4.1.6296.101.11.4.3
NTF sleRouteStaticCreated	1.3.6.1.4.1.6296.101.11.4.3.1			createStaticRoute
NTF sleRouteStaticDestroyed	1.3.6.1.4.1.6296.101.11.4.3.2			destroyStaticRoute
NTF sleRouteStaticProfileChanged	1.3.6.1.4.1.6296.101.11.4.3.3			setStaticRouteProfile
sleDhcpClient	1.3.6.1.4.1.6296.101.11.5
sleDhcpClTable	1.3.6.1.4.1.6296.101.11.5.1		not-accessible	Description.
sleDhcpClEntry	1.3.6.1.4.1.6296.101.11.5.1.1		not-accessible	Description.
INT sleDhcpClMode	1.3.6.1.4.1.6296.101.11.5.1.1.1	INTEGER	read-only	DHCP Client activity state in this interface.
IP sleDhcpClIpAddr	1.3.6.1.4.1.6296.101.11.5.1.1.2	IpAddress	read-only	The IP address acquired by DHCP Client active in this interface.
IP sleDhcpClNetmask	1.3.6.1.4.1.6296.101.11.5.1.1.3	IpAddress	read-only	The subnet mask associated with the IP address acquired by DHCP Client. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
IP sleDhcpClGateway	1.3.6.1.4.1.6296.101.11.5.1.1.4	IpAddress	read-only	The Gateway's IP address acquired by DHCP Client active in this interface.
IP sleDhcpClDnsServer	1.3.6.1.4.1.6296.101.11.5.1.1.5	IpAddress	read-only	The DNS server's IP address acquired by DHCP Client active in this interface.
IP sleDhcpClServer	1.3.6.1.4.1.6296.101.11.5.1.1.6	IpAddress	read-only	DHCP Server's IP address.
OCT sleDhcpClClientId	1.3.6.1.4.1.6296.101.11.5.1.1.7	OCTET STRING	read-only	DHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.
INT sleDhcpClClientIdStyle	1.3.6.1.4.1.6296.101.11.5.1.1.8	INTEGER	read-only	DHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal format
OCT sleDhcpClClassId	1.3.6.1.4.1.6296.101.11.5.1.1.9	OCTET STRING	read-only	DHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.
INT sleDhcpClClassIdStyle	1.3.6.1.4.1.6296.101.11.5.1.1.10	INTEGER	read-only	DHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal format
I32 sleDhcpClLeasetime	1.3.6.1.4.1.6296.101.11.5.1.1.11	Integer32	read-only	The leased time for IP address acquired by DHCP Client. Default lease-time: 3600s
INT sleDhcpClState	1.3.6.1.4.1.6296.101.11.5.1.1.12	INTEGER	read-only	The operating status of DHCP Client.
sleDhcpClControl	1.3.6.1.4.1.6296.101.11.5.2
INT sleDhcpClControlRequest	1.3.6.1.4.1.6296.101.11.5.2.1	INTEGER	read-write	The request of a user command.
SLE sleDhcpClControlStatus	1.3.6.1.4.1.6296.101.11.5.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleDhcpClControlTimer	1.3.6.1.4.1.6296.101.11.5.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleDhcpClControlTimeStamp	1.3.6.1.4.1.6296.101.11.5.2.4	SleControlRequestResultType	read-only	The time stamp of the last command (end of command).
TIK sleDhcpClControlReqResult	1.3.6.1.4.1.6296.101.11.5.2.5	TimeTicks	read-only	The result of the last user command.
I32 sleDhcpClControlNetIfIndex	1.3.6.1.4.1.6296.101.11.5.2.6	Integer32	read-write	Network Interface Index.
INT sleDhcpClControlMode	1.3.6.1.4.1.6296.101.11.5.2.7	INTEGER	read-write	DHCP Client activity state in this interface.
OCT sleDhcpClControlClientId	1.3.6.1.4.1.6296.101.11.5.2.8	OCTET STRING	read-write	DHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.
INT sleDhcpClControlClientIdStyle	1.3.6.1.4.1.6296.101.11.5.2.9	INTEGER	read-write	DHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal format
OCT sleDhcpClControlClassId	1.3.6.1.4.1.6296.101.11.5.2.10	OCTET STRING	read-write	DHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.
INT sleDhcpClControlClassIdStyle	1.3.6.1.4.1.6296.101.11.5.2.11	INTEGER	read-write	DHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal format
I32 sleDhcpClControlLeasetime	1.3.6.1.4.1.6296.101.11.5.2.12	Integer32	read-write	The leased time for IP address acquired by DHCP Client. Default lease-time: 3600s
INT sleDhcpClControlUpdateIP	1.3.6.1.4.1.6296.101.11.5.2.13	INTEGER	read-write	Update DHCP client operating status. 0 : default 1 : renew 2 : release
sleDhcpClNotification	1.3.6.1.4.1.6296.101.11.5.3
NTF sleDhcpClModeChanged	1.3.6.1.4.1.6296.101.11.5.3.1			setDhcpClMode.
NTF sleDhcpClProfileChanged	1.3.6.1.4.1.6296.101.11.5.3.2			setDhcpClProfile.
NTF sleDhcpClStateChanged	1.3.6.1.4.1.6296.101.11.5.3.3			ChangeDhcpClState.
sleV2DhcpClient	1.3.6.1.4.1.6296.101.11.6
sleNetworkBase	1.3.6.1.4.1.6296.101.11.7
sleNetworkBaseInfo	1.3.6.1.4.1.6296.101.11.7.1
INT sleNetworkArpAgingTime	1.3.6.1.4.1.6296.101.11.7.1.1	INTEGER	read-only	System Arp Aging Time
INT sleNetworkBaseVrfDynamicForwardBinding	1.3.6.1.4.1.6296.101.11.7.1.2	INTEGER	read-only	Description.
sleNetworkBaseControl	1.3.6.1.4.1.6296.101.11.7.2
INT sleNetworkControlRequest	1.3.6.1.4.1.6296.101.11.7.2.1	INTEGER	read-write	Description.
SLE sleNetworkControlStatus	1.3.6.1.4.1.6296.101.11.7.2.2	SleControlStatusType	read-only	Description.
G32 sleNetworkControlTimer	1.3.6.1.4.1.6296.101.11.7.2.3	Gauge32	read-write	Description.
TIK sleNetworkControlTimeStamp	1.3.6.1.4.1.6296.101.11.7.2.4	TimeTicks	read-only	Description.
SLE sleNetworkControlReqResult	1.3.6.1.4.1.6296.101.11.7.2.5	SleControlRequestResultType	read-only	Description.
INT sleNetworkControlArpAgingTime	1.3.6.1.4.1.6296.101.11.7.2.6	INTEGER	read-write	Description.
INT sleNetworkControlVrfDynamicForwardBinding	1.3.6.1.4.1.6296.101.11.7.2.7	INTEGER	read-write	Description.
sleNetworkBaseNotification	1.3.6.1.4.1.6296.101.11.7.3
NTF sleNetworkArpProfileChanged	1.3.6.1.4.1.6296.101.11.7.3.1			Description.
sleTunnel	1.3.6.1.4.1.6296.101.11.8
sleTunnelIfTable	1.3.6.1.4.1.6296.101.11.8.1		not-accessible	Description.
sleTunnelIfEntry	1.3.6.1.4.1.6296.101.11.8.1.1		not-accessible	Description.
I32 sleTunnelIfIndex	1.3.6.1.4.1.6296.101.11.8.1.1.1	Integer32	read-only	Tunnel interface index
IP sleTunnelIfLocalAddress	1.3.6.1.4.1.6296.101.11.8.1.1.2	IpAddress	read-only	The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.
IP sleTunnelIfRemoteAddress	1.3.6.1.4.1.6296.101.11.8.1.1.3	IpAddress	read-only	The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.
IAN sleTunnelIfMode	1.3.6.1.4.1.6296.101.11.8.1.1.4	IANAtunnelType	read-only	The encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulation
I32 sleTunnelIfTTL	1.3.6.1.4.1.6296.101.11.8.1.1.5	Integer32	read-only	The TTL to use in the outer IP header.
INT sleTunnelIfDscpMode	1.3.6.1.4.1.6296.101.11.8.1.1.6	INTEGER	read-only	The DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value.
I32 sleTunnelIfDscp	1.3.6.1.4.1.6296.101.11.8.1.1.7	Integer32	read-only	The static DiffServ field value to use in the outer IP header.
I32 sleTunnelIfKeepaliveInterval	1.3.6.1.4.1.6296.101.11.8.1.1.8	Integer32	read-only	Specifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)
I32 sleTunnelIfKeepaliveRetry	1.3.6.1.4.1.6296.101.11.8.1.1.9	Integer32	read-only	Specifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)
INT sleTunnelIfPathMtuDiscovery	1.3.6.1.4.1.6296.101.11.8.1.1.10	INTEGER	read-only	Path mtu discovery on tunnel.
OCT sleTunnelIfVRFName	1.3.6.1.4.1.6296.101.11.8.1.1.11	OCTET STRING	read-only	VPN Routing/Forwarding instance name.
OCT sleTunnelIfBindingPorts	1.3.6.1.4.1.6296.101.11.8.1.1.12	OCTET STRING	read-only	Tunnel binding ports map.
IP sleTunnelIfLocalAddress6	1.3.6.1.4.1.6296.101.11.8.1.1.13	InetAddress	read-only	The address of the local endpoint of the tunnel for IPv6
IP sleTunnelIfRemoteAddress6	1.3.6.1.4.1.6296.101.11.8.1.1.14	InetAddress	read-only	The address of the remote endpoint of the tunnel for IPv6
INT sleTunnelIfChecksum	1.3.6.1.4.1.6296.101.11.8.1.1.15	INTEGER	read-only	A checksum feature for the tunnel.
MAC sleTunnelIfDmac	1.3.6.1.4.1.6296.101.11.8.1.1.16	MacAddress	read-only	A destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)
INT sleTunnelIfTos	1.3.6.1.4.1.6296.101.11.8.1.1.17	INTEGER	read-only	A value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.
sleTunnelIfControl	1.3.6.1.4.1.6296.101.11.8.2
INT sleTunnelIfControlRequest	1.3.6.1.4.1.6296.101.11.8.2.1	INTEGER	read-write	The request of a user command.
SLE sleTunnelIfControlStatus	1.3.6.1.4.1.6296.101.11.8.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleTunnelIfControlTimer	1.3.6.1.4.1.6296.101.11.8.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleTunnelIfControlTimeStamp	1.3.6.1.4.1.6296.101.11.8.2.4	SleControlRequestResultType	read-only	The result of the last user command.
TIK sleTunnelIfControlReqResult	1.3.6.1.4.1.6296.101.11.8.2.5	TimeTicks	read-only	The time stamp of the last command (end of command).
I32 sleTunnelIfControlIndex	1.3.6.1.4.1.6296.101.11.8.2.6	Integer32	read-write	Tunnel interface index
IP sleTunnelIfControlLocalAddress	1.3.6.1.4.1.6296.101.11.8.2.7	IpAddress	read-write	The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.
IP sleTunnelIfControlRemoteAddress	1.3.6.1.4.1.6296.101.11.8.2.8	IpAddress	read-write	The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.
IAN sleTunnelIfControlMode	1.3.6.1.4.1.6296.101.11.8.2.9	IANAtunnelType	read-write	The encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulation
I32 sleTunnelIfControlTTL	1.3.6.1.4.1.6296.101.11.8.2.10	Integer32	read-write	The TTL to use in the outer IP header.
INT sleTunneIflControlDscpMode	1.3.6.1.4.1.6296.101.11.8.2.11	INTEGER	read-write	The DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value.
I32 sleTunneIflControlDscp	1.3.6.1.4.1.6296.101.11.8.2.12	Integer32	read-write	The static DiffServ field value to use in the outer IP header.
I32 sleTunnelIfControlKeepaliveInterval	1.3.6.1.4.1.6296.101.11.8.2.13	Integer32	read-write	Specifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)
I32 sleTunneIflControlKeepaliveRetry	1.3.6.1.4.1.6296.101.11.8.2.14	Integer32	read-write	Specifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)
INT sleTunnelIfControlPathMtuDiscovery	1.3.6.1.4.1.6296.101.11.8.2.15	INTEGER	read-write	Path mtu discovery on tunnel.
OCT sleTunnelIfControlVRFName	1.3.6.1.4.1.6296.101.11.8.2.16	OCTET STRING	read-write	VPN Routing/Forwarding instance name.
IP sleTunnelIfControlLocalAddress6	1.3.6.1.4.1.6296.101.11.8.2.17	InetAddress	read-write	The address of the local endpoint of the tunnel for IPv6
IP sleTunnelIfControlRemoteAddress6	1.3.6.1.4.1.6296.101.11.8.2.18	InetAddress	read-write	The address of the remote endpoint of the tunnel for IPv6
INT sleTunnelIfControlChecksum	1.3.6.1.4.1.6296.101.11.8.2.19	INTEGER	read-write	A checksum feature for the tunnel.
MAC sleTunnelIfControlDmac	1.3.6.1.4.1.6296.101.11.8.2.20	MacAddress	read-write	A destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)
INT sleTunnelIfControlTos	1.3.6.1.4.1.6296.101.11.8.2.21	INTEGER	read-write	A value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.
sleTunnelIfNotification	1.3.6.1.4.1.6296.101.11.8.3
NTF sleTunnelIfCreated	1.3.6.1.4.1.6296.101.11.8.3.1			Description.
NTF sleTunnelIfDeleted	1.3.6.1.4.1.6296.101.11.8.3.2			Description.
NTF sleTunnelIfLocalAddressChanged	1.3.6.1.4.1.6296.101.11.8.3.3			Description.
NTF sleTunnelIfRemoteAddressChanged	1.3.6.1.4.1.6296.101.11.8.3.4			Description.
NTF sleTunnelIfModeChanged	1.3.6.1.4.1.6296.101.11.8.3.5			Description.
NTF sleTunnelIfTTLChanged	1.3.6.1.4.1.6296.101.11.8.3.6			Description.
NTF sleTunnelIfDscpChanged	1.3.6.1.4.1.6296.101.11.8.3.7			Description.
NTF sleTunnelIfKeepaliveChanged	1.3.6.1.4.1.6296.101.11.8.3.8			Description.
NTF sleTunnelIfPathMtuDiscoveryChanged	1.3.6.1.4.1.6296.101.11.8.3.9			Description.
NTF sleTunnelIfVRFNameSet	1.3.6.1.4.1.6296.101.11.8.3.10			Description.
NTF sleTunnelIfVRFNameUnset	1.3.6.1.4.1.6296.101.11.8.3.11			Description.
NTF sleTunnelIfLocalAddress6Changed	1.3.6.1.4.1.6296.101.11.8.3.12			setTunnelLocalAddr6
NTF sleTunnelIfRemoteAddress6Changed	1.3.6.1.4.1.6296.101.11.8.3.13			setTunnelRemoteAddr6
sleTunnelAddressTable	1.3.6.1.4.1.6296.101.11.8.4		not-accessible	Description.
sleTunnelAddressEntry	1.3.6.1.4.1.6296.101.11.8.4.1		not-accessible	Description.
IP sleTunnelAddressValue	1.3.6.1.4.1.6296.101.11.8.4.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
I32 sleTunnelAddressMask	1.3.6.1.4.1.6296.101.11.8.4.1.2	Integer32	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
IP sleTunnelIpAddrBcast	1.3.6.1.4.1.6296.101.11.8.4.1.3	IpAddress	read-only	Description.
BIT sleTunnelAddressFlag	1.3.6.1.4.1.6296.101.11.8.4.1.4	Bits	read-only	dynamic: ~ permanent primary : ~ secondary anycast: this bit is available for ipv6 only. The others are available for ipv4 only.
I32 sleTunnelAddressScope	1.3.6.1.4.1.6296.101.11.8.4.1.5	Integer32	read-only	default : global In linux, 200 - site 0 - global 1..252 - scopeNUM 253 - link 254 - host 255 - nowhere
INT sleTunnelAddressUnnumIfIndex	1.3.6.1.4.1.6296.101.11.8.4.1.6	INTEGER	read-only	The unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)
INT sleTunnelAddressUnnumIpIndex	1.3.6.1.4.1.6296.101.11.8.4.1.7	INTEGER	read-only	The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
sleTunnelAddressControl	1.3.6.1.4.1.6296.101.11.8.5
INT sleTunnelAddressControlRequest	1.3.6.1.4.1.6296.101.11.8.5.1	INTEGER	read-write	The request of a user command.
SLE sleTunnelAddressControlStatus	1.3.6.1.4.1.6296.101.11.8.5.2	SleControlStatusType	read-only	The status of a user command.
G32 sleTunnelAddressControlTimer	1.3.6.1.4.1.6296.101.11.8.5.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleTunnelAddressControlTimeStamp	1.3.6.1.4.1.6296.101.11.8.5.4	SleControlRequestResultType	read-only	The result of the last user command.
TIK sleTunnelAddressControlReqResult	1.3.6.1.4.1.6296.101.11.8.5.5	TimeTicks	read-only	The time stamp of the last command (end of command).
I32 sleTunnelAddressControlTunnelIfIndex	1.3.6.1.4.1.6296.101.11.8.5.6	Integer32	read-write	Tunnel interface index
IP sleTunnelAddressControlValue	1.3.6.1.4.1.6296.101.11.8.5.7	IpAddress	read-write	The IP address to which this entry's addressing information pertains.
I32 sleTunnelAddressControlMask	1.3.6.1.4.1.6296.101.11.8.5.8	Integer32	read-write	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
INT sleTunnelAddressControlFlag	1.3.6.1.4.1.6296.101.11.8.5.9	INTEGER	read-write	default : primary
INT sleTunnelAddressControlScope	1.3.6.1.4.1.6296.101.11.8.5.10	INTEGER	read-write	default : global not applicable : nowhere
INT sleTunnelAddressControlUnnumIfIndex	1.3.6.1.4.1.6296.101.11.8.5.11	INTEGER	read-write	The unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)
INT sleTunnelAddressControlUnnumIpIndex	1.3.6.1.4.1.6296.101.11.8.5.12	INTEGER	read-write	The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
sleTunnelAddressNotification	1.3.6.1.4.1.6296.101.11.8.6
NTF sleTunnelAddressCreated	1.3.6.1.4.1.6296.101.11.8.6.1			Description.
NTF sleTunnelAddressDeleted	1.3.6.1.4.1.6296.101.11.8.6.2			Description.
NTF sleTunnelAddressUnnumChanged	1.3.6.1.4.1.6296.101.11.8.6.3			setIfUnnumbered
NTF sleTunnelAddressUnnumDeleted	1.3.6.1.4.1.6296.101.11.8.6.4			delIfUnnumbered
sleIpVRF	1.3.6.1.4.1.6296.101.11.9
sleIpVRFTable	1.3.6.1.4.1.6296.101.11.9.1		not-accessible	Description.
sleIpVRFEntry	1.3.6.1.4.1.6296.101.11.9.1.1		not-accessible	Description.
I32 sleIpVRFIndex	1.3.6.1.4.1.6296.101.11.9.1.1.1	Integer32	read-only	VRF index.
OCT sleIpVRFName	1.3.6.1.4.1.6296.101.11.9.1.1.2	OCTET STRING	read-only	VRF name.
OCT sleIpVRFDesignatedPorts	1.3.6.1.4.1.6296.101.11.9.1.1.3	OCTET STRING	read-only	The port map of VRF designated-port.
IP sleIpVRFRouterId	1.3.6.1.4.1.6296.101.11.9.1.1.4	IpAddress	read-only	Router-Identifier
OCT sleIpVRFDescription	1.3.6.1.4.1.6296.101.11.9.1.1.5	OCTET STRING	read-only	The description of VRF.
sleIpVRFControl	1.3.6.1.4.1.6296.101.11.9.2
INT sleIpVRFControlRequest	1.3.6.1.4.1.6296.101.11.9.2.1	INTEGER	read-write	The request of a user command.
SLE sleIpVRFControlStatus	1.3.6.1.4.1.6296.101.11.9.2.2	SleControlStatusType	read-only	The status of a user command.
G32 sleIpVRFControlTimer	1.3.6.1.4.1.6296.101.11.9.2.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleIpVRFControlTimeStamp	1.3.6.1.4.1.6296.101.11.9.2.4	SleControlRequestResultType	read-only	The result of the last user command.
TIK sleIpVRFControlReqResult	1.3.6.1.4.1.6296.101.11.9.2.5	TimeTicks	read-only	The time stamp of the last command (end of command).
OCT sleIpVRFControlName	1.3.6.1.4.1.6296.101.11.9.2.6	OCTET STRING	read-write	VRF name
OCT sleIpVRFControlDesignatedPorts	1.3.6.1.4.1.6296.101.11.9.2.7	OCTET STRING	read-write	The port map of VRF designated-port.
IP sleIpVRFControlRouterId	1.3.6.1.4.1.6296.101.11.9.2.8	IpAddress	read-write	Router-Identifier
OCT sleIpVRFControlDescription	1.3.6.1.4.1.6296.101.11.9.2.9	OCTET STRING	read-write	The description of VRF.
sleIpVRFNotification	1.3.6.1.4.1.6296.101.11.9.3
NTF sleIpVRFCreated	1.3.6.1.4.1.6296.101.11.9.3.1			Description.
NTF sleIpVRFDeleted	1.3.6.1.4.1.6296.101.11.9.3.2			Description.
NTF sleIpVRFDesignatedPortsSet	1.3.6.1.4.1.6296.101.11.9.3.3			Description.
NTF sleIpVRFDesignatedPortsUnset	1.3.6.1.4.1.6296.101.11.9.3.4			Description.
NTF sleIpVRFRouterIdChanged	1.3.6.1.4.1.6296.101.11.9.3.5			Description.
NTF sleIpVRFDescriptionChanged	1.3.6.1.4.1.6296.101.11.9.3.6			Description.
sleIpVRFSelectionSourceTable	1.3.6.1.4.1.6296.101.11.9.4		not-accessible	Description.
sleIpVRFSelectionSourceEntry	1.3.6.1.4.1.6296.101.11.9.4.1		not-accessible	Description.
INT sleIpVRFSelectionSrcIndex	1.3.6.1.4.1.6296.101.11.9.4.1.1	INTEGER	read-only	VRF selection source index.
IP sleIpVRFSelectionSrcAddr	1.3.6.1.4.1.6296.101.11.9.4.1.2	IpAddress	read-only	VRF selection by source IP address.
I32 sleIpVRFSelectionSrcMask	1.3.6.1.4.1.6296.101.11.9.4.1.3	Integer32	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
OCT sleIpVRFSelectionSrcVRFName	1.3.6.1.4.1.6296.101.11.9.4.1.4	OCTET STRING	read-only	VPN Routing/Forwarding instance name.
sleIpVRFSelectionSourceControl	1.3.6.1.4.1.6296.101.11.9.5
INT sleIpVRFSelectionSrcControlRequest	1.3.6.1.4.1.6296.101.11.9.5.1	INTEGER	read-write	The request of a user command.
SLE sleIpVRFSelectionSrcControlStatus	1.3.6.1.4.1.6296.101.11.9.5.2	SleControlStatusType	read-only	The status of a user command.
G32 sleIpVRFSelectionSrcControlTimer	1.3.6.1.4.1.6296.101.11.9.5.3	Gauge32	read-write	The maximum wait time for the manager for a long running user command.
SLE sleIpVRFSelectionSrcControlTimeStamp	1.3.6.1.4.1.6296.101.11.9.5.4	SleControlRequestResultType	read-only	The result of the last user command.
TIK sleIpVRFSelectionSrcControlReqResult	1.3.6.1.4.1.6296.101.11.9.5.5	TimeTicks	read-only	The time stamp of the last command (end of command).
IP sleIpVRFSelectionSrcControlAddr	1.3.6.1.4.1.6296.101.11.9.5.6	IpAddress	read-write	VRF selection by source IP address.
I32 sleIpVRFSelectionSrcControlMask	1.3.6.1.4.1.6296.101.11.9.5.7	Integer32	read-write	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
OCT sleIpVRFSelectionSrcControlVRFName	1.3.6.1.4.1.6296.101.11.9.5.8	OCTET STRING	read-write	VPN Routing/Forwarding instance name.
sleIpVRFSelectionSourceNotification	1.3.6.1.4.1.6296.101.11.9.6
NTF sleIpVRFSelectionSrcSet	1.3.6.1.4.1.6296.101.11.9.6.1			Description.
NTF sleIpVRFSelectionSrcUnset	1.3.6.1.4.1.6296.101.11.9.6.2			Description.
sleBFD	1.3.6.1.4.1.6296.101.11.10
sleBFDBase	1.3.6.1.4.1.6296.101.11.10.1
sleBFDBaseInfo	1.3.6.1.4.1.6296.101.11.10.1.1
INT sleBFDEnable	1.3.6.1.4.1.6296.101.11.10.1.1.1	INTEGER	read-only	BFD fast-detect is enabled or disabled.
INT sleBFDEchoEnable	1.3.6.1.4.1.6296.101.11.10.1.1.2	INTEGER	read-only	BFD Echo function is enabled or disabled.
INT sleBFDSlowTimer	1.3.6.1.4.1.6296.101.11.10.1.1.3	INTEGER	read-only	BFD Slow Timer in unit of milliseconds default: 1000(ms)
sleBFDBaseControl	1.3.6.1.4.1.6296.101.11.10.1.2
INT sleBFDControlRequest	1.3.6.1.4.1.6296.101.11.10.1.2.1	INTEGER	read-write	The request of a user command
SLE sleBFDControlStatus	1.3.6.1.4.1.6296.101.11.10.1.2.2	SleControlStatusType	read-only	The status of user command.
G32 sleBFDControlTimer	1.3.6.1.4.1.6296.101.11.10.1.2.3	Gauge32	read-write	The maximum time for the manager for a long running user command.
TIK sleBFDControlTimeStamp	1.3.6.1.4.1.6296.101.11.10.1.2.4	TimeTicks	read-only	The time stamp of the last command(end of command).
SLE sleBFDControlReqResult	1.3.6.1.4.1.6296.101.11.10.1.2.5	SleControlRequestResultType	read-only	The result of the last user command.
INT sleBFDControlEnable	1.3.6.1.4.1.6296.101.11.10.1.2.6	INTEGER	read-write	BFD fast-detect is enabled or disabled.
INT sleBFDControlEchoEnable	1.3.6.1.4.1.6296.101.11.10.1.2.7	INTEGER	read-write	BFD Echo function is enabled or disabled.
INT sleBFDControlSlowTimer	1.3.6.1.4.1.6296.101.11.10.1.2.8	INTEGER	read-write	BFD Slow Timer in unit of milliseconds default: 1000(ms)
sleBFDBaseNotification	1.3.6.1.4.1.6296.101.11.10.1.3
NTF sleBFDBaseProfileChanged	1.3.6.1.4.1.6296.101.11.10.1.3.1			Description.
sleBFDInterface	1.3.6.1.4.1.6296.101.11.10.2
sleBFDInterfaceTable	1.3.6.1.4.1.6296.101.11.10.2.1		not-accessible	Description.
sleBFDInterfaceEntry	1.3.6.1.4.1.6296.101.11.10.2.1.1		not-accessible	Description.
INT sleBFDIfRxInterval	1.3.6.1.4.1.6296.101.11.10.2.1.1.1	INTEGER	read-only	Required Min Rx Interval of BFD control packet in this interface. default: 50(ms)
INT sleBFDIfTxInterval	1.3.6.1.4.1.6296.101.11.10.2.1.1.2	INTEGER	read-only	Required Min Tx Interval of BFD control packet in this interface. default: 50(ms)
INT sleBFDIfDetectMulti	1.3.6.1.4.1.6296.101.11.10.2.1.1.3	INTEGER	read-only	Detect Multi value of BFD control packet in this interface. default: 3
I32 sleBFDIfRxIntervalIPv6	1.3.6.1.4.1.6296.101.11.10.2.1.1.4	Integer32	read-only	Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
I32 sleBFDIfTxIntervalIJPv6	1.3.6.1.4.1.6296.101.11.10.2.1.1.5	Integer32	read-only	Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
I32 sleBFDIfDetectMultiIPv6	1.3.6.1.4.1.6296.101.11.10.2.1.1.6	Integer32	read-only	Detect Multi value of IPv6 BFD control packet in this interface. default: 3
sleBFDInterfaceControl	1.3.6.1.4.1.6296.101.11.10.2.2
INT sleBFDIfControlRequest	1.3.6.1.4.1.6296.101.11.10.2.2.1	INTEGER	read-write	The request of a user command
SLE sleBFDIfControlStatus	1.3.6.1.4.1.6296.101.11.10.2.2.2	SleControlStatusType	read-only	The status of user command.
G32 sleBFDIfControlTimer	1.3.6.1.4.1.6296.101.11.10.2.2.3	Gauge32	read-write	The maximum time for the manager for a long running user command.
TIK sleBFDIfControlTimeStamp	1.3.6.1.4.1.6296.101.11.10.2.2.4	TimeTicks	read-only	The time stamp of the last command(end of command).
SLE sleBFDIfControlReqResult	1.3.6.1.4.1.6296.101.11.10.2.2.5	SleControlRequestResultType	read-only	The result of the last user command.
I32 sleBFDIfControlNetIfIndex	1.3.6.1.4.1.6296.101.11.10.2.2.6	Integer32	read-write	BFD Interface Index.
INT sleBFDIfControlRxInterval	1.3.6.1.4.1.6296.101.11.10.2.2.7	INTEGER	read-write	Required Min Rx Interval of BFD control packet in this interface. default: 50(ms)
INT sleBFDIfControlTxInterval	1.3.6.1.4.1.6296.101.11.10.2.2.8	INTEGER	read-write	Required Min Tx Interval of BFD control packet in this interface. default: 50(ms)
INT sleBFDIfControlDetectMulti	1.3.6.1.4.1.6296.101.11.10.2.2.9	INTEGER	read-write	Detect Multi value of BFD control packet in this interface. default: 3
I32 sleBFDIfControlRxIntervalIPv6	1.3.6.1.4.1.6296.101.11.10.2.2.10	Integer32	read-write	Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
I32 sleBFDIfControlTxIntervalIPv6	1.3.6.1.4.1.6296.101.11.10.2.2.11	Integer32	read-write	Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
I32 sleBFDIfControlDetectMultiIPv6	1.3.6.1.4.1.6296.101.11.10.2.2.12	Integer32	read-write	Detect Multi value of IPv6 BFD control packet in this interface. default: 3
sleBFDInterfaceNotification	1.3.6.1.4.1.6296.101.11.10.2.3
NTF sleBFDIfProfileChanged	1.3.6.1.4.1.6296.101.11.10.2.3.1			Description.
sleBFDSession	1.3.6.1.4.1.6296.101.11.10.3
sleBFDSessionInfo	1.3.6.1.4.1.6296.101.11.10.3.1
sleBFDSessionInfoTable	1.3.6.1.4.1.6296.101.11.10.3.1.1		not-accessible	Description.
sleBFDSessionInfoEntry	1.3.6.1.4.1.6296.101.11.10.3.1.1.1		not-accessible	Description.
IPt sleBFDSessionNeighAddrType	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.1	InetAddressType	read-only	Type of Neighbor Address referred to this session
IP sleBFDSessionNeighAddrValue	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.2	InetAddress	read-only	Value of Neighbor Address referred to this session.
BIT sleBFDSessionRegProtocols	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.3	Bits	read-only	Value of Neighbor Address referred to this session.
U32 sleBFDSessionLocalDiscr	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.4	Unsigned32	read-only	Discriminator of this session.
U32 sleBFDSessionRemoteDiscr	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.5	Unsigned32	read-only	Discriminator of remote session neighboring this session.
INT sleBFDSessionDetecMultiplier	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.6	INTEGER	read-only	Detect Multiplier value which this session used. default: 3
INT sleBFDSessionStatus	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.7	INTEGER	read-only	Status of this session. AdminDown(0) is same as disabled(4).
INT sleBFDSessionEchoUsage	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.8	INTEGER	read-only	Determine whether this session use or not echo function.
TIK sleBFDSessionUptime	1.3.6.1.4.1.6296.101.11.10.3.1.1.1.9	TimeTicks	read-only	The time since this sessions status changed into Up.
sleBFDSessionStats	1.3.6.1.4.1.6296.101.11.10.3.2
sleBFDSessionStatsTable	1.3.6.1.4.1.6296.101.11.10.3.2.1		not-accessible	Description.
sleBFDSessionStatsEntry	1.3.6.1.4.1.6296.101.11.10.3.2.1.1		not-accessible	Description.
U32 sleBFDSessionStatsHolddownTime	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.1	Unsigned32	read-only	Type of Neighbor Address referred to this session.
U32 sleBFDSessionStatsHolddownExpires	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.2	Unsigned32	read-only	The time remaining before this entry change into down status without receiving hello in unit of milliseconds.
U32 sleBFDSessionStatsHolddownHitCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.3	Unsigned32	read-only	Hit Count whose this session status chang into down.
U32 sleBFDSessionStatsHelloTime	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.4	Unsigned32	read-only	The time is when it expects next hello, after receiving that in unit of milliseconds.
U32 sleBFDSessionStatsHelloHitCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.5	Unsigned32	read-only	Hit Count whose this session received.
U32 sleBFDSessionStatsRxCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.6	Unsigned32	read-only	Hit Count whose this session received control packet.
U32 sleBFDSessionStatsRxAvgInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.7	Unsigned32	read-only	Average interval whose this session received control packet.
U32 sleBFDSessionStatsRxMinInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.8	Unsigned32	read-only	Minimum interval whose this session received control packet.
U32 sleBFDSessionStatsRxMaxInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.9	Unsigned32	read-only	Maximum interval whose this session received control packet.
U32 sleBFDSessionStatsTxCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.10	Unsigned32	read-only	Hit Count whose this session send control packet.
U32 sleBFDSessionStatsTxAvgInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.11	Unsigned32	read-only	Average interval whose this session sent control packet.
U32 sleBFDSessionStatsTxMinInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.12	Unsigned32	read-only	Minimum interval whose this session sent control packet.
U32 sleBFDSessionStatsTxMaxInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.13	Unsigned32	read-only	Maximum interval whose this session received control packet.
U32 sleBFDSessionStatsEchoRxCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.14	Unsigned32	read-only	Hit Count whose this session received echo packet
U32 sleBFDSessionStatsEchoRxAvgInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.15	Unsigned32	read-only	Average interval whose this session received echo packet
U32 sleBFDSessionStatsEchoRxMinInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.16	Unsigned32	read-only	Minimum interval whose this session received echo packet
U32 sleBFDSessionStatsEchoRxMaxInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.17	Unsigned32	read-only	Maximum interval whose this session received echo packet
U32 sleBFDSessionStatsEchoTxCount	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.18	Unsigned32	read-only	Hit Count whose this session send echo packet
U32 sleBFDSessionStatsEchoTxAvgInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.19	Unsigned32	read-only	Average interval whose this session sent echo packet.
U32 sleBFDSessionStatsEchoTxMinInterva	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.20	Unsigned32	read-only	Minimum interval whose this session sent echo packet.
U32 sleBFDSessionStatsEchoTxMaxInterval	1.3.6.1.4.1.6296.101.11.10.3.2.1.1.21	Unsigned32	read-only	Maximum interval whose this session received echo packet.
sleBFDSessionLocal	1.3.6.1.4.1.6296.101.11.10.3.3
sleBFDSessionLocalTable	1.3.6.1.4.1.6296.101.11.10.3.3.1		not-accessible	Description.
sleBFDSessionLocalEntry	1.3.6.1.4.1.6296.101.11.10.3.3.1.1		not-accessible	Description.
INT sleBFDSessionLocalDiag	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.1	INTEGER	read-only	Value of State field of this sessions control packet.
INT sleBFDSessionLocalState	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.2	INTEGER	read-only	Value of Diag field of this sessions control packet
BIT sleBFDSessionLocalFlags	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.3	Bits	read-only	Value of Flags field of this sessions control packet.
INT sleBFDSessionLocalMultiplier	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.4	INTEGER	read-only	Value of MinTxInterval field of this sessions control packet in unit of microseconds.
U32 sleBFDSessionLocalMinTxInterval	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.5	Unsigned32	read-only	Value of MinTxInterval field of this sessions control packet in unit of microseconds.
U32 sleBFDSessionLocalMinRxInterval	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.6	Unsigned32	read-only	Value of MinRxInterval field of this sessions control packet in unit of microseconds.
U32 sleBFDSessionLocalMinEchoInterval	1.3.6.1.4.1.6296.101.11.10.3.3.1.1.7	Unsigned32	read-only	Value of MinEchoInterval field of this sessions control packet in unit of microseconds.
sleBFDSessionRemote	1.3.6.1.4.1.6296.101.11.10.3.4
sleBFDSessionRemoteTable	1.3.6.1.4.1.6296.101.11.10.3.4.1		not-accessible	Description.
sleBFDSessionRemoteEntry	1.3.6.1.4.1.6296.101.11.10.3.4.1.1		not-accessible	Description.
INT sleBFDSessionRemoteDiag	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.1	INTEGER	read-only	Value of State field of remote sessions control packet.
INT sleBFDSessionRemoteState	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.2	INTEGER	read-only	Value of Diag field of remote sessions control packet
BIT sleBFDSessionremoteFlags	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.3	Bits	read-only	Value of Flags field of remote sessions control packet.
INT sleBFDSessionRemoteMultiplier	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.4	INTEGER	read-only	Value of MinTxInterval field of this sessions control packet in unit of microseconds.
U32 sleBFDSessionRemoteMinTxInterval	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.5	Unsigned32	read-only	Value of MinTxInterval field of remote sessions control packet in unit of microseconds.
U32 sleBFDSessionRemoteMinRxInterval	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.6	Unsigned32	read-only	Value of MinRxInterval field of remote sessions control packet in unit of microseconds.
U32 sleBFDSessionRemoteMinEchoInterval	1.3.6.1.4.1.6296.101.11.10.3.4.1.1.7	Unsigned32	read-only	Value of MinEchoInterval field of remote sessions control packet in unit of microseconds.
sleBFDStaticGw	1.3.6.1.4.1.6296.101.11.10.4
sleBFDStaticGwTable	1.3.6.1.4.1.6296.101.11.10.4.1		not-accessible	Description.
sleBFDStaticGwEntry	1.3.6.1.4.1.6296.101.11.10.4.1.1		not-accessible	Description.
IPt sleBFDStaticGwAddrType	1.3.6.1.4.1.6296.101.11.10.4.1.1.1	InetAddressType	read-write	The BFD static Gateway address type. Only ipv4(1).
IP sleBFDStaticGwAddr	1.3.6.1.4.1.6296.101.11.10.4.1.1.2	InetAddress	read-write	The BFD static Gateway address. 4bytes
sleBFDStaticGwControl	1.3.6.1.4.1.6296.101.11.10.4.2
INT sleBFDStaticGwControlRequest	1.3.6.1.4.1.6296.101.11.10.4.2.1	INTEGER	read-write	Description.
SLE sleBFDStaticGwControlStatus	1.3.6.1.4.1.6296.101.11.10.4.2.2	SleControlStatusType	read-only	Description.
G32 sleBFDStaticGwControlTimer	1.3.6.1.4.1.6296.101.11.10.4.2.3	Gauge32	read-write	Description.
TIK sleBFDStaticGwControlTimeStamp	1.3.6.1.4.1.6296.101.11.10.4.2.4	TimeTicks	read-only	Description.
SLE sleBFDStaticGwControlReqResult	1.3.6.1.4.1.6296.101.11.10.4.2.5	SleControlRequestResultType	read-only	Description.
I32 sleBFDStaticGwControlNetIfIndex	1.3.6.1.4.1.6296.101.11.10.4.2.6	Integer32	read-write	Description.
IPt sleBFDStaticGwControlGwAddrType	1.3.6.1.4.1.6296.101.11.10.4.2.7	InetAddressType	read-write	Description.
IP sleBFDStaticGwControlGwAddr	1.3.6.1.4.1.6296.101.11.10.4.2.8	InetAddress	read-write	Description.
sleBFDStaticGwNotification	1.3.6.1.4.1.6296.101.11.10.4.3
NTF sleBFDStaticGwAdded	1.3.6.1.4.1.6296.101.11.10.4.3.1			Description.
NTF sleBFDStaticGwDeleted	1.3.6.1.4.1.6296.101.11.10.4.3.2			Description.
sleNetworkGroup	1.3.6.1.4.1.6296.101.11.14			Description.
sleNetworkNotificationGroup	1.3.6.1.4.1.6296.101.11.15			Description.

RFC description

SLE network MIB for DHCP and supported DHCP features on HANASOFT network devices.

Start monitoring Hanasoft SLE-series GPON/EPON Optical Line Terminal (IP interface/static route/DHCP configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SLE-NETWORK-MIB

What Is SLE-NETWORK-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description