SLE-MPLS-TP-TUNNEL-STATISTICS-MIB

All MIBs › SLE-MPLS-TP-TUNNEL-STATISTICS-MIB

Organization: Multiprotocol Label Switching (MPLS) Working Group

Last Updated: 2016--0-1-

Category: DASAN Networks SLE OLT Management, MPLS Transport Profile

Description: Tracks DASAN Networks SLE OLT MPLS-TP tunnel performance counters and traffic statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SLE-MPLS-TP-TUNNEL-STATISTICS-MIB?

SLE-MPLS-TP-TUNNEL-STATISTICS-MIB is a DASAN Networks (DZS) enterprise MIB for SLE-series OLTs that reports performance statistics for MPLS-TP LSPs/tunnels carried over the transport network. Per its module description, it covers MPLS-TP LSP statistics, including packet/byte counters, discards, and similar traffic-volume and performance data for each tunnel. It supports monitoring of software-level traffic performance, such as throughput and loss on a given tunnel, rather than physical hardware sensors, letting an operator spot a tunnel that is dropping packets or running outside its provisioned bandwidth. It depends on the underlying MPLS-TP tunnel/LSP identity objects defined elsewhere in the SLE MPLS-TP MIB suite to identify which tunnel each statistics row belongs to. It is deployed on DASAN/DZS SLE OLT platforms where operators need per-tunnel traffic accounting for SLA verification and capacity planning in MPLS-TP access networks. Network engineers evaluating or troubleshooting this functionality can download the SLE-MPLS-TP-TUNNEL-STATISTICS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SLE-MPLS-TP-TUNNEL-STATISTICS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DASAN Networks / DZS SLE-series OLT

Monitoring Examples

No specific object/table names were supplied for this module, so a concrete polling example can't be grounded in real identifiers; typically an operator would trend each tunnel's transmitted/received packet and discard counters over time to detect a tunnel silently dropping traffic or approaching its committed bandwidth.

What Can Be Monitored

per-tunnel packet/byte counters
tunnel discard/error counts
tunnel throughput trends
LSP performance statistics

Imported Objects

From DASAN-SMI

sleMgmt

OBJECT-IDENTITY

From MPLS-TC-STD-MIB

mplsStdMIB

OBJECT-IDENTITY

From SLE-TC-MIB

SleControlRequestResultType
SleControlStatusType

From SNMPv2-SMI

Counter64
Gauge32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32
zeroDotZero

OIDs

OID symbolic	OID numeric	Type	Access	Description
sleMpls	1.3.6.1.4.1.6296.101.16
sleMplsTpTunnelStats	1.3.6.1.4.1.6296.101.16.20			This mib contains the managed objects for MPLS-TP lsp statistics.
sleMplsTpTunnelStatsTable	1.3.6.1.4.1.6296.101.16.20.1
sleMplsTpTunnelStatsInfoTable	1.3.6.1.4.1.6296.101.16.20.1.1		not-accessible	This table contains the information about the statistics of LSP which exist on the LSR or LER.
sleMplsTpTunnelStatsInfoEntry	1.3.6.1.4.1.6296.101.16.20.1.1.1		not-accessible	An entry in this table represents the statistics of LSP. The LSP can be creates by network administator or SNMP agent as instruct by the MPLS-TP
U32 sleMplsTpTunnelStatsInfoIndex	1.3.6.1.4.1.6296.101.16.20.1.1.1.1	Unsigned32	not-accessible	Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexN. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the value signaled in the Tunnel Id of the Session object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the value signaled in the LSP ID.
OCT sleMplsTpTunnelStatsInfoTunnelName	1.3.6.1.4.1.6296.101.16.20.1.1.1.2	OCTET STRING	read-only	The tunnel name of the LSP.
INT sleMplsTpTunnelStatsInfoRole	1.3.6.1.4.1.6296.101.16.20.1.1.1.3	INTEGER	read-only	This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value MUST be set to transit(2) at transit points along the tunnel, if transit points are supported. This value MUST be set to tail(3) at the terminating point of the tunnel if tunnel tails are supported. The value headTail(4) is provided for tunnels that begin and end on the same LSR.
C64 sleMplsTpTunnelStatsInfoFwdTxPkts	1.3.6.1.4.1.6296.101.16.20.1.1.1.4	Counter64	read-only	The number of packet sent through the LSP.
C64 sleMplsTpTunnelStatsInfoFwdTxBytes	1.3.6.1.4.1.6296.101.16.20.1.1.1.5	Counter64	read-only	The total bytes sent through the LSP.
C64 sleMplsTpTunnelStatsInfoFwdRxPkts	1.3.6.1.4.1.6296.101.16.20.1.1.1.6	Counter64	read-only	The number of packet recieved through the LSP.
C64 sleMplsTpTunnelStatsInfoFwdRxBytes	1.3.6.1.4.1.6296.101.16.20.1.1.1.7	Counter64	read-only	The total bytes recieved through the LSP.
C64 sleMplsTpTunnelStatsInfoRevTxPkts	1.3.6.1.4.1.6296.101.16.20.1.1.1.8	Counter64	read-only	The number of packet sent through the LSP.
C64 sleMplsTpTunnelStatsInfoRevTxBytes	1.3.6.1.4.1.6296.101.16.20.1.1.1.9	Counter64	read-only	The total bytes sent through the LSP.
C64 sleMplsTpTunnelStatsInfoRevRxPkts	1.3.6.1.4.1.6296.101.16.20.1.1.1.10	Counter64	read-only	The number of packet recieved through the LSP.
C64 sleMplsTpTunnelStatsInfoRevRxBytes	1.3.6.1.4.1.6296.101.16.20.1.1.1.11	Counter64	read-only	The total bytes recieved through the LSP.
sleMplsTpTunnelStatsControl	1.3.6.1.4.1.6296.101.16.20.1.2
INT sleMplsTpTunnelStatsControlRequest	1.3.6.1.4.1.6296.101.16.20.1.2.1	INTEGER	read-write	This object holds the possible read-write columns that can be modified in the Vrf table. For each read-write column of Vrf table, a Set Operation control value is added in this object.
SLE sleMplsTpTunnelStatsControlStatus	1.3.6.1.4.1.6296.101.16.20.1.2.2	SleControlStatusType	read-only	This object displays the status of the configuration done.
G32 sleMplsTpTunnelStatsControlTimer	1.3.6.1.4.1.6296.101.16.20.1.2.3	Gauge32	read-write	This object is based on the SLE style where a timer is configured for every control table.
TIK sleMplsTpTunnelStatsControlTimeStamp	1.3.6.1.4.1.6296.101.16.20.1.2.4	TimeTicks	read-only	This object specifies the time at which the configuration is done.
SLE sleMplsTpTunnelStatsReqResult	1.3.6.1.4.1.6296.101.16.20.1.2.5	SleControlRequestResultType	read-only	The standard result of the SET operation is stored here.
OCT sleMplsTpTunnelStatsControlName	1.3.6.1.4.1.6296.101.16.20.1.2.6	OCTET STRING	read-write	The tunnel name of the LSP. To clear all the tunnel statistics, give the name as 'all'. To clear the specific tunnel, give the specific tunnel name.

RFC description

Monitors MPLS Transport Profile (MPLS-TP) tunnel performance statistics including packet counts and delay metrics on SLE platforms; vendor-private.

Start monitoring DASAN Networks / DZS SLE-series OLT (MPLS-TP LSP/tunnel traffic statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SLE-MPLS-TP-TUNNEL-STATISTICS-MIB

What Is SLE-MPLS-TP-TUNNEL-STATISTICS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description