SK-GE-MIB

All MIBs › SK-GE-MIB

Category: Ethernet and LAN Management, SysKonnect Network Adapters

Description: Manages SysKonnect Gigabit Ethernet adapter configuration, link status, and performance counters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SK-GE-MIB?

SK-GE-MIB is a vendor-specific MIB from SysKonnect for managing their Gigabit Ethernet network interface adapters, sitting in the networking/NIC hardware category. It exposes configuration data such as device type, driver description and version, port numbering, and per-adapter management actions. Because it surfaces driver version and adapter identification data, it supports monitoring the software/firmware state of the NIC alongside basic link/port status, letting admins confirm the adapter is running the expected driver and is properly enumerated by the host. It has no explicit dependency on other MIBs beyond standard SNMPv2 SMI conventions, though it complements IF-MIB for interface-level statistics. It is typically deployed on servers or workstations fitted with SysKonnect (later Marvell/SysKonnect) Gigabit Ethernet cards where IT staff want driver/version visibility beyond what standard interface MIBs provide, and an SK-GE-MIB download is available for IT staff who need to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SK-GE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SysKonnect Gigabit Ethernet network adapters
servers/workstations with SysKonnect NICs

Monitoring Examples

An admin would poll skGeTable/skGeEntry indexed by skGeIndex to correlate each adapter's skGeIfIndex with skGePortNumber and skGeDeviceType, confirming which physical port maps to which logical interface. Checking skGeDriverVersion and skGeDriverDescr across a fleet of servers can reveal machines running an outdated or mismatched NIC driver. skGeMibVersion identifies the MIB revision supported by the agent, while skGeAction/skGeNumber support triggering or tracking administrative actions against the adapter.

What Can Be Monitored

adapter device type
driver description
driver version
port number
interface index mapping
MIB/agent version

Imported Objects

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
NetworkAddress
OBJECT-TYPE
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
sk	1.3.6.1.4.1.179
NTF skGeSensorWarningLower	1.3.6.1.4.1.179.0.500			This trap is generated when one of the adapter sensor values exceeds the lower warning threshold.
NTF skGeSensorWarningUpper	1.3.6.1.4.1.179.0.501			This trap is generated when one of the adapter sensor values exceeds the upper warning threshold.
NTF skGeSensorErrorLower	1.3.6.1.4.1.179.0.502			This trap is generated when one of the adapter sensor values exceeds the lower error threshold.
NTF skGeSensorErrorUpper	1.3.6.1.4.1.179.0.503			This trap is generated when one of the adapter sensor values exceeds the upper error threshold.
NTF skGeRlmtChangeThresholdCondition	1.3.6.1.4.1.179.0.520			This trap is generated when the port switches exceeded the threshold.
NTF skGeRlmtChangeCondition	1.3.6.1.4.1.179.0.521			This trap is generated when the connection is switched to another port. The with the trap passed variables correspond to the new active port.
NTF skGeRlmtPortDown	1.3.6.1.4.1.179.0.522			This trap is generated when RLMT detects that a port went logically down.
NTF skGeRlmtPortUp	1.3.6.1.4.1.179.0.523			This trap is generated when RLMT detects that a port went logically up.
NTF skGeRlmtSegmentation	1.3.6.1.4.1.179.0.524			This trap is generated when RLMT works in spanning-tree mode (skGeRlmtMode) and two root bridges are detected, which means a segmentation of net. One of the segments may be isolated from the rest of the net.
skSystems	1.3.6.1.4.1.179.1
skMibs	1.3.6.1.4.1.179.2
skConcMib	1.3.6.1.4.1.179.2.3
skfddiMib	1.3.6.1.4.1.179.2.4
skGeMib	1.3.6.1.4.1.179.2.5
skGeGeneral	1.3.6.1.4.1.179.2.5.1
STR skGeMibVersion	1.3.6.1.4.1.179.2.5.1.1	DisplayString	read-only	The version of this MIB (e.g. v1.0).
INT skGeAction	1.3.6.1.4.1.179.2.5.1.2	INTEGER	read-write	Returns on query 'idle'. A set to 'idle' does nothing. A set to 'force-trap' transmits the trap specified in skGeTrapForceType. 'save-permanent' saves the setable values of this MIB permanently.
INT skGeNumber	1.3.6.1.4.1.179.2.5.1.3	INTEGER	read-only	The number of Gigabit-Ethernet adapters.
skGeTable	1.3.6.1.4.1.179.2.5.1.4		not-accessible	Table for general adapter specific information.
skGeEntry	1.3.6.1.4.1.179.2.5.1.4.1		not-accessible	Entry of skGeTable.
INT skGeIndex	1.3.6.1.4.1.179.2.5.1.4.1.1	INTEGER	read-only	Adapter index (1..n).
INT skGeIfIndex	1.3.6.1.4.1.179.2.5.1.4.1.2	INTEGER	read-only	Stores the corresponding ifIndex of the mib-2 interfaces table. If the value cannot be obtained a '0' is stored.
INT skGePortNumber	1.3.6.1.4.1.179.2.5.1.4.1.3	INTEGER	read-only	Number of ports per adapter.
OID skGeDeviceType	1.3.6.1.4.1.179.2.5.1.4.1.4	OBJECT IDENTIFIER	read-only	Returns the object identifier of the NIC. If it is unknown 0.0 is returned.
STR skGeDriverDescr	1.3.6.1.4.1.179.2.5.1.4.1.5	DisplayString	read-only	A description of the driver (e.g. sk98win - Miniport Gigabit-Ethernet driver).
STR skGeDriverVersion	1.3.6.1.4.1.179.2.5.1.4.1.6	DisplayString	read-only	The driver version (e.g. v1.05 beta).
STR skGeHwDescr	1.3.6.1.4.1.179.2.5.1.4.1.7	DisplayString	read-only	A description of the device hardware (e.g. SK-NET Genesis Sx Single Port).
STR skGeHwVersion	1.3.6.1.4.1.179.2.5.1.4.1.8	DisplayString	read-only	The device hardware version. (e.g. v1.2).
OID skGeChipSet	1.3.6.1.4.1.179.2.5.1.4.1.9	OBJECT IDENTIFIER	read-only	Stores the object identifier of the used chip-set.
INT skGeDeviceAction	1.3.6.1.4.1.179.2.5.1.4.1.10	INTEGER	read-write	A set to this variable performs a specific action. A get-request to this variable always returns the idle (1) value. The result of the self-test is stored in skGeTestResult.
INT skGeTestResult	1.3.6.1.4.1.179.2.5.1.4.1.11	INTEGER	read-only	Stores the self test result, which was initiated by skGeDeviceAction. The value is a sum and 2 raised the power of the result is added to the sum. A sum of zero indicates a successful self-test. Result Power unkown 0 (Initial value) tranceiverErr 1 asicErr 2 sensorErr 3 powermgmtErr 4 pciErr 5 macErr 6
INT skGeBusType	1.3.6.1.4.1.179.2.5.1.4.1.12	INTEGER	read-only	Returns the bus type.
INT skGeBusSpeed	1.3.6.1.4.1.179.2.5.1.4.1.13	INTEGER	read-only	Returns the bus speed in MHz (e.g. 33 means a bus speed of 33 MHz). If the value is unknown a 0 is returned.
INT skGeBusWidth	1.3.6.1.4.1.179.2.5.1.4.1.14	INTEGER	read-only	Returns the bus width in bits (e.g. 64 means a bus width of 64 bit). If the value is unknown a 0 is returned.
INT skGeChecksumEntriesNumber	1.3.6.1.4.1.179.2.5.1.5	INTEGER	read-only	Number of entries in skGeCheckSumTable.
skGeChecksumTable	1.3.6.1.4.1.179.2.5.1.6		not-accessible	Table of the adapter hardware checksumming module.
skGeChecksumEntry	1.3.6.1.4.1.179.2.5.1.6.1		not-accessible	Entry of the checksum table.
INT skGeChecksumGeIndex	1.3.6.1.4.1.179.2.5.1.6.1.1	INTEGER	read-only	Index of the adapter.
INT skGeChecksumIndex	1.3.6.1.4.1.179.2.5.1.6.1.2	INTEGER	read-only	Index of the protocol. The indexes have fixed semantics.
CTR skGeChecksumRxOkCts	1.3.6.1.4.1.179.2.5.1.6.1.3	Counter	read-only	Number of received frames for which the protocol checksum verification was successfully performed in hardware.
CTR skGeChecksumRxUnableCts	1.3.6.1.4.1.179.2.5.1.6.1.4	Counter	read-only	Number of received frames for which the protocol checksum verification was left to the protocol.
CTR skGeChecksumRxErrCts	1.3.6.1.4.1.179.2.5.1.6.1.5	Counter	read-only	Number of received frames for which the protocol checksum verification in hardware found an error.
CTR skGeChecksumTxOkCts	1.3.6.1.4.1.179.2.5.1.6.1.6	Counter	read-only	Number of transmitted packets for which the protocol checksum was generated in hardware.
CTR skGeChecksumTxUnableCts	1.3.6.1.4.1.179.2.5.1.6.1.7	Counter	read-only	Number of packets, which could not be sent because the requested generation of the checksum was not possible.
OCT skGeTrapForceType	1.3.6.1.4.1.179.2.5.1.7	OCTET STRING	read-write	Stores the trap number and the value list that is to be transmitted. The transmission is initiated with skGeAction (force-trap). Each field in the octet string consists of a one octet length field followed by the value.
INT skGeTrapDestEntriesNumber	1.3.6.1.4.1.179.2.5.1.8	INTEGER	read-only	Number of entries in skGeTrapDestTable.
skGeTrapDestTable	1.3.6.1.4.1.179.2.5.1.9		not-accessible	Table of trap destination addresses to which the agent will send traps.
skGeTrapDestEntry	1.3.6.1.4.1.179.2.5.1.9.1		not-accessible	Entry of trap destination table.
INT skGeTrapDestIndex	1.3.6.1.4.1.179.2.5.1.9.1.1	INTEGER	read-only	Index of the trap destination table.
IP skGeTrapDestAddress	1.3.6.1.4.1.179.2.5.1.9.1.2	IpAddress	read-only	The destination address to which the agent sends its trap PDUs.
INT skGeTrapFilter	1.3.6.1.4.1.179.2.5.1.10	INTEGER	read-write	The trap filter bits are stored as a sum of powers of 2 (a bit string) in this variable. If the bit is set to 0 the corresponding trap will not be transmitted. If the bit is set to 1 trap transmission is enabled. Trap Power skGeSensorWarningLower 0 skGeSensorWarningUpper 1 skGeSensorErrorLower 2 skGeSensorErrorUpper 3 skGeRlmtChangeThresholdCondition 4 skGeRlmtChangeCondition 5 skGeRlmtPortDown 6 skGeRlmtPortUp 7 skGeRlmtSegmentation 8
INT skGeSensorEntriesNumber	1.3.6.1.4.1.179.2.5.1.13	INTEGER	read-only	Number of entries in skGeSensorTable.
skGeSensorTable	1.3.6.1.4.1.179.2.5.1.14		not-accessible	Table for sensor related values.
skGeSensorEntry	1.3.6.1.4.1.179.2.5.1.14.1		not-accessible	Entry of sensor table.
INT skGeSensorGeIndex	1.3.6.1.4.1.179.2.5.1.14.1.1	INTEGER	read-only	Adapter index which corresponds with skGeIndex.
INT skGeSensorIndex	1.3.6.1.4.1.179.2.5.1.14.1.2	INTEGER	read-only	Index of the sensor. The indexes have fixed semantics.
STR skGeSensorDescr	1.3.6.1.4.1.179.2.5.1.14.1.3	DisplayString	read-only	A textual description of the sensor.
INT skGeSensorType	1.3.6.1.4.1.179.2.5.1.14.1.4	INTEGER	read-only	Stores the sensor type.
INT skGeSensorValue	1.3.6.1.4.1.179.2.5.1.14.1.5	INTEGER	read-only	Stores the current value of the sensor in 10th of degree celsius, milli volts or round per minutes (rpm).
INT skGeSensorWarningThresholdLow	1.3.6.1.4.1.179.2.5.1.14.1.6	INTEGER	read-only	Stores the lower warning threshold of the allowed value range for the monitored unit.
INT skGeSensorWarningThresholdHigh	1.3.6.1.4.1.179.2.5.1.14.1.7	INTEGER	read-only	Stores the upper warning threshold of the allowed value range for the monitored unit.
INT skGeSensorErrorThresholdLow	1.3.6.1.4.1.179.2.5.1.14.1.8	INTEGER	read-only	Stores the lower threshold of the allowed value range for the monitored unit.
INT skGeSensorErrorThresholdHigh	1.3.6.1.4.1.179.2.5.1.14.1.9	INTEGER	read-only	Stores the upper threshold of the allowed value range for the monitored unit.
INT skGeSensorStatus	1.3.6.1.4.1.179.2.5.1.14.1.10	INTEGER	read-only	If a threshold is exceeded this flag will be set.
CTR skGeSensorWarningCts	1.3.6.1.4.1.179.2.5.1.14.1.11	Counter	read-only	If a warning threshold is exceeded this counter will be incremented and a trap will be generated. If the sensor value exceeds the threshold permanently this counter is incremented every two seconds and a trap is generated.
CTR skGeSensorErrorCts	1.3.6.1.4.1.179.2.5.1.14.1.12	Counter	read-only	If a threshold is exceeded this counter will be incremented and a trap will be generated. If the sensor value exceeds the threshold permanently this counter is incremented every second and a trap is generated.
TIK skGeSensorWarningTimeStamp	1.3.6.1.4.1.179.2.5.1.14.1.13	TimeTicks	read-only	Stores the time since the last reboot in hundreds of seconds of the last warning threshold exceed.
TIK skGeSensorErrorTimeStamp	1.3.6.1.4.1.179.2.5.1.14.1.14	TimeTicks	read-only	Stores the time since the last reboot in hundreds of seconds of the last error threshold exceed.
INT skGeStatEntriesNumber	1.3.6.1.4.1.179.2.5.1.15	INTEGER	read-only	Number of entries in the skGeStatTable.
skGeStatTable	1.3.6.1.4.1.179.2.5.1.16		not-accessible	Statistical data of the ports. The number of table entries is stored in skGeStatEntriesNumber.
skGeStatEntry	1.3.6.1.4.1.179.2.5.1.16.1		not-accessible	The first entry (skGeStatIndex) of each adapter card (skGeStatGeIndex) is a virtual one and represents the currently active port with settled statistical data. This means that the number of port specific statistical data entries in this table is by one element higher than the physically provided port number (skGePortNumber).
INT skGeStatGeIndex	1.3.6.1.4.1.179.2.5.1.16.1.1	INTEGER	read-only	Adapter index which corresponds with skGeIndex.
INT skGeStatIndex	1.3.6.1.4.1.179.2.5.1.16.1.2	INTEGER	read-only	The port index. The first index denotes the virtual port entry, which contains settled statistical data. The ports are enumerated from 1..n.
CTR skGeStatTxOkCts	1.3.6.1.4.1.179.2.5.1.16.1.3	Counter	read-only	A count of frames (including short frames, broadcasts frames, and multicast frames) that are successfully transmitted.
CTR skGeStatTxOctetsHighOkCts	1.3.6.1.4.1.179.2.5.1.16.1.4	Counter	read-only	The upper 32 bit count of data and padding octets of frames that are successfully transmitted.
CTR skGeStatTxOctetsLowOkCts	1.3.6.1.4.1.179.2.5.1.16.1.5	Counter	read-only	The lower 32 bit count of data and padding octets of frames that are successfully transmitted.
CTR skGeStatTxBroadcastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.6	Counter	read-only	A count of frames that were successfully transmitted to the broadcast address. Frames transmitted to multicast addresses are not broadcast frames and are excluded.
CTR skGeStatTxMulticastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.7	Counter	read-only	A count of frames that were successfully transmitted to a group destination address other than broadcast.
CTR skGeStatTxUnicastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.8	Counter	read-only	The total number of frames transmitted that were directed to an unicast address. This number does not include frames directed to broadcast or multicast addresses.
CTR skGeStatTxLongFramesCts	1.3.6.1.4.1.179.2.5.1.16.1.9	Counter	read-only	The total number of frames transmitted that are more than the IEEE 802.3 maximum frame size. Typically, 1518 octets if neither the OneLevelVLAN nor TwoLevelVLAN is active, the long frames are defined as more than 1522 octets (excluding framing bits but including FCS octets). If the TowLevelVLAN is active, then long frames are defined as more than 1538 octets (excluding framing bits but including FCS octets).
CTR skGeStatTxBurstCts	1.3.6.1.4.1.179.2.5.1.16.1.10	Counter	read-only	The total number of burst events.
CTR skGeStatTxPFlowCtrlCts	1.3.6.1.4.1.179.2.5.1.16.1.11	Counter	read-only	The total number of Pause Flow-Control frames transmitted, of Opcode=0001.
CTR skGeStatTxFlowCtrlCts	1.3.6.1.4.1.179.2.5.1.16.1.12	Counter	read-only	A count of Flow Control frames transmitted.
CTR skGeStatTxSingleCollisionsCts	1.3.6.1.4.1.179.2.5.1.16.1.13	Counter	read-only	A count of successfully transmitted frames for which transmission is inhibited by exactly one collision.
CTR skGeStatTxMultipleCollisionsCts	1.3.6.1.4.1.179.2.5.1.16.1.14	Counter	read-only	A count of successfully transmitted frames for which transmission is inhibited by more than one collision.
CTR skGeStatTxExcessiveCollisionsCts	1.3.6.1.4.1.179.2.5.1.16.1.15	Counter	read-only	A count of frames that due to excessive collisions are not transmitted successfully.
CTR skGeStatTxLateCollisionsCts	1.3.6.1.4.1.179.2.5.1.16.1.16	Counter	read-only	A count of the times that a collision has been detected later than one slot time, from the start of the packet transmission. A late collision is counted twice, i.e., both as a collision and as a lateCollision.
CTR skGeStatTxDeferralCts	1.3.6.1.4.1.179.2.5.1.16.1.17	Counter	read-only	A count of frames whose transmission was delayed on its first attempt because the medium was busy.
CTR skGeStatTxExcessiveDeferralCts	1.3.6.1.4.1.179.2.5.1.16.1.18	Counter	read-only	A count of frames that deferred for an excessive period of time. This counter may only be incremented once per LLC transmission.
CTR skGeStatTxFifoUnderrunCts	1.3.6.1.4.1.179.2.5.1.16.1.19	Counter	read-only	The number of transmit FIFO underrun events.
CTR skGeStatTxCarrierSenseCts	1.3.6.1.4.1.179.2.5.1.16.1.20	Counter	read-only	A count of times that the carrier sense condition was not asserted or was deasserted during the transmission of a frame without collision.
CTR skGeStatTxOctets64Cts	1.3.6.1.4.1.179.2.5.1.16.1.22	Counter	read-only	The total number of frames transmitted that were 64 octets in length (excluding framing bits but including FCS octets).
CTR skGeStatTxOctets127Cts	1.3.6.1.4.1.179.2.5.1.16.1.23	Counter	read-only	The total number of frames transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
CTR skGeStatTxOctets255Cts	1.3.6.1.4.1.179.2.5.1.16.1.24	Counter	read-only	The total number of frames transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
CTR skGeStatTxOctets511Cts	1.3.6.1.4.1.179.2.5.1.16.1.25	Counter	read-only	The total number of frames transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
CTR skGeStatTxOctets1023Cts	1.3.6.1.4.1.179.2.5.1.16.1.26	Counter	read-only	The total number of frames transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
CTR skGeStatTxOctetsMaxCts	1.3.6.1.4.1.179.2.5.1.16.1.27	Counter	read-only	The total number of frames transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). If the OneLevelVLAN is active this statistic counts frames that are between 1024 and 1522 octets (excluding framing bits but including FCS octets). If the TwoLevelVLAN is active, this statistic counts the frames that are between 1024 and 1538 octets (excluding framing bits but including FCS octets).
CTR skGeStatTxSyncCts	1.3.6.1.4.1.179.2.5.1.16.1.28	Counter	read-only	The total number of frames transmitted synchronuously.
CTR skGeStatTxSyncOctetsHighCts	1.3.6.1.4.1.179.2.5.1.16.1.29	Counter	read-only	The upper 32 bit count of synchronuously transmitted octets.
CTR skGeStatTxSyncOctetsLowCts	1.3.6.1.4.1.179.2.5.1.16.1.30	Counter	read-only	The lower 32 bit count of synchronuously transmitted octets.
CTR skGeStatRxOkCts	1.3.6.1.4.1.179.2.5.1.16.1.31	Counter	read-only	A count of frames (including short frames, broadcast frames, and multicast frames) that are successfully received.
CTR skGeStatRxOctetsHighOkCts	1.3.6.1.4.1.179.2.5.1.16.1.32	Counter	read-only	The upper 32 bit count of data and padding octets in frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC sub-layer error.
CTR skGeStatRxOctetsLowOkCts	1.3.6.1.4.1.179.2.5.1.16.1.33	Counter	read-only	The lower 32 bit count of data and padding octets in frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC sub-layer error.
CTR skGeStatRxBroadcastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.34	Counter	read-only	A count of frames that are successfully received and are directed to the broadcast group address. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC sub-layer error.
CTR skGeStatRxMulticastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.35	Counter	read-only	A count of frames that are successfully received and are directed to an active non-broadcast group address. This does not include frames received with frame-too- long, FCS, length or alignment errors, or frames lost due to internal MAC sub-layer error.
CTR skGeStatRxUnicastOkCts	1.3.6.1.4.1.179.2.5.1.16.1.36	Counter	read-only	The total number of good frames received that were directed to any unicast address, as defined by the Counter Exact Address Match Criteria.
CTR skGeStatRxPFlowCtrlCts	1.3.6.1.4.1.179.2.5.1.16.1.37	Counter	read-only	A count of Flow Control frames received with a length- or-type field value equal to the reserved type for 802.3_MAC_Control and an opcode indicating a PAUSE operation.
CTR skGeStatRxFlowCtrlCts	1.3.6.1.4.1.179.2.5.1.16.1.38	Counter	read-only	A count of Flow Control frames received. Flow Control frames are defined as valid frames with a length-or-type field value equal to the reserved type for 802.3_MAC_Control.
CTR skGeStatRxPFlowCtrlErrCts	1.3.6.1.4.1.179.2.5.1.16.1.39	Counter	read-only	A count of Flow Control frames received with standard PAUSE address with a length-or-type field value equal to the reserved type for 802.3_MAC_Control, but without a valid PAUSE Opcode (0001).
CTR skGeStatRxFlowCtrlUnknownCts	1.3.6.1.4.1.179.2.5.1.16.1.40	Counter	read-only	A count of Flow Control frames received that contain an opcode that is not supported by the device. Flow Control frames are defined as valid frames with a length-or-type field value equal to the reserved type for 802.3_MAC_Control and with an opcode for a function that is not supported by the device.
CTR skGeStatRxBurstCts	1.3.6.1.4.1.179.2.5.1.16.1.41	Counter	read-only	The total number of burst events.
CTR skGeStatRxMissedCts	1.3.6.1.4.1.179.2.5.1.16.1.42	Counter	read-only	The total number of events in which frames were missed by the controller due to buffer overflow.
CTR skGeStatRxFramingCts	1.3.6.1.4.1.179.2.5.1.16.1.43	Counter	read-only	The total number of frames received with improper end- of-frame delimiter
CTR skGeStatRxFifoOverflowCts	1.3.6.1.4.1.179.2.5.1.16.1.44	Counter	read-only	The number of receive FIFO overflow events.
CTR skGeStatRxJabberCts	1.3.6.1.4.1.179.2.5.1.16.1.45	Counter	read-only	The total number of frames received that were longer than 1518 octets (excluding framing bits but including FCS octets), and had a bad FCS with an integral number of octets; 1522 octets if OneLevelVLAN is active; 1538 octets if TwoLeveVLAN is active.
CTR skGeStatRxCarrierCts	1.3.6.1.4.1.179.2.5.1.16.1.46	Counter	read-only	An event counter for the number of times the carrier event is longer than the permissible duration.
CTR skGeStatRxIRLengthCts	1.3.6.1.4.1.179.2.5.1.16.1.47	Counter	read-only	A count of frames with a length-or-type field value between the minimum unpadded LLC MAC client data size and the maximum allowed LLC MAC client data size inclusive, that does not match the number of LLC MAC client data octets received. The counter also contains frames with a length-or-type field value less than the minimum unpadded LLC MAC client data size. Note: this error is not generated if length field is between 1 and 45 (as this becomes padding case).
CTR skGeStatRxSymbolCts	1.3.6.1.4.1.179.2.5.1.16.1.48	Counter	read-only	A count of the number of times the receiving media is non-idle (a carrier event) for a period of time greater than or equal to slot-time for half-duplex operation, or greater than or equal to min-frame-size for full-duplex operation, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII.
CTR skGeStatRxShortsCts	1.3.6.1.4.1.179.2.5.1.16.1.49	Counter	read-only	An event counter by one for each carrier event with activity-duration less than short-event-max-time. In the 1000 Mb/s case short-event-max-time is 72 bits (9 octets).
CTR skGeStatRxRuntCts	1.3.6.1.4.1.179.2.5.1.16.1.50	Counter	read-only	A counter for each carrier-event that the octet count is less than 64.
CTR skGeStatRxCextCts	1.3.6.1.4.1.179.2.5.1.16.1.51	Counter	read-only	A counter of received frames with no collision, short, or framing error in which the carrier extension was inadequate.
CTR skGeStatRxTooLongCts	1.3.6.1.4.1.179.2.5.1.16.1.52	Counter	read-only	A count of frames received that exceed the maximum permitted frame size, i.e., 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. The maximum frame length could be 1522 octets if OneLevelVLAN is active or 1538 octets if TwoLevelVLAN is active.
CTR skGeStatRxFCSCts	1.3.6.1.4.1.179.2.5.1.16.1.53	Counter	read-only	A count of received frames that are an integral number of octets in length and do not pass the FCS check. This does not include frames received with frame-too-long, or frame-too-short (frame fragment) error.
CTR skGeStatRxOctets64Cts	1.3.6.1.4.1.179.2.5.1.16.1.55	Counter	read-only	The total number of frames (including bad frames) received that were 64 octets in length (excluding framing bits, but including FCS octets).
CTR skGeStatRxOctets127Cts	1.3.6.1.4.1.179.2.5.1.16.1.56	Counter	read-only	The total number of frames (including bad frames) received that were between 65 and 127 octets in length inclusive (excluding framing bits, but including FCS octets).
CTR skGeStatRxOctets255Cts	1.3.6.1.4.1.179.2.5.1.16.1.57	Counter	read-only	The total number of frames (including bad frames) received that were between 128 and 255 octets in length inclusive (excluding framing bits, but including FCS octets).
CTR skGeStatRxOctets511Cts	1.3.6.1.4.1.179.2.5.1.16.1.58	Counter	read-only	The total number of frames (including bad frames) received that were between 256 and 511 octets in length inclusive (excluding framing bits, but including FCS octets).
CTR skGeStatRxOctets1023Cts	1.3.6.1.4.1.179.2.5.1.16.1.59	Counter	read-only	The total number of frames (including bad frames) received that were between 512 and 1023 octets in length inclusive (excluding framing bits, but including FCS octets).
CTR skGeStatRxOctetsMaxCts	1.3.6.1.4.1.179.2.5.1.16.1.60	Counter	read-only	The total number of frames (including bad frames) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits, but including FCS octets). If the OneLevelVLAN is active, this statistic counts frames that are between 1024 and 1522 octets (excluding framing bits, but including FCS octets). If the TwoLevelVLAN is active, this statistic counts frames that are between 1024 and 1538 octets (excluding framing bits, but including FCS octets).
CTR skGeStatRxLongFramesCts	1.3.6.1.4.1.179.2.5.1.16.1.61	Counter	read-only	The total number of frames received that are greater than the IEEE 802.3 maximum frame size. Typically, 1518 octets if neither the OneLevelVLAN nor TwoLevelVLAN is active, the long frames are defined as more than 1522 octets (excluding framing bits but including FCS octets). If the TowLevelVLAN is active, then long frames are defined as more than 1538 octets (excluding framing bits but including FCS octets).
INT skGeConfEntriesNumber	1.3.6.1.4.1.179.2.5.1.17	INTEGER	read-only	The number of entries in the skGeConfTable.
skGeConfTable	1.3.6.1.4.1.179.2.5.1.18		not-accessible	The table describes the physical port data. The number of table entries is stored in skGeConfEntriesNumber.
skGeConfEntry	1.3.6.1.4.1.179.2.5.1.18.1		not-accessible	The first entry (skGeConfIndex) of each adapter card (skGeConfGeIndex) is a virtual one and represents the active MAC instance with settled statistical data. This means that the number of port specific statistical data entries in this table is by one element higher than the physically provided port number (skGePortNumber).
INT skGeConfGeIndex	1.3.6.1.4.1.179.2.5.1.18.1.1	INTEGER	read-only	Adapter index which corresponds with skGeIndex.
INT skGeConfIndex	1.3.6.1.4.1.179.2.5.1.18.1.2	INTEGER	read-only	The port index. The value is equivalent to skGeStatPortIndex. The ports are enumerated from 1..n. The first entry is the virtual one.
ADR skGeConfPhysCurrentAddr	1.3.6.1.4.1.179.2.5.1.18.1.3	SkGeMACAddress	read-only	The physical address. The first entry of a adapter stores the physical address reported to the operating system. The other entries store the physical addresses of RLMT.
ADR skGeConfPhysFactoryAddr	1.3.6.1.4.1.179.2.5.1.18.1.4	SkGeMACAddress	read-only	The burned in physical address. The first entry of a adapter stores the physical address reported to the operating system. The other entries store the physical addresses of RLMT.
INT skGeConfPMDType	1.3.6.1.4.1.179.2.5.1.18.1.5	INTEGER	read-only	Stores the physical media type of the port.
INT skGeConfConnector	1.3.6.1.4.1.179.2.5.1.18.1.6	INTEGER	read-only	Stores the connector type of the port.
INT skGeConfLinkCap	1.3.6.1.4.1.179.2.5.1.18.1.7	INTEGER	read-only	Indicates which connection modes the port supports. The modes are stored as a sum of powers of 2. Mode Power 0 half-duplex 1 full-duplex 2 auto-half-duplex 3 auto-full-duplex
INT skGeConfLinkMode	1.3.6.1.4.1.179.2.5.1.18.1.8	INTEGER	read-write	Defines in which mode the port should work. The modes half-duplex and full-duplex force the port to work in the corresponding mode. No autonegotiation is performed. The auto modes let the port perform autonegotiation with the capabilities half-duplex, full-duplex or both modes. The sense mode starts with autonegotiation and if failed falls back to full-duplex mode. After the link went down a new sense cycle is started.
INT skGeConfLinkModeStatus	1.3.6.1.4.1.179.2.5.1.18.1.9	INTEGER	read-only	Stores the mode with which the port is currently working. The keyword auto indicates that the link mode was established by autonegotiation. Otherwise the port was forced into the current mode.
INT skGeConfLinkStatus	1.3.6.1.4.1.179.2.5.1.18.1.10	INTEGER	read-only	Stores the link status of the unit. If a link becomes up or down a trap is generated.
INT skGeConfFlowCtrlCap	1.3.6.1.4.1.179.2.5.1.18.1.11	INTEGER	read-only	Indicates which flow control types the port supports.
INT skGeConfFlowCtrlMode	1.3.6.1.4.1.179.2.5.1.18.1.12	INTEGER	read-write	Defines the flow-control type the port should announce during auto-negotiation. If auto-negotiation is disabled flow-control is disabled and settings to this variable have no effect.
INT skGeConfFlowCtrlStatus	1.3.6.1.4.1.179.2.5.1.18.1.13	INTEGER	read-only	Stores the flow-control type the port is currently using.
INT skGeConfPhyOperationCap	1.3.6.1.4.1.179.2.5.1.18.1.14	INTEGER	read-only	Indicates which operation modes the phy supports. The modes are stored as a sum of powers of 2. Mode Power 0 master-slave auto-negotiation 1 master 2 slave
INT skGeConfPhyOperationMode	1.3.6.1.4.1.179.2.5.1.18.1.15	INTEGER	read-write	Defines in which mode the phy should work. The modes master and slave force the port to work in the corresponding mode. No autonegotiation is performed. The auto mode lets the port perform autonegotiation with the capabilities.
INT skGeConfPhyOperationStatus	1.3.6.1.4.1.179.2.5.1.18.1.16	INTEGER	read-only	Stores the operation mode with which the port is currently working.
skGeVpd	1.3.6.1.4.1.179.2.5.2
skGeVpdTable	1.3.6.1.4.1.179.2.5.2.1		not-accessible	This table stores data for easy vpd access.
skGeVpdEntry	1.3.6.1.4.1.179.2.5.2.1.1		not-accessible	Entry of skGeVpdTable.
INT skGeVpdIndex	1.3.6.1.4.1.179.2.5.2.1.1.1	INTEGER	read-only	Adapter index that corresponds to skGeIndex.
INT skGeVpdFreeBytes	1.3.6.1.4.1.179.2.5.2.1.1.2	INTEGER	read-only	Stores the number of free bytes in the read-write area of the VPD RAM.
STR skGeVpdEntryList	1.3.6.1.4.1.179.2.5.2.1.1.3	DisplayString	read-only	Stores a list of the VPD keywords. The elements of the list are separated by a space character (0x20).
skGeVpdValueTable	1.3.6.1.4.1.179.2.5.2.2		not-accessible	This table provides access to the Vital Product Data (VPD).
skGeVpdValueEntry	1.3.6.1.4.1.179.2.5.2.2.1		not-accessible	VPD value table entry. On creation of a new entry: If the key is first set the vpd subsystem will create a new entry with an empty value field. If the value is first set the key must extracted from the oid and key a nd value are then set simultaneously.
INT skGeVpdValueIndex	1.3.6.1.4.1.179.2.5.2.2.1.1	INTEGER	read-only	Adapter index that corresponds to skGeIndex.
STR skGeVpdKey	1.3.6.1.4.1.179.2.5.2.2.1.2	DisplayString	read-write	VPD keyword.
OCT skGeVpdValue	1.3.6.1.4.1.179.2.5.2.2.1.3	OCTET STRING	read-write	Value stored under VPD keyword.
INT skGeVpdAccess	1.3.6.1.4.1.179.2.5.2.2.1.4	INTEGER	read-only	Defines whether the entry is only readable or also writable. Read-only entries cannot be changed or deleted.
INT skGeVpdValid	1.3.6.1.4.1.179.2.5.2.2.1.5	INTEGER	read-write	If the entry is writeable a set to 'invalid' will remove the entry from the VPD. A set to 'valid' will have no effect.
skGeRlmt	1.3.6.1.4.1.179.2.5.3
INT skGeRlmtEntriesNumber	1.3.6.1.4.1.179.2.5.3.1	INTEGER	read-only	Stores the number of skGeRlmtTable entries. The number corresponds to skGeNumber.
skGeRlmtTable	1.3.6.1.4.1.179.2.5.3.2		not-accessible	Table for RLMT (Redundant Link ManagemenT) specific data.
skGeRlmtEntry	1.3.6.1.4.1.179.2.5.3.2.1		not-accessible	Entry of skGeRlmtTable.
INT skGeRlmtIndex	1.3.6.1.4.1.179.2.5.3.2.1.1	INTEGER	read-only	Stores the index of the adapter card that corresponds with this entry. It is identical to skGeIndex.
INT skGeRlmtMode	1.3.6.1.4.1.179.2.5.3.2.1.2	INTEGER	read-write	Stores the working mode of RLMT as a power of 2. Mode Power link-check 0 Always active send-check 1 Sends hello packets spanning-tree 2 Monitors SP packets monitor 3 Monitors other GE-NICs
INT skGeRlmtPortActive	1.3.6.1.4.1.179.2.5.3.2.1.3	INTEGER	read-only	Stores the index of the currently active port. The value 0 indicates that currently no port is active.
INT skGeRlmtPortPreferred	1.3.6.1.4.1.179.2.5.3.2.1.4	INTEGER	read-write	If RLMT evaluates that all links are well working this value is used to decide which port should be used. The value ?0? indicates automatic mode and let RLMT do the decision.
CTR skGeRlmtChangeCts	1.3.6.1.4.1.179.2.5.3.2.1.5	Counter	read-only	Counts the number of times RLMT switched from one port to another which indicates an error.
TIK skGeRlmtChangeTimeStamp	1.3.6.1.4.1.179.2.5.3.2.1.6	TimeTicks	read-only	Stores the time in hundreds of seconds since the last reboot when the connection was switched to another port.
INT skGeRlmtChangeEstimate	1.3.6.1.4.1.179.2.5.3.2.1.7	INTEGER	read-only	Stores the number of port switches per hour.
INT skGeRlmtChangeThreshold	1.3.6.1.4.1.179.2.5.3.2.1.8	INTEGER	read-write	Stores the threshold in number of port switches per hour. If the threshold is exceeded a trap is generated.
INT skGeRlmtPortNumber	1.3.6.1.4.1.179.2.5.3.2.1.9	INTEGER	read-only	Stores the number of physically present ports.
INT skGeRlmtStatEntriesNumber	1.3.6.1.4.1.179.2.5.3.3	INTEGER	read-only	Number of table elements in skGeRlmtStatTable.
skGeRlmtStatTable	1.3.6.1.4.1.179.2.5.3.4		not-accessible	Stores RLMT specific statistical data according to each port.
skGeRlmtStatEntry	1.3.6.1.4.1.179.2.5.3.4.1		not-accessible	Entry of RLMT statistic table.
INT skGeRlmtStatGeIndex	1.3.6.1.4.1.179.2.5.3.4.1.1	INTEGER	read-only	Index of the adapter card.
INT skGeRlmtStatIndex	1.3.6.1.4.1.179.2.5.3.4.1.2	INTEGER	read-only	Index of the physical port.
INT skGeRlmtStatStatus	1.3.6.1.4.1.179.2.5.3.4.1.3	INTEGER	read-only	The working state of the port.
CTR skGeRlmtStatTxHelloCts	1.3.6.1.4.1.179.2.5.3.4.1.4	Counter	read-only	Number of hello packets sent in the send-check mode.
CTR skGeRlmtStatRxHelloCts	1.3.6.1.4.1.179.2.5.3.4.1.5	Counter	read-only	Number of hello packets received in the send-check mode.
CTR skGeRlmtStatTxSpHelloReqCts	1.3.6.1.4.1.179.2.5.3.4.1.6	Counter	read-only	Number of transmitted packets in spanning-tree mode to force a spanning-tree hello packet.
CTR skGeRlmtStatRxSpHelloCts	1.3.6.1.4.1.179.2.5.3.4.1.7	Counter	read-only	Number of the received spanning-tree hello packets in the spanning-tree mode.
INT skGeRlmtMonitorEntriesNumber	1.3.6.1.4.1.179.2.5.3.5	INTEGER	read-only	Number of stations monitored by RLMT.
skGeRlmtMonitorTable	1.3.6.1.4.1.179.2.5.3.6		not-accessible	Table of stations to be monitored by RLMT.
skGeRlmtMonitorEntry	1.3.6.1.4.1.179.2.5.3.6.1		not-accessible	Entry of skGeRlmtMonitorTable.
INT skGeRlmtMonitorGeIndex	1.3.6.1.4.1.179.2.5.3.6.1.1	INTEGER	read-only	Index of the adapter card.
INT skGeRlmtMonitorIndex	1.3.6.1.4.1.179.2.5.3.6.1.2	INTEGER	read-only	Index of the address table entry.
ADR skGeRlmtMonitorAddr	1.3.6.1.4.1.179.2.5.3.6.1.3	SkGeMACAddress	read-write	Physical address of a monitored station.
CTR skGeRlmtMonitorErrCts	1.3.6.1.4.1.179.2.5.3.6.1.4	Counter	read-only	Counts the number of times the redundant link of the monitored station got lost.
TIK skGeRlmtMonitorErrTimeStamp	1.3.6.1.4.1.179.2.5.3.6.1.5	TimeTicks	read-only	Stores the timestamp of the last time the link got lost.
INT skGeRlmtMonitorAdmin	1.3.6.1.4.1.179.2.5.3.6.1.6	INTEGER	read-write	Set to disable stops the monitoring of the remote station.
skNICs	1.3.6.1.4.1.179.3
skFddiNICs	1.3.6.1.4.1.179.3.1
skGeNICs	1.3.6.1.4.1.179.3.2
skGeSxSingleLink	1.3.6.1.4.1.179.3.2.1
skGeSxDualLink	1.3.6.1.4.1.179.3.2.2
skGeLxSingleLink	1.3.6.1.4.1.179.3.2.3
skGeLxDualLink	1.3.6.1.4.1.179.3.2.4
skGeCxSingleLink	1.3.6.1.4.1.179.3.2.5
skGeCxDualLink	1.3.6.1.4.1.179.3.2.6
skGeTxSingleLink	1.3.6.1.4.1.179.3.2.7
skGeTxDualLink	1.3.6.1.4.1.179.3.2.8
skChipSets	1.3.6.1.4.1.179.4
skGeXMAC11800FP	1.3.6.1.4.1.179.4.1

RFC description

MIB module for managing Gigabit Ethernet interfaces on SK (Sakura/specialized) network equipment. Provides objects for configuring and monitoring high-speed Ethernet port parameters and statistics.

Start monitoring SysKonnect Gigabit Ethernet network adapters, servers/workstations with SysKonnect NICs (driver/firmware identification) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SK-GE-MIB

What Is SK-GE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description