SONOMASYSTEMS-SONOMA-ETHERNET-MIB

All MIBs › SONOMASYSTEMS-SONOMA-ETHERNET-MIB

Category: Ethernet and LAN Management, SonomaSystems ATM WAN Management

Description: Manages SonomaSystems Sonoma Ethernet interface configuration, link status, and traffic statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SONOMASYSTEMS-SONOMA-ETHERNET-MIB?

SONOMASYSTEMS-SONOMA-ETHERNET-MIB is a vendor MIB from Sonoma Systems for managing Ethernet interfaces on Sonoma-branded network equipment (likely telecom access/transport gear). It is intended to expose Ethernet port configuration, link status, and traffic statistics for the device's Ethernet interfaces. Its monitoring purpose would center on interface hardware/link status: administrators would check link up/down state, duplex/speed configuration, and traffic counters to spot a failed or congested Ethernet port. No sample objects were available in this batch to ground specific object names, so exact table/object naming can't be confirmed, but it likely depends conceptually on the standard IF-MIB interface model. It would be deployed wherever Sonoma Systems equipment provides Ethernet connectivity within a carrier or enterprise network. Engineers can download the SONOMASYSTEMS-SONOMA-ETHERNET-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SONOMASYSTEMS-SONOMA-ETHERNET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Sonoma Systems network equipment

Monitoring Examples

No sample objects were provided for this MIB in the batch data, so a concrete monitoring scenario using real object names cannot be responsibly constructed. Conceptually, an operator would expect to poll per-port link status and traffic counters analogous to a standard Ethernet interface table, but without grounded object names this remains inferred rather than confirmed.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From SONOMASYSTEMS-SONOMA-MIB

sonomaLAN

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
sonomaEthernet	1.3.6.1.4.1.2926.25.5.1
ethernetAdapterGroup	1.3.6.1.4.1.2926.25.5.1.1
enetSMCGroup	1.3.6.1.4.1.2926.25.5.1.1.1
enetSMCConfigTable	1.3.6.1.4.1.2926.25.5.1.1.1.1		not-accessible	A table of Ethernet physical port configuration parameters.
enetSMCConfigEntry	1.3.6.1.4.1.2926.25.5.1.1.1.1.1		not-accessible	An entry in the enetSMC port table.
INT enetSMCConfigIndex	1.3.6.1.4.1.2926.25.5.1.1.1.1.1.1	INTEGER	read-only	The value of the index uniquely specifies the physical port number to which this entry is applicable.
INT enetSMCConfigLineSpeed	1.3.6.1.4.1.2926.25.5.1.1.1.1.1.2	INTEGER	read-write	The line speed configured for this adapter. Auto and 100 Mbit are only valid for the 9332 card.
INT enetSMCConfigInterface	1.3.6.1.4.1.2926.25.5.1.1.1.1.1.3	INTEGER	read-write	This type of interface which is configured on this adapter. Setting the value to aui (1) is an invalid operation for interfaces which only support twistedPair or utp. Where: aui - Attachment Unit Interface, utp - Unshielded Twisted Pair.
INT enetSMCConfigMode	1.3.6.1.4.1.2926.25.5.1.1.1.1.1.4	INTEGER	read-write	Indicates which duplex mode is configured on this interface.
enetSMCStatsTable	1.3.6.1.4.1.2926.25.5.1.1.1.2		not-accessible	A table of Ethernet physical port statistics parameters.
enetSMCStatsEntry	1.3.6.1.4.1.2926.25.5.1.1.1.2.1		not-accessible	An entry in the enetSMC port table.
INT enetSMCStatsIndex	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.1	INTEGER	read-only	The value of the index uniquely specifies the physical port number to which this entry is applicable.
CTR enetSMCSQEErrors	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.2	Counter	read-only	The number of SQE/Heartbeat errors detected.
CTR enetSMCRxMissedFrames	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.3	Counter	read-only	The number of receive frames missed because no buffers were available to accept the incoming data.
CTR enetSMCRetries	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.4	Counter	read-only	Total number of transmission retries by this station on the attached LAN.
CTR enetSMCCollisions	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.5	Counter	read-only	Total collisions detected on the attached LAN.
CTR enetSMCRunts	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.6	Counter	read-only	Total number of runts detected on the attached LAN.
CTR enetSMCFRAMorCRCErrors	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.7	Counter	read-only	Total number of Framing or CRC errors detected on LAN.
CTR enetSMCTxDeferrals	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.8	Counter	read-only	The total number of TX deferrals encountered on the LAN segment.
CTR enetSMCLateCollisions	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.9	Counter	read-only	Total number of late collisions encountered during transmission by this port.
CTR enetSMCLossofCarrierErrors	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.10	Counter	read-only	Total number of loss of carrier errors encountered by this port.
CTR enetSMCRetryErrors	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.11	Counter	read-only	Total number of TX retry limit errors encountered during transmission by this port.
CTR enetSMCNoOfLinkResets	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.18	Counter	read-only	This is the number of link resets which have occurred since the last reinitialization of the unit.
INT enetSMCLastLinkResetReason	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.19	INTEGER	read-only	This object gives the reason code for the last reset which occurred on this LAN physical link. A value of noReason(1) is returned if the link has not reset. A value of management(2) is returned when a link reset has been caused by a management protocol (either SNMP or by LMS). A value of deviceReset(3) is returned if the link reset was caused by a hardware failure. A value of cableDrop(4) is returned when the link reset was caused by a missing or faulty cable.
INT enetSMCTimeSinceLastLinkReset	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.20	INTEGER	read-only	This is the time, in seconds, since the last link reset.
CTR enetSMCRxPackets	1.3.6.1.4.1.2926.25.5.1.1.1.2.1.21	Counter	read-only	This is the number of packets received on this link by the device driver.
enetSMCStatusTable	1.3.6.1.4.1.2926.25.5.1.1.1.3		not-accessible	A table of Ethernet physical port status parameters.
enetSMCStatusEntry	1.3.6.1.4.1.2926.25.5.1.1.1.3.1		not-accessible	An entry in the enetSMC port status table.
INT enetSMCLineSpeed	1.3.6.1.4.1.2926.25.5.1.1.1.3.1.1	INTEGER	read-only	Indicates the current line speed.
INT enetSMCLineMode	1.3.6.1.4.1.2926.25.5.1.1.1.3.1.2	INTEGER	read-only	Indicates the current duplex mode on this interface.
INT enetSMCLineInterface	1.3.6.1.4.1.2926.25.5.1.1.1.3.1.3	INTEGER	read-only	Indicate the interface as detected.

RFC description

Tracks Sonoma Ethernet adapter SMC port configuration and performance statistics on Sonoma access platforms.

Start monitoring Sonoma Systems network equipment (Ethernet port link/traffic status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SONOMASYSTEMS-SONOMA-ETHERNET-MIB

What Is SONOMASYSTEMS-SONOMA-ETHERNET-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description