SDH-ETS-MIB

All MIBs › SDH-ETS-MIB

Organization: SAGEM-Tolbiac drd/ddp/tmhd

Last Updated: 2002-05-22

Category: Microwave Radio - SAGEM

Description: Manages SAGEM SDH synchronous transport equipment configuration and performance monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SDH-ETS-MIB?

SDH-ETS-MIB is a SAGEM-Tolbiac (drd/ddp/tmhd division) proprietary MIB (per ETSI ETS 300 304, built on EQUIPMENT-MIB/SAGEM-DR-MIB, referenced by XCON-MIB for cross-connections) defining the SDH transmission portion of network-element equipment. Its SPI (SDH Physical Interface) TTP (Trail Termination Point) table, keyed by index, records STM level, type, name, board index/access, monitor/failure/severity settings, loopback, LOS (Loss of Signal), and TF (Transmission Failure), while a companion RS (Regenerator Section) TTP table records monitor/name/failure/severity, EOW mode, and E1/F1 source pointers. As a status/configuration MIB it lets an administrator confirm SDH termination-point alarm severity and loopback state on a SAGEM SDH network element. It is deployed on SAGEM-Tolbiac SDH transmission network-element equipment. Engineers can download the SDH-ETS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SDH-ETS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SAGEM-Tolbiac SDH transmission network-element equipment

Monitoring Examples

An administrator checks spiTTPFailure and spiTTPLos to diagnose a signal-loss condition on a SAGEM SDH network element's termination point.

What Can Be Monitored

SDH termination-point alarm severity and loopback state

Imported Objects

From EQUIPMENT-MIB

SagemBoolean
Severity

From SAGEM-DR-MIB

sagemDr

MODULE-IDENTITY

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
au4CTP	1.3.6.1.4.1.1038.110.70
SEV au4CTPAis	1.3.6.1.4.1.1038.110.70.2.1.20	Severity	read-write	Severity associed with Alarme Indication Signal failure for administrative unit order 4.
AU4 au4CTPCnxType	1.3.6.1.4.1.1038.110.70.2.1.3	Au4CTPCnxType	read-only	au4 connection Type: none, au4, au4-4c,au4-16c,tu. The 'none' value is used when there is no connection with this output CTP
au4CTPEntry	1.3.6.1.4.1.1038.110.70.2.1		not-accessible	A particular administrative unit order 4 of the equipment.
AU4 au4CTPFailure	1.3.6.1.4.1.1038.110.70.2.1.7	Au4CTPFailure	read-only	Active failures on administrative unit order 4
INT au4CTPIndex	1.3.6.1.4.1.1038.110.70.2.1.1	INTEGER	read-only	A unique value which identify a particular administrative unit order 4. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
SEV au4CTPLom	1.3.6.1.4.1.1038.110.70.2.1.22	Severity	read-write	Severity associed with Loss Of MultiFrame failure for administrative unit order 4.
SEV au4CTPLop	1.3.6.1.4.1.1038.110.70.2.1.21	Severity	read-write	Severity associed with Loss Of Pointer failure for administrative unit order 4.
SAG au4CTPMonitor	1.3.6.1.4.1.1038.110.70.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this administrative unit order 4.
STR au4CTPName	1.3.6.1.4.1.1038.110.70.2.1.4	DisplayString	read-write	A text string which identifies the particular entry among the administrative unit order 4 entries.
INT au4CTPNumber	1.3.6.1.4.1.1038.110.70.1	INTEGER	read-only	Number of administrative unit order 4 in equipment.
SEV au4CTPSeverity	1.3.6.1.4.1.1038.110.70.2.1.8	Severity	read-only	A reference to failure severity for administrative unit order 4.
CTP au4CTPStatus	1.3.6.1.4.1.1038.110.70.2.1.2	CTPStatus	read-only	au4 connection point Status: free or used. The 'free' value is used when there is no connection with this output CTP
au4CTPTable	1.3.6.1.4.1.1038.110.70.2		not-accessible	List of administrative unit order 4 in equipment which are availables for new connection or used in connection. In that case, an indication on the connection type is set into the au4CTPCnxType Variable. All au4 CTP, which are made up of lower connection level (tu3 or tu12), are set to 'used' value with 'tu' type connection indication .
bandwidth	1.3.6.1.4.1.1038.110.190
INT bandwidthAdminStatus	1.3.6.1.4.1.1038.110.190.2.1.7	INTEGER	read-write	The desired state of the Vc. The testing(3) state indicates that no operational packets can be passed.
INT bandwidthBoardIndex	1.3.6.1.4.1.1038.110.190.2.1.2	INTEGER	read-only	Index of the Board that supports the bandwidth unit.
bandwidthEntry	1.3.6.1.4.1.1038.110.190.2.1		not-accessible	A particular unit part of a non-sdh card bandwidth.
INT bandwidthIndex	1.3.6.1.4.1.1038.110.190.2.1.1	INTEGER	read-only	A unique value which identify a particular unit of a non-sdh card bandwidth. The value of index is a Vc Index which change when bandwidthSrcType value is modified.
INT bandwidthNextIndex	1.3.6.1.4.1.1038.110.190.2.1.10	INTEGER	read-only	A reference to the next VC into the channel. This field is set to 0 if the VC is not associated to a channel or if it is the last Vc of the channel.
INT bandwidthNumber	1.3.6.1.4.1.1038.110.190.1	INTEGER	read-only	Number of bandwidth units which are available in the equipement. The number of units depends on their type (Vc4, Vc3, Vc12), on the number of Data card and on the bandwidth size which has been configured for this card. For a Data card which is mapped on a STM16, there are 16 Vc4 entries (or 316 Vc3 entries or 6316 Vc12 entries) in the BandwidthTable.
INT bandwidthOperStatus	1.3.6.1.4.1.1038.110.190.2.1.8	INTEGER	read-only	The current operational state of the Vc. The testing(3) state indicates that no operational packets can be passed.
INT bandwidthPrevIndex	1.3.6.1.4.1.1038.110.190.2.1.9	INTEGER	read-only	A reference to the previous VC into the channel. This field is set to 0 if the VC is not associated to a channel or if it is the first Vc of the channel.
INT bandwidthSinkPointer	1.3.6.1.4.1.1038.110.190.2.1.6	INTEGER	read-write	A reference to the object which sends the data flow to this function on unsynchronous port interface side. This pointer corresponds to an index in the channelTable.
NSP bandwidthSinkType	1.3.6.1.4.1.1038.110.190.2.1.5	NspiSrcType	read-write	A reference to the kind of the sink Pointer. Usually the value is Channel.
INT bandwidthSrcPointer	1.3.6.1.4.1.1038.110.190.2.1.4	INTEGER	read-only	this field is set to bandwidthIndex when the unit is used by a channel and set to 0 otherwise. It defines the TTP and CTP index associated to the channel.
NSP bandwidthSrcType	1.3.6.1.4.1.1038.110.190.2.1.3	NspiSrcType	read-write	Define the decomposition level of the bandwidth.
bandwidthTable	1.3.6.1.4.1.1038.110.190.2		not-accessible	List of Bandwidth units in equipment. It represent the bandwidth occupation of each non-sdh card
channel	1.3.6.1.4.1.1038.110.180
INT channelAdminStatus	1.3.6.1.4.1.1038.110.180.2.1.9	INTEGER	read-write	The desired state of the channel. The testing(3) state indicates that no operational packets can be passed.
CHA channelConcat	1.3.6.1.4.1.1038.110.180.2.1.8	ChannelConcat	read-write	The type of Concatenation used within the channel
INT channelDelay	1.3.6.1.4.1.1038.110.180.2.1.12	INTEGER	read-write	This field give the maximum delay (in millisecondes) for receiving virtual concatenated frames. This field is set to 0 when channelConcat is different to virtual(1)
CHA channelEncaps	1.3.6.1.4.1.1038.110.180.2.1.2	ChannelEncaps	read-write	The type of encapsulation used to map Data stream into Sdh containers
channelEntry	1.3.6.1.4.1.1038.110.180.2.1		not-accessible	A particular SDH Channel of the equipment.
CHA channelFailure	1.3.6.1.4.1.1038.110.180.2.1.14	ChannelFailure	read-only	Active failures on channel
INT channelFirstIndex	1.3.6.1.4.1.1038.110.180.2.1.11	INTEGER	read-write	Index of the first Vc in the Channel when it is configured. Otherwise this field is set to 0.
INT channelIndex	1.3.6.1.4.1.1038.110.180.2.1.1	INTEGER	read-only	A unique value which identify a particular SDH Channel. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
SEV channelLoa	1.3.6.1.4.1.1038.110.180.2.1.16	Severity	read-write	Severity associated with Loss Of Alignment failure for channel.
SEV channelLom	1.3.6.1.4.1.1038.110.180.2.1.17	Severity	read-write	Severity associated with Loss Of Multiframe failure for channel.
SAG channelMonitor	1.3.6.1.4.1.1038.110.180.2.1.13	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this channel.
INT channelNbVc12	1.3.6.1.4.1.1038.110.180.2.1.7	INTEGER	read-write	Number of VC12 into the channel.
INT channelNbVc3	1.3.6.1.4.1.1038.110.180.2.1.6	INTEGER	read-write	Number of VC3 into the channel.
INT channelNbVc4	1.3.6.1.4.1.1038.110.180.2.1.5	INTEGER	read-write	Number of VC4 into the channel.
INT channelNumber	1.3.6.1.4.1.1038.110.180.1	INTEGER	read-only	Number of SDH Channels in equipment.
INT channelOperStatus	1.3.6.1.4.1.1038.110.180.2.1.10	INTEGER	read-only	The current operational state of the channel. The testing(3) state indicates that no operational packets can be passed.
SEV channelSeverity	1.3.6.1.4.1.1038.110.180.2.1.15	Severity	read-only	A reference to failure severity for non-sdh physical port.
SEV channelSqm	1.3.6.1.4.1.1038.110.180.2.1.18	Severity	read-write	Severity associated with Sequence Mismatch failure for channel.
channelTable	1.3.6.1.4.1.1038.110.180.2		not-accessible	List of SDH Channels in equipment.
msa	1.3.6.1.4.1.1038.110.60
msaEntry	1.3.6.1.4.1.1038.110.60.2.1		not-accessible	A particular multiplex section adaptation of the equipment.
INT msaIndex	1.3.6.1.4.1.1038.110.60.2.1.1	INTEGER	read-only	Index of a particular entry among the multiplex section adaptation entries.
STR msaName	1.3.6.1.4.1.1038.110.60.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the multiplex section adaptation entries.
INT msaSinkPointer	1.3.6.1.4.1.1038.110.60.2.1.4	INTEGER	read-only	A reference to the object which sends the data flow to this function on synchronous port interface side. In most equipments, this value cannot be changed and points to the MST it is hard wired with.
MSA msaSinkType	1.3.6.1.4.1.1038.110.60.2.1.3	MsaSinkType	read-only	Type of msa sinkPointer: msa or mst
INT msaSrc1Pointer	1.3.6.1.4.1.1038.110.60.2.1.10	INTEGER	read-only	Table index of the object which sends the data flow to this function on equipment side. For STM16: 4 pseudo STM4 (group of 4STM1) identified by their index in msaTable. Theses indexes must be differents to thoses used by the MST Table. For STM4: 4 VC4 identified by their index in vc4Table For STM1: 1 VC4 identified by its index in vc4Table
MSA msaSrc1Type	1.3.6.1.4.1.1038.110.60.2.1.6	MsaSrcType	read-only	Type of msa srcPointer: msa or vc4
INT msaSrc2Pointer	1.3.6.1.4.1.1038.110.60.2.1.11	INTEGER	read-only	A reference to the object which sends the data flow to this function on equipment side. In most equipments, this value cannot be changed and points to the VC4 function it is hard wired with.
MSA msaSrc2Type	1.3.6.1.4.1.1038.110.60.2.1.7	MsaSrcType	read-only	Type of msa srcPointer: msa or vc4
INT msaSrc3Pointer	1.3.6.1.4.1.1038.110.60.2.1.12	INTEGER	read-only	A reference to the object which sends the data flow to this function on equipment side. In most equipments, this value cannot be changed and points to the VC4 function it is hard wired with.
MSA msaSrc3Type	1.3.6.1.4.1.1038.110.60.2.1.8	MsaSrcType	read-only	Type of msa srcPointer: msa or vc4
INT msaSrc4Pointer	1.3.6.1.4.1.1038.110.60.2.1.13	INTEGER	read-only	A reference to the object which sends the data flow to this function on equipment side. In most equipments, this value cannot be changed and points to the VC4 function it is hard wired with.
MSA msaSrc4Type	1.3.6.1.4.1.1038.110.60.2.1.9	MsaSrcType	read-only	Type of msa srcPointer: msa or vc4
STM msaSTMLevel	1.3.6.1.4.1.1038.110.60.2.1.2	STMLevel	read-only	The STM-n level of the multiplex section adaptation.
msaTable	1.3.6.1.4.1.1038.110.60.2		not-accessible	List of multiplex section adaptation in equipment.
msCTP	1.3.6.1.4.1.1038.110.35
msTTP	1.3.6.1.4.1.1038.110.30
INT msTTPE2SrcPointer	1.3.6.1.4.1.1038.110.30.2.1.8	INTEGER	read-only	A reference to the object which sends the data flow to E2 MSOH byte. Usualy E2 carries X21 EOW (engineering order wire) data. The reference is an index in X21 table.Zero indicates not used
SEV msTTPEber	1.3.6.1.4.1.1038.110.30.2.1.20	Severity	read-write	Severity associed with Excecive Bit Error Rate failure for multiplex section terminaison.
msTTPEntry	1.3.6.1.4.1.1038.110.30.2.1		not-accessible	A particular multiplex section terminaison of the equipment.
INT msTTPEOWByteColumn	1.3.6.1.4.1.1038.110.30.2.1.10	INTEGER	read-write	The column determines the SOH byte selected for Engineering Order Wire: SOH is composed of Col [1,9] E2 is on line 9 column 7. Zero indicates EOW not used, value different from 7 means EOW not on E2
INT msTTPEOWByteLine	1.3.6.1.4.1.1038.110.30.2.1.9	INTEGER	read-write	The line determines the SOH byte selected for Engineering Order Wire: SOH starts with 3 lines of RSOH (1,2,3) and finish with 5 lines of MSOH (5,6,7,8,9) E2 is on line 9 column 7. Zero indicates not used, value different from 9 means EOW not on E2
EOW msTTPEOWMode	1.3.6.1.4.1.1038.110.30.2.1.7	EOWMode	read-only	Mode used for EOW: Codir or contradir Master
MST msTTPFailure	1.3.6.1.4.1.1038.110.30.2.1.5	MsTTPFailure	read-only	Active failures on multiplex section terminaison
INT msTTPIndex	1.3.6.1.4.1.1038.110.30.2.1.1	INTEGER	read-only	A unique value which identify a particular synchronous physical interface. The value of this index is always the same as spiTTPIndex
SAG msTTPMonEber	1.3.6.1.4.1.1038.110.30.2.1.11	SagemBoolean	read-write	If the value of this field is true, the eber is monitored and is used as MSP and SETS criterium. If this defect is detected, an ais signal is send downstream and rdi upstream.
SAG msTTPMonitor	1.3.6.1.4.1.1038.110.30.2.1.3	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this multiplex section terminaison.
STR msTTPName	1.3.6.1.4.1.1038.110.30.2.1.4	DisplayString	read-write	A text string which identifies the particular entry among the multiplex section terminaison entries.
PRO msTTPProtectionType	1.3.6.1.4.1.1038.110.30.2.1.2	ProtectionType	read-write	The value of this field indicates the kind of wanted multiplex section protection. The default value is NONE. if value is changed in msp(1) or msSPRing(2) then (if it's possible) an entry is created respectivelly in mspTable or msSPRingTable. But these tables have to be completed to obtain a configured protection. If value is changed in None(0)then the associated entry in mspTable or msSPRingTable is deleted (if it's possible).
SEV msTTPRdi	1.3.6.1.4.1.1038.110.30.2.1.22	Severity	read-write	Severity associed with Remote Defect Indication failure for multiplex section terminaison.
SEV msTTPSd	1.3.6.1.4.1.1038.110.30.2.1.21	Severity	read-write	Severity associed with Signal Degrade failure for multiplex section terminaison.
INT msTTPSdThreshold	1.3.6.1.4.1.1038.110.30.2.1.12	INTEGER	read-write	A Signal Degrade failure is declared if the error block rate is greater than 1E(-mstSdThreshold). The Signal Degrade failure desapeared when the error block rate is less than 1E(1 - mstSdThreshold).
INT msTTPSesThreshold	1.3.6.1.4.1.1038.110.30.2.1.13	INTEGER	read-only	The number of errors above which the second is declared severely errored for this interface/function. This value apply for near and far interface/function
SEV msTTPSeverity	1.3.6.1.4.1.1038.110.30.2.1.6	Severity	read-only	Severity associed with active failures on multiplex section terminaison.
msTTPTable	1.3.6.1.4.1.1038.110.30.2		not-accessible	List of multiplex section terminaison in equipment.
nspiCTP	1.3.6.1.4.1.1038.110.160
nspiCTPEntry	1.3.6.1.4.1.1038.110.160.2.1		not-accessible	A particular non-sdh physical port of the equipment.
INT nspiCTPIndex	1.3.6.1.4.1.1038.110.160.2.1.1	INTEGER	read-only	A unique value which identify a particular non-sdh physical port. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
STR nspiCTPName	1.3.6.1.4.1.1038.110.160.2.1.4	DisplayString	read-write	A text string which identifies the particular entry among the non-sdh physical port entries.
INT nspiCTPNumber	1.3.6.1.4.1.1038.110.160.1	INTEGER	read-only	A unique value which identify a particular non-sdh physical port. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
CTP nspiCTPStatus	1.3.6.1.4.1.1038.110.160.2.1.3	CTPStatus	read-only	nspi connection point Status: free or used. The 'free' value is used when there is no connection with this output CTP
nspiCTPTable	1.3.6.1.4.1.1038.110.160.2		not-accessible	List of non-sdh physical port in equipment.
NSP nspiCTPTTPType	1.3.6.1.4.1.1038.110.160.2.1.2	NspiSrcType	read-only	The type of VC which is associated to the nspi interface.
nspiTTP	1.3.6.1.4.1.1038.110.170
SEV nspiTTPAis	1.3.6.1.4.1.1038.110.170.2.1.21	Severity	read-write	Severity associed with Alarme Indication Signal failure for non-sdh physical port.
INT nspiTTPBoardAcces	1.3.6.1.4.1.1038.110.170.2.1.6	INTEGER	read-only	Friendly Index of the physical acces on the Board that supports the interface
INT nspiTTPBoardIndex	1.3.6.1.4.1.1038.110.170.2.1.5	INTEGER	read-only	Index of the Board that supports the physical acces of this interface
nspiTTPEntry	1.3.6.1.4.1.1038.110.170.2.1		not-accessible	A particular non-sdh physical port of the equipment.
NSP nspiTTPFailure	1.3.6.1.4.1.1038.110.170.2.1.10	NspiTTPFailure	read-only	Active failures on non-sdh physical port
INT nspiTTPIndex	1.3.6.1.4.1.1038.110.170.2.1.1	INTEGER	read-only	A unique value which identify a particular non-sdh physical port. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
NSP nspiTTPLevel	1.3.6.1.4.1.1038.110.170.2.1.3	NspiTTPLevel	read-only	The rate level of the nspi interface.
LOO nspiTTPLoopback	1.3.6.1.4.1.1038.110.170.2.1.14	Loopback	read-write	This field gives the active loopback status on the non-sdh physical port. When its value is `line' the data flow recieved from the port side is sent back to the line. When its value is `equipment' the data flow recieved form equipment side is send back. The field can be set to a particular loopback value, even if there no garantee that the loopback is really done. The real loopback status of the interface must be checked in the response. The loopback can be cleared by the equipment when it cannot remain for any reason.
SEV nspiTTPLos	1.3.6.1.4.1.1038.110.170.2.1.20	Severity	read-write	Severity associed with Loss Of Signal failure for non-sdh physical port.
SAG nspiTTPMonitor	1.3.6.1.4.1.1038.110.170.2.1.9	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this non-sdh physical port.
STR nspiTTPName	1.3.6.1.4.1.1038.110.170.2.1.4	DisplayString	read-write	A text string which identifies the particular entry among the non-sdh physical port entries.
INT nspiTTPNumber	1.3.6.1.4.1.1038.110.170.1	INTEGER	read-only	A unique value which identify a particular non-sdh physical port. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
SEV nspiTTPSeverity	1.3.6.1.4.1.1038.110.170.2.1.11	Severity	read-only	A reference to failure severity for non-sdh physical port.
INT nspiTTPSrcPointer	1.3.6.1.4.1.1038.110.170.2.1.8	INTEGER	read-only	A reference to the object which sends the data flow to this interface. Usually the value is the Index of a vc12, vc3 or vc4.
NSP nspiTTPSrcType	1.3.6.1.4.1.1038.110.170.2.1.7	NspiSrcType	read-only	A reference to the type of object which sends the data flow to this interface. Usually the value is vc12, vc3 or vc4 types.
nspiTTPTable	1.3.6.1.4.1.1038.110.170.2		not-accessible	List of non-sdh physical port in equipment.
NSP nspiTTPType	1.3.6.1.4.1.1038.110.170.2.1.2	NspiTTPType	read-only	The type of media for the nspi interface.
rsCTP	1.3.6.1.4.1.1038.110.25
rsTTP	1.3.6.1.4.1.1038.110.20
INT rsTTPE1SrcPointer	1.3.6.1.4.1.1038.110.20.2.1.9	INTEGER	read-only	A reference to the object which sends the data flow to E1 RSOH byte (index in X21 table) Usualy E1 carries X21 EOW (engineering order wire) data and thus the pointer s value reference a mib X21 port entry. Zero indicates not used
rsTTPEntry	1.3.6.1.4.1.1038.110.20.2.1		not-accessible	A particular regenerator section terminaison of the equipment.
INT rsTTPEOWByteColumn	1.3.6.1.4.1.1038.110.20.2.1.13	INTEGER	read-write	The column determines the SOH byte selected for Engineering Order Wire: SOH is composed of Col [1,9] E1 is on line 2 column 4. Zero indicates EOW not used, value different from 4 means EOW not on E1
INT rsTTPEOWByteLine	1.3.6.1.4.1.1038.110.20.2.1.12	INTEGER	read-write	The line determines the SOH byte selected for Engineering Order Wire: SOH starts with 3 lines of RSOH (1,2,3) and finish with 5 lines of MSOH (5,6,7,8,9) E1 is on line 2 column 4. Zero indicates EOW not used, value different from 2 means EOW not on E1
EOW rsTTPEOWMode	1.3.6.1.4.1.1038.110.20.2.1.8	EOWMode	read-only	Mode used for EOW: Codir or contradir Master
INT rsTTPF1SrcPointer	1.3.6.1.4.1.1038.110.20.2.1.10	INTEGER	read-only	A reference to the object which sends the data flow to F1 RSOH byte.Zero indicates not used
RST rsTTPFailure	1.3.6.1.4.1.1038.110.20.2.1.4	RsTTPFailure	read-only	Active failures on regenerator section terminaison
INT rsTTPIndex	1.3.6.1.4.1.1038.110.20.2.1.1	INTEGER	read-only	A unique value which identify a particular synchronous physical interface. The value of this index is always the same as spiTTPIndex.
SEV rsTTPLof	1.3.6.1.4.1.1038.110.20.2.1.20	Severity	read-write	Severity associed with Loss Of Frame failure for regenerator section terminaison.
SAG rsTTPMonitor	1.3.6.1.4.1.1038.110.20.2.1.2	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this regenerator section terminaison.
STR rsTTPName	1.3.6.1.4.1.1038.110.20.2.1.3	DisplayString	read-write	A text string which identifies the particular entry among the regenerator section terminaison entries.
INT rsTTPSesThreshold	1.3.6.1.4.1.1038.110.20.2.1.11	INTEGER	read-only	The number of errors above which the second is declared severely errored for this interface/function. This value apply for near and far interface/function
SEV rsTTPSeverity	1.3.6.1.4.1.1038.110.20.2.1.5	Severity	read-only	Severity associed active Failure for regenerator section terminaison.
rsTTPTable	1.3.6.1.4.1.1038.110.20.2		not-accessible	List of regenerator section terminaison in equipment.
sdhEts	1.3.6.1.4.1.1038.110			The MIB module defines SDH transmition part of an equipment This MIB use the logical model defined in ETSI ETS 300 304. ETS 300 304 (February 1997) defines the SDH information model for the Network Element. This MIB refers to SHELF-MIB for the definition of the Board that supports the interface. This MIB is refered by XCON-MIB that uses the definition of termination point to create cross connection. This MIB also define configuration of the different SDH blocs such as alarm monitoring and severity and give the current status of the termination point.
spiTTP	1.3.6.1.4.1.1038.110.10
INT spiTTPBoardAcces	1.3.6.1.4.1.1038.110.10.2.1.6	INTEGER	read-only	Friendly Index of the physical acces on the Board that supports the interface
INT spiTTPBoardIndex	1.3.6.1.4.1.1038.110.10.2.1.5	INTEGER	read-only	Index of the Board that supports the physical acces of this interface. This index refers to another MIB that defines the board
spiTTPEntry	1.3.6.1.4.1.1038.110.10.2.1		not-accessible	A particular synchronous physical interface of the equipment.
SPI spiTTPFailure	1.3.6.1.4.1.1038.110.10.2.1.8	SpiTTPFailure	read-only	Active failures on synchronous physical interface
INT spiTTPIndex	1.3.6.1.4.1.1038.110.10.2.1.1	INTEGER	read-only	A unique value which identify a particular synchronous physical interface. The value of this index is a constant value assigned to an entry at equipment design time. It is usualy related to harware. Exemple: For ADR155c equipement index are 1,64,127,190 for STM1 interfaces. For ADR2500c equipement index are: 1,1009,2017,3025,4033,5041,6049,7057 for 8 STM16 or 8 STM4, 1,253,505,757 1009,1261,1513,1765 \| 2017,2269,2521,2773 3025,3277,3529,3781 \| --> for 8 (4*STM1) 4033,4285,4537,4789 5041,5293,5545,5797 \| 6049,6301,6553,6805 7057,7309,7561,7813 \|
LOO spiTTPLoopback	1.3.6.1.4.1.1038.110.10.2.1.10	Loopback	read-write	This field gives the active loopback status on the synchronous physical interface. When its value is `line' the data flow recieved from the port side is sent back to the line. When its value is `equipment' the data flow recieved form equipment side is send back. The field can be set to a particular loopback value, even if there no garantee that the loopback is really done. The real loopback status of the interface must be checked in the response. The loopback can be cleared by the equipment when it cannot remain for any reason.
SEV spiTTPLos	1.3.6.1.4.1.1038.110.10.2.1.20	Severity	read-write	Severity associed with Loss Of Signal failure for synchronous physical interface.
SAG spiTTPMonitor	1.3.6.1.4.1.1038.110.10.2.1.7	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this synchronous physical interface.
STR spiTTPName	1.3.6.1.4.1.1038.110.10.2.1.4	DisplayString	read-write	A text string which identifies the particular entry among the synchronous physical interface entries.
INT spiTTPNumber	1.3.6.1.4.1.1038.110.10.1	INTEGER	read-only	Number of synchronous physical interface in equipment = number of element in spiTTPTable
SEV spiTTPSeverity	1.3.6.1.4.1.1038.110.10.2.1.9	Severity	read-only	Severity associed with active failure for synchronous physical interface.
STM spiTTPStmLevel	1.3.6.1.4.1.1038.110.10.2.1.2	STMLevel	read-only	The STM-n level of the interface.
spiTTPTable	1.3.6.1.4.1.1038.110.10.2		not-accessible	List of synchronous physical interface in equipment.
SEV spiTTPTf	1.3.6.1.4.1.1038.110.10.2.1.21	Severity	read-write	Severity associed with Tranmit Fail failure for synchronous physical interface.
SPI spiTTPType	1.3.6.1.4.1.1038.110.10.2.1.3	SpiTTPType	read-only	The kind of the interface: electrical or optical
tu12CTP	1.3.6.1.4.1.1038.110.140
SEV tu12CTPAis	1.3.6.1.4.1.1038.110.140.2.1.20	Severity	read-write	Severity associed with Alarme Indication Signal failure for tributary unit.
tu12CTPEntry	1.3.6.1.4.1.1038.110.140.2.1		not-accessible	A particular tributary unit of the equipment.
TU1 tu12CTPFailure	1.3.6.1.4.1.1038.110.140.2.1.7	Tu12CTPFailure	read-only	Active failures on tributary unit
INT tu12CTPIndex	1.3.6.1.4.1.1038.110.140.2.1.1	INTEGER	read-only	A unique value which identify a particular tu12.
SEV tu12CTPLop	1.3.6.1.4.1.1038.110.140.2.1.21	Severity	read-write	Severity associed with Loss Of Pointer failure for tributary unit.
SAG tu12CTPMonitor	1.3.6.1.4.1.1038.110.140.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this tributary unit.
STR tu12CTPName	1.3.6.1.4.1.1038.110.140.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the tributary unit entries.
INT tu12CTPNumber	1.3.6.1.4.1.1038.110.140.1	INTEGER	read-only	Number of tributary unit in equipment.
SEV tu12CTPSeverity	1.3.6.1.4.1.1038.110.140.2.1.8	Severity	read-only	A reference to failure severity for tributary unit.
CTP tu12CTPStatus	1.3.6.1.4.1.1038.110.140.2.1.2	CTPStatus	read-only	tu12 connection point Status: free or used. The 'free' value is used when there is no connection with this output CTP
tu12CTPTable	1.3.6.1.4.1.1038.110.140.2		not-accessible	List of tributary unit order 12 in equipment which are availables for new connection or used in the same connection level. In that case, an indication on the connection point Status is set into the tu12CTPStatus Variable. All tu12 CTP, which are involved in a different connection level (tu3 or au4), disappear from this List.
tu3CTP	1.3.6.1.4.1.1038.110.120
SEV tu3CTPAis	1.3.6.1.4.1.1038.110.120.2.1.20	Severity	read-write	Severity associed with Alarme Indication Signal failure for tributary unit.
tu3CTPEntry	1.3.6.1.4.1.1038.110.120.2.1		not-accessible	A particular tributary unit of the equipment.
TU3 tu3CTPFailure	1.3.6.1.4.1.1038.110.120.2.1.7	Tu3CTPFailure	read-only	Active failures on tributary unit
INT tu3CTPIndex	1.3.6.1.4.1.1038.110.120.2.1.1	INTEGER	read-only	Index that identifies the particular entry among the tributary unit entries.
SEV tu3CTPLop	1.3.6.1.4.1.1038.110.120.2.1.21	Severity	read-write	Severity associed with Loss Of Pointer failure for tributary unit.
SAG tu3CTPMonitor	1.3.6.1.4.1.1038.110.120.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this tributary unit.
STR tu3CTPName	1.3.6.1.4.1.1038.110.120.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the tributary unit entries.
INT tu3CTPNumber	1.3.6.1.4.1.1038.110.120.1	INTEGER	read-only	Number of tributary unit in equipment.
SEV tu3CTPSeverity	1.3.6.1.4.1.1038.110.120.2.1.8	Severity	read-only	A reference to failure severity for tributary unit.
CTP tu3CTPStatus	1.3.6.1.4.1.1038.110.120.2.1.2	CTPStatus	read-only	tu3 connection point Status: free or used. The 'free' value is used when there is no connection with this output CTP
tu3CTPTable	1.3.6.1.4.1.1038.110.120.2		not-accessible	List of tributary units order 3 in equipment which are availables for new connection or used in the same connection level. In that case, an indication on the connection point status is set into the tu3CTPStatus Variable. All tu3 CTP, which are involved in different connection level (tu12 or au4), disappear from this List.
vc12TTP	1.3.6.1.4.1.1038.110.150
SAG vc12TTPBidirectionnal	1.3.6.1.4.1.1038.110.150.2.1.17	SagemBoolean	read-write	If set to false the equipment does not send Remote Defect Indication.
vc12TTPEntry	1.3.6.1.4.1.1038.110.150.2.1		not-accessible	A particular virtual container order 12 of the equipment.
VCL vc12TTPFailure	1.3.6.1.4.1.1038.110.150.2.1.7	VcLoFailure	read-only	Active failures on virtual container order 12
INT vc12TTPIndex	1.3.6.1.4.1.1038.110.150.2.1.1	INTEGER	read-only	A unique value which identify a particular virtual container order 12. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
VC1 vc12TTPLabelExpected	1.3.6.1.4.1.1038.110.150.2.1.12	Vc12TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc12. Usualy the value of this field cannot be modified as most equipment use the asynchronous bit multiplexing. For historical reasons the receipt of label `unspecified ' does not produce a Signal Label Mismatch failure.
VC1 vc12TTPLabelReceived	1.3.6.1.4.1.1038.110.150.2.1.14	Vc12TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc12. The value of this field is the actual received signal label for this vc12
VC1 vc12TTPLabelSent	1.3.6.1.4.1.1038.110.150.2.1.13	Vc12TTPSignalLabel	read-write	The signal label indicates the multiplexing structure of the vc12. The value of this field is sent as signal label for the vc12. The unspecified value is used for compatibilty with old sdh equipments. The `unequiped' value actives low order unequiped generator (lug). In this case all 1 signal is inserted down and up stream.
SAG vc12TTPMonitor	1.3.6.1.4.1.1038.110.150.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this virtual container order 12.
STR vc12TTPName	1.3.6.1.4.1.1038.110.150.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the virtual container order 12 entries.
INT vc12TTPNumber	1.3.6.1.4.1.1038.110.150.1	INTEGER	read-only	Number of virtual container order 12 in equipment.
OCT vc12TTPPathTraceExpected	1.3.6.1.4.1.1038.110.150.2.1.9	OCTET STRING	read-write	The path trace is a user string that always follows the vc12. If the value the received path trace does not match this one, a tim (Trail Identifier Mismatch) failure is issued. The value `? ' match all possible received path trace.
OCT vc12TTPPathTraceReceived	1.3.6.1.4.1.1038.110.150.2.1.11	OCTET STRING	read-only	The path trace is a user string that always follows the vc12. The value is the actual path trace received in j2 byte
OCT vc12TTPPathTraceSent	1.3.6.1.4.1.1038.110.150.2.1.10	OCTET STRING	read-write	The path trace is a user string that always follows the vc12. The value of this field is sent in j2 byte as path trace for this vc12. The default value is `all 0'.
SEV vc12TTPPlm	1.3.6.1.4.1.1038.110.150.2.1.23	Severity	read-write	Severity associed with Path Label Mismatch failure for virtual container order 12.
SEV vc12TTPRdi	1.3.6.1.4.1.1038.110.150.2.1.20	Severity	read-write	Severity associed with Remote Defect Indication failure for virtual container order 12.
SEV vc12TTPSd	1.3.6.1.4.1.1038.110.150.2.1.21	Severity	read-write	Severity associed with Signal Degrade failure for virtual container order 12.
INT vc12TTPSdThreshold	1.3.6.1.4.1.1038.110.150.2.1.15	INTEGER	read-write	A Signal Degrade failure is declared if the error block rate is greater than 1E(-SdThreshold). The Signal Degrade failure desapeared when the error block rate is less than 1E(1 - SdThreshold).
INT vc12TTPSesThreshold	1.3.6.1.4.1.1038.110.150.2.1.16	INTEGER	read-only	The number of errors above which the second is declared severely errored for this interface/function. This value apply for near and far interface/function
SEV vc12TTPSeverity	1.3.6.1.4.1.1038.110.150.2.1.8	Severity	read-only	A reference to failure severity for virtual container order 12.
INT vc12TTPSinkPointer	1.3.6.1.4.1.1038.110.150.2.1.2	INTEGER	read-only	A reference to the object which sends the data flow to this function on non-sdh physical port side.
VC1 vc12TTPSinkType	1.3.6.1.4.1.1038.110.150.2.1.3	Vc12TTPSinkType	read-only	A reference to the kind of the sink Pointer
vc12TTPTable	1.3.6.1.4.1.1038.110.150.2		not-accessible	List of virtual container order 12 in equipment.The number of records depends on the kinds of configured boards
SEV vc12TTPTim	1.3.6.1.4.1.1038.110.150.2.1.24	Severity	read-write	Severity associed with Trail Identifier Mismatch failure for virtual container order 12.
SEV vc12TTPUneq	1.3.6.1.4.1.1038.110.150.2.1.22	Severity	read-write	Severity associed with virtual container UNEQuiped failure for virtual container order 12.
vc3TTP	1.3.6.1.4.1.1038.110.130
SAG vc3TTPBidirectionnal	1.3.6.1.4.1.1038.110.130.2.1.17	SagemBoolean	read-write	If set to false the equipment does not send Remote Defect Indication.
vc3TTPEntry	1.3.6.1.4.1.1038.110.130.2.1		not-accessible	A particular virtual container order 3 of the equipment.
VCL vc3TTPFailure	1.3.6.1.4.1.1038.110.130.2.1.7	VcLoFailure	read-only	Active failures on virtual container order 3
INT vc3TTPIndex	1.3.6.1.4.1.1038.110.130.2.1.1	INTEGER	read-only	A unique value which identify a particular virtual container order 3. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
VC3 vc3TTPLabelExpected	1.3.6.1.4.1.1038.110.130.2.1.12	Vc3TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc3. Usualy the value of this field cannot be modified as most equipment use the asynchronous bit multiplexing. For historical reasons the receipt of label `unspecified ' does not produce a Signal Label Mismatch failure.
VC3 vc3TTPLabelReceived	1.3.6.1.4.1.1038.110.130.2.1.14	Vc3TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc3. The value of this field is the actual received signal label for this vc3
VC3 vc3TTPLabelSent	1.3.6.1.4.1.1038.110.130.2.1.13	Vc3TTPSignalLabel	read-write	The signal label indicates the multiplexing structure of the vc3. The value of this field is sent as signal label for the vc3. The unspecified value is used for compatibilty with old sdh equipments. The `unequiped' value actives low order unequiped generator (lug). In this case all 1 signal is inserted down and up stream.
SAG vc3TTPMonitor	1.3.6.1.4.1.1038.110.130.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this virtual container order 3.
STR vc3TTPName	1.3.6.1.4.1.1038.110.130.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the virtual container order 3 entries.
INT vc3TTPNumber	1.3.6.1.4.1.1038.110.130.1	INTEGER	read-only	Number of virtual container order 3 in equipment.
OCT vc3TTPPathTraceExpected	1.3.6.1.4.1.1038.110.130.2.1.9	OCTET STRING	read-write	The path trace is a user string that always follows the vc3. If the value the received path trace does not match this one, a tim (Trail Identifier Mismatch) failure is issued. The value `? ' match all possible received path trace.
OCT vc3TTPPathTraceReceived	1.3.6.1.4.1.1038.110.130.2.1.11	OCTET STRING	read-only	The path trace is a user string that always follows the vc3. The value is the actual path trace received in j1 byte
OCT vc3TTPPathTraceSent	1.3.6.1.4.1.1038.110.130.2.1.10	OCTET STRING	read-write	The path trace is a user string that always follows the vc3. The value of this field is sent in j1 byte as path trace for this vc3. The default value is `all 0'.
SEV vc3TTPPlm	1.3.6.1.4.1.1038.110.130.2.1.23	Severity	read-write	Severity associed with Path Label Mismatch failure for virtual container order 3.
SEV vc3TTPRdi	1.3.6.1.4.1.1038.110.130.2.1.20	Severity	read-write	Severity associed with Remote Defect Indication failure for virtual container order 3.
SEV vc3TTPSd	1.3.6.1.4.1.1038.110.130.2.1.21	Severity	read-write	Severity associed with Signal Degrade failure for virtual container order 3.
INT vc3TTPSdThreshold	1.3.6.1.4.1.1038.110.130.2.1.15	INTEGER	read-write	A Signal Degrade failure is declared if the error block rate is greater than 1E(-SdThreshold). The Signal Degrade failure desapeared when the error block rate is less than 1E(1 - SdThreshold).
INT vc3TTPSesThreshold	1.3.6.1.4.1.1038.110.130.2.1.16	INTEGER	read-only	The number of errors above which the second is declared severely errored for this interface/function. This value apply for near and far interface/function
SEV vc3TTPSeverity	1.3.6.1.4.1.1038.110.130.2.1.8	Severity	read-only	A reference to failure severity for virtual container order 3.
INT vc3TTPSinkPointer	1.3.6.1.4.1.1038.110.130.2.1.2	INTEGER	read-only	A reference to the object which sends the data flow to this function on non-sdh physical port side.
VC3 vc3TTPSinkType	1.3.6.1.4.1.1038.110.130.2.1.3	Vc3TTPSinkType	read-only	A reference to the kind of the sink Pointer
vc3TTPTable	1.3.6.1.4.1.1038.110.130.2		not-accessible	List of virtual container order 3 in equipment.The number of records depends on the kinds of configured boards
SEV vc3TTPTim	1.3.6.1.4.1.1038.110.130.2.1.24	Severity	read-write	Severity associed with Trail Identifier Mismatch failure for virtual container order 3.
SEV vc3TTPUneq	1.3.6.1.4.1.1038.110.130.2.1.22	Severity	read-write	Severity associed with virtual container UNEQuiped failure for virtual container order 3.
vc4TTP	1.3.6.1.4.1.1038.110.100
SAG vc4TTPBidirectionnal	1.3.6.1.4.1.1038.110.100.2.1.19	SagemBoolean	read-write	If set to false the equipment does not send Remote Defect Indication.
vc4TTPEntry	1.3.6.1.4.1.1038.110.100.2.1		not-accessible	A particular virtual container order 4 of the equipment.
VC4 vc4TTPFailure	1.3.6.1.4.1.1038.110.100.2.1.7	Vc4TTPFailure	read-only	Active failures on virtual container order 4
INT vc4TTPIndex	1.3.6.1.4.1.1038.110.100.2.1.1	INTEGER	read-only	A unique value which identify a particular virtual container order 4. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware.
VC4 vc4TTPLabelExpected	1.3.6.1.4.1.1038.110.100.2.1.14	Vc4TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc4. If the signal label received for this vc4 is not null and does not match this field, a Signal Label Mismatch failure is detected. If the received label is null a virtual container UNEQuiped failure is detected.
VC4 vc4TTPLabelReceived	1.3.6.1.4.1.1038.110.100.2.1.16	Vc4TTPSignalLabel	read-only	The signal label indicates the multiplexing structure of the vc4. The value of this field is the actual received signal label for this vc4
VC4 vc4TTPLabelSent	1.3.6.1.4.1.1038.110.100.2.1.15	Vc4TTPSignalLabel	read-write	The signal label indicates the multiplexing structure of the vc4. The value of this field in sent as signal label for the vc4.
SAG vc4TTPMonitor	1.3.6.1.4.1.1038.110.100.2.1.6	SagemBoolean	read-write	When the value of this field is set to false, the failure detection is stopped for this virtual container order 4.
STR vc4TTPName	1.3.6.1.4.1.1038.110.100.2.1.5	DisplayString	read-write	A text string which identifies the particular entry among the virtual container order 4 entries.
INT vc4TTPNumber	1.3.6.1.4.1.1038.110.100.1	INTEGER	read-only	Number of virtual container order 4 in equipment.
OCT vc4TTPPathTraceExpected	1.3.6.1.4.1.1038.110.100.2.1.11	OCTET STRING	read-write	The path trace is a user string that always follows the vc4. If the value the received path trace does not match this one, a tim (Trail Identifier Mismatch) failure is issued. The value `? ' match all possible received path trace.
OCT vc4TTPPathTraceReceived	1.3.6.1.4.1.1038.110.100.2.1.13	OCTET STRING	read-only	The path trace is a user string that always follows the vc4. The value is the actual path trace received in j1 byte
OCT vc4TTPPathTraceSent	1.3.6.1.4.1.1038.110.100.2.1.12	OCTET STRING	read-write	The path trace is a user string that always follows the vc4. The value of this field is sent in j1 byte as path trace for this vc4. The default value is `all 0'.
SEV vc4TTPPlm	1.3.6.1.4.1.1038.110.100.2.1.23	Severity	read-write	Severity associed with Path Label Mismatch failure for virtual container order 4.
SEV vc4TTPRdi	1.3.6.1.4.1.1038.110.100.2.1.20	Severity	read-write	Severity associed with Remote Defect Indication failure for virtual container order 4.
SEV vc4TTPSd	1.3.6.1.4.1.1038.110.100.2.1.21	Severity	read-write	Severity associed with Signal Degrade failure for virtual container order 4.
INT vc4TTPSdThreshold	1.3.6.1.4.1.1038.110.100.2.1.17	INTEGER	read-write	A Signal Degrade failure is declared if the error block rate is greater than 1E(-SdThreshold). The Signal Degrade failure desapeared when the error block rate is less than 1E(1 - SdThreshold).
INT vc4TTPSesThreshold	1.3.6.1.4.1.1038.110.100.2.1.18	INTEGER	read-only	The number of errors above which the second is declared severely errored for this interface/function. This value apply for near and far interface/function
SEV vc4TTPSeverity	1.3.6.1.4.1.1038.110.100.2.1.8	Severity	read-only	A reference to failure severity for virtual container order 4.
INT vc4TTPSinkPointer	1.3.6.1.4.1.1038.110.100.2.1.2	INTEGER	read-only	A reference to the object which sends the data flow to this function on synchronous or unsynchronous port interface side. This pointer corresponds to an index in the msTTPTable or nspiTTPTable.
VC4 vc4TTPSinkType	1.3.6.1.4.1.1038.110.100.2.1.3	Vc4TTPSinkType	read-only	A reference to the kind of the sink Pointer
vc4TTPTable	1.3.6.1.4.1.1038.110.100.2		not-accessible	List of virtual container order 4 in equipment.The number of records depends on the kinds of configured boards
SEV vc4TTPTim	1.3.6.1.4.1.1038.110.100.2.1.25	Severity	read-write	Severity associed with Trail Identifier Mismatch failure for virtual container order 4.
SAG vc4TTPTimDis	1.3.6.1.4.1.1038.110.100.2.1.24	SagemBoolean	read-write	If set to true the equipment does not manage the Tim Failure.
VC4 vc4TTPTraceMode	1.3.6.1.4.1.1038.110.100.2.1.9	Vc4TTPTraceMode	read-write	Configuration of the pathTrace length (1 byte or 16 bytes).
SEV vc4TTPUneq	1.3.6.1.4.1.1038.110.100.2.1.22	Severity	read-write	Severity associed with virtual container UNEQuiped failure for virtual container order 4.

RFC description

Defines SDH transmission path management following ETSI ETS 300 304 standard structure.

Start monitoring SAGEM-Tolbiac SDH transmission network-element equipment (termination-point alarm severity/loopback) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SDH-ETS-MIB

What Is SDH-ETS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description