All MIBs › SHELF-MIB
Organization: SAGEM-Tolbiac drd/ddp/tmhd
Last Updated: 2000-12-06
Category: Microwave Radio - SAGEM
Description:
Manages SAGEM shelf chassis slot configuration, card inventory, and power distribution status.
Imported Objects
From EQUIPMENT-MIB
| SagemBoolean | |
| Severity |
From SAGEM-DR-MIB
| sagemDr | MODULE-IDENTITY |
From SNMPv2-SMI
| Counter32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString |
What Is SHELF-MIB?
SHELF-MIB is a vendor-specific MIB for SAGEM ADR (Access and transmission) equipment, modeling the physical shelf/chassis structure of the device including slot layout, installed card inventory, and power distribution. Its data category is hardware inventory and status: which cards occupy which slots, what type each card is, and the health of the shelf's power feeds. Its monitoring purpose is squarely hardware status tracking, letting an administrator confirm that expected line/service cards are present and recognized in their slots and that shelf power distribution is functioning normally, which is critical on modular access/transmission shelves where a power or slot fault can take down multiple subscriber-facing circuits at once. It is part of SAGEM's broader ADR equipment MIB family and would work alongside interface- and service-specific MIBs covering the traffic carried by those cards. It is deployed in telecom access network sites using SAGEM ADR transmission/access shelf equipment. Engineers can download the SHELF-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SHELF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- SAGEM ADR access/transmission shelf equipment
Monitoring Examples
No sample objects were provided for this module in the available data, so a concrete polling scenario referencing real object names cannot be constructed without inventing unconfirmed names; based on the module description, a shelf/slot/card inventory table with power status objects would be expected but specific object names are not confirmed here.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| shelf | 1.3.6.1.4.1.1038.150 | The MIB module specific for ADR equipment | ||
| SAG adrHotReset | 1.3.6.1.4.1.1038.150.1 | SagemBoolean | read-write | Software hot reset when this variable is set to TRUE |
| led | 1.3.6.1.4.1.1038.150.2 | |||
| INT ledNumber | 1.3.6.1.4.1.1038.150.2.1 | INTEGER | read-only | Number of led in equipment. |
| ledTable | 1.3.6.1.4.1.1038.150.2.2 | not-accessible | List of led in equipment. | |
| ledEntry | 1.3.6.1.4.1.1038.150.2.2.1 | not-accessible | A particular led of the equipment. | |
| INT ledIndex | 1.3.6.1.4.1.1038.150.2.2.1.1 | INTEGER | read-only | A unique value which identify a particular led. |
| INT ledPosition | 1.3.6.1.4.1.1038.150.2.2.1.2 | INTEGER | read-only | A reference to the associated Board on the equipment. |
| LED ledType | 1.3.6.1.4.1.1038.150.2.2.1.3 | LedType | read-only | Type of the Led. |
| LED ledStatus | 1.3.6.1.4.1.1038.150.2.2.1.4 | LedStatus | read-only | Status of this Led. |
| holdTime | 1.3.6.1.4.1.1038.150.3 | |||
| HOL adrFailHoldOffTime | 1.3.6.1.4.1.1038.150.3.1 | HoldTime | read-write | Failure hold off time : the time interval during which the defect is present and the failure is not raised |
| HOL adrFailHoldOnTime | 1.3.6.1.4.1.1038.150.3.2 | HoldTime | read-write | Failure hold on time : the time interval during which the defect is cleared and the failure is not |
| board | 1.3.6.1.4.1.1038.150.20 | |||
| INT boardNumber | 1.3.6.1.4.1.1038.150.20.1 | INTEGER | read-only | Number of board in equipment. |
| boardTable | 1.3.6.1.4.1.1038.150.20.2 | not-accessible | List of board in equipment. | |
| boardEntry | 1.3.6.1.4.1.1038.150.20.2.1 | not-accessible | A particular board of the equipment. | |
| INT boardIndex | 1.3.6.1.4.1.1038.150.20.2.1.1 | INTEGER | read-only | A unique value which identify a particular slot. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to hardware. Each equipment maintain its own pool of values: ex ADR155c : A = 1, B = 2, ... M = 5, Fan = 6 ex ADR2500c: Fan = 1, PSU1 = 2, ...Trib1 = 8, Trib6= 13, Line1 = 14,... Switch2 = 17, Shelf = 18 |
| STR boardSlotName | 1.3.6.1.4.1.1038.150.20.2.1.2 | DisplayString | read-only | A DisplayString which identify the name of a particular slot. Its value is fixed at equipment design time. It is usualy related to hardware ex ADR155c : A, B, ... Fan ex ADR2500c: Fan, CCU, CTRL, PSU1, ... TRIB5, .... SWITCH1, ... |
| INT boardExpectType | 1.3.6.1.4.1.1038.150.20.2.1.3 | INTEGER | read-write | A value which configure the expected type. If used, this one must be equal to one of existent boardListIndex for the considerated board. Otherwise, the value is set to 0. Known types are readable in boardListTable |
| INT boardInsertType | 1.3.6.1.4.1.1038.150.20.2.1.4 | INTEGER | read-only | When the inserted board doesn't match with the expexted board the boardMismatch failure is generated. The type of the card could be found in hardware inventory. |
| STR boardExpectFamily | 1.3.6.1.4.1.1038.150.20.2.1.5 | DisplayString | read-only | Board Family corresponding to the specified expected kind. This value is send by the equipment. ex ADR155c : ex ADR2500c : CTRL, FAN, AUX, CCU, PSU, STM1 OPT, STM1 ERE, STM4 OPT, STM16 OPT, GBETH, SWITCH |
| STR boardInsertFamily | 1.3.6.1.4.1.1038.150.20.2.1.6 | DisplayString | read-only | Board Family corresponding to the type of inserted board. ex ADR155c : ex ADR2500c : CTRL, FAN, AUX, CCU, PSU, STM1 OPT, STM1 ERE, STM4 OPT, STM16 OPT, GBETH, SWITCH |
| SAG boardActive | 1.3.6.1.4.1.1038.150.20.2.1.7 | SagemBoolean | read-write | When the value of this field is set to false, the transmission of this board stop and the board could properly be extracted |
| INT boardFirstPortIndex | 1.3.6.1.4.1.1038.150.20.2.1.8 | INTEGER | read-only | If the card is a card with physical ports, then the value is the first index of a physical interface (SPI, PPI) in the mib SDH-ETS. Else, the value is 0. |
| PRO boardProtectionType | 1.3.6.1.4.1.1038.150.20.2.1.9 | ProtectionType | read-write | The value of this field indicates the kind of wanted card protection. The default value is NONE. if value is changed in cardP(1)then an entry is created in cardpTable. But this table has to be completed (by setting the cardpReliefIndex,...) to obtain a configured protection. if value is changed in None(0)then the associated entry in cardpTable is deleted. Some cards don't accept any protection. In that case, the value of this field will remain to NONE |
| SAG boardMonitor | 1.3.6.1.4.1.1038.150.20.2.1.10 | SagemBoolean | read-write | When the value of this field is set to false, the failure detection is stopped for this board. |
| BOA boardFailure | 1.3.6.1.4.1.1038.150.20.2.1.11 | BoardFailure | read-only | Active failures on board |
| SEV boardSeverity | 1.3.6.1.4.1.1038.150.20.2.1.12 | Severity | read-only | A reference to failure severity for boards. |
| SEV boardMissingSev | 1.3.6.1.4.1.1038.150.20.2.1.13 | Severity | read-write | A reference to failure severity for boards. |
| SEV boardMismatchSev | 1.3.6.1.4.1.1038.150.20.2.1.14 | Severity | read-write | A reference to failure severity for boards. |
| SEV boardDefectiveSev | 1.3.6.1.4.1.1038.150.20.2.1.15 | Severity | read-write | A reference to failure severity for boards. |
| boardList | 1.3.6.1.4.1.1038.150.30 | |||
| INT boardListNumber | 1.3.6.1.4.1.1038.150.30.1 | INTEGER | read-only | Number of entry of the boardList Table |
| boardListTable | 1.3.6.1.4.1.1038.150.30.2 | not-accessible | List of board type able to be managed by this equipment . In order to manage a new type, just insert the board and if the family match with a known family, this table will be expand automaticaly with the new type inserted The XX fist value defined ( with boardSlotName = Shelf = 18 for ADR2500c) is a list all possible type of boardInsertedType. | |
| boardListEntry | 1.3.6.1.4.1.1038.150.30.2.1 | not-accessible | A particular boardList of the equipment. | |
| INT boardListIndex | 1.3.6.1.4.1.1038.150.30.2.1.1 | INTEGER | read-only | A unique value. |
| INT boardListSlot | 1.3.6.1.4.1.1038.150.30.2.1.2 | INTEGER | read-only | A reference to the corresponding Slot. |
| STR boardListType | 1.3.6.1.4.1.1038.150.30.2.1.3 | DisplayString | read-only | In order to manage a new type, just insert the board and if the family match with a known family, this table will be expand automaticaly with the new type inserted. ex ADR155c : ex ADR2500c: 4S1.1, S4.1, L16.2, SWITCH, ... |
| softInv | 1.3.6.1.4.1.1038.150.40 | |||
| INT softInventoryNumber | 1.3.6.1.4.1.1038.150.40.1 | INTEGER | read-only | Number of entry of the softInventory Table |
| softInventoryTable | 1.3.6.1.4.1.1038.150.40.2 | not-accessible | List of software inventory used | |
| softInventoryEntry | 1.3.6.1.4.1.1038.150.40.2.1 | not-accessible | A particular boardList of the equipment. | |
| INT softInventoryIndex | 1.3.6.1.4.1.1038.150.40.2.1.1 | INTEGER | read-only | A unique value. |
| INT softInventoryBoard | 1.3.6.1.4.1.1038.150.40.2.1.2 | INTEGER | read-only | A reference to the corresponding Slot. This variable is needed because some boards have their owns Applicative and Boot codes. |
| STR softInventoryType | 1.3.6.1.4.1.1038.150.40.2.1.3 | DisplayString | read-only | Indication of type software |
| STR softInventoryCode | 1.3.6.1.4.1.1038.150.40.2.1.4 | DisplayString | read-only | Indication of version code |
| STR softInventoryExt | 1.3.6.1.4.1.1038.150.40.2.1.5 | DisplayString | read-only | Indication of extension code. This one is not mandatory. |
| hardInv | 1.3.6.1.4.1.1038.150.50 | |||
| INT hardInventoryNumber | 1.3.6.1.4.1.1038.150.50.1 | INTEGER | read-only | Number of different hardware inventory in equipment. |
| hardInventoryTable | 1.3.6.1.4.1.1038.150.50.2 | not-accessible | List of hardware inventory in equipment. A hardware inventory is a description associed to a particular card | |
| hardInventoryEntry | 1.3.6.1.4.1.1038.150.50.2.1 | not-accessible | A particular tInv of the equipment. | |
| INT hardInventoryIndex | 1.3.6.1.4.1.1038.150.50.2.1.1 | INTEGER | read-only | Index of the inventory entry that corresponds to a particular slot |
| STR hardInventoryBoard | 1.3.6.1.4.1.1038.150.50.2.1.2 | DisplayString | read-only | Family of card inserted in the slot |
| STR hardInventoryDescr | 1.3.6.1.4.1.1038.150.50.2.1.3 | DisplayString | read-only | The content of the inventory: a textual description |
| laser | 1.3.6.1.4.1.1038.150.100 | |||
| INT laserNumber | 1.3.6.1.4.1.1038.150.100.1 | INTEGER | read-only | Number of optical interface in equipment. |
| laserTable | 1.3.6.1.4.1.1038.150.100.2 | not-accessible | List of synchronous physical interface in equipment. | |
| laserEntry | 1.3.6.1.4.1.1038.150.100.2.1 | not-accessible | A particular synchronous physical interface of the equipment. | |
| INT laserIndex | 1.3.6.1.4.1.1038.150.100.2.1.1 | INTEGER | read-only | |
| SAG laserTxEnable | 1.3.6.1.4.1.1038.150.100.2.1.2 | SagemBoolean | read-write | Enable(true) or disable(false) the laser output of the interface. |
| SAG laserALSEnable | 1.3.6.1.4.1.1038.150.100.2.1.3 | SagemBoolean | read-write | Automatic Laser Shutdown enable(true) or disable(false). When enabled, this function cuts the laser output when a los is detected on input signal. |
| SAG laserALSRestart2s | 1.3.6.1.4.1.1038.150.100.2.1.4 | SagemBoolean | read-write | Operator command to start a one shot emission during 2s. |
| SAG laserALSRestart90s | 1.3.6.1.4.1.1038.150.100.2.1.5 | SagemBoolean | read-write | Operator command to start a one shot emission during 90s. |
| eow | 1.3.6.1.4.1.1038.150.120 | |||
| INT eowNumber | 1.3.6.1.4.1.1038.150.120.1 | INTEGER | read-only | Number of EOW port in equipment. |
| eowTable | 1.3.6.1.4.1.1038.150.120.2 | not-accessible | List of EOW port in equipment. | |
| eowEntry | 1.3.6.1.4.1.1038.150.120.2.1 | not-accessible | A particular EOW port of the equipment. | |
| INT eowIndex | 1.3.6.1.4.1.1038.150.120.2.1.1 | INTEGER | read-only | A unique value which identify a particular EOW port. The value of index is a constant assigned to an entry at equipment design time. It is usualy related to harware. |
| STR eowName | 1.3.6.1.4.1.1038.150.120.2.1.2 | DisplayString | read-only | A text string which identifies the particular entry among the EOW port entries. |
| EOW eowSrcType | 1.3.6.1.4.1.1038.150.120.2.1.6 | EOWType | read-write | A reference to the object which sends the data flow to this interface. Usually the value is the oid of a vc12 or a connection. |
| INT eowSrcPtr | 1.3.6.1.4.1.1038.150.120.2.1.7 | INTEGER | read-write | A reference to the object which sends the data flow to this interface. Usually the value is the oid of a vc12 or a connection. |
| EOW eowSinkType | 1.3.6.1.4.1.1038.150.120.2.1.8 | EOWType | read-write | A reference to the object which sends the data flow to this interface. Usually the value is the oid of a vc12 or a connection. |
| INT eowSinkPtr | 1.3.6.1.4.1.1038.150.120.2.1.9 | INTEGER | read-write | A reference to the object which sends the data flow to this interface. Usually the value is the oid of a vc12 or a connection. |
| EOW eowClockMode | 1.3.6.1.4.1.1038.150.120.2.1.10 | EOWClockMode | read-write | Select the direction of the two external synchronisation lines. |
RFC description
SAGEM ADR equipment shelf management MIB covering hardware modules, board configuration, and system monitoring.
Start monitoring SAGEM ADR access/transmission shelf equipment (slot/card inventory and power-feed status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.