S5-CHASSIS-MIB

All MIBs › S5-CHASSIS-MIB

Organization: Avaya

Last Updated: 2015-04-07

Category: Avaya BayStack Ethernet Management

Description: Manages Avaya BayStack chassis hardware components including slots, modules, and power supplies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is S5-CHASSIS-MIB?

S5-CHASSIS-MIB is a Nortel/Avaya BayStack MIB covering the S5000 series chassis-based switches, providing chassis-level hardware identity and change-tracking objects. It exposes chassis type, description, location/contact, hardware version, and serial number, along with counters tracking physical, attachment, and configuration changes over time. Its monitoring value is hardware inventory and hardware-change detection: the physical and attachment change counters act as a proxy for module or power supply insertion/removal events, letting an admin infer when chassis hardware has been altered without a dedicated trap. It works together with S5-CHASSIS-TRAP-MIB, which defines the corresponding trap notifications for these same chassis events. It is typically deployed on Nortel/Avaya BayStack or Passport chassis switches in enterprise network closets and data centers. Engineers can download the S5-CHASSIS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in S5-CHASSIS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Avaya/Nortel BayStack S5000 series chassis switches

Monitoring Examples

An admin polls s5ChasType, s5ChasSerNum, and s5ChasVer to inventory chassis hardware and its version, watches s5ChasGblPhysChngs and s5ChasGblPhysLstChng to detect when a module or power supply was physically inserted or removed, and monitors s5ChasGblConfChngs to catch unexpected or unauthorized configuration changes on the chassis.

What Can Be Monitored

chassis type and description
chassis serial number
chassis hardware/firmware version
physical component change count
configuration change count
chassis location/contact info

Imported Objects

From IF-MIB

InterfaceIndex

From IPV6-TC

Ipv6Address
Ipv6AddressPrefix

From S5-ROOT-MIB

s5Chassis

OBJECT-IDENTITY

From S5-TCS-MIB

AttId
LocChan

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
TruthValue

How to Use in IPNetwork Monitor

Example using s5ChasGblPhysChngs OID:

Select an Avaya/Nortel BayStack S5000 series chassis switch (chassis identity/hardware-change counters) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type s5ChasGblPhysChngs into the Find box to locate it in the OID tree, then select it and click OK. The total number of physical changes (i.e., an addition or removal of a component or sub-component) that have been detected in the chassis since cold/warm start of the agent. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
s5ChasGen	1.3.6.1.4.1.45.1.6.3.1
OID s5ChasType	1.3.6.1.4.1.45.1.6.3.1.1	OBJECT IDENTIFIER	read-only	The chassis type. This is 'what kind of box' is being managed. The values are defined under s5ChasTypeVal in the Registration MIB.
STR s5ChasDescr	1.3.6.1.4.1.45.1.6.3.1.2	DisplayString	read-only	A description of the chassis. The value is a zero length string if no information is available.
STR s5ChasLocation	1.3.6.1.4.1.45.1.6.3.1.3	DisplayString	read-write	The physical location of the chassis (e.g., 'fourth floor wiring closet in building A'). The value is a zero length string if no information is available. Note: this object is different from sysLocation in MIB-II. However, an agent may use this value for sysLocation if none is configured in the the agent.
STR s5ChasContact	1.3.6.1.4.1.45.1.6.3.1.4	DisplayString	read-write	The textual identification of the contact person for the chassis, together with information on how to contact this person. The value is a zero length string if no information is available. Note: this object is different from sysContact in MIB-II. However, an agent may use this value for sysContact if none is configured in the agent.
STR s5ChasVer	1.3.6.1.4.1.45.1.6.3.1.5	DisplayString	read-only	The version of the chassis in the form 'major.minor.maintenance[letters]'. If the version is unknown or not available then the value should be a zero length string.
STR s5ChasSerNum	1.3.6.1.4.1.45.1.6.3.1.6	DisplayString	read-only	The serial number of the chassis. If the serial number is unknown or unavailable then the value should be a zero length string.
C32 s5ChasGblPhysChngsEx	1.3.6.1.4.1.45.1.6.3.1.7	Counter32	read-only	The total number of physical changes (i.e., an addition or removal of a component or sub-component) that have been detected in the chassis since cold/warm start of the agent.
TIK s5ChasGblPhysLstChng	1.3.6.1.4.1.45.1.6.3.1.8	TimeTicks	read-only	The value of sysUpTime when the last physical change (i.e., addition or removal of a module or sub-module) was detected in the chassis. If none have been detected since cold/warm start of the agent, then the value is zero.
C32 s5ChasGblAttChngs	1.3.6.1.4.1.45.1.6.3.1.9	Counter32	read-only	The total number of attachment changes across all boards in the chassis that have been detected since cold/warm start of the agent.
TIK s5ChasGblAttLstChng	1.3.6.1.4.1.45.1.6.3.1.10	TimeTicks	read-only	The value of sysUpTime when the last attachment change on any board in the chassis was detected. If none have been detected since cold/warm start of the agent, then the value is zero.
C32 s5ChasGblConfChngs	1.3.6.1.4.1.45.1.6.3.1.11	Counter32	read-only	The total number of configuration changes (other than attachment changes, or physical additions or removals) across all boards in the chassis that have been detected since cold/warm start of the agent.
TIK s5ChasGblConfLstChng	1.3.6.1.4.1.45.1.6.3.1.12	TimeTicks	read-only	The value of sysUpTime when the last configuration change (other than attachment changes, or physical additions or removals) on any board in the chassis was detected. If none have been detected since cold/warm start of the agent, then the value is zero.
s5ChasGrp	1.3.6.1.4.1.45.1.6.3.2
s5ChasGrpTable	1.3.6.1.4.1.45.1.6.3.2.1		not-accessible	A table that contains information about each group that can contain chassis components.
s5ChasGrpEntry	1.3.6.1.4.1.45.1.6.3.2.1.1		not-accessible	A row in the group table. Rows can not be created or deleted via SNMP requests. The number of entries is determined by the physical construction of the chassis.
I32 s5ChasGrpIndx	1.3.6.1.4.1.45.1.6.3.2.1.1.1	Integer32	read-only	The index of the group.
OID s5ChasGrpType	1.3.6.1.4.1.45.1.6.3.2.1.1.2	OBJECT IDENTIFIER	read-only	The type of the group. The group type determines the types of items that can be plugged into the positions in the group. The groups are defined under s5ChasGrpTypeVal in the Registration MIB.
STR s5ChasGrpDescr	1.3.6.1.4.1.45.1.6.3.2.1.1.3	DisplayString	read-only	The description of the group. If not available, the value is a zero length string.
I32 s5ChasGrpMaxEnts	1.3.6.1.4.1.45.1.6.3.2.1.1.4	Integer32	read-only	The maximum number of entries in the group. If not available, a value of -1 is returned.
I32 s5ChasGrpNumEnts	1.3.6.1.4.1.45.1.6.3.2.1.1.5	Integer32	read-only	The current number of entries in the group. If not available, a value of -1 is returned.
C32 s5ChasGrpPhysChngs	1.3.6.1.4.1.45.1.6.3.2.1.1.6	Counter32	read-only	The total number of physical changes (i.e., an addition or removal of a component or sub-component) that have been detected in the group since cold/warm start of the agent.
TIK s5ChasGrpPhysLstChng	1.3.6.1.4.1.45.1.6.3.2.1.1.7	TimeTicks	read-only	The value of sysUpTime that the last physical change (i.e., addition or removal of a module or sub-module) was detected in the group. If none have been detected since cold/warm start of the agent, then the value is zero.
I32 s5ChasGrpEncodeFactor	1.3.6.1.4.1.45.1.6.3.2.1.1.8	Integer32	read-only	The multiplication factor used in encoding the component index of a component in the group. The component index for any group should be determined in conjunction with this object for that group. A value of 1 indicates 'no encoding'. Stackable platforms: The component index is encoded using the following formula: Component Index = (Unit# * s5ChasGrpEncodeFactor) + Module# Where: Unit# is obtained from s5ChasComIndx for the Unit Group, and Module# is the module number in a unit starting from 1 and increases in a left-to-right and bottom-to-top fashion. NonStackable platforms: These NMMs like 5310, 5510 will always return a value of 1 for this object. Encoding/decoding should not be performed in this case.
s5ChasCom	1.3.6.1.4.1.45.1.6.3.3
s5ChasComTable	1.3.6.1.4.1.45.1.6.3.3.1		not-accessible	A table that contains information about each chassis level component and sub-component.
s5ChasComEntry	1.3.6.1.4.1.45.1.6.3.3.1.1		not-accessible	A row in the component/sub-component table. Rows can not be created or deleted via SNMP requests. Entries are created and deleted when components or sub-components are inserted or removed from the chassis.
I32 s5ChasComGrpIndx	1.3.6.1.4.1.45.1.6.3.3.1.1.1	Integer32	read-only	The index of the chassis level group which contains this component.
I32 s5ChasComIndx	1.3.6.1.4.1.45.1.6.3.3.1.1.2	Integer32	read-only	The index of the component in the group. For example, for modules in the 'board' group, this is the slot number.
I32 s5ChasComSubIndx	1.3.6.1.4.1.45.1.6.3.3.1.1.3	Integer32	read-only	If this table entry (i.e. table row) describes a component, then the value is zero. Otherwise, this table entry describes a sub-component and this is the index of the sub-component.
OID s5ChasComType	1.3.6.1.4.1.45.1.6.3.3.1.1.4	OBJECT IDENTIFIER	read-only	The type of component/sub-component. The values are defined under s5ChasComTypeVal in the Registration MIB.
STR s5ChasComDescr	1.3.6.1.4.1.45.1.6.3.3.1.1.5	DisplayString	read-only	A description of the component/sub-component. If not available, the value is a zero length string.
STR s5ChasComVer	1.3.6.1.4.1.45.1.6.3.3.1.1.6	DisplayString	read-only	The version number of the component/sub-component. If not available, the value is a zero length string.
STR s5ChasComSerNum	1.3.6.1.4.1.45.1.6.3.3.1.1.7	DisplayString	read-only	The serial number of the component/sub-component. If not available, the value is a zero length string.
TIK s5ChasComLstChng	1.3.6.1.4.1.45.1.6.3.3.1.1.8	TimeTicks	read-only	The value of sysUpTime when it was detected that the component/sub-component was added to the chassis. If this has not occurred since the cold/warm start of the agent, then the value is zero.
INT s5ChasComAdminState	1.3.6.1.4.1.45.1.6.3.3.1.1.9	INTEGER	read-write	The desired state of the component/sub-component. The values that are read-only are: other(1)......currently in some other state notAvail(2)...actual value is not available The possible values that can be read and written are: disable(3)...disable operation enable(4)....enable operation reset(5).....reset component test(6)......start self test of component, with the result to be normal(5), warning(8), nonFatalErr(9), or fatalErr(10) in object s5ChasComOperState The allowable (and meaningful) values are determined by the component type.
INT s5ChasComOperState	1.3.6.1.4.1.45.1.6.3.3.1.1.10	INTEGER	read-only	The current operational state of the component. The possible values are: other(1).........some other state notAvail(2)......state not available removed(3).......component removed disabled(4)......operation disabled normal(5)........normal operation resetInProg(6)...reset in progress testing(7).......doing a self test warning(8).......operating at warning level nonFatalErr(9)...operating at error level fatalErr(10).....error stopped operation notConfig(11)....module needs to be configured obsoleted(12)...module is obsoleted but in the chassis The allowable (and meaningful) values are determined by the component type.
I32 s5ChasComMaxSubs	1.3.6.1.4.1.45.1.6.3.3.1.1.11	Integer32	read-only	The potential number of sub-components that can be attached to the component. A value of zero means none. A value of -1 indicates that no component information is available. The actual number of installed sub-components is found in s5ChasComNumSubs. If this entry is a sub-component, then this object has a value of zero.
I32 s5ChasComNumSubs	1.3.6.1.4.1.45.1.6.3.3.1.1.12	Integer32	read-only	The actual number of sub-components that are attached to the component. A value of zero means none. A value of -1 indicates that no component information is available. The potential number of sub-components that can be installed is found in s5ChasComMaxSubs. If this entry is a sub-component, then this object has the value of zero.
I32 s5ChasComRelPos	1.3.6.1.4.1.45.1.6.3.3.1.1.13	Integer32	read-only	This object describes the position of each component in the unit group relative to each other. Components in the unit group are numbered in the ascending order with the uppermost component being numbered one. The value of this object should never be greater than the value of s5ChasGrpMaxEnts. If not available, a value of zero will be returned. Note: This object is only implemented in agents that support 'virtual' chassis.
STR s5ChasComLocation	1.3.6.1.4.1.45.1.6.3.3.1.1.14	DisplayString	read-write	This object provides geographic location information of a component in a system modeled as a chassis, but possibly physically implemented with geographically separate devices connected together to exchange managment information. Chassis' modeled in this manner are sometimes refered to as 'virtual chassis'. An example value is: '4th flr wiring closet in blg A'. Notes: 1.) This object is applicable only to components that can be found in either the Board or Unit groups. If the information is unavailable (i.e., not modeling a virtual chassis or component is not in Board or Unit group), the value is a zero length string. 2.) If this object is applicable and is not assigned a value via a SNMP SET PDU when the row is created, the value will default to the value of the object s5ChasComSerNum.
I32 s5ChasComGroupMap	1.3.6.1.4.1.45.1.6.3.3.1.1.15	Integer32	read-only	This object describes the group mapping of each component in the chassis. For the components in the unit group, the value of this object should be the backplane number to which the unit is connected. The value of this object should never be greater than the value of s5ChasGrpMaxEnts. If not available, a value of zero should be returned.
I32 s5ChasComBaseNumPorts	1.3.6.1.4.1.45.1.6.3.3.1.1.16	Integer32	read-only	This object indicates the number of ports (of any type) contained in a component, not including any sub-components contained within the component.
I32 s5ChasComTotalNumPorts	1.3.6.1.4.1.45.1.6.3.3.1.1.17	Integer32	read-only	This object indicates the total number of ports (of any type) contained in a component, including any ports contained in sub-components contained within the component.
IP s5ChasComIpAddress	1.3.6.1.4.1.45.1.6.3.3.1.1.18	IpAddress	read-write	The IP address of a component. For components that do not have an IP address/stack, this value should always be 0.0.0.0. Note that for a stackable system in stack mode, this will be the standalone IP address for individual units in the stack.
STR s5ChasComRunningSoftwareVer	1.3.6.1.4.1.45.1.6.3.3.1.1.19	DisplayString	read-only	The version number of the software image running on this component/sub-component. If not available, the value is a zero length string.
ADR s5ChasComIpv6Address	1.3.6.1.4.1.45.1.6.3.3.1.1.20	Ipv6Address	read-write	The IPv6 address of a component. For components that do not have an IPv6 address/stack, this value should always be 0::0. Note that for a stackable system in stack mode, this will be the standalone IPv6 address for individual units in the stack.
ADR s5ChasComIpv6NetMask	1.3.6.1.4.1.45.1.6.3.3.1.1.21	Ipv6AddressPrefix	read-write	The IPv6 netmask of a component. For components that do not have an IPv6 address/stack, this value should always be 0::0. Note that for a stackable system in stack mode, this will be the standalone IPv6 netmask for individual units in the stack.
IP s5ChasComIpMgmtAddress	1.3.6.1.4.1.45.1.6.3.3.1.1.22	IpAddress	read-write	The IP address associated with the physical dedicated management port (out of band management port) of a component. For components that do not have an IP address/stack associated with the dedicated management port, this value should always be 0.0.0.0. Note that for a stackable system in stack mode, this IP address always applies to individual units in the stack.
IP s5ChasComIpMgmtNetMask	1.3.6.1.4.1.45.1.6.3.3.1.1.23	IpAddress	read-write	The IP netmask associated with the physical dedicated management port (out of band management port) of a component. For components that do not have an IP address/stack associated with the dedicated management port, this value should always be 0.0.0.0. Note that for a stackable system in stack mode, this netmask always applies to individual units in the stack.
IP s5ChasComIpMgmtGateway	1.3.6.1.4.1.45.1.6.3.3.1.1.24	IpAddress	read-write	The IP address of the default gateway associated with the physical dedicated management port (out of band management port) of a component. For components that do not have an IP address/stack associated with the dedicated management port, this value should always be 0.0.0.0. Note that for a stackable system in stack mode, this IP address always applies to individual units in the stack.
ADR s5ChasComIpv6MgmtAddress	1.3.6.1.4.1.45.1.6.3.3.1.1.25	Ipv6Address	read-write	The IPv6 address associated with the physical dedicated management port (out of band management port) of a component. Note that for a stackable system in stack mode, this IP address always applies to individual units in the stack.
ADR s5ChasComIpv6MgmtNetMask	1.3.6.1.4.1.45.1.6.3.3.1.1.26	Ipv6AddressPrefix	read-write	The IPv6 netmask associated with the physical dedicated management port (out of band management port) of a component. Note that for a stackable system in stack mode, this netmask always applies to individual units in the stack.
I32 s5ChasComIpMgmtLimit	1.3.6.1.4.1.45.1.6.3.3.1.1.27	Integer32	read-write	This object indicates the in-bound packet threshold rate for the management port (out of band management port).
I32 s5ChasComIpMgmtTimeout	1.3.6.1.4.1.45.1.6.3.3.1.1.28	Integer32	read-write	This object indicates the port shutdown period for the management port (out of band management port).
T/F s5ChasComIpMgmtShutdown	1.3.6.1.4.1.45.1.6.3.3.1.1.29	TruthValue	read-write	This object is used to control whether the out of band management port is up or down (false for port up and true for port down).
TIK s5ChasComUpTime	1.3.6.1.4.1.45.1.6.3.3.1.1.30	TimeTicks	read-only	The time (in hundredths of a second) since the unit was initialized.
s5ChasBrd	1.3.6.1.4.1.45.1.6.3.4
s5ChasBrdTable	1.3.6.1.4.1.45.1.6.3.4.1		not-accessible	A table containing information about each board that can be inserted into a slot. These include boards such as Repeater Modules and Network Management Modules.
s5ChasBrdEntry	1.3.6.1.4.1.45.1.6.3.4.1.1		not-accessible	A row in the board table. Entries can not be created or deleted via SNMP. Entries are created and deleted when boards are inserted or removed from slots in the chassis.
I32 s5ChasBrdIndx	1.3.6.1.4.1.45.1.6.3.4.1.1.1	Integer32	read-only	The index of the board. This corresponds to the index of the slot containing the board.
OCT s5ChasBrdLeds	1.3.6.1.4.1.45.1.6.3.4.1.1.2	OCTET STRING	read-only	A bit array that contains the value of the front panel LEDs and the annunciator. This is a packed bit string; each LED is encoded into 4 bits (a nibble). The first nibble is stored in the high order bits of the first octet. The second nibble is stored in the low order bits the first octet, etc. However, the current mapping is that the first three nibbles are reserved, the fourth nibble has the value of the 'annunciator', and the 'normal' LEDs start with the fifth nibble. If the LED values are not available, a zero length string is returned. The following shows the meaning of each bit (bit 0 is the least significant bit) when it has a value of one: bit meaning --- ------- 0 green light 1 yellow light 2 blinking 3 reserved
I32 s5ChasBrdNumAtt	1.3.6.1.4.1.45.1.6.3.4.1.1.3	Integer32	read-only	The total number of backplane network attachment points on the board. This may vary based on the mode of the board for FDDI.
C32 s5ChasBrdAttChngs	1.3.6.1.4.1.45.1.6.3.4.1.1.4	Counter32	read-only	The total number of attachment changes for the board that have been detected since cold/warm start of the agent or since the board was inserted.
TIK s5ChasBrdAttLstChng	1.3.6.1.4.1.45.1.6.3.4.1.1.5	TimeTicks	read-only	The value of sysUpTime when the last attachment change on the board has detected. If none have been detected since cold/warm start of the agent, then the value is zero.
STR s5ChasBrdStatusDsply	1.3.6.1.4.1.45.1.6.3.4.1.1.6	DisplayString	read-only	The current ASCII character display of the board. The length returned should match the length of the display. Boards with multiple displays should return the values concatenated together. Boards with no display hardware should return a zero length string.
STR s5ChasBrdDateCode	1.3.6.1.4.1.45.1.6.3.4.1.1.7	DisplayString	read-only	The date of manufacture of the board in ASCII in the format: YYYYmmdd. For example, the value for April 13, 1993 is 19930413. If not available, the value is a zero-length string.
INT s5ChasBrdCfgSrc	1.3.6.1.4.1.45.1.6.3.4.1.1.8	INTEGER	read-only	The source of the configuration at the last board reset. The values are: other(1)........unknown or some other value dfltJmpr(2).....default jumpers prmMem(3).......permanent memory on board brdCfg(4).......saved configuration on board sm(5)...........supervisor smDfltJmpr(6)...SM and default jumpers smPrmMem(7).....SM and permanent memory on board smBrdCfg(8).....SM and saved configuration on board
C32 s5ChasBrdCfgChngs	1.3.6.1.4.1.45.1.6.3.4.1.1.9	Counter32	read-only	The total number of configuration changes for the board that have been detected since cold/warm start of the agent or since the board was inserted.
OCT s5ChasBrdFanLeds	1.3.6.1.4.1.45.1.6.3.4.1.1.10	OCTET STRING	read-only	A bit array that contains the value of the front panel LEDs of the fan trays. This is a packed bit string; each LED is encoded into 4 bits (a nibble). The first nibble is stored in the high order bits of the first octet. The second nibble is stored in the low order bits of the first octet etc. The current mapping is that the first four nibbles are reserved, the fifth nibble has the value of the 'annunciator', and the 'normal' LEDs start with the sixth nibble. If the LED values are not available, a zero length string is returned. The following shows the meaning of each bit (bit 0 is the least significant bit) when it has a value of one: bit meaning --- ------- 0 red light 1 blue light 2 purple light 3 blinking 4 reserved
s5ChasAttTable	1.3.6.1.4.1.45.1.6.3.4.2		not-accessible	A table containing information about each backplane attachment point on a board. The number of entries for a board is the value of s5ChasBrdNumAtt.
s5ChasAttEntry	1.3.6.1.4.1.45.1.6.3.4.2.1		not-accessible	A row in the attachment point table. Entries can not be created or deleted via SNMP. Entries are created and deleted when boards are inserted or removed from slots in the chassis, or the number of attachment points is changed.
I32 s5ChasAttBrdIndx	1.3.6.1.4.1.45.1.6.3.4.2.1.1	Integer32	read-only	The index of the board. This corresponds to the index of the slot containing the board.
I32 s5ChasAttIndx	1.3.6.1.4.1.45.1.6.3.4.2.1.2	Integer32	read-only	The index of the attachment point on the board.
ATT s5ChasAttDfltAtt	1.3.6.1.4.1.45.1.6.3.4.2.1.3	AttId	read-only	The default setting for the attachment point. An attachment point may be attached to a local channel, not attached to any backplane network, or attached to a media specific backplane network. (The valid choices depend on each specific attachment point.) NOTE: This value will always be valid and may change when the backplane divider switch setting is changed.
ATT s5ChasAttCurAtt	1.3.6.1.4.1.45.1.6.3.4.2.1.4	AttId	read-write	The current setting for the attachment point. The slot position of the board, the setting of the backplane divider switch(es), and the mode setting affect which backplane networks are valid values. Also, some boards may put limitations on which backplane network(s) or local channel(s) may be used.
C32 s5ChasAttChngs	1.3.6.1.4.1.45.1.6.3.4.2.1.5	Counter32	read-only	The total number of attachment changes for the attachment point that have been detected since cold/warm start of the agent.
TIK s5ChasAttLstChng	1.3.6.1.4.1.45.1.6.3.4.2.1.6	TimeTicks	read-only	The value of sysUpTime when the last attachment change for the attachment point was detected. If none have been detected since cold/warm start of the agent, then the value is zero.
OCT s5ChasAttClusterConnCapability	1.3.6.1.4.1.45.1.6.3.4.2.1.7	OCTET STRING	read-only	A bit array that contains the bit map representing all available backplane segment and local segment connections for the cluster. One bit is also reserved to indicate if the cluster has an isolate capability. The first 31 bits of the array represent the backplane numbers, starting from the lower order bit. Bit 32 indicates whether the Cluster has a null connection capability. The bits in the fifth and sixth octets, starting with bits in the lower order octet, represent local segments that the cluster can connect to. A bit with a value of 1 means that the cluster is capable of connecting to the corresponding backplane segment, local segment or null segment.
s5ChasLocChanTable	1.3.6.1.4.1.45.1.6.3.4.3		not-accessible	A table containing information about each 'dual mode' local channel on a board.
s5ChasLocChanEntry	1.3.6.1.4.1.45.1.6.3.4.3.1		not-accessible	A row in the local channel table. Entries can not be created or deleted via SNMP. Entries are added or removed by adding or removing a board that has a 'dual mode' local channel from a slot in the chassis.
I32 s5ChasLocChanBrdIndx	1.3.6.1.4.1.45.1.6.3.4.3.1.1	Integer32	read-only	The index of the board. This corresponds to the index of the slot containing the board.
LOC s5ChasLocChanIndx	1.3.6.1.4.1.45.1.6.3.4.3.1.2	LocChan	read-only	The index of the local channel.
INT s5ChasLocChanBkplMode	1.3.6.1.4.1.45.1.6.3.4.3.1.3	INTEGER	read-write	Indicates the attachment/isolation mode of a local channel to a backplane channel. The values that are read/write are: connected(2)......connect local chan N to bkpl N notConnected(3)...disconnect local chan N from bkpl The possible values that can be read are: other(1)..........unknown connected(2)......local chan N connected to bkpl N notConnected(3)...local chan N isolated from bkpl N
s5ChasStore	1.3.6.1.4.1.45.1.6.3.5
s5ChasStoreTable	1.3.6.1.4.1.45.1.6.3.5.1		not-accessible	A table listing the storage areas on each component/sub-component in the chassis. The number is determined by the components in the chassis which have manageable storage areas. Examples of storage areas include RAM(main memory), FLASH, ROM, EEPROM, etc. This does not include disk drives.
s5ChasStoreEntry	1.3.6.1.4.1.45.1.6.3.5.1.1		not-accessible	A row in the table of storage areas. The entries can not be created or deleted via SNMP requests. Only those components/sub-components that have storage areas that are installed are present. Storage areas that are on components have a sub-component index value of zero. Storage areas that are on sub-components have a non-zero sub-component index value.
I32 s5ChasStoreGrpIndx	1.3.6.1.4.1.45.1.6.3.5.1.1.1	Integer32	read-only	The index of the chassis level group which contains the component or sub-component containing the storage area.
I32 s5ChasStoreComIndx	1.3.6.1.4.1.45.1.6.3.5.1.1.2	Integer32	read-only	The index of the component or the component which contains the sub-component containing the storage area.
I32 s5ChasStoreSubIndx	1.3.6.1.4.1.45.1.6.3.5.1.1.3	Integer32	read-only	If the storage area is on a component, then the value zero. Otherwise, the storage area is on a sub-component and this is the index of the sub-component.
I32 s5ChasStoreIndx	1.3.6.1.4.1.45.1.6.3.5.1.1.4	Integer32	read-only	The index of the storage area on the component or sub-component.
OID s5ChasStoreType	1.3.6.1.4.1.45.1.6.3.5.1.1.5	OBJECT IDENTIFIER	read-only	The storage area type on the containing component/sub-component. The values are defined under the .0 branch of the value of s5ChasComType for the component/sub-component containing the storage area in the Registration MIB.
I32 s5ChasStoreCurSize	1.3.6.1.4.1.45.1.6.3.5.1.1.6	Integer32	read-only	The current size of the storage area in bytes. A value of zero means the storage area is not installed or not usable. A value of -1 indicates that the size is unknown (or unavailable).
STR s5ChasStoreCntntVer	1.3.6.1.4.1.45.1.6.3.5.1.1.7	DisplayString	read-only	The version of the contents (i.e., the code or data) of the storage area in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a zero length string. If multiple contents are stored in this container, the the value will contain multiple sub-versions, each separated by a semicolon (;).
STR s5ChasStoreFilename	1.3.6.1.4.1.45.1.6.3.5.1.1.8	DisplayString	read-write	Name of the image file to be downloaded or uploaded when the s5AgInfoFileAction object is set to upload or download an image. When the object is not used, the value is a zero-length string.
I32 s5ChasStoreUsedSize	1.3.6.1.4.1.45.1.6.3.5.1.1.9	Integer32	read-only	The current size of the storage area that is currently in use, measured in bytes. A value of zero means the storage area is not in use. A value of -1 means the size is unknown (or unavailable).
STR s5ChasStoreDescription	1.3.6.1.4.1.45.1.6.3.5.1.1.10	DisplayString	read-only	A string describing the storage area. When the object is not used, the value is a zero-length string.
I32 s5ChasStoreAge	1.3.6.1.4.1.45.1.6.3.5.1.1.11	Integer32	read-only	A counter of the number of writes performed on this storage area which for areas residing in flash memory is an indication of the flash memory age. This number is the maximum number of writes for any of the access units (e.g. sector) from the storage area. A value of zero means the storage area is not in use. A value of -1 means the age is unknown (or unavailable).
s5ChasSm	1.3.6.1.4.1.45.1.6.3.6
OCT s5ChasSmLeds	1.3.6.1.4.1.45.1.6.3.6.1	OCTET STRING	read-only	A bit array that contains the value of the supervisor LEDs. (The format of these are the same as the format for object s5ChasBrdLeds.) If not available, a zero length string is returned.
STR s5ChasSmDateCode	1.3.6.1.4.1.45.1.6.3.6.2	DisplayString	read-only	The date of manufacture of the SM module in ASCII in the format: YYYYmmdd. For example, the value for April 13, 1993 is 19930413. If not available, a zero length string is returned
s5ChasTmpSnr	1.3.6.1.4.1.45.1.6.3.7
s5ChasTmpSnrTable	1.3.6.1.4.1.45.1.6.3.7.1		not-accessible	A table that contains temperature sensor values.
s5ChasTmpSnrEntry	1.3.6.1.4.1.45.1.6.3.7.1.1		not-accessible	A row in the s5ChasTmpSnrTable. Rows in this table will exist for each existing row in the s5ChasComTable which represents a temperature sensor. The values of the indices of the row in this table will be equal to those of the corresponding row in the s5ChasComTable.
I32 s5ChasTmpSnrGrpIndx	1.3.6.1.4.1.45.1.6.3.7.1.1.1	Integer32	read-only	The index of the chassis level group which contains this component, corresponds to s5ChasComGrpIndx.
I32 s5ChasTmpSnrIndx	1.3.6.1.4.1.45.1.6.3.7.1.1.2	Integer32	read-only	The index of the component in the group. Corresponds to s5ChasComIndx.
I32 s5ChasTmpSnrSubIndx	1.3.6.1.4.1.45.1.6.3.7.1.1.3	Integer32	read-only	Sub-component index. Corresponds to s5ChasComSubIndx.
G32 s5ChasTmpSnrValue	1.3.6.1.4.1.45.1.6.3.7.1.1.4	Gauge32	read-only	The current temperature value of the temperature sensor. This is measured in units of a half degree centigrade, e.g. a value of 121 indicates a temperature of 60.5 degrees C. This object is deprecated because it cannot represent temperature values below 0, as Gauge32 is an unsigned type.
I32 s5ChasTmpSnrTmpValue	1.3.6.1.4.1.45.1.6.3.7.1.1.5	Integer32	read-only	The current temperature value of the temperature sensor. This is measured in units of a half degree centigrade, e.g. a value of 121 indicates a temperature of 60.5 degrees C.
s5ChasUtil	1.3.6.1.4.1.45.1.6.3.8
s5ChasUtilTable	1.3.6.1.4.1.45.1.6.3.8.1		not-accessible	A table that contains CPU and memory utilization information.
s5ChasUtilEntry	1.3.6.1.4.1.45.1.6.3.8.1.1		not-accessible	A row in the s5ChasUtilTable. Rows in this table will exist for each existing row in the s5ChasComTable which represents any chassis component for which CPU and/or memory utilization values are available. The values of the indices of a row in this table will be equal to those of the corresponding row in the s5ChasComTable.
I32 s5ChasUtilGrpIndx	1.3.6.1.4.1.45.1.6.3.8.1.1.1	Integer32	read-only	The index of the chassis level group which contains this component, corresponds to s5ChasComGrpIndx.
I32 s5ChasUtilIndx	1.3.6.1.4.1.45.1.6.3.8.1.1.2	Integer32	read-only	The index of the component in the group. Corresponds to s5ChasComIndx.
I32 s5ChasUtilSubIndx	1.3.6.1.4.1.45.1.6.3.8.1.1.3	Integer32	read-only	Sub-component index. Corresponds to s5ChasComSubIndx.
G32 s5ChasUtilTotalCPUUsage	1.3.6.1.4.1.45.1.6.3.8.1.1.4	Gauge32	read-only	This object returns the percentage of time the CPU has been busy since system initialization.
G32 s5ChasUtilCPUUsageLast1Minute	1.3.6.1.4.1.45.1.6.3.8.1.1.5	Gauge32	read-only	This object returns the percentage of time the CPU has been busy over the last 1 minute.
G32 s5ChasUtilCPUUsageLast10Minutes	1.3.6.1.4.1.45.1.6.3.8.1.1.6	Gauge32	read-only	This object returns the percentage of time the CPU has been busy over the last 10 minutes.
G32 s5ChasUtilCPUUsageLast1Hour	1.3.6.1.4.1.45.1.6.3.8.1.1.7	Gauge32	read-only	This object returns the percentage of time the CPU has been busy over the last 1 hour.
G32 s5ChasUtilCPUUsageLast24Hours	1.3.6.1.4.1.45.1.6.3.8.1.1.8	Gauge32	read-only	This object returns the percentage of time the CPU has been busy over the last 24 hours.
G32 s5ChasUtilMemoryAvailable	1.3.6.1.4.1.45.1.6.3.8.1.1.9	Gauge32	read-only	This object returns the percentage of dynamic memory that is currently free. This is measured as a percentage of the memory the was available immediately after system initialization.
G32 s5ChasUtilMemoryMinAvailable	1.3.6.1.4.1.45.1.6.3.8.1.1.10	Gauge32	read-only	This object returns the lowest percentage of dynamic memory that has been free since system initialization. This is a 'low-water mark' for memory utilization, and is essentially the lowest value of s5ChasUtilMemoryUsage since system initialization.
G32 s5ChasUtilCPUUsageLast10Seconds	1.3.6.1.4.1.45.1.6.3.8.1.1.11	Gauge32	read-only	This object returns the percentage of time the CPU has been busy over the last 10 seconds.
G32 s5ChasUtilMemoryTotalMB	1.3.6.1.4.1.45.1.6.3.8.1.1.12	Gauge32	read-only	This object returns the total RAM of unit.
G32 s5ChasUtilMemoryAvailableMB	1.3.6.1.4.1.45.1.6.3.8.1.1.13	Gauge32	read-only	This object returns the available RAM of unit.
s5ChasPs	1.3.6.1.4.1.45.1.6.3.9
s5ChasPsRpsuTable	1.3.6.1.4.1.45.1.6.3.9.1		not-accessible	A table that contains extended information on RPSU power supply components.
s5ChasPsRpsuEntry	1.3.6.1.4.1.45.1.6.3.9.1.1		not-accessible	A row in the s5ChasPsRpsuTable. Rows in this table will exist for each existing row in the s5ChasComTable which represents any RPSU power supply. The values of the indices of a row in this table will be equal to those of the corresponding row in the s5ChasComTable.
I32 s5ChasPsRpsuGrpIndx	1.3.6.1.4.1.45.1.6.3.9.1.1.1	Integer32	read-only	The index of the chassis level group which contains this component, corresponds to s5ChasComGrpIndx.
I32 s5ChasPsRpsuIndx	1.3.6.1.4.1.45.1.6.3.9.1.1.2	Integer32	read-only	The index of the component in the group. Corresponds to s5ChasComIndx.
I32 s5ChasPsRpsuSubIndx	1.3.6.1.4.1.45.1.6.3.9.1.1.3	Integer32	read-only	Sub-component index. Corresponds to s5ChasComSubIndx.
INT s5ChasPsRpsuType	1.3.6.1.4.1.45.1.6.3.9.1.1.4	INTEGER	read-write	This object returns the specific type of RPSU. It can be set to indicate to the system the type of installed RPSU in cases where the RPSU type cannot be automatically detected.
INT s5ChasPsRpsuSourceConfig	1.3.6.1.4.1.45.1.6.3.9.1.1.5	INTEGER	read-write	This object is used to specify how a particular RPSU should be used by the system, as follows: ups(1) Indicates that the RPSU should be used only as an uninterruptible power source for devices attached to powered ethernet ports. rpsu(2) Indicates that the RPSU should be used only as a source of backup power for the device itself. powerSharing(3) Indicates that the RPSU should be used both as a source of backup power for the device, and as a UPS for devices attached to powered ethernet ports.
s5ChasMib	1.3.6.1.4.1.45.1.6.3.10			5000 Chassis MIB Copyright 1995-2012 Nortel Networks, Inc. All rights reserved. This Nortel Networks SNMP Management Information Base Specification (Specification) embodies Nortel Networks' confidential and proprietary intellectual property. Nortel Networks retains all title and ownership in the Specification, including any revisions. This Specification is supplied 'AS IS', and Nortel Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
s5ChasNotify	1.3.6.1.4.1.45.1.6.3.11
INT s5ChasNotifyFanDirection	1.3.6.1.4.1.45.1.6.3.11.1	INTEGER	accessible-for-notify	This object is used in the s5CtrFanDirectionError notification to indicate fan direction.
s5ChasPluggables	1.3.6.1.4.1.45.1.6.3.12
s5ChasGbicInfoTable	1.3.6.1.4.1.45.1.6.3.12.1		not-accessible	A table that contains information about pluggable ports.
s5ChasGbicInfoEntry	1.3.6.1.4.1.45.1.6.3.12.1.1		not-accessible	A row in the s5ChasGbicInfoTable.
NUM s5ChasGbicInfoIfIndex	1.3.6.1.4.1.45.1.6.3.12.1.1.1	InterfaceIndex	read-only	A unique value, greater than zero, for each interface.
STR s5ChasGbicInfoGbicType	1.3.6.1.4.1.45.1.6.3.12.1.1.2	DisplayString	read-only	The type of pluggable part.
I32 s5ChasGbicInfoWavelength	1.3.6.1.4.1.45.1.6.3.12.1.1.3	Integer32	read-only	The wavelength value measured in nanometers for the pluggable part.
STR s5ChasGbicInfoVendorName	1.3.6.1.4.1.45.1.6.3.12.1.1.4	DisplayString	read-only	The name of the vendor of the pluggable part.
OCT s5ChasGbicInfoVendorOui	1.3.6.1.4.1.45.1.6.3.12.1.1.5	OCTET STRING	read-only	The Organizationally Unique Identifier (OUI) of the pluggable part.
STR s5ChasGbicInfoVendorPartNo	1.3.6.1.4.1.45.1.6.3.12.1.1.6	DisplayString	read-only	The vendor part number of the pluggable part.
STR s5ChasGbicInfoVendorRevision	1.3.6.1.4.1.45.1.6.3.12.1.1.7	DisplayString	read-only	The vendor revision of the pluggable part.
STR s5ChasGbicInfoVendorSerial	1.3.6.1.4.1.45.1.6.3.12.1.1.8	DisplayString	read-only	The vendor serial number for the pluggable part.
BIT s5ChasGbicInfoHwOptions	1.3.6.1.4.1.45.1.6.3.12.1.1.9	Bits	read-only	The hardware options supported by the pluggable part.
STR s5ChasGbicInfoDateCode	1.3.6.1.4.1.45.1.6.3.12.1.1.10	DisplayString	read-only	The manufacturing date of the pluggable part.
STR s5ChasGbicInfoCleiCode	1.3.6.1.4.1.45.1.6.3.12.1.1.11	DisplayString	read-only	The Common Language Equipment Identification Code of the pluggable part.
STR s5ChasGbicInfoProductCode	1.3.6.1.4.1.45.1.6.3.12.1.1.12	DisplayString	read-only	The product code of the pluggable part.

RFC description

Avaya S5000 chassis MIB managing physical components, power supplies, fans, module information, and system-level metrics on modular switches.

Start monitoring Avaya/Nortel BayStack S5000 series chassis switches (chassis identity/hardware-change counters) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download S5-CHASSIS-MIB