RUCKUS-PRODUCTS-MIB

All MIBs › RUCKUS-PRODUCTS-MIB

Organization: Ruckus Wireless, Inc.

Last Updated: 2010-10-15

Category: Wireless and Radio

Description: Registers product identity OIDs for the Ruckus Wireless access point and controller product family.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RUCKUS-PRODUCTS-MIB?

RUCKUS-PRODUCTS-MIB is a Ruckus Wireless MIB that both registers product-identity OIDs for the Ruckus AP/controller/router product family and, for at least some product lines shown in this excerpt (the ZoneFlex 7761 cable-modem/gateway line and the ZoneDirector 1000 WLAN controller), also carries actual configuration and status objects rather than pure identity placeholders. Visible objects cover remote management service enablement (HTTP, Telnet, SSH), device credentials, LED control mode, heartbeat-monitor settings for both the cable modem and its managed AP, and ZoneDirector system name/IP address. Its monitoring relevance spans both software configuration status (which management services are enabled, LED indication mode) and basic reachability health (heartbeat monitor state between the CM and AP), rather than deep environmental sensors — this is closer to device-management and reachability status than to temperature/power monitoring. It has no explicit stated dependency on other MIBs in this excerpt, functioning as Ruckus's own top-level enterprise product tree. It is deployed on Ruckus wireless routers, access points, and ZoneDirector WLAN controllers in enterprise and service-provider Wi-Fi deployments, where the RUCKUS-PRODUCTS-MIB MIB provides the product-identity and configuration objects administrators poll.

IPNetwork Monitor allows you to monitor SNMP objects defined in RUCKUS-PRODUCTS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ruckus wireless router/gateway (ZoneFlex)
Ruckus ZoneDirector WLAN controller
Ruckus access point

Monitoring Examples

An operator managing a ZoneFlex 7761 cable-modem/gateway would check ruckusZF7761CMHTTPService, ruckusZF7761CMTelnetService, and ruckusZF7761CMSSHService to confirm which remote management protocols are enabled, and ruckusZF7761CMHeartbeatMonitorCM/ruckusZF7761CMHeartbeatMonitorAP to verify the cable modem and its associated access point are still reporting in to each other. For a ZoneDirector 1000 controller, ruckusZD1000SystemName and ruckusZD1000SystemIPAddr would be polled to confirm the controller's identity and management address are as expected. ruckusZF7761CMControlLED/ruckusZF7761CMLEDMode would be relevant when diagnosing a device whose LED indication doesn't match its actual operational state.

What Can Be Monitored

remote management service enablement (HTTP/Telnet/SSH)
heartbeat monitor status between CM and AP
LED control mode/state
system name and IP address (ZoneDirector)

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From RUCKUS-ROOT-MIB

ruckusProducts

OBJECT-IDENTITY

From RUCKUS-TC-MIB

RuckusCountryCode

From SNMPv2-SMI

MODULE-IDENTITY

From SNMPv2-TC

DisplayString
MacAddress
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
ruckusProductsMIB	1.3.6.1.4.1.25053.3.1			Ruckus product OID registration mib.
ruckusWirelessRouterProducts	1.3.6.1.4.1.25053.3.1.1
ruckusVF2825	1.3.6.1.4.1.25053.3.1.1.1
ruckusVF2811	1.3.6.1.4.1.25053.3.1.1.2
ruckusVF2821	1.3.6.1.4.1.25053.3.1.1.3
ruckusVF2835	1.3.6.1.4.1.25053.3.1.1.4
ruckusVF7811	1.3.6.1.4.1.25053.3.1.1.5
ruckusWirelessAdapterProducts	1.3.6.1.4.1.25053.3.1.2
ruckusVF2111	1.3.6.1.4.1.25053.3.1.2.1
ruckusVF2121	1.3.6.1.4.1.25053.3.1.2.2
ruckusVF7111	1.3.6.1.4.1.25053.3.1.2.3
ruckusWirelessMetroProducts	1.3.6.1.4.1.25053.3.1.3
ruckusMM2225	1.3.6.1.4.1.25053.3.1.3.1
ruckusMM2211	1.3.6.1.4.1.25053.3.1.3.2
ruckusMM2221	1.3.6.1.4.1.25053.3.1.3.3
ruckusWirelessHotzoneProducts	1.3.6.1.4.1.25053.3.1.4
ruckusZF2925	1.3.6.1.4.1.25053.3.1.4.1
ruckusZF2942	1.3.6.1.4.1.25053.3.1.4.2
ruckusZF7942	1.3.6.1.4.1.25053.3.1.4.3
ruckusZF7962	1.3.6.1.4.1.25053.3.1.4.4
ruckusZF2741	1.3.6.1.4.1.25053.3.1.4.5
ruckusZF7762	1.3.6.1.4.1.25053.3.1.4.6
ruckusZF7761CM	1.3.6.1.4.1.25053.3.1.4.7
INT ruckusZF7761CMControlLED	1.3.6.1.4.1.25053.3.1.4.7.3	INTEGER	read-write	ledPerCM(1): LEDs enabled per Cable Modem definition, ledPerAP(2): LEDs configured per Access Point definition, ledAlternateMode1Mode2OneHour(3): Alternalte between modes 1 and 2 at a 30 second period then disabled after one hour, ledAlternateMode1Mode2Mode6(4): Alternalte between modes 1 and 2 at a 30 second period and then go to mode 6 blueActive(5): Blue Active Surge Protection Indicator, blueActiveCMOnlineLed(6): Blue Active Surge Protection Indicator and Cable Modem online Green LED enabled, ledAllOff(7): All LEDs disabled, heartbeatOffCM(8): Disable Cable Modem heartbeat monitoring, heartbeatOffAP(9): Disable Access Point heartbeat monitoring, softResetAP(10): Soft reset of Access Point, powerCycleAP(11): Power cycle Access Point, factoryResetAP(12): Reset Access Point to factory defaults, softResetCM(13): Soft reset of Cable Modem, powerCycleCM(14): Power cycle Cable Modem, factoryResetCM(15): Reset Cable Modem to factory defaults
IP ruckusZF7761CMWanIPAddr	1.3.6.1.4.1.25053.3.1.4.7.4	IpAddress	read-only	Specifies the IP address of the Cable Modem WAN interface.
ruckusZF7761CMCustomization	1.3.6.1.4.1.25053.3.1.4.7.5
T/F ruckusZF7761CMHTTPService	1.3.6.1.4.1.25053.3.1.4.7.5.1	TruthValue	read-write	Enable/disable HTTP service.
T/F ruckusZF7761CMTelnetService	1.3.6.1.4.1.25053.3.1.4.7.5.2	TruthValue	read-write	Enable/disable Telnet service.
T/F ruckusZF7761CMSSHService	1.3.6.1.4.1.25053.3.1.4.7.5.3	TruthValue	read-write	Enable/disable SSH service.
STR ruckusZF7761CMUsername	1.3.6.1.4.1.25053.3.1.4.7.5.4	DisplayString	read-write	Specifies username of cable modem.
STR ruckusZF7761CMPassword	1.3.6.1.4.1.25053.3.1.4.7.5.5	DisplayString	read-write	Specifies password of cable modem.
INT ruckusZF7761CMLEDMode	1.3.6.1.4.1.25053.3.1.4.7.6	INTEGER	read-write	ledAllOff(0): All LEDs disabled after 3 second delay, blueActive(1): Blue Active Surge Protection Indicator, blueActiveCMOnlineLed(2): Blue Active Surge Protection Indicator and Cable Modem online Green LED enabled
T/F ruckusZF7761CMHeartbeatMonitorCM	1.3.6.1.4.1.25053.3.1.4.7.7	TruthValue	read-write	Enable/disable Cable Modem heartbeat monitoring.
T/F ruckusZF7761CMHeartbeatMonitorAP	1.3.6.1.4.1.25053.3.1.4.7.8	TruthValue	read-write	Enable/disable Access Point heartbeat monitoring.
ruckusZF7762S	1.3.6.1.4.1.25053.3.1.4.8
ruckusZF7762T	1.3.6.1.4.1.25053.3.1.4.9
ruckusZF7762N	1.3.6.1.4.1.25053.3.1.4.10
ruckusZF7343	1.3.6.1.4.1.25053.3.1.4.12
ruckusZF7363	1.3.6.1.4.1.25053.3.1.4.13
ruckusZF7341	1.3.6.1.4.1.25053.3.1.4.14
ruckusZF7731	1.3.6.1.4.1.25053.3.1.4.16
ruckusZF7025	1.3.6.1.4.1.25053.3.1.4.20
ruckusZF7321	1.3.6.1.4.1.25053.3.1.4.22
ruckusZF7321U	1.3.6.1.4.1.25053.3.1.4.23
ruckusZF2741EXT	1.3.6.1.4.1.25053.3.1.4.24
ruckusZF7982	1.3.6.1.4.1.25053.3.1.4.25
ruckusZF7782	1.3.6.1.4.1.25053.3.1.4.28
ruckusZF7782S	1.3.6.1.4.1.25053.3.1.4.29
ruckusZF7782N	1.3.6.1.4.1.25053.3.1.4.30
ruckusZF7782E	1.3.6.1.4.1.25053.3.1.4.31
ruckusZF8800SAC	1.3.6.1.4.1.25053.3.1.4.32
ruckusZF7762AC	1.3.6.1.4.1.25053.3.1.4.35
ruckusZF7762SAC	1.3.6.1.4.1.25053.3.1.4.36
ruckusZF7762TAC	1.3.6.1.4.1.25053.3.1.4.37
ruckusZF7372	1.3.6.1.4.1.25053.3.1.4.40
ruckusZF7372E	1.3.6.1.4.1.25053.3.1.4.41
ruckusZF7352	1.3.6.1.4.1.25053.3.1.4.45
ruckusZF7351	1.3.6.1.4.1.25053.3.1.4.48
ruckusZF7742	1.3.6.1.4.1.25053.3.1.4.50
ruckusZF7055	1.3.6.1.4.1.25053.3.1.4.52
ruckusZF7781M	1.3.6.1.4.1.25053.3.1.4.55
ruckusZF7781CM	1.3.6.1.4.1.25053.3.1.4.56
ruckusZF7781CME	1.3.6.1.4.1.25053.3.1.4.57
ruckusZF7781CMS	1.3.6.1.4.1.25053.3.1.4.58
ruckusZF7781FN	1.3.6.1.4.1.25053.3.1.4.60
ruckusZF7781FNE	1.3.6.1.4.1.25053.3.1.4.61
ruckusZF7781FNS	1.3.6.1.4.1.25053.3.1.4.62
ruckusSC8800SAC	1.3.6.1.4.1.25053.3.1.4.65
ruckusSC8800S	1.3.6.1.4.1.25053.3.1.4.66
ruckusWirelessControllerProducts	1.3.6.1.4.1.25053.3.1.5
ruckusZD1000	1.3.6.1.4.1.25053.3.1.5.1
STR ruckusZD1000SystemName	1.3.6.1.4.1.25053.3.1.5.1.1	DisplayString	read-only	System name
IP ruckusZD1000SystemIPAddr	1.3.6.1.4.1.25053.3.1.5.1.2	IpAddress	read-only	IP Address
MAC ruckusZD1000SystemMacAddr	1.3.6.1.4.1.25053.3.1.5.1.3	MacAddress	read-only	MAC Address
TIK ruckusZD1000SystemUptime	1.3.6.1.4.1.25053.3.1.5.1.4	TimeTicks	read-only	Up time
STR ruckusZD1000SystemModel	1.3.6.1.4.1.25053.3.1.5.1.5	DisplayString	read-only	Model
U32 ruckusZD1000SystemLicensedAPs	1.3.6.1.4.1.25053.3.1.5.1.6	Unsigned32	read-only	Licensed APs
STR ruckusZD1000SystemSerialNumber	1.3.6.1.4.1.25053.3.1.5.1.7	DisplayString	read-only	Serial number
STR ruckusZD1000SystemVersion	1.3.6.1.4.1.25053.3.1.5.1.8	DisplayString	read-only	Software version
RUC ruckusZD1000CountryCode	1.3.6.1.4.1.25053.3.1.5.1.9	RuckusCountryCode	read-only	Country code
ruckusZD1100	1.3.6.1.4.1.25053.3.1.5.2
STR ruckusZD1100SystemName	1.3.6.1.4.1.25053.3.1.5.2.1	DisplayString	read-only	System name
IP ruckusZD1100SystemIPAddr	1.3.6.1.4.1.25053.3.1.5.2.2	IpAddress	read-only	IP Address
MAC ruckusZD1100SystemMacAddr	1.3.6.1.4.1.25053.3.1.5.2.3	MacAddress	read-only	MAC Address
TIK ruckusZD1100SystemUptime	1.3.6.1.4.1.25053.3.1.5.2.4	TimeTicks	read-only	Up time
STR ruckusZD1100SystemModel	1.3.6.1.4.1.25053.3.1.5.2.5	DisplayString	read-only	Model
U32 ruckusZD1100SystemLicensedAPs	1.3.6.1.4.1.25053.3.1.5.2.6	Unsigned32	read-only	Licensed APs
STR ruckusZD1100SystemSerialNumber	1.3.6.1.4.1.25053.3.1.5.2.7	DisplayString	read-only	Serial number
STR ruckusZD1100SystemVersion	1.3.6.1.4.1.25053.3.1.5.2.8	DisplayString	read-only	Software version
RUC ruckusZD1100CountryCode	1.3.6.1.4.1.25053.3.1.5.2.9	RuckusCountryCode	read-only	Country code
ruckusZD3000	1.3.6.1.4.1.25053.3.1.5.3
STR ruckusZD3000SystemName	1.3.6.1.4.1.25053.3.1.5.3.1	DisplayString	read-only	System name
IP ruckusZD3000SystemIPAddr	1.3.6.1.4.1.25053.3.1.5.3.2	IpAddress	read-only	IP Address
MAC ruckusZD3000SystemMacAddr	1.3.6.1.4.1.25053.3.1.5.3.3	MacAddress	read-only	MAC Address
TIK ruckusZD3000SystemUptime	1.3.6.1.4.1.25053.3.1.5.3.4	TimeTicks	read-only	Up time
STR ruckusZD3000SystemModel	1.3.6.1.4.1.25053.3.1.5.3.5	DisplayString	read-only	Model
U32 ruckusZD3000SystemLicensedAPs	1.3.6.1.4.1.25053.3.1.5.3.6	Unsigned32	read-only	Licensed APs
STR ruckusZD3000SystemSerialNumber	1.3.6.1.4.1.25053.3.1.5.3.7	DisplayString	read-only	Serial number
STR ruckusZD3000SystemVersion	1.3.6.1.4.1.25053.3.1.5.3.8	DisplayString	read-only	Software version
RUC ruckusZD3000CountryCode	1.3.6.1.4.1.25053.3.1.5.3.9	RuckusCountryCode	read-only	Country code
ruckusZD5000	1.3.6.1.4.1.25053.3.1.5.8
STR ruckusZD5000SystemName	1.3.6.1.4.1.25053.3.1.5.8.1	DisplayString	read-only	System name
IP ruckusZD5000SystemIPAddr	1.3.6.1.4.1.25053.3.1.5.8.2	IpAddress	read-only	IP Address
MAC ruckusZD5000SystemMacAddr	1.3.6.1.4.1.25053.3.1.5.8.3	MacAddress	read-only	MAC Address
TIK ruckusZD5000SystemUptime	1.3.6.1.4.1.25053.3.1.5.8.4	TimeTicks	read-only	Up time
STR ruckusZD5000SystemModel	1.3.6.1.4.1.25053.3.1.5.8.5	DisplayString	read-only	Model
U32 ruckusZD5000SystemLicensedAPs	1.3.6.1.4.1.25053.3.1.5.8.6	Unsigned32	read-only	Licensed APs
STR ruckusZD5000SystemSerialNumber	1.3.6.1.4.1.25053.3.1.5.8.7	DisplayString	read-only	Serial number
STR ruckusZD5000SystemVersion	1.3.6.1.4.1.25053.3.1.5.8.8	DisplayString	read-only	Software version
RUC ruckusZD5000CountryCode	1.3.6.1.4.1.25053.3.1.5.8.9	RuckusCountryCode	read-only	Country code

RFC description

Ruckus product OID registration for wireless routers, adapters, and controller devices.

Start monitoring Ruckus wireless router/gateway (ZoneFlex), Ruckus ZoneDirector WLAN controller, access point (product identity/config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RUCKUS-PRODUCTS-MIB

What Is RUCKUS-PRODUCTS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description