All MIBs › RFC1271-MIB
Category: Network Monitoring (RMON), SNMP Framework
Description: Provides the original Remote Network Monitoring (RMON) MIB, covering remote monitoring of LAN traffic statistics, packet capture, alarms, host tables, and event handling.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is RFC1271-MIB?
RFC1271-MIB is the original vendor-neutral IETF Remote Network Monitoring (RMON) MIB, the first standard for remote LAN traffic monitoring, later superseded by RFC 1757/2819. It defines groups for Ethernet statistics collection, history sampling, alarm thresholds, host and host-conversation tables, filters, packet capture, and event/log generation, giving a probe or switch the ability to summarize traffic patterns without constant polling from a management station. Its monitoring focus is squarely on network traffic and performance behavior rather than physical hardware sensors: utilization percentages, error/collision counts, top-talker host statistics, and threshold-crossing alarms that trigger logged events are all exposed here. RFC1271-MIB was effectively superseded by later RMON revisions (RFC 1757, and RMON2 in RFC 2021), and because it is now mainly of historical interest, an RFC1271-MIB reference today is usually consulted to understand the original RMON group structure that its successors carried forward largely unchanged. It was historically deployed in RMON-capable probes and switches used for proactive LAN traffic monitoring and threshold-based alerting on Ethernet segments.
IPNetwork Monitor allows you to monitor SNMP objects defined in RFC1271-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer
- RMON-capable network probes and switches monitoring Ethernet segments
Monitoring Examples
No sample objects were included for this module, but based on its well-known RMON structure, a typical scenario involves polling the Ethernet statistics group for collision and CRC error counts on a monitored segment, and the history group for utilization trends over time. The alarm group can be configured to watch a specific counter (e.g. errors per interval) and fire an event when it crosses a threshold, which the event group then logs or converts into an SNMP trap. The host table would separately reveal which MAC addresses are generating the most traffic on the segment.
What Can Be Monitored
- Ethernet segment utilization
- collision and CRC error counts
- traffic history trends
- top-talker host statistics
- threshold-crossing alarms
- logged RMON events
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| mib-2 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| alarm | 1.3.6.1.2.1.16.3 | |||
| alarmEntry | 1.3.6.1.2.1.16.3.1.1 | not-accessible | A list of parameters that set up a periodic checking for alarm conditions. | |
| INT alarmFallingEventIndex | 1.3.6.1.2.1.16.3.1.1.10 | INTEGER | read-write | The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT alarmFallingThreshold | 1.3.6.1.2.1.16.3.1.1.8 | INTEGER | read-write | A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT alarmIndex | 1.3.6.1.2.1.16.3.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device. |
| INT alarmInterval | 1.3.6.1.2.1.16.3.1.1.2 | INTEGER | read-write | The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be given to ensure that the variable being monitored will not exceed 2^31 - 1 and roll over the alarmValue object during the interval. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| STR alarmOwner | 1.3.6.1.2.1.16.3.1.1.11 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| INT alarmRisingEventIndex | 1.3.6.1.2.1.16.3.1.1.9 | INTEGER | read-write | The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT alarmRisingThreshold | 1.3.6.1.2.1.16.3.1.1.7 | INTEGER | read-write | A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT alarmSampleType | 1.3.6.1.2.1.16.3.1.1.4 | INTEGER | read-write | The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT alarmStartupAlarm | 1.3.6.1.2.1.16.3.1.1.6 | INTEGER | read-write | The alarm that may be sent when this entry is first set to valid. If the first sample after this entry becomes valid is greater than or equal to the risingThreshold and alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3), then a single rising alarm will be generated. If the first sample after this entry becomes valid is less than or equal to the fallingThreshold and alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3), then a single falling alarm will be generated. This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| ENT alarmStatus | 1.3.6.1.2.1.16.3.1.1.12 | EntryStatus | read-write | The status of this alarm entry. |
| alarmTable | 1.3.6.1.2.1.16.3.1 | not-accessible | A list of alarm entries. | |
| INT alarmValue | 1.3.6.1.2.1.16.3.1.1.5 | INTEGER | read-only | The value of the statistic during the last sampling period. The value during the current sampling period is not made available until the period is completed. |
| OID alarmVariable | 1.3.6.1.2.1.16.3.1.1.3 | OBJECT IDENTIFIER | read-write | The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Counter, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1). |
| INT bufferControlCapturedPackets | 1.3.6.1.2.1.16.8.1.1.10 | INTEGER | read-only | The number of packets currently in this captureBuffer. |
| INT bufferControlCaptureSliceSize | 1.3.6.1.2.1.16.8.1.1.5 | INTEGER | read-write | The maximum number of octets of each packet that will be saved in this capture buffer. For example, if a 1500 octet packet is received by the probe and this object is set to 500, then only 500 octets of the packet will be stored in the associated capture buffer. If this variable is set to 0, the capture buffer will save as many octets as is possible. This object may not be modified if the associated bufferControlStatus object is equal to valid(1). |
| INT bufferControlChannelIndex | 1.3.6.1.2.1.16.8.1.1.2 | INTEGER | read-write | An index that identifies the channel that is the source of packets for this bufferControl table. The channel identified by a particular value of this index is the same as identified by the same value of the channelIndex object. This object may not be modified if the associated bufferControlStatus object is equal to valid(1). |
| INT bufferControlDownloadOffset | 1.3.6.1.2.1.16.8.1.1.7 | INTEGER | read-write | The offset of the first octet of each packet in this capture buffer that will be returned in an SNMP retrieval of that packet. For example, if 500 octets of a packet have been stored in the associated capture buffer and this object is set to 100, then the captureBufferPacket object that contains the packet will contain bytes starting 100 octets into the packet. |
| INT bufferControlDownloadSliceSize | 1.3.6.1.2.1.16.8.1.1.6 | INTEGER | read-write | The maximum number of octets of each packet in this capture buffer that will be returned in an SNMP retrieval of that packet. For example, if 500 octets of a packet have been stored in the associated capture buffer, the associated bufferControlDownloadOffset is 0, and this object is set to 100, then the captureBufferPacket object that contains the packet will contain only the first 100 octets of the packet. A prudent manager will take into account possible interoperability or fragmentation problems that may occur if the download slice size is set too large. In particular, conformant SNMP implementations are not required to accept messages whose length exceeds 484 octets, although they are encouraged to support larger datagrams whenever feasible. |
| bufferControlEntry | 1.3.6.1.2.1.16.8.1.1 | not-accessible | A set of parameters that control the collection of a stream of packets that have matched filters. | |
| INT bufferControlFullAction | 1.3.6.1.2.1.16.8.1.1.4 | INTEGER | read-write | Controls the action of the buffer when it reaches the full status. When in the lockWhenFull(1) state a packet is added to the buffer that fills the buffer, the bufferControlFullStatus will be set to full(2) and this buffer will stop capturing packets. |
| INT bufferControlFullStatus | 1.3.6.1.2.1.16.8.1.1.3 | INTEGER | read-only | This object shows whether the buffer has room to accept new packets or if it is full. If the status is spaceAvailable(1), the buffer is accepting new packets normally. If the status is full(2) and the associated bufferControlFullAction object is wrapWhenFull, the buffer is accepting new packets by deleting enough of the oldest packets to make room for new ones as they arrive. Otherwise, if the status is full(2) and the bufferControlFullAction object is lockWhenFull, then the buffer has stopped collecting packets. When this object is set to full(2) the probe must not later set it to spaceAvailable(1) except in the case of a significant gain in resources such as an increase of bufferControlOctetsGranted. In particular, the wrap-mode action of deleting old packets to make room for newly arrived packets must not affect the value of this object. |
| INT bufferControlIndex | 1.3.6.1.2.1.16.8.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the bufferControl table. The value of this index shall never be zero. Each such entry defines one set of packets that is captured and controlled by one or more filters. |
| INT bufferControlMaxOctetsGranted | 1.3.6.1.2.1.16.8.1.1.9 | INTEGER | read-only | The maximum number of octets that can be saved in this captureBuffer, including overhead. If this variable is -1, the capture buffer will save as many octets as possible. When the bufferControlMaxOctetsRequested object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular probe implementation and available resources. However, if the request object has the special value of -1, the probe must set this object to -1. The probe must not lower this value except as a result of a modification to the associated bufferControlMaxOctetsRequested object. When this maximum number of octets is reached and a new packet is to be added to this capture buffer and the corresponding bufferControlFullAction is set to wrapWhenFull(2), enough of the oldest packets associated with this capture buffer shall be deleted by the agent so that the new packet can be added. If the corresponding bufferControlFullAction is set to lockWhenFull(1), the new packet shall be discarded. In either case, the probe must set bufferControlFullStatus to full(2). When the value of this object changes to a value less than the current value, entries are deleted from the captureBufferTable associated with this bufferControlEntry. Enough of the oldest of these captureBufferEntries shall be deleted by the agent so that the number of octets used remains less than or equal to the new value of this object. When the value of this object changes to a value greater than the current value, the number of associated captureBufferEntries may be allowed to grow. |
| INT bufferControlMaxOctetsRequested | 1.3.6.1.2.1.16.8.1.1.8 | INTEGER | read-write | The requested maximum number of octets to be saved in this captureBuffer, including any implementation-specific overhead. If this variable is set to -1, the capture buffer will save as many octets as is possible. When this object is created or modified, the probe should set bufferControlMaxOctetsGranted as closely to this object as is possible for the particular probe implementation and available resources. However, if the object has the special value of -1, the probe must set bufferControlMaxOctetsGranted to -1. |
| STR bufferControlOwner | 1.3.6.1.2.1.16.8.1.1.12 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| ENT bufferControlStatus | 1.3.6.1.2.1.16.8.1.1.13 | EntryStatus | read-write | The status of this buffer Control Entry. |
| bufferControlTable | 1.3.6.1.2.1.16.8.1 | not-accessible | A list of buffers control entries. | |
| TIK bufferControlTurnOnTime | 1.3.6.1.2.1.16.8.1.1.11 | TimeTicks | read-only | The value of sysUpTime when this capture buffer was first turned on. |
| capture | 1.3.6.1.2.1.16.8 | |||
| INT captureBufferControlIndex | 1.3.6.1.2.1.16.8.2.1.1 | INTEGER | read-only | The index of the bufferControlEntry with which this packet is associated. |
| captureBufferEntry | 1.3.6.1.2.1.16.8.2.1 | not-accessible | A packet captured off of an attached network. | |
| INT captureBufferIndex | 1.3.6.1.2.1.16.8.2.1.2 | INTEGER | read-only | An index that uniquely identifies an entry in the captureBuffer table associated with a particular bufferControlEntry. This index will start at 1 and increase by one for each new packet added with the same captureBufferControlIndex. |
| OCT captureBufferPacketData | 1.3.6.1.2.1.16.8.2.1.4 | OCTET STRING | read-only | The data inside the packet, starting at the beginning of the packet plus any offset specified in the associated bufferControlDownloadOffset, including any link level headers. The length of the data in this object is the minimum of the length of the captured packet minus the offset, the length of the associated bufferControlCaptureSliceSize minus the offset, and the associated bufferControlDownloadSliceSize. If this minimum is less than zero, this object shall have a length of zero. |
| INT captureBufferPacketID | 1.3.6.1.2.1.16.8.2.1.3 | INTEGER | read-only | An index that describes the order of packets that are received on a particular interface. The packetID of a packet captured on an interface is defined to be greater than the packetID's of all packets captured previously on the same interface. As the captureBufferPacketID object has a maximum positive value of 2^31 - 1, any captureBufferPacketID object shall have the value of the associated packet's packetID mod 2^31. |
| INT captureBufferPacketLength | 1.3.6.1.2.1.16.8.2.1.5 | INTEGER | read-only | The actual length (off the wire) of the packet stored in this entry, including FCS octets. |
| INT captureBufferPacketStatus | 1.3.6.1.2.1.16.8.2.1.7 | INTEGER | read-only | A value which indicates the error status of this packet. The value of this object is defined in the same way as filterPacketStatus. The value is a sum. This sum initially takes the value zero. Then, for each error, E, that has been discovered in this packet, 2 raised to a value representing E is added to the sum. The errors defined for a packet captured off of an Ethernet interface are as follows: bit # Error 0 Packet is longer than 1518 octets 1 Packet is shorter than 64 octets 2 Packet experienced a CRC or Alignment error 3 First packet in this capture buffer after it was detected that some packets were not processed correctly. For example, an Ethernet fragment would have a value of 6 (2^1 + 2^2). As this MIB is expanded to new media types, this object will have other media-specific errors defined. |
| INT captureBufferPacketTime | 1.3.6.1.2.1.16.8.2.1.6 | INTEGER | read-only | The number of milliseconds that had passed since this capture buffer was first turned on when this packet was captured. |
| captureBufferTable | 1.3.6.1.2.1.16.8.2 | not-accessible | A list of packets captured off of a channel. | |
| INT channelAcceptType | 1.3.6.1.2.1.16.7.2.1.3 | INTEGER | read-write | This object controls the action of the filters associated with this channel. If this object is equal to acceptMatched(1), packets will be accepted to this channel if they are accepted by both the packet data and packet status matches of an associated filter. If this object is equal to acceptFailed(2), packets will be accepted to this channel only if they fail either the packet data match or the packet status match of each of the associated filters. This object may not be modified if the associated channelStatus object is equal to valid(1). |
| INT channelDataControl | 1.3.6.1.2.1.16.7.2.1.4 | INTEGER | read-write | This object controls the flow of data through this channel. If this object is on(1), data, status and events flow through this channel. If this object is off(2), data, status and events will not flow through this channel. |
| STR channelDescription | 1.3.6.1.2.1.16.7.2.1.10 | DisplayString | read-write | A comment describing this channel. |
| channelEntry | 1.3.6.1.2.1.16.7.2.1 | not-accessible | A set of parameters for a packet channel applied on a particular interface. | |
| INT channelEventIndex | 1.3.6.1.2.1.16.7.2.1.7 | INTEGER | read-write | The value of this object identifies the event that is configured to be generated when the associated channelDataControl is on and a packet is matched. The event identified by a particular value of this object is the same event as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In fact, if no event is intended for this channel, channelEventIndex must be set to zero, a non-existent event index. This object may not be modified if the associated channelStatus object is equal to valid(1). |
| INT channelEventStatus | 1.3.6.1.2.1.16.7.2.1.8 | INTEGER | read-write | The event status of this channel. If this channel is configured to generate events when packets are matched, a means of controlling the flow of those events is often needed. When this object is equal to eventReady(1), a single event may be generated, after which this object will be set by the probe to eventFired(2). While in the eventFired(2) state, no events will be generated until the object is modified to eventReady(1) (or eventAlwaysReady(3)). The management station can thus easily respond to a notification of an event by re-enabling this object. If the management station wishes to disable this flow control and allow events to be generated at will, this object may be set to eventAlwaysReady(3). Disabling the flow control is discouraged as it can result in high network traffic or other performance problems. |
| INT channelIfIndex | 1.3.6.1.2.1.16.7.2.1.2 | INTEGER | read-write | The value of this object uniquely identifies the interface on this remote network monitoring device to which the associated filters are applied to allow data into this channel. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in [4,6]. The filters in this group are applied to all packets on the local network segment attached to the identified interface. This object may not be modified if the associated channelStatus object is equal to valid(1). |
| INT channelIndex | 1.3.6.1.2.1.16.7.2.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the channel table. Each such entry defines one channel, a logical data and event stream. |
| CTR channelMatches | 1.3.6.1.2.1.16.7.2.1.9 | Counter | read-only | The number of times this channel has matched a packet. Note that this object is updated even when channelDataControl is set to off. |
| STR channelOwner | 1.3.6.1.2.1.16.7.2.1.11 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| ENT channelStatus | 1.3.6.1.2.1.16.7.2.1.12 | EntryStatus | read-write | The status of this channel entry. |
| channelTable | 1.3.6.1.2.1.16.7.2 | not-accessible | A list of packet channel entries. | |
| INT channelTurnOffEventIndex | 1.3.6.1.2.1.16.7.2.1.6 | INTEGER | read-write | The value of this object identifies the event that is configured to turn the associated channelDataControl from on to off when the event is generated. The event identified by a particular value of this object is the same event as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In fact, if no event is intended for this channel, channelTurnOffEventIndex must be set to zero, a non-existent event index. This object may not be modified if the associated channelStatus object is equal to valid(1). |
| INT channelTurnOnEventIndex | 1.3.6.1.2.1.16.7.2.1.5 | INTEGER | read-write | The value of this object identifies the event that is configured to turn the associated channelDataControl from off to on when the event is generated. The event identified by a particular value of this object is the same event as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In fact, if no event is intended for this channel, channelTurnOnEventIndex must be set to zero, a non-existent event index. This object may not be modified if the associated channelStatus object is equal to valid(1). |
| CTR etherHistoryBroadcastPkts | 1.3.6.1.2.1.16.2.2.1.7 | Counter | read-only | The number of good packets received during this sampling interval that were directed to the broadcast address. |
| CTR etherHistoryCollisions | 1.3.6.1.2.1.16.2.2.1.14 | Counter | read-only | The best estimate of the total number of collisions on this Ethernet segment during this interval. |
| CTR etherHistoryCRCAlignErrors | 1.3.6.1.2.1.16.2.2.1.9 | Counter | read-only | The number of packets received during this sampling interval that had a length (excluding framing bits but including FCS octets) between 64 and 1518 octets, inclusive, but were not an integral number of octets in length or had a bad Frame Check Sequence (FCS). |
| CTR etherHistoryDropEvents | 1.3.6.1.2.1.16.2.2.1.4 | Counter | read-only | The total number of events in which packets were dropped by the probe due to lack of resources during this interval. Note that this number is not necessarily the number of packets dropped, it is just the number of times this condition has been detected. |
| etherHistoryEntry | 1.3.6.1.2.1.16.2.2.1 | not-accessible | An historical sample of Ethernet statistics on a particular Ethernet interface. This sample is associated with the historyControlEntry which set up the parameters for a regular collection of these samples. | |
| CTR etherHistoryFragments | 1.3.6.1.2.1.16.2.2.1.12 | Counter | read-only | The total number of packets received during this sampling interval that were not an integral number of octets in length or that had a bad Frame Check Sequence (FCS), and were less than 64 octets in length (excluding framing bits but including FCS octets). |
| INT etherHistoryIndex | 1.3.6.1.2.1.16.2.2.1.1 | INTEGER | read-only | The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. |
| TIK etherHistoryIntervalStart | 1.3.6.1.2.1.16.2.2.1.3 | TimeTicks | read-only | The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of the time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collecting the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval. |
| CTR etherHistoryJabbers | 1.3.6.1.2.1.16.2.2.1.13 | Counter | read-only | The number of packets received during this interval that were longer than 1518 octets (excluding framing bits but including FCS octets), and were not an integral number of octets in length or had a bad Frame Check Sequence (FCS). |
| CTR etherHistoryMulticastPkts | 1.3.6.1.2.1.16.2.2.1.8 | Counter | read-only | The number of good packets received during this sampling interval that were directed to a multicast address. Note that this number does not include packets addressed to the broadcast address. |
| CTR etherHistoryOctets | 1.3.6.1.2.1.16.2.2.1.5 | Counter | read-only | The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). |
| CTR etherHistoryOversizePkts | 1.3.6.1.2.1.16.2.2.1.11 | Counter | read-only | The number of packets received during this interval that were longer than 1518 octets (excluding framing bits but including FCS octets) but were otherwise well formed. |
| CTR etherHistoryPkts | 1.3.6.1.2.1.16.2.2.1.6 | Counter | read-only | The number of packets (including error packets) received during this sampling interval. |
| INT etherHistorySampleIndex | 1.3.6.1.2.1.16.2.2.1.2 | INTEGER | read-only | An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. |
| etherHistoryTable | 1.3.6.1.2.1.16.2.2 | not-accessible | A list of Ethernet history entries. | |
| CTR etherHistoryUndersizePkts | 1.3.6.1.2.1.16.2.2.1.10 | Counter | read-only | The number of packets received during this interval that were less than 64 octets long (excluding framing bits but including FCS octets) and were otherwise well formed. |
| INT etherHistoryUtilization | 1.3.6.1.2.1.16.2.2.1.15 | INTEGER | read-only | The best estimate of the mean physical layer network utilization on this interface during this interval, in hundredths of a percent. |
| CTR etherStatsBroadcastPkts | 1.3.6.1.2.1.16.1.1.1.6 | Counter | read-only | The total number of good packets received that were directed to the broadcast address. |
| CTR etherStatsCollisions | 1.3.6.1.2.1.16.1.1.1.13 | Counter | read-only | The best estimate of the total number of collisions on this Ethernet segment. |
| CTR etherStatsCRCAlignErrors | 1.3.6.1.2.1.16.1.1.1.8 | Counter | read-only | The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but were not an integral number of octets in length or had a bad Frame Check Sequence (FCS). |
| OID etherStatsDataSource | 1.3.6.1.2.1.16.1.1.1.2 | OBJECT IDENTIFIER | read-write | This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated etherStatsStatus object is equal to valid(1). |
| CTR etherStatsDropEvents | 1.3.6.1.2.1.16.1.1.1.3 | Counter | read-only | The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected. |
| etherStatsEntry | 1.3.6.1.2.1.16.1.1.1 | not-accessible | A collection of statistics kept for a particular Ethernet interface. | |
| CTR etherStatsFragments | 1.3.6.1.2.1.16.1.1.1.11 | Counter | read-only | The total number of packets received that were not an integral number of octets in length or that had a bad Frame Check Sequence (FCS), and were less than 64 octets in length (excluding framing bits but including FCS octets). |
| INT etherStatsIndex | 1.3.6.1.2.1.16.1.1.1.1 | INTEGER | read-only | The value of this object uniquely identifies this etherStats entry. |
| CTR etherStatsJabbers | 1.3.6.1.2.1.16.1.1.1.12 | Counter | read-only | The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and were not an integral number of octets in length or had a bad Frame Check Sequence (FCS). |
| CTR etherStatsMulticastPkts | 1.3.6.1.2.1.16.1.1.1.7 | Counter | read-only | The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. |
| CTR etherStatsOctets | 1.3.6.1.2.1.16.1.1.1.4 | Counter | read-only | The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). |
| CTR etherStatsOversizePkts | 1.3.6.1.2.1.16.1.1.1.10 | Counter | read-only | The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. |
| STR etherStatsOwner | 1.3.6.1.2.1.16.1.1.1.20 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| CTR etherStatsPkts | 1.3.6.1.2.1.16.1.1.1.5 | Counter | read-only | The total number of packets (including error packets) received. |
| CTR etherStatsPkts1024to1518Octets | 1.3.6.1.2.1.16.1.1.1.19 | Counter | read-only | The total number of packets (including error packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). |
| CTR etherStatsPkts128to255Octets | 1.3.6.1.2.1.16.1.1.1.16 | Counter | read-only | The total number of packets (including error packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets). |
| CTR etherStatsPkts256to511Octets | 1.3.6.1.2.1.16.1.1.1.17 | Counter | read-only | The total number of packets (including error packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets). |
| CTR etherStatsPkts512to1023Octets | 1.3.6.1.2.1.16.1.1.1.18 | Counter | read-only | The total number of packets (including error packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets). |
| CTR etherStatsPkts64Octets | 1.3.6.1.2.1.16.1.1.1.14 | Counter | read-only | The total number of packets (including error packets) received that were 64 octets in length (excluding framing bits but including FCS octets). |
| CTR etherStatsPkts65to127Octets | 1.3.6.1.2.1.16.1.1.1.15 | Counter | read-only | The total number of packets (including error packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). |
| ENT etherStatsStatus | 1.3.6.1.2.1.16.1.1.1.21 | EntryStatus | read-write | The status of this etherStats entry. |
| etherStatsTable | 1.3.6.1.2.1.16.1.1 | not-accessible | A list of Ethernet statistics entries. | |
| CTR etherStatsUndersizePkts | 1.3.6.1.2.1.16.1.1.1.9 | Counter | read-only | The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. |
| event | 1.3.6.1.2.1.16.9 | |||
| OCT eventCommunity | 1.3.6.1.2.1.16.9.1.1.4 | OCTET STRING | read-write | If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string. In the future this table will be extended to include the party security mechanism. This object shall be set to a string of length zero if it is intended that that mechanism be used to specify the destination of the trap. |
| STR eventDescription | 1.3.6.1.2.1.16.9.1.1.2 | DisplayString | read-write | A comment describing this event entry. |
| eventEntry | 1.3.6.1.2.1.16.9.1.1 | not-accessible | A set of parameters that describe an event to be generated when certain conditions are met. | |
| INT eventIndex | 1.3.6.1.2.1.16.9.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur. |
| TIK eventLastTimeSent | 1.3.6.1.2.1.16.9.1.1.5 | TimeTicks | read-only | The value of sysUpTime at the time this event entry last generated an event. If this entry has not generated any events, this value will be zero. |
| STR eventOwner | 1.3.6.1.2.1.16.9.1.1.6 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device |
| ENT eventStatus | 1.3.6.1.2.1.16.9.1.1.7 | EntryStatus | read-write | The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent. |
| eventTable | 1.3.6.1.2.1.16.9.1 | not-accessible | A list of events to be generated. | |
| INT eventType | 1.3.6.1.2.1.16.9.1.1.3 | INTEGER | read-write | The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations. |
| NTF fallingAlarm | 1.3.6.1.2.1.16.0.2 | The SNMP trap that is generated when an alarm entry crosses its falling threshold and generates an event that is configured for sending SNMP traps. | ||
| filter | 1.3.6.1.2.1.16.7 | |||
| INT filterChannelIndex | 1.3.6.1.2.1.16.7.1.1.2 | INTEGER | read-write | This object identifies the channel of which this filter is a part. The filters identified by a particular value of this object are associated with the same channel as identified by the same value of the channelIndex object. |
| filterEntry | 1.3.6.1.2.1.16.7.1.1 | not-accessible | A set of parameters for a packet filter applied on a particular interface. | |
| INT filterIndex | 1.3.6.1.2.1.16.7.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the filter table. Each such entry defines one filter that is to be applied to every packet received on an interface. |
| STR filterOwner | 1.3.6.1.2.1.16.7.1.1.10 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| OCT filterPktData | 1.3.6.1.2.1.16.7.1.1.4 | OCTET STRING | read-write | The data that is to be matched with the input packet. For each packet received, this filter and the accompanying filterPktDataMask and filterPktDataNotMask will be adjusted for the offset. The only bits relevant to this match algorithm are those that have the corresponding filterPktDataMask bit equal to one. The following three rules are then applied to every packet: (1) If the packet is too short and does not have data corresponding to part of the filterPktData, the packet will fail this data match. (2) For each relevant bit from the packet with the corresponding filterPktDataNotMask bit set to zero, if the bit from the packet is not equal to the corresponding bit from the filterPktData, then the packet will fail this data match. (3) If for every relevant bit from the packet with the corresponding filterPktDataNotMask bit set to one, the bit from the packet is equal to the corresponding bit from the filterPktData, then the packet will fail this data match. Any packets that have not failed any of the three matches above have passed this data match. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| OCT filterPktDataMask | 1.3.6.1.2.1.16.7.1.1.5 | OCTET STRING | read-write | The mask that is applied to the match process. After adjusting this mask for the offset, only those bits in the received packet that correspond to bits set in this mask are relevant for further processing by the match algorithm. The offset is applied to filterPktDataMask in the same way it is applied to the filter. For the purposes of the matching algorithm, if the associated filterPktData object is longer than this mask, this mask is conceptually extended with '1' bits until it reaches the length of the filterPktData object. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| OCT filterPktDataNotMask | 1.3.6.1.2.1.16.7.1.1.6 | OCTET STRING | read-write | The inversion mask that is applied to the match process. After adjusting this mask for the offset, those relevant bits in the received packet that correspond to bits cleared in this mask must all be equal to their corresponding bits in the filterPktData object for the packet to be accepted. In addition, at least one of those relevant bits in the received packet that correspond to bits set in this mask must be different to its corresponding bit in the filterPktData object. For the purposes of the matching algorithm, if the associated filterPktData object is longer than this mask, this mask is conceptually extended with '0' bits until it reaches the length of the filterPktData object. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| INT filterPktDataOffset | 1.3.6.1.2.1.16.7.1.1.3 | INTEGER | read-write | The offset from the beginning of each packet where a match of packet data will be attempted. This offset is measured from the point in the physical layer packet after the framing bits, if any. For example, in an Ethernet frame, this point is at the beginning of the destination MAC address. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| INT filterPktStatus | 1.3.6.1.2.1.16.7.1.1.7 | INTEGER | read-write | The status that is to be matched with the input packet. The only bits relevant to this match algorithm are those that have the corresponding filterPktStatusMask bit equal to one. The following two rules are then applied to every packet: (1) For each relevant bit from the packet status with the corresponding filterPktStatusNotMask bit set to zero, if the bit from the packet status is not equal to the corresponding bit from the filterPktStatus, then the packet will fail this status match. (2) If for every relevant bit from the packet status with the corresponding filterPktStatusNotMask bit set to one, the bit from the packet status is equal to the corresponding bit from the filterPktStatus, then the packet will fail this status match. Any packets that have not failed either of the two matches above have passed this status match. The value of the packet status is a sum. This sum initially takes the value zero. Then, for each error, E, that has been discovered in this packet, 2 raised to a value representing E is added to the sum. The errors and the bits that represent them are dependent on the media type of the interface that this channel is receiving packets from. The errors defined for a packet captured off of an Ethernet interface are as follows: bit # Error 0 Packet is longer than 1518 octets 1 Packet is shorter than 64 octets 2 Packet experienced a CRC or Alignment error For example, an Ethernet fragment would have a value of 6 (2^1 + 2^2). As this MIB is expanded to new media types, this object will have other media-specific errors defined. For the purposes of this status matching algorithm, if the packet status is longer than this object, filterPktStatus this object is conceptually extended with '0' bits until it reaches the size of the packet status. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| INT filterPktStatusMask | 1.3.6.1.2.1.16.7.1.1.8 | INTEGER | read-write | The mask that is applied to the status match process. Only those bits in the received packet that correspond to bits set in this mask are relevant for further processing by the status match algorithm. For the purposes of the matching algorithm, if the associated filterPktStatus object is longer than this mask, this mask is conceptually extended with '1' bits until it reaches the size of the filterPktStatus. In addition, if a packet status is longer than this mask, this mask is conceptually extended with '0' bits until it reaches the size of the packet status. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| INT filterPktStatusNotMask | 1.3.6.1.2.1.16.7.1.1.9 | INTEGER | read-write | The inversion mask that is applied to the status match process. Those relevant bits in the received packet status that correspond to bits cleared in this mask must all be equal to their corresponding bits in the filterPktStatus object for the packet to be accepted. In addition, at least one of those relevant bits in the received packet status that correspond to bits set in this mask must be different to its corresponding bit in the filterPktStatus object for the packet to be accepted. For the purposes of the matching algorithm, if the associated filterPktStatus object or a packet status is longer than this mask, this mask is conceptually extended with '0' bits until it reaches the longer of the lengths of the filterPktStatus object and the packet status. This object may not be modified if the associated filterStatus object is equal to valid(1). |
| ENT filterStatus | 1.3.6.1.2.1.16.7.1.1.11 | EntryStatus | read-write | The status of this filter entry. |
| filterTable | 1.3.6.1.2.1.16.7.1 | not-accessible | A list of packet filter entries. | |
| history | 1.3.6.1.2.1.16.2 | |||
| INT historyControlBucketsGranted | 1.3.6.1.2.1.16.2.1.1.4 | INTEGER | read-only | The number of discrete sampling intervals over which data shall be saved in the part of the media-specific table associated with this historyControl entry. When the associated historyControlBucketsRequested object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular probe implementation and available resources. The probe must not lower this value except as a result of a modification to the associated historyControlBucketsRequested object. There will be times when the actual number of buckets associated with this entry is less than the value of this object. In this case, at the end of each sampling interval, a new bucket will be added to the media-specific table. When the number of buckets reaches the value of this object and a new bucket is to be added to the media-specific table, the oldest bucket associated with this historyControlEntry shall be deleted by the agent so that the new bucket can be added. When the value of this object changes to a value less than the current value, entries are deleted from the media-specific table associated with this historyControlEntry. Enough of the oldest of these entries shall be deleted by the agent so that their number remains less than or equal to the new value of this object. When the value of this object changes to a value greater than the current value, the number of associated media-specific entries may be allowed to grow. |
| INT historyControlBucketsRequested | 1.3.6.1.2.1.16.2.1.1.3 | INTEGER | read-write | The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControl entry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources. |
| OID historyControlDataSource | 1.3.6.1.2.1.16.2.1.1.2 | OBJECT IDENTIFIER | read-write | This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated historyControlStatus object is equal to valid(1). |
| historyControlEntry | 1.3.6.1.2.1.16.2.1.1 | not-accessible | A list of parameters that set up a periodic sampling of statistics. | |
| INT historyControlIndex | 1.3.6.1.2.1.16.2.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device. |
| INT historyControlInterval | 1.3.6.1.2.1.16.2.1.1.5 | INTEGER | read-write | The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControl entry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1). |
| STR historyControlOwner | 1.3.6.1.2.1.16.2.1.1.6 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| ENT historyControlStatus | 1.3.6.1.2.1.16.2.1.1.7 | EntryStatus | read-write | The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1). |
| historyControlTable | 1.3.6.1.2.1.16.2.1 | not-accessible | A list of history control entries. | |
| OCT hostAddress | 1.3.6.1.2.1.16.4.2.1.1 | OCTET STRING | read-only | The physical address of this host. |
| OID hostControlDataSource | 1.3.6.1.2.1.16.4.1.1.2 | OBJECT IDENTIFIER | read-write | This object identifies the source of the data for this instance of the host function. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated hostControlStatus object is equal to valid(1). |
| hostControlEntry | 1.3.6.1.2.1.16.4.1.1 | not-accessible | A list of parameters that set up the discovery of hosts on a particular interface and the collection of statistics about these hosts. | |
| INT hostControlIndex | 1.3.6.1.2.1.16.4.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the hostControl table. Each such entry defines a function that discovers hosts on a particular interface and places statistics about them in the hostTable and the hostTimeTable on behalf of this hostControlEntry. |
| TIK hostControlLastDeleteTime | 1.3.6.1.2.1.16.4.1.1.4 | TimeTicks | read-only | The value of sysUpTime when the last entry was deleted from the portion of the hostTable associated with this hostControlEntry. If no deletions have occurred, this value shall be zero. |
| STR hostControlOwner | 1.3.6.1.2.1.16.4.1.1.5 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| ENT hostControlStatus | 1.3.6.1.2.1.16.4.1.1.6 | EntryStatus | read-write | The status of this hostControl entry. If this object is not equal to valid(1), all associated entries in the hostTable, hostTimeTable, and the hostTopNTable shall be deleted by the agent. |
| hostControlTable | 1.3.6.1.2.1.16.4.1 | not-accessible | A list of host table control entries. | |
| INT hostControlTableSize | 1.3.6.1.2.1.16.4.1.1.3 | INTEGER | read-only | The number of hostEntries in the hostTable and the hostTimeTable associated with this hostControlEntry. |
| INT hostCreationOrder | 1.3.6.1.2.1.16.4.2.1.2 | INTEGER | read-only | An index that defines the relative ordering of the creation time of hosts captured for a particular hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes is based on the order of each entry's insertion into the table, in which entries added earlier have a lower index value than entries added later. It is important to note that the order for a particular entry may change as an (earlier) entry is deleted from the table. Because this order may change, management stations should make use of the hostControlLastDeleteTime variable in the hostControlEntry associated with the relevant portion of the hostTable. By observing this variable, the management station may detect the circumstances where a previous association between a value of hostCreationOrder and a hostEntry may no longer hold. |
| hostEntry | 1.3.6.1.2.1.16.4.2.1 | not-accessible | A collection of statistics for a particular host that has been discovered on an interface of this device. | |
| INT hostIndex | 1.3.6.1.2.1.16.4.2.1.3 | INTEGER | read-only | The set of collected host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex. |
| CTR hostInOctets | 1.3.6.1.2.1.16.4.2.1.6 | Counter | read-only | The number of octets transmitted to this address since it was added to the hostTable (excluding framing bits but including FCS octets), except for those octets in packets that contained errors. |
| CTR hostInPkts | 1.3.6.1.2.1.16.4.2.1.4 | Counter | read-only | The number of packets without errors transmitted to this address since it was added to the hostTable. |
| CTR hostOutBroadcastPkts | 1.3.6.1.2.1.16.4.2.1.9 | Counter | read-only | The number of good packets transmitted by this address that were directed to the broadcast address since this host was added to the hostTable. |
| CTR hostOutErrors | 1.3.6.1.2.1.16.4.2.1.8 | Counter | read-only | The number of error packets transmitted by this address since this host was added to the hostTable. |
| CTR hostOutMulticastPkts | 1.3.6.1.2.1.16.4.2.1.10 | Counter | read-only | The number of good packets transmitted by this address that were directed to a multicast address since this host was added to the hostTable. Note that this number does not include packets directed to the broadcast address. |
| CTR hostOutOctets | 1.3.6.1.2.1.16.4.2.1.7 | Counter | read-only | The number of octets transmitted by this address since it was added to the hostTable (excluding framing bits but including FCS octets), including those octets in packets that contained errors. |
| CTR hostOutPkts | 1.3.6.1.2.1.16.4.2.1.5 | Counter | read-only | The number of packets including errors transmitted by this address since it was added to the hostTable. |
| hosts | 1.3.6.1.2.1.16.4 | |||
| hostTable | 1.3.6.1.2.1.16.4.2 | not-accessible | A list of host entries. | |
| OCT hostTimeAddress | 1.3.6.1.2.1.16.4.3.1.1 | OCTET STRING | read-only | The physical address of this host. |
| INT hostTimeCreationOrder | 1.3.6.1.2.1.16.4.3.1.2 | INTEGER | read-only | An index that uniquely identifies an entry in the hostTime table among those entries associated with the same hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes is based on the order of each entry's insertion into the table, in which entries added earlier have a lower index value than entries added later. Thus the management station has the ability to learn of new entries added to this table without downloading the entire table. It is important to note that the index for a particular entry may change as an (earlier) entry is deleted from the table. Because this order may change, management stations should make use of the hostControlLastDeleteTime variable in the hostControlEntry associated with the relevant portion of the hostTimeTable. By observing this variable, the management station may detect the circumstances where a download of the table may have missed entries, and where a previous association between a value of hostTimeCreationOrder and a hostTimeEntry may no longer hold. |
| hostTimeEntry | 1.3.6.1.2.1.16.4.3.1 | not-accessible | A collection of statistics for a particular host that has been discovered on an interface of this device. This collection includes the relative ordering of the creation time of this object. | |
| INT hostTimeIndex | 1.3.6.1.2.1.16.4.3.1.3 | INTEGER | read-only | The set of collected host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex. |
| CTR hostTimeInOctets | 1.3.6.1.2.1.16.4.3.1.6 | Counter | read-only | The number of octets transmitted to this address since it was added to the hostTimeTable (excluding framing bits but including FCS octets), except for those octets in packets that contained errors. |
| CTR hostTimeInPkts | 1.3.6.1.2.1.16.4.3.1.4 | Counter | read-only | The number of packets without errors transmitted to this address since it was added to the hostTimeTable. |
| CTR hostTimeOutBroadcastPkts | 1.3.6.1.2.1.16.4.3.1.9 | Counter | read-only | The number of good packets transmitted by this address that were directed to the broadcast address since this host was added to the hostTimeTable. |
| CTR hostTimeOutErrors | 1.3.6.1.2.1.16.4.3.1.8 | Counter | read-only | The number of error packets transmitted by this address since this host was added to the hostTimeTable. |
| CTR hostTimeOutMulticastPkts | 1.3.6.1.2.1.16.4.3.1.10 | Counter | read-only | The number of good packets transmitted by this address that were directed to a multicast address since this host was added to the hostTimeTable. Note that this number does not include packets directed to the broadcast address. |
| CTR hostTimeOutOctets | 1.3.6.1.2.1.16.4.3.1.7 | Counter | read-only | The number of octets transmitted by this address since it was added to the hostTimeTable (excluding framing bits but including FCS octets), including those octets in packets that contained errors. |
| CTR hostTimeOutPkts | 1.3.6.1.2.1.16.4.3.1.5 | Counter | read-only | The number of packets including errors transmitted by this address since it was added to the hostTimeTable. |
| hostTimeTable | 1.3.6.1.2.1.16.4.3 | not-accessible | A list of time-ordered host table entries. | |
| hostTopN | 1.3.6.1.2.1.16.5 | |||
| OCT hostTopNAddress | 1.3.6.1.2.1.16.5.2.1.3 | OCTET STRING | read-only | The physical address of this host. |
| hostTopNControlEntry | 1.3.6.1.2.1.16.5.1.1 | not-accessible | A set of parameters that control the creation of a report of the top N hosts according to several metrics. | |
| INT hostTopNControlIndex | 1.3.6.1.2.1.16.5.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the hostTopNControl table. Each such entry defines one top N report prepared for one interface. |
| hostTopNControlTable | 1.3.6.1.2.1.16.5.1 | not-accessible | A list of top N host control entries. | |
| INT hostTopNDuration | 1.3.6.1.2.1.16.5.1.1.5 | INTEGER | read-only | The number of seconds that this report has collected during the last sampling interval, or if this report is currently being collected, the number of seconds that this report is being collected during this sampling interval. When the associated hostTopNTimeRemaining object is set, this object shall be set by the probe to the same value and shall not be modified until the next time the hostTopNTimeRemaining is set. This value shall be zero if no reports have been requested for this hostTopNControlEntry. |
| hostTopNEntry | 1.3.6.1.2.1.16.5.2.1 | not-accessible | A set of statistics for a host that is part of a top N report. | |
| INT hostTopNGrantedSize | 1.3.6.1.2.1.16.5.1.1.7 | INTEGER | read-only | The maximum number of hosts in the top N table. When the associated hostTopNRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated hostTopNRequestedSize object. Hosts with the highest value of hostTopNRate shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more hosts. |
| INT hostTopNHostIndex | 1.3.6.1.2.1.16.5.1.1.2 | INTEGER | read-write | The host table for which a top N report will be prepared on behalf of this entry. The host table identified by a particular value of this index is associated with the same host table as identified by the same value of hostIndex. This object may not be modified if the associated hostTopNStatus object is equal to valid(1). |
| INT hostTopNIndex | 1.3.6.1.2.1.16.5.2.1.2 | INTEGER | read-only | An index that uniquely identifies an entry in the hostTopN table among those in the same report. This index is between 1 and N, where N is the number of entries in this table. Increasing values of hostTopNIndex shall be assigned to entries with decreasing values of hostTopNRate until index N is assigned to the entry with the lowest value of hostTopNRate or there are no more hostTopNEntries. |
| STR hostTopNOwner | 1.3.6.1.2.1.16.5.1.1.9 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| INT hostTopNRate | 1.3.6.1.2.1.16.5.2.1.4 | INTEGER | read-only | The amount of change in the selected variable during this sampling interval. The selected variable is this host's instance of the object selected by hostTopNRateBase. |
| INT hostTopNRateBase | 1.3.6.1.2.1.16.5.1.1.3 | INTEGER | read-write | The variable for each host that the hostTopNRate variable is based upon. This object may not be modified if the associated hostTopNStatus object is equal to valid(1). |
| INT hostTopNReport | 1.3.6.1.2.1.16.5.2.1.1 | INTEGER | read-only | This object identifies the top N report of which this entry is a part. The set of hosts identified by a particular value of this object is part of the same report as identified by the same value of the hostTopNControlIndex object. |
| INT hostTopNRequestedSize | 1.3.6.1.2.1.16.5.1.1.6 | INTEGER | read-write | The maximum number of hosts requested for the top N table. When this object is created or modified, the probe should set hostTopNGrantedSize as closely to this object as is possible for the particular probe implementation and available resources. |
| TIK hostTopNStartTime | 1.3.6.1.2.1.16.5.1.1.8 | TimeTicks | read-only | The value of sysUpTime when this top N report was last started. In other words, this is the time that the associated hostTopNTimeRemaining object was modified to start the requested report. |
| ENT hostTopNStatus | 1.3.6.1.2.1.16.5.1.1.10 | EntryStatus | read-write | The status of this hostTopNControl entry. If this object is not equal to valid(1), all associated hostTopNEntries shall be deleted by the agent. |
| hostTopNTable | 1.3.6.1.2.1.16.5.2 | not-accessible | A list of top N host entries. | |
| INT hostTopNTimeRemaining | 1.3.6.1.2.1.16.5.1.1.4 | INTEGER | read-write | The number of seconds left in the report currently being collected. When this object is modified by the management station, a new collection is started, possibly aborting a currently running report. The new value is used as the requested duration of this report, which is loaded into the associated hostTopNDuration object. When this object is set to a non-zero value, any associated hostTopNEntries shall be made inaccessible by the monitor. While the value of this object is non-zero, it decrements by one per second until it reaches zero. During this time, all associated hostTopNEntries shall remain inaccessible. At the time that this object decrements to zero, the report is made accessible in the hostTopNTable. Thus, the hostTopN table needs to be created only at the end of the collection interval. |
| STR logDescription | 1.3.6.1.2.1.16.9.2.1.4 | DisplayString | read-only | An implementation dependent description of the event that activated this log entry. |
| logEntry | 1.3.6.1.2.1.16.9.2.1 | not-accessible | A set of data describing an event that has been logged. | |
| INT logEventIndex | 1.3.6.1.2.1.16.9.2.1.1 | INTEGER | read-only | The event entry that generated this log entry. The log identified by a particular value of this index is associated with the same eventEntry as identified by the same value of eventIndex. |
| INT logIndex | 1.3.6.1.2.1.16.9.2.1.2 | INTEGER | read-only | An index that uniquely identifies an entry in the log table amongst those generated by the same eventEntries. These indexes are assigned beginning with 1 and increase by one with each new log entry. The association between values of logIndex and logEntries is fixed for the lifetime of each logEntry. The agent may choose to delete the oldest instances of logEntry as required because of lack of memory. It is an implementation-specific matter as to when this deletion may occur. |
| logTable | 1.3.6.1.2.1.16.9.2 | not-accessible | A list of events that have been logged. | |
| TIK logTime | 1.3.6.1.2.1.16.9.2.1.3 | TimeTicks | read-only | The value of sysUpTime when this log entry was created. |
| matrix | 1.3.6.1.2.1.16.6 | |||
| OID matrixControlDataSource | 1.3.6.1.2.1.16.6.1.1.2 | OBJECT IDENTIFIER | read-write | This object identifies the source of the data from which this entry creates a traffic matrix. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in [4,6], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated matrixControlStatus object is equal to valid(1). |
| matrixControlEntry | 1.3.6.1.2.1.16.6.1.1 | not-accessible | Information about a traffic matrix on a particular interface. | |
| INT matrixControlIndex | 1.3.6.1.2.1.16.6.1.1.1 | INTEGER | read-only | An index that uniquely identifies an entry in the matrixControl table. Each such entry defines a function that discovers conversations on a particular interface and places statistics about them in the matrixSDTable and the matrixDSTable on behalf of this matrixControlEntry. |
| TIK matrixControlLastDeleteTime | 1.3.6.1.2.1.16.6.1.1.4 | TimeTicks | read-only | The value of sysUpTime when the last entry was deleted from the portion of the matrixSDTable or matrixDSTable associated with this matrixControlEntry. If no deletions have occurred, this value shall be zero. |
| STR matrixControlOwner | 1.3.6.1.2.1.16.6.1.1.5 | OwnerString | read-write | The entity that configured this entry and is therefore using the resources assigned to it. |
| ENT matrixControlStatus | 1.3.6.1.2.1.16.6.1.1.6 | EntryStatus | read-write | The status of this matrixControl entry. If this object is not equal to valid(1), all associated entries in the matrixSDTable and the matrixDSTable shall be deleted by the agent. |
| matrixControlTable | 1.3.6.1.2.1.16.6.1 | not-accessible | A list of information entries for the traffic matrix on each interface. | |
| INT matrixControlTableSize | 1.3.6.1.2.1.16.6.1.1.3 | INTEGER | read-only | The number of matrixSDEntries in the matrixSDTable for this interface. This must also be the value of the number of entries in the matrixDSTable for this interface. |
| OCT matrixDSDestAddress | 1.3.6.1.2.1.16.6.3.1.2 | OCTET STRING | read-only | The destination physical address. |
| matrixDSEntry | 1.3.6.1.2.1.16.6.3.1 | not-accessible | A collection of statistics for communications between two address on a particular interface. | |
| CTR matrixDSErrors | 1.3.6.1.2.1.16.6.3.1.6 | Counter | read-only | The number of error packets transmitted from the source address to the destination address. |
| INT matrixDSIndex | 1.3.6.1.2.1.16.6.3.1.3 | INTEGER | read-only | The set of collected matrix statistics of which this entry is a part. The set of matrix statistics identified by a particular value of this index is associated with the same matrixControlEntry as identified by the same value of matrixControlIndex. |
| CTR matrixDSOctets | 1.3.6.1.2.1.16.6.3.1.5 | Counter | read-only | The number of octets (excluding framing bits but including FCS octets) contained in all packets transmitted from the source address to the destination address. |
| CTR matrixDSPkts | 1.3.6.1.2.1.16.6.3.1.4 | Counter | read-only | The number of packets transmitted from the source address to the destination address (this number includes error packets). |
| OCT matrixDSSourceAddress | 1.3.6.1.2.1.16.6.3.1.1 | OCTET STRING | read-only | The source physical address. |
| matrixDSTable | 1.3.6.1.2.1.16.6.3 | not-accessible | A list of traffic matrix entries indexed by destination and source MAC address. | |
| OCT matrixSDDestAddress | 1.3.6.1.2.1.16.6.2.1.2 | OCTET STRING | read-only | The destination physical address. |
| matrixSDEntry | 1.3.6.1.2.1.16.6.2.1 | not-accessible | A collection of statistics for communications between two addresses on a particular interface. | |
| CTR matrixSDErrors | 1.3.6.1.2.1.16.6.2.1.6 | Counter | read-only | The number of error packets transmitted from the source address to the destination address. |
| INT matrixSDIndex | 1.3.6.1.2.1.16.6.2.1.3 | INTEGER | read-only | The set of collected matrix statistics of which this entry is a part. The set of matrix statistics identified by a particular value of this index is associated with the same matrixControlEntry as identified by the same value of matrixControlIndex. |
| CTR matrixSDOctets | 1.3.6.1.2.1.16.6.2.1.5 | Counter | read-only | The number of octets (excluding framing bits but including FCS octets) contained in all packets transmitted from the source address to the destination address. |
| CTR matrixSDPkts | 1.3.6.1.2.1.16.6.2.1.4 | Counter | read-only | The number of packets transmitted from the source address to the destination address (this number includes error packets). |
| OCT matrixSDSourceAddress | 1.3.6.1.2.1.16.6.2.1.1 | OCTET STRING | read-only | The source physical address. |
| matrixSDTable | 1.3.6.1.2.1.16.6.2 | not-accessible | A list of traffic matrix entries indexed by source and destination MAC address. | |
| NTF risingAlarm | 1.3.6.1.2.1.16.0.1 | The SNMP trap that is generated when an alarm entry crosses its rising threshold and generates an event that is configured for sending SNMP traps. | ||
| rmon | 1.3.6.1.2.1.16 | |||
| statistics | 1.3.6.1.2.1.16.1 |
RFC description
Defines the original Remote Network Monitoring (RMON) MIB for remotely monitoring LAN traffic statistics, packet capture, alarms, host tables, and event handling.
Start monitoring vendor-neutral, standards-based RMON MIB, RMON-capable network probes and switches monitoring Ethernet with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.