RETIX-SWITCHSTAKII-MIB

All MIBs › RETIX-SWITCHSTAKII-MIB

Description: MIB for Retix SwitchStakII stackable Ethernet switches, covering unit profile, stacking bus, VLAN configuration, and modular I/O cards including 10BaseT, FastEthernet, and ATM

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RETIX-SWITCHSTAKII-MIB?

RETIX-SWITCHSTAKII-MIB is a legacy Retix (enterprise OID 72) proprietary MIB for the SwitchStak II chassis, reporting board identity and stack-bus/VLAN configuration. Its objects cover base/IO1/IO2 module identity, base boot-firmware/software version, an error log, stack-bus I/O port/speed/node-address, stack-ring operational status, a global VLAN enable/disable flag, and a port-VLAN table (port ID, VLAN ID, edit action). As a configuration/status MIB it lets an administrator confirm firmware version and per-port VLAN assignment on a legacy Retix SwitchStak II chassis. It is deployed on legacy Retix SwitchStak II chassis equipment. Engineers can download the RETIX-SWITCHSTAKII-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RETIX-SWITCHSTAKII-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Legacy Retix SwitchStak II chassis equipment

Monitoring Examples

An administrator checks portVLANEntryVLANID and stkbusRingOperationalStatus to confirm VLAN assignment and stack-ring health on a legacy Retix SwitchStak II chassis.

What Can Be Monitored

per-port VLAN assignment and stack-ring operational status

Imported Objects

From RFC1155-SMI

enterprises

From RFC1158-MIB

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks

From RFC1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
retix	1.3.6.1.4.1.72
switchStakII	1.3.6.1.4.1.72.20
unitProfile	1.3.6.1.4.1.72.20.1
INT baseModule	1.3.6.1.4.1.72.20.1.1	INTEGER	read-only	Identifies the type of main PCB installed.
INT io1Module	1.3.6.1.4.1.72.20.1.2	INTEGER	read-only	Identifies the type of card installed in the IO1 connector
INT io2Module	1.3.6.1.4.1.72.20.1.3	INTEGER	read-only	Identifies the type of card installed in the IO2 connector
baseUnit	1.3.6.1.4.1.72.20.2
INT baseBootFirmwareVersion	1.3.6.1.4.1.72.20.2.1	INTEGER	read-only	Version number of current boot firmware in decimal, (i.e. V01.00 is displayed as 256)
INT baseSoftwareVersion	1.3.6.1.4.1.72.20.2.2	INTEGER	read-only	Version number of current software in decimal, (i.e. V01.03 is displayed as 259)
INT baseErrorLog	1.3.6.1.4.1.72.20.2.3	INTEGER	read-write	A stored value indicating that the unit has experienced a fault. Log information is formatted as a four digit hex number. Set to zero to clear the logged fault. Record this value and call Retix technical support.
stakbus	1.3.6.1.4.1.72.20.3
INT stkbusIOPort	1.3.6.1.4.1.72.20.3.1	INTEGER	read-only	Represents the IO port containing a StakbusII card. Only one Stakbus card is permitted per unit
INT stkbusSpeed	1.3.6.1.4.1.72.20.3.2	INTEGER	read-only	Speed in Mbps of the installed Stakbus (StakbusII = 175Mbps).
INT stkbusNodeAddress	1.3.6.1.4.1.72.20.3.3	INTEGER	read-only	Address of the Stakbus interface as set on front panel dial (0..15).
INT stkbusRingOperationalStatus	1.3.6.1.4.1.72.20.3.4	INTEGER	read-only	The status of the Retix Stakbus interface ring.
vlan	1.3.6.1.4.1.72.20.4
vlanConfig	1.3.6.1.4.1.72.20.4.1
INT vlanEnableDisable	1.3.6.1.4.1.72.20.4.1.1	INTEGER	read-write	Enables or Disables VLAN operation on this unit.
portVLANTable	1.3.6.1.4.1.72.20.4.1.2		not-accessible	Table of port based VLAN configurations. Entries (rows) are added to the table by issuing a SET command with the EnableAdd value for the portVLANEntryEdit object. The new row is created using the instantiations.
portVLANEntry	1.3.6.1.4.1.72.20.4.1.2.1		not-accessible	This is an entry in the portVLANTable.
INT portVLANEntryPortID	1.3.6.1.4.1.72.20.4.1.2.1.1	INTEGER	read-write	Port number for this VLAN configuration.
INT portVLANEntryVLANID	1.3.6.1.4.1.72.20.4.1.2.1.2	INTEGER	read-write	VLAN number or ID.
INT portVLANEntryEdit	1.3.6.1.4.1.72.20.4.1.2.1.3	INTEGER	read-write	When set to enableAdd(1) the instantiations will be used to create a new table entry (row). Existing entries can be disabled(2) or deleted (3).

RFC description

Vendor-private MIB for Retix Switch STak II intelligent Ethernet switch management and monitoring.

Start monitoring legacy Retix SwitchStak II chassis equipment (board identity/stack-bus/VLAN configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RETIX-SWITCHSTAKII-MIB

What Is RETIX-SWITCHSTAKII-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description