REDSTONE-ATM-MIB

All MIBs › REDSTONE-ATM-MIB

Organization: Redstone Communications, Inc.

Last Updated: 1999-08-04

Category: DSL and Broadband Access

Description: Manages ATM interface configuration, PVC parameters, and traffic statistics on Redstone routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDSTONE-ATM-MIB?

This is a vendor-specific MIB from Redstone Communications Inc. for managing ATM (Asynchronous Transfer Mode) interfaces on their routers. It exposes configuration data for ATM interfaces, including PVC/VC parameters, ILMI (Integrated Local Management Interface) polling settings, and layer associations to lower interfaces. Rather than physical environmental sensors, this MIB is used chiefly to monitor interface administrative/operational state (via row status and admin state) and ILMI negotiation health, reflecting the software/protocol status of the ATM link rather than hardware. It builds on standard interface indexing conventions and ATM industry standards like ILMI/UNI, tying rsAtmIfLowerIfIndex back to the IF-MIB ifTable. It is typically deployed on Redstone ATM-capable routers/switches in carrier or enterprise WAN edge environments where ATM PVCs are provisioned. Engineers can download the REDSTONE-ATM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDSTONE-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Redstone Communications ATM router
ATM WAN edge device

Monitoring Examples

An administrator would poll rsAtmIfTable/rsAtmIfEntry indexed by rsAtmIfIndex to check rsAtmIfRowStatus and rsAtmIfIlmiAdminState for each ATM interface, confirming the interface is active and ILMI is up. Watching rsAtmIfIlmiVpi/rsAtmIfIlmiVci/rsAtmIfIlmiVcd together with rsAtmIfIlmiPollFrequency helps detect ILMI negotiation failures or misconfigured VPI/VCI pairs. A mismatched rsAtmIfUniVersion could indicate a UNI version incompatibility between the Redstone router and the ATM switch it connects to.

What Can Be Monitored

ATM interface row status
ILMI admin state
ILMI VPI/VCI/VCD values
ILMI poll frequency
UNI version
lower-layer interface association

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From REDSTONE-SMI

rsMgmt

OBJECT-IDENTITY

From REDSTONE-TC

RsNextIfIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
rsAtmMIB	1.3.6.1.4.1.2773.2.8			The ATM MIB for the Redstone Communications Inc. enterprise.
rsAtmObjects	1.3.6.1.4.1.2773.2.8.1
rsAtmIfLayer	1.3.6.1.4.1.2773.2.8.1.1
RSN rsAtmNextIfIndex	1.3.6.1.4.1.2773.2.8.1.1.1	RsNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in rsAtmIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
rsAtmIfTable	1.3.6.1.4.1.2773.2.8.1.1.2		not-accessible	This table contains entries for ATM interfaces present in the system.
rsAtmIfEntry	1.3.6.1.4.1.2773.2.8.1.1.2.1		not-accessible	Each entry describes the characteristics of an ATM interface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
NUM rsAtmIfIndex	1.3.6.1.4.1.2773.2.8.1.1.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM interface. When creating entries in this table, suitable values for this object are determined by reading rsAtmNextIfIndex.
ROW rsAtmIfRowStatus	1.3.6.1.4.1.2773.2.8.1.1.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmIfRowStatus rsAtmIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmIfIndex must have been determined previously, by reading rsAtmNextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
NUM rsAtmIfLowerIfIndex	1.3.6.1.4.1.2773.2.8.1.1.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of an interface over which this ATM interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
I32 rsAtmIfIlmiVpi	1.3.6.1.4.1.2773.2.8.1.1.2.1.4	Integer32	read-write	The VPI of the Ilmi of a major ATM interface.
I32 rsAtmIfIlmiVci	1.3.6.1.4.1.2773.2.8.1.1.2.1.5	Integer32	read-write	The VCI of the Ilmi of a major ATM interface.
I32 rsAtmIfIlmiVcd	1.3.6.1.4.1.2773.2.8.1.1.2.1.6	Integer32	read-write	An integer identifier for the Ilmi, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
I32 rsAtmIfIlmiPollFrequency	1.3.6.1.4.1.2773.2.8.1.1.2.1.7	Integer32	read-write	Use to set the Interim Local Management Interface (ILMI) keepalive timer. This value sets the allowable time between POLL PDU transmissions if there are no pending sequence data PDUs. Use the value 0 to disable ILMI keepalives.
INT rsAtmIfIlmiAdminState	1.3.6.1.4.1.2773.2.8.1.1.2.1.8	INTEGER	read-write	The administrative status of ILMI in the ATM interface.
INT rsAtmIfUniVersion	1.3.6.1.4.1.2773.2.8.1.1.2.1.9	INTEGER	read-write	Use to specify the User Network Interface (UNI) the router should use when ILMI link auto determination is unsuccesful or ILMI is disabled.
rsAtmAal5IfLayer	1.3.6.1.4.1.2773.2.8.1.2
RSN rsAtmAal5NextIfIndex	1.3.6.1.4.1.2773.2.8.1.2.1	RsNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in rsAtmAal5IfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
rsAtmAal5IfTable	1.3.6.1.4.1.2773.2.8.1.2.2		not-accessible	This table contains entries for ATM AAL5 interfaces present in the system.
rsAtmAal5IfEntry	1.3.6.1.4.1.2773.2.8.1.2.2.1		not-accessible	Each entry describes the characteristics of an ATM AAL5 interface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
NUM rsAtmAal5IfIndex	1.3.6.1.4.1.2773.2.8.1.2.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM AAL5 interface. When creating entries in this table, suitable values for this object are determined by reading rsAtmAal5NextIfIndex.
ROW rsAtmAal5IfRowStatus	1.3.6.1.4.1.2773.2.8.1.2.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmAal5IfRowStatus rsAtmAal5IfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmAal5IfIndex must have been determined previously, by reading rsAtmAal5NextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
NUM rsAtmAal5IfLowerIfIndex	1.3.6.1.4.1.2773.2.8.1.2.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of an ATM interface over which this ATM AAL5 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
rsAtmSubIfLayer	1.3.6.1.4.1.2773.2.8.1.3
RSN rsAtmSubIfNextIfIndex	1.3.6.1.4.1.2773.2.8.1.3.1	RsNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in rsAtmSubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
rsAtmSubIfTable	1.3.6.1.4.1.2773.2.8.1.3.2		not-accessible	This table contains entries for ATM Subinterfaces present in the system.
rsAtmSubIfEntry	1.3.6.1.4.1.2773.2.8.1.3.2.1		not-accessible	Each entry describes the characteristics of an ATM Subinterface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
NUM rsAtmSubIfIndex	1.3.6.1.4.1.2773.2.8.1.3.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the ATM Subinterface. When creating entries in this table, suitable values for this object are determined by reading rsAtmSubNextIfIndex.
ROW rsAtmSubIfRowStatus	1.3.6.1.4.1.2773.2.8.1.3.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmSubIfRowStatus rsAtmSubIfLowerIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmSubIfIndex must have been determined previously, by reading rsAtmSubIfNextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
I32 rsAtmSubIfDistinguisher	1.3.6.1.4.1.2773.2.8.1.3.2.1.3	Integer32	read-create	An integer identifier for the sub interface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among sub interfaces configured on the same underlying ATM adaptation layer. The upper bound for the value is further constrained to be identical with the maximum number of sub interfaces supported by the lower interface. If this object is not configured, a value will be allocated internally and can be queried after table entry creation has succeeded.
NUM rsAtmSubIfLowerIfIndex	1.3.6.1.4.1.2773.2.8.1.3.2.1.4	InterfaceIndexOrZero	read-create	The ifIndex of an ATM AAL5 interface over which this ATM Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
rsAtmSubIfVccTable	1.3.6.1.4.1.2773.2.8.1.3.3		not-accessible	This table contains entries for ATM VCCs configured on ATM Subinterfaces present in the system. An implementation may constrain the number of VCCs permitted to be configured per ATM Subinterface; in particular, an implementation may restrict each ATM Subinterface to have a single VCC. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
rsAtmSubIfVccEntry	1.3.6.1.4.1.2773.2.8.1.3.3.1		not-accessible	Each entry describes the characteristics of an ATM Subinterface VCC.
I32 rsAtmSubIfVccVpi	1.3.6.1.4.1.2773.2.8.1.3.3.1.1	Integer32	not-accessible	The VPI of the ATM VCC used by this subinterface.
I32 rsAtmSubIfVccVci	1.3.6.1.4.1.2773.2.8.1.3.3.1.2	Integer32	not-accessible	The VCI of the ATM VCC used by this subinterface.
ROW rsAtmSubIfVccRowStatus	1.3.6.1.4.1.2773.2.8.1.3.3.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmSubIfVccRowStatus In addition, when creating an entry the following conditions must hold: The ATM Subinterface identified by rsAtmSubIfIndex must exist. A positive value configured for rsAtmSubIfVccVcd must not already be assigned to an existing VCC. For each value of rsAtmSubIfVccServiceCategory, additional dependent objects in the entry require configuration as identified here: rsAtmSubIfVccServiceCategory Requires configuration of: ------------------------------------------------------------ ubr ubrPcr rsAtmSubIfVccPcr nrtVbr rsAtmSubIfVccPcr rsAtmSubIfVccScr rsAtmSubIfVccMbs ------------------------------------------------------------ Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
I32 rsAtmSubIfVccVcd	1.3.6.1.4.1.2773.2.8.1.3.3.1.4	Integer32	read-create	An integer identifier for the circuit, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among VCCs configured on the same underlying ATM interface. The upper bound for the value is further constrained to be identical with the maximum number of VCCs supported by the underlying ATM interface. If this object is not configured, or is configured with a value of zero, a value will be allocated internally and can be queried after table entry creation has succeeded.
INT rsAtmSubIfVccType	1.3.6.1.4.1.2773.2.8.1.3.3.1.5	INTEGER	read-create	Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM.
INT rsAtmSubIfVccServiceCategory	1.3.6.1.4.1.2773.2.8.1.3.3.1.6	INTEGER	read-create	Service category for this circuit: ubr Unspecified bit rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable Bit Rate.
I32 rsAtmSubIfVccPcr	1.3.6.1.4.1.2773.2.8.1.3.3.1.7	Integer32	read-create	Peak Cell Rate, in cells per second, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: ubrPcr nrtVbr
I32 rsAtmSubIfVccScr	1.3.6.1.4.1.2773.2.8.1.3.3.1.8	Integer32	read-create	Sustained Cell Rate, in cells per second, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: nrtVbr
I32 rsAtmSubIfVccMbs	1.3.6.1.4.1.2773.2.8.1.3.3.1.9	Integer32	read-create	Maximum Burst Size, in cells, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: nrtVbr
rsAtmConformance	1.3.6.1.4.1.2773.2.8.4
rsAtmCompliances	1.3.6.1.4.1.2773.2.8.4.1
rsAtmCompliance	1.3.6.1.4.1.2773.2.8.4.1.1			The compliance statement for entities which implement the Redstone ATM MIB.
rsAtmGroups	1.3.6.1.4.1.2773.2.8.4.2
rsAtmGroup	1.3.6.1.4.1.2773.2.8.4.2.1			A collection of objects providing management of ATM interfaces in a Redstone product.
rsAtmAal5Group	1.3.6.1.4.1.2773.2.8.4.2.2			A collection of objects providing management of AAL5 interfaces in a Redstone product.
rsAtmSubIfGroup	1.3.6.1.4.1.2773.2.8.4.2.3			A collection of objects providing management of ATM subinterfaces in a Redstone product.

RFC description

Redstone ATM (Asynchronous Transfer Mode) MIB for monitoring and managing ATM network interfaces, connections, and quality of service on Redstone network equipment.

Start monitoring Redstone Communications ATM router, ATM WAN edge device (PVC/ILMI configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDSTONE-ATM-MIB

What Is REDSTONE-ATM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description