REDLINE-BS-MIB

All MIBs › REDLINE-BS-MIB

Organization: Redline Communications Inc.

Last Updated: 2005-10-28

Category: Wireless and Radio

Description: Manages Redline Communications WiMAX base station configuration, status, and subscriber connections.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDLINE-BS-MIB?

REDLINE-BS-MIB is a Redline Communications enterprise MIB specific to their WiMAX Base Station (BS) product, covering configuration and status objects applicable only to the base-station role (as opposed to subscriber-station equipment). It exposes IP addressing source, DHCP relay behavior, time synchronization (SNTP/timezone/daylight-saving) settings, radio configuration such as radio type and downlink channel frequency, and configuration-save/persistence controls for both SNMP and radio-frequency (RF) settings. As a monitoring tool it supports configuration/operational-state verification of the base station's networking and RF setup, letting an operator confirm the correct IP addressing mode, DHCP relay operation, time-sync source, and radio channel/frequency plan are in effect, which is important for diagnosing subscriber-connectivity or timing-related WiMAX service issues. It is a self-contained proprietary Redline MIB with no significant dependency on external standard MIBs apparent from the available data. It is deployed on Redline Communications WiMAX base stations used by wireless ISPs and carriers to provide fixed or mobile broadband wireless access to subscriber stations. Engineers can download the REDLINE-BS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDLINE-BS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Redline Communications WiMAX base station

Monitoring Examples

An operator checks redlineBsIpAddressSource and redlineBsDhcpPacketsRelay to confirm whether the base station obtains its IP address via DHCP relay as expected, and reviews redlineBsTimeServerIpAddress, redlineBsTimezone, and redlineBsDayLightSaving to verify the SNTP-based time synchronization is correctly configured (important since WiMAX timing affects frame synchronization). The operator also reviews redlineBsRadioType and redlineBsDownlinkChanFreq to confirm the base station is transmitting on the intended radio channel/frequency, and checks redlineBsSnmpConfigSave/redlineBsSfConfigSave to confirm recent configuration changes have been persisted.

What Can Be Monitored

IP address source/DHCP relay status
time server/SNTP synchronization settings
timezone and daylight-saving configuration
radio type and downlink channel frequency
configuration save/persistence status

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From REDLINE-MIB

redlineSystem

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
redlineBsMib	1.3.6.1.4.1.10728.2.1.2			This MIB module contains object definitions applicable only to Redline Base Station.
redlineBsDhcpObjects	1.3.6.1.4.1.10728.2.1.2.1
INT redlineBsIpAddressSource	1.3.6.1.4.1.10728.2.1.2.1.1	INTEGER	read-write	Setting this variable to 1 causes the Base Station to obatain its ip address from DHCP server.
INT redlineBsDhcpPacketsRelay	1.3.6.1.4.1.10728.2.1.2.1.2	INTEGER	read-write	Setting this variable to 1 causes the Base Station to act as DHCP relay agent for SS. Note: This object can not be set to 'relay' if usage of DHCP server is disabled. An attempt to set the address will fail and return 'resourceUnavailable' error
redlineBsSntpObjects	1.3.6.1.4.1.10728.2.1.2.2
INT redlineBsRefreshTime	1.3.6.1.4.1.10728.2.1.2.2.1	INTEGER	read-write	Setting this variable to 1 causes the Base Station to reconect to time server and synchronize the time
INT redlineBsDayLightSaving	1.3.6.1.4.1.10728.2.1.2.2.2	INTEGER	read-write	This variable indicates if Dalight saving is on.
INT redlineBsTimezone	1.3.6.1.4.1.10728.2.1.2.2.3	INTEGER	read-write	This variable is a time zone set as +/- hours from Greenwich Mean Time (GMT). Note: This object can not be set if usage of DHCP server is enabled. An attempt to set the timezone will fail and return 'resourceUnavailable' error
IPt redlineBsTimeServerIpAddressType	1.3.6.1.4.1.10728.2.1.2.2.4	InetAddressType	read-write	The INET address type of Ip address of time server. IPv4 type supported only.
IP redlineBsTimeServerIpAddress	1.3.6.1.4.1.10728.2.1.2.2.5	InetAddress	read-write	The INET address of time server to whom Bs will communicate using SNTP protocol to obtain the GMT time.
INT redlineBsTimezoneMin	1.3.6.1.4.1.10728.2.1.2.2.6	INTEGER	read-write	This variable contains a minutes part of time zone defined in 'redlineBsTimezone'. Note: This object can not be set if usage of DHCP server is enabled. An attempt to set the timezone will fail and return 'resourceUnavailable' error
redlineBsConfigSaveObjects	1.3.6.1.4.1.10728.2.1.2.3
INT redlineBsSnmpConfigSave	1.3.6.1.4.1.10728.2.1.2.3.1	INTEGER	read-write	Setting this variable to 1 causes SNMP Configuration to be save in flash.
INT redlineBsSfConfigSave	1.3.6.1.4.1.10728.2.1.2.3.2	INTEGER	read-write	Setting this variable to 2 causes Service Flow Configuration to be saved in flash.
redlineBsSystemObjects	1.3.6.1.4.1.10728.2.1.2.4
OCT redlineBsRadioType	1.3.6.1.4.1.10728.2.1.2.4.1	OCTET STRING	read-only	This object indicates the radio type of Redline Bs.
redlineBsRfObjects	1.3.6.1.4.1.10728.2.1.2.5
U32 redlineBsDownlinkChanFreq	1.3.6.1.4.1.10728.2.1.2.5.1	Unsigned32	read-only	Current downlink channel frequency (kHz)
U32 redlineBsUplinkChanFreq	1.3.6.1.4.1.10728.2.1.2.5.2	Unsigned32	read-only	Current uplink channel frequency (kHz)
redlineBsPhyObjects	1.3.6.1.4.1.10728.2.1.2.6
U32 redlineBsChannelSize	1.3.6.1.4.1.10728.2.1.2.6.1	Unsigned32	read-only	Current channel size (Khz).
redlineBsEthObjects	1.3.6.1.4.1.10728.2.1.2.7
INT redlineBsManagementAccess	1.3.6.1.4.1.10728.2.1.2.7.1	INTEGER	read-only	Indicates current management access configuration( either data or mgt port.
INT redlineBsDataPortSettings	1.3.6.1.4.1.10728.2.1.2.7.2	INTEGER	read-only	Indicates current settings of data port.
INT redlineBsMgtPortSettings	1.3.6.1.4.1.10728.2.1.2.7.3	INTEGER	read-only	Indicates current settings of mgt port.
redlineBsVlanObjects	1.3.6.1.4.1.10728.2.1.2.8
INT redlineBsVlanTrafficTagging	1.3.6.1.4.1.10728.2.1.2.8.1	INTEGER	read-only	Indicates that management with VLAN tagged traffic is enabled.
U32 redlineBsVlanId	1.3.6.1.4.1.10728.2.1.2.8.2	Unsigned32	read-only	VLAN identifier used to tag managment traffic.
redlineBsSmcObjects	1.3.6.1.4.1.10728.2.1.2.9
INT redlineBsSmcCurrentOperMode	1.3.6.1.4.1.10728.2.1.2.9.1	INTEGER	read-write	Indicates BS SMC (Secondary Management Channel) operation window. At the beginning of a maintenance window (upgrade, config backup etc), the SMC will be assigned maximum bandwidth to the predetermined fixed rate. At the end of the maintenance window, the maximum bandwidth for the SMC will be reset to its normal rate.
redlineBsPowerSupplyAndCoolingObjects	1.3.6.1.4.1.10728.2.1.2.10
redlineBsPowerSupplyTable	1.3.6.1.4.1.10728.2.1.2.10.1		not-accessible	This table contains identification and status information about base station power supplies. A trap will be generated each time the power supply goes on or off. The traps generation can be enabled/disabled using Redline Trap Activation Table.
redlineBsPowerSupplyEntry	1.3.6.1.4.1.10728.2.1.2.10.1.1		not-accessible	This entry contains status information about base station power supply.
I32 redlineBsPowerSupplyIndex	1.3.6.1.4.1.10728.2.1.2.10.1.1.1	Integer32	not-accessible	The index of the BS power supply table.
STR redlineBsPowerSupplyName	1.3.6.1.4.1.10728.2.1.2.10.1.1.2	DisplayString	read-only	Textual identification of base station power supply.
INT redlineBsPowerSupplyType	1.3.6.1.4.1.10728.2.1.2.10.1.1.3	INTEGER	read-only	The power supply type.
INT redlineBsPowerSupplyStatus	1.3.6.1.4.1.10728.2.1.2.10.1.1.4	INTEGER	read-only	Indicates if the power supply is on/off.
redlineBsTemperatureTable	1.3.6.1.4.1.10728.2.1.2.10.2		not-accessible	This table contains information about current temperature of base station hardware units.
redlineBsTemperatureEntry	1.3.6.1.4.1.10728.2.1.2.10.2.1		not-accessible	This entry contains temperature information about single base station hardware unit.
I32 redlineBsUnitIndex	1.3.6.1.4.1.10728.2.1.2.10.2.1.1	Integer32	not-accessible	The index of the BS current temperature table.
STR redlineBsUnitName	1.3.6.1.4.1.10728.2.1.2.10.2.1.2	DisplayString	read-only	The base station hardware unit name.
INT redlineBsUnitType	1.3.6.1.4.1.10728.2.1.2.10.2.1.3	INTEGER	read-only	The base station hardware unit type.
I32 redlineBsCurrTemperature	1.3.6.1.4.1.10728.2.1.2.10.2.1.4	Integer32	read-only	Indicates the current temperature of base station hardware unit in Celsius.
redlineBsTempThresholdTable	1.3.6.1.4.1.10728.2.1.2.10.3		not-accessible	This table contains various temperature threshold which are used to trigger traps to alarm network manager about unit mulfunction. The table is indexed by 'redlineBsUnitIndex' and 'redlineBsTempThresholdIndex' objects. Some of the traps require clearing after the temperature is going back to normal. The traps can be enabled/disabled using Redline Trap Activation table.
redlineBsTempThresholdEntry	1.3.6.1.4.1.10728.2.1.2.10.3.1		not-accessible	This entry contains single base station hardware unit temperarure threshold information.
I32 redlineBsTempThresholdIndex	1.3.6.1.4.1.10728.2.1.2.10.3.1.1	Integer32	not-accessible	The index of the temperature threshold table.
I32 redlineBsTempTrapThreshold	1.3.6.1.4.1.10728.2.1.2.10.3.1.2	Integer32	read-only	Indicates the temperature threshold value which will be used to trigger a trap.
I32 redlineBsTempTrapClrThreshold	1.3.6.1.4.1.10728.2.1.2.10.3.1.3	Integer32	read-only	Indicates the temperature threshold value which will be used to clear a previosly generated trap.
STR redlineBsTempThresholdName	1.3.6.1.4.1.10728.2.1.2.10.3.1.4	DisplayString	read-only	Textual identification of temperature threshold.
INT redlineBsTemperatureTrapTrigger	1.3.6.1.4.1.10728.2.1.2.10.3.1.5	INTEGER	read-only	Indicates if temperature traversal in upper or lower value direction is causing the trap.
redlineBsFanTable	1.3.6.1.4.1.10728.2.1.2.10.4		not-accessible	This table contains name and status information about base station cooling fans. Up to 3 entries are supported.
redlineBsFanEntry	1.3.6.1.4.1.10728.2.1.2.10.4.1		not-accessible	This entry contains information about single cooling fan.
I32 redlineBsFanIndex	1.3.6.1.4.1.10728.2.1.2.10.4.1.1	Integer32	not-accessible	The index of the colling fans table.
STR redlineBsFanName	1.3.6.1.4.1.10728.2.1.2.10.4.1.2	DisplayString	read-only	Textual identification of base station fan.
INT redlineBsFanStatus	1.3.6.1.4.1.10728.2.1.2.10.4.1.3	INTEGER	read-only	Indicates the base station fan is on/off.
redlineBsNotificationObjects	1.3.6.1.4.1.10728.2.1.2.11
redlineBsTrapDefinitions	1.3.6.1.4.1.10728.2.1.2.11.0
NTF redlineBsPowerSupplyStatusTrap	1.3.6.1.4.1.10728.2.1.2.11.0.1			Event that reports base station power supply status change (on/off).
NTF redlineBsTempThresholdTrap	1.3.6.1.4.1.10728.2.1.2.11.0.2			Event that reports SW Upgrade progress and status changes.
redlineBsTrapMibObjects	1.3.6.1.4.1.10728.2.1.2.11.1
INT redlineBsTrapType	1.3.6.1.4.1.10728.2.1.2.11.1.1	INTEGER	accessible-for-notify	Indicates if the trap is for alarm condition or for its clearing.
I32 redlineBsTrapPowerSupplyIndex	1.3.6.1.4.1.10728.2.1.2.11.1.2	Integer32	accessible-for-notify	The index in the table representing BS power supply triggering the trap.
I32 redlineBsTrapUnitIndex	1.3.6.1.4.1.10728.2.1.2.11.1.3	Integer32	accessible-for-notify	The index of temperature table representing BS unit triggering the trap.
I32 redlineBsTrapTempThresholdIndex	1.3.6.1.4.1.10728.2.1.2.11.1.4	Integer32	accessible-for-notify	The index of the temperature threshold table representing the temperature threshold which passing is triggering the trap.
redlineBsConformance	1.3.6.1.4.1.10728.2.1.2.12
redlineBsGroups	1.3.6.1.4.1.10728.2.1.2.12.1
redlineBsDhcpGroup	1.3.6.1.4.1.10728.2.1.2.12.1.1			Dhcp objects.
redlineBsSntpGroup	1.3.6.1.4.1.10728.2.1.2.12.1.2			Sntp objects.
redlineBsConfigSaveGroup	1.3.6.1.4.1.10728.2.1.2.12.1.3			Config save objects.
redlineBsSystemGroup	1.3.6.1.4.1.10728.2.1.2.12.1.4			Config save objects.
redlineBsRfGroup	1.3.6.1.4.1.10728.2.1.2.12.1.5			Config save objects.
redlineBsPhyGroup	1.3.6.1.4.1.10728.2.1.2.12.1.6			Config save objects.
redlineBsEthGroup	1.3.6.1.4.1.10728.2.1.2.12.1.7			Ethernet interface objects.
redlineBsVlanGroup	1.3.6.1.4.1.10728.2.1.2.12.1.8			Vlan objects.
redlineBsSmcGroup	1.3.6.1.4.1.10728.2.1.2.12.1.9			Smc objects.
redlineBsPowerSupplyAndCoolingGroup	1.3.6.1.4.1.10728.2.1.2.12.1.10			Power supply, temperature and fans objects.
redlineBsNotificationGroup	1.3.6.1.4.1.10728.2.1.2.12.1.11
redlineBsCompls	1.3.6.1.4.1.10728.2.1.2.12.2
redlineBsCompliance	1.3.6.1.4.1.10728.2.1.2.12.2.1			The compliance statement for SNMP entities that implement this MIB module.

RFC description

Configures DHCP, NTP synchronization, and network settings for Redline wireless base stations.

Start monitoring Redline Communications WiMAX base station (IP/DHCP/time-sync/radio-channel configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDLINE-BS-MIB

What Is REDLINE-BS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description