REDLINE-AN80I-MIB

All MIBs › REDLINE-AN80I-MIB

Organization: Redline Communications Inc.

Last Updated: 2005-11-29

Category: Wireless and Radio

Description: Provides system-level management objects for Redline Communications AN80i point-to-point microwave backhaul equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDLINE-AN80I-MIB?

REDLINE-AN80I-MIB is a Redline Communications enterprise MIB for the AN80i point-to-point microwave backhaul radio, covering system-level configuration and operational objects specific to that hardware. It exposes objects for hardware/radio identification (hardware type, radio type), software licensing (options keys), configuration management (save/activate configuration), and RF operating parameters such as antenna alignment mode and current transmit power. Its monitoring value is strongly hardware/software-status oriented: an operator can check the current radio type and hardware type installed, confirm which software feature license keys are active, track transmit power levels for link-budget health, and monitor antenna alignment mode during installation or realignment. It is a vendor-specific MIB not directly layered on a common microwave/backhaul IETF standard, reflecting Redline's proprietary AN80i platform. It is deployed on Redline AN80i point-to-point microwave links used for wireless backhaul in carrier, enterprise, or rural broadband networks. Engineers can download the REDLINE-AN80I-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDLINE-AN80I-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Redline AN80i point-to-point microwave backhaul radios

Monitoring Examples

An operator would check an80iHardwareType and an80iRadioType to confirm the installed radio hardware, and an80iCurrTxPower to verify the transmit power is within expected range for the link budget; a drop in an80iCurrTxPower or an unexpected antenna alignment mode reported via an80iAntennaAllignmentMode could explain a degraded backhaul link. an80iOptionsKeyTable/an80iOptionsKeyEntry, keyed by an80iOptionsKeyId, lets an admin verify an80iOptionsKey/an80iOptionsKeyStatus to confirm licensed features are active. an80iSaveConfig and an80iActivateConfig are used to persist and apply configuration changes, important to check after a maintenance change to confirm it took effect.

What Can Be Monitored

radio/hardware type identification
current transmit power
antenna alignment mode/status
software feature license (options key) status
configuration save/activate state

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From REDLINE-MIB

redlineSystem

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
redlineAn80iMib	1.3.6.1.4.1.10728.2.1.3			This MIB module contains object definitions applicable only to Redline AN80i switched device.
redlineAn80iTrapDefinitions	1.3.6.1.4.1.10728.2.1.3.0
NTF an80iPswdChangeFailTrap	1.3.6.1.4.1.10728.2.1.3.0.1			An event to report the failure of a password change.
NTF an80iFirmwareConfigFailTrap	1.3.6.1.4.1.10728.2.1.3.0.2			An event to report the failure of a firmware config.
NTF an80iEepromCorruptedTrap	1.3.6.1.4.1.10728.2.1.3.0.3			An event to report the corruption of the EEPROM.
NTF an80iHardwareFailTrap	1.3.6.1.4.1.10728.2.1.3.0.4			An event to report the hardware failure.
NTF an80iSaveConfigTrap	1.3.6.1.4.1.10728.2.1.3.0.5			An event to report the saving of configuration
NTF an80iDFSEventTrap	1.3.6.1.4.1.10728.2.1.3.0.6			An event to report the radar frequency detection
NTF an80iIdChangedTrap	1.3.6.1.4.1.10728.2.1.3.0.7			Event that reports the modification in the configuration of an ID.
NTF an80iSWUpgradeFailed	1.3.6.1.4.1.10728.2.1.3.0.8			Event that reports the failure of a software upgrade opration.
NTF an80iSWUpgradeSuccess	1.3.6.1.4.1.10728.2.1.3.0.9			Event that reports the success of a software upgrade opration.
redlineAn80iPtpPmpObjects	1.3.6.1.4.1.10728.2.1.3.1
redlineAn80iSystemObjects	1.3.6.1.4.1.10728.2.1.3.1.1
an80iOptionsKeyTable	1.3.6.1.4.1.10728.2.1.3.1.1.1		not-accessible	This table contains options key information. The maximum number of configured options key is 2.
an80iOptionsKeyEntry	1.3.6.1.4.1.10728.2.1.3.1.1.1.1		not-accessible	This table provides one row for each option key defined in the AN80i system
INT an80iOptionsKeyId	1.3.6.1.4.1.10728.2.1.3.1.1.1.1.1	INTEGER	not-accessible	The Options Key Identifier.
STR an80iOptionsKey	1.3.6.1.4.1.10728.2.1.3.1.1.1.1.2	DisplayString	read-create	The options key value.
ROW an80iOptionsKeyStatus	1.3.6.1.4.1.10728.2.1.3.1.1.1.1.3	RowStatus	read-create	This object is used to ctivate and deactivate rows in the an80iOptionsKeyTable table. There will be only two rows in the table and only one will be active. When one row is active the other one will be notInService. The row can not be created or deleted
I32 an80iHardwareType	1.3.6.1.4.1.10728.2.1.3.1.1.2	Integer32	read-only	The type/version/revision of the hardware.
I32 an80iRadioType	1.3.6.1.4.1.10728.2.1.3.1.1.3	Integer32	read-only	The radio type.
INT an80iSaveConfig	1.3.6.1.4.1.10728.2.1.3.1.1.4	INTEGER	read-write	This object will save the configuration in the nonvolatile memory and will activate the new configuration.
INT an80iActivateConfig	1.3.6.1.4.1.10728.2.1.3.1.1.5	INTEGER	read-write	This object will activate the new configuration without saving it in the nonvolatile memory. If after this event it will elapse more than 5 minutes and no save configuration occurs, then system will restart with the configuration from the nonvolatile memory.
redlineAn80iWirelesObjects	1.3.6.1.4.1.10728.2.1.3.1.2
INT an80iAntennaAllignmentMode	1.3.6.1.4.1.10728.2.1.3.1.2.1	INTEGER	read-write	Specifies if the antenna alignment buzzer is enabled or not. In the future, new alignment methods may be added.
INT an80iCurrTxPower	1.3.6.1.4.1.10728.2.1.3.1.2.2	INTEGER	read-only	The actual Tx Power of the AN-80i Node.
INT an80iChannelAutoScan	1.3.6.1.4.1.10728.2.1.3.1.2.3	INTEGER	read-write	Specifies if the frequency auto-scanning feature is enabled
I32 an80iCurrFrequency	1.3.6.1.4.1.10728.2.1.3.1.2.4	Integer32	read-only	The central frequency on which the equipment operates. If the auto-scanning feature is enabled then this may be different than the an80iOPeratingFrequency. [KHz]
I32 an80iOPeratingFrequency	1.3.6.1.4.1.10728.2.1.3.1.2.5	Integer32	read-write	Specifies the operating frequency of the system [KHz].
INT an80iMaxTxPower	1.3.6.1.4.1.10728.2.1.3.1.2.6	INTEGER	read-write	The Tx Power of the AN-80i. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this parameter needs to be changed, please contact the Redline support team.
INT an80iSystemMode	1.3.6.1.4.1.10728.2.1.3.1.2.7	INTEGER	read-write	1 = PMP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master
I32 an80iRFStatusCode	1.3.6.1.4.1.10728.2.1.3.1.2.8	Integer32	read-only	Specifies the Error Code for the RF Interface.
INT an80iDFSAction	1.3.6.1.4.1.10728.2.1.3.1.2.9	INTEGER	read-write	Action taken when a radar is detected on the same frequency.
I32 an80iAntennaGain	1.3.6.1.4.1.10728.2.1.3.1.2.10	Integer32	read-write	The gain of the antenna attached to the system.
I32 an80iActiveRFLinks	1.3.6.1.4.1.10728.2.1.3.1.2.11	Integer32	read-only	The actual number of provisioned links.
INT an80iAtpControl	1.3.6.1.4.1.10728.2.1.3.1.2.12	INTEGER	read-write	Enable/disable the automatic Tx power control.
INT an80iTurboModeControl	1.3.6.1.4.1.10728.2.1.3.1.2.13	INTEGER	read-write	Enable/disable the turbo mode. In this mode the system uses a 40MHz channel (20 MHz in normal mode).
INT an80iChannelWidth	1.3.6.1.4.1.10728.2.1.3.1.2.14	INTEGER	read-write	The width of the channel.
redlineAn80iEthernetObjects	1.3.6.1.4.1.10728.2.1.3.1.3
INT an80iEtherPortConn	1.3.6.1.4.1.10728.2.1.3.1.3.1	INTEGER	read-write	Specifies Ethernet port connection auto(1), mdi(2) or mdix(3)
INT an80iEtherPortMode	1.3.6.1.4.1.10728.2.1.3.1.3.2	INTEGER	read-write	The attribute specifies the Ethernet LED status of the AN80i.
INT an80iFlowControl	1.3.6.1.4.1.10728.2.1.3.1.3.3	INTEGER	read-write	This object specifies if flow control is enabled or not.
INT an80iLowLatencyMode	1.3.6.1.4.1.10728.2.1.3.1.3.4	INTEGER	read-write	This object specifies if prioritized low latency mode is enabled or not.
INT an80iEthernetFollowsWireless	1.3.6.1.4.1.10728.2.1.3.1.3.5	INTEGER	read-write	This object specifies if the Ethernet follows wireless mode is enabled or not.
INT an80iEthernetFollowsWirelessTimeout	1.3.6.1.4.1.10728.2.1.3.1.3.6	INTEGER	read-write	This object specifies if the timeout (seconds) for the Ethernet follows wireless mode (0=infinite).
redlineAn80iManagObjects	1.3.6.1.4.1.10728.2.1.3.1.4
INT an80iHttpAccess	1.3.6.1.4.1.10728.2.1.3.1.4.1	INTEGER	read-write	This object specifies if Http Access is enabled or not.
INT an80iTelnetAccess	1.3.6.1.4.1.10728.2.1.3.1.4.2	INTEGER	read-write	This object specifies if Telnet Access is enabled or not.
INE an80iTelnetPort	1.3.6.1.4.1.10728.2.1.3.1.4.3	InetPortNumber	read-write	This object specifies the Telnet port number.
redlineAn80iSWUpgradeObjects	1.3.6.1.4.1.10728.2.1.3.1.5
IPt an80iSwDownloadTftpAddressType	1.3.6.1.4.1.10728.2.1.3.1.5.1	InetAddressType	read-write	The INET address type of the software upgrade TFTP server. IPv4 type supported only.
IP an80iSwDownloadTftpAddress	1.3.6.1.4.1.10728.2.1.3.1.5.2	InetAddress	read-write	The INET address of the TFTP server.
STR an80iSwDownloadTftpFile	1.3.6.1.4.1.10728.2.1.3.1.5.3	DisplayString	read-write	The image file name as required by the TFTP server.
INT an80iSwDownloadStatus	1.3.6.1.4.1.10728.2.1.3.1.5.4	INTEGER	read-only	The status of the current software download.
INT an80iSwDownloadControl	1.3.6.1.4.1.10728.2.1.3.1.5.5	INTEGER	read-write	Trigger software upgrade
redlineAn80iPmpObjects	1.3.6.1.4.1.10728.2.1.3.2
redlineAn80iPmpWirelesObjects	1.3.6.1.4.1.10728.2.1.3.2.1
INT an80iRegistrationPeriod	1.3.6.1.4.1.10728.2.1.3.2.1.1	INTEGER	read-write	Number of frames between two consecutive registration periods.
INT an80iMaximumDistance	1.3.6.1.4.1.10728.2.1.3.2.1.2	INTEGER	read-write	Maximum distance in km between the sector controller and one subscriber station.
I32 an80iRegisteredStations	1.3.6.1.4.1.10728.2.1.3.2.1.3	Integer32	read-only	The number of registered stations on the sector controller.
I32 an80iRegisteredConnections	1.3.6.1.4.1.10728.2.1.3.2.1.4	Integer32	read-only	The number of registered connections on the sector controller.
INT an80iMaxId	1.3.6.1.4.1.10728.2.1.3.2.1.5	INTEGER	read-only	The maximum number of ID used to identify links, connections and groups
I32 an80iNextAvailId	1.3.6.1.4.1.10728.2.1.3.2.1.6	Integer32	read-only	The next available ID from the ID pool which is not grater then that defined in 'an80iMaxId'
I32 an80iLastModifId	1.3.6.1.4.1.10728.2.1.3.2.1.7	Integer32	read-only	The last modified ID from the ID pool which is not grater then that defined in 'an80iMaxId'
INT an80iSaveIdConfiguration	1.3.6.1.4.1.10728.2.1.3.2.1.8	INTEGER	read-write	Save the ID table in the flash memory
redlineAn80iPtpObjects	1.3.6.1.4.1.10728.2.1.3.3
redlineAn80iPtpSystemObjects	1.3.6.1.4.1.10728.2.1.3.3.1
INT an80iResetStatistics	1.3.6.1.4.1.10728.2.1.3.3.1.1	INTEGER	read-write	This object resets wireless and Ethernet counters
redlineAn80iConformance	1.3.6.1.4.1.10728.2.1.3.5
redlineAn80iGroups	1.3.6.1.4.1.10728.2.1.3.5.1
redlineAn80iPtpPmpGroup	1.3.6.1.4.1.10728.2.1.3.5.1.1			AN80i PTP/PMP objects.
redlineAn80iPmpGroup	1.3.6.1.4.1.10728.2.1.3.5.1.2			AN80i PMP objects.
redlineAn80iPtpGroup	1.3.6.1.4.1.10728.2.1.3.5.1.3			AN80i PTP objects.
redlineAn80iNotificationGroup	1.3.6.1.4.1.10728.2.1.3.5.1.4			The notifications which indicate specific events within the AN80i unit.
redlineAn80iCompls	1.3.6.1.4.1.10728.2.1.3.5.2
redlineAn80iCompliance	1.3.6.1.4.1.10728.2.1.3.5.2.1			The compliance statement for AN80i entities that implement this MIB module.

RFC description

SNMP MIB for Redline AN80i point-to-point wireless broadband systems, enabling remote management and performance monitoring of wireless links.

Start monitoring Redline AN80i point-to-point microwave backhaul radio (hardware/software/RF configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDLINE-AN80I-MIB

What Is REDLINE-AN80I-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description