All MIBs › RBN-L2VPN-MIB
Organization: Ericsson AB
Last Updated: 2011-01-19
Category: Pseudowire and L2VPN, Vendor: Ericsson
Description: Manages Layer 2 VPN service instances, pseudowires, and attachment circuits on Ericsson SmartEdge BRAS platforms.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is RBN-L2VPN-MIB?
RBN-L2VPN-MIB is a Redback Networks (Ericsson SmartEdge) enterprise MIB for managing Layer 2 VPN services, including MPLS pseudowires and static cross-connects, on SmartEdge BRAS/router platforms. It defines objects for static pseudowire configuration, labels, peer addresses, circuit handles, cross-connect flags, and interface bindings, plus notifications for L2VPN state changes. Its monitoring value centers on pseudowire operational status: whether an input circuit is up, label and peer-address consistency, and cross-connect flag state, which together reveal a pseudowire that has gone down or is misconfigured. It builds on MPLS and pseudowire signaling conventions, similar in spirit to the IETF PW-MIB, while remaining a Redback/Ericsson proprietary extension. It is deployed on Ericsson SmartEdge routers, where RBN-L2VPN-MIB SNMP monitoring supports carrier Layer 2 VPN/pseudowire services.
IPNetwork Monitor allows you to monitor SNMP objects defined in RBN-L2VPN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ericsson SmartEdge routers/BRAS platforms
Monitoring Examples
An operator can poll rbnMplsL2VpnStaticTable/rbnMplsL2VpnStaticEntry for a given pseudowire to check rbnMplsL2VpnStaticInputCctUp and rbnMplsL2VpnStaticPeerAddr, confirming the pseudowire to a specific peer is active. If rbnMplsL2VpnStaticInputCctUp flips to down or rbnMplsL2VpnStaticXcFlags shows an inconsistent cross-connect state, that flags a pseudowire failure needing remediation, and rbnMplsL2VpnMIBNotifications would typically fire a corresponding trap.
What Can Be Monitored
- pseudowire operational status
- pseudowire peer address and label
- cross-connect flag state
- L2VPN static configuration
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType | |
| InetPortNumber |
From RBN-SMI
| rbnMgmt | OBJECT-IDENTITY |
From RBN-TC
| RbnCircuitHandle |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rbnL2VpnMIB | 1.3.6.1.4.1.2352.2.39 | This management information base displays Layer 2 Virtual Private Networks(VPN) / Pesudowires(PWs) information. | ||
| rbnMplsL2VpnMIBNotifications | 1.3.6.1.4.1.2352.2.39.0 | |||
| NTF rbnMplsL2VpnLdpPwStateChange | 1.3.6.1.4.1.2352.2.39.0.1 | This notification is generated when PW state transitions operationally to UP/DOWN/STANDBY. | ||
| rbnL2VpnMIBObjects | 1.3.6.1.4.1.2352.2.39.1 | |||
| rbnL2VpnStaticTable | 1.3.6.1.4.1.2352.2.39.1.1 | not-accessible | This table contains objects which identify static Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured. | |
| rbnL2VpnStaticEntry | 1.3.6.1.4.1.2352.2.39.1.1.1 | not-accessible | A conceptual row in the rbnL2VpnStaticTable. | |
| IP rbnL2VpnStaticPeerAddr | 1.3.6.1.4.1.2352.2.39.1.1.1.1 | IpAddress | not-accessible | This object indicates the ip address of the VPN peer. |
| U32 rbnL2VpnStaticVpnLabel | 1.3.6.1.4.1.2352.2.39.1.1.1.2 | Unsigned32 | not-accessible | This object indicates the unique value assigned to a particular static VPN circuit. |
| RBN rbnL2VpnStaticCctHandle | 1.3.6.1.4.1.2352.2.39.1.1.1.3 | RbnCircuitHandle | read-only | This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit. |
| RBN rbnL2VpnStaticVpnCctHandle | 1.3.6.1.4.1.2352.2.39.1.1.1.4 | RbnCircuitHandle | read-only | This object indicates the internal representation of VPN pseudo circuit. |
| U32 rbnL2VpnStaticExpBits | 1.3.6.1.4.1.2352.2.39.1.1.1.5 | Unsigned32 | read-only | This object indicates the number of exp bits configured for this VPN circuit. |
| T/F rbnL2VpnStaticInputCctUp | 1.3.6.1.4.1.2352.2.39.1.1.1.6 | TruthValue | read-only | This object indicates the status of the VPN input circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected. |
| RBN rbnL2VpnStaticXcFlags | 1.3.6.1.4.1.2352.2.39.1.1.1.7 | RbnVpnXcFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| NUM rbnL2VpnStaticIfIndexOrZero | 1.3.6.1.4.1.2352.2.39.1.1.1.8 | InterfaceIndexOrZero | read-only | This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry. |
| rbnL2VpnLdpTable | 1.3.6.1.4.1.2352.2.39.1.2 | not-accessible | This table contains objects which identify Layer Distribution Protocol Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured. | |
| rbnL2VpnLdpEntry | 1.3.6.1.4.1.2352.2.39.1.2.1 | not-accessible | A conceptual row in the rbnL2VpnStaticTable. | |
| IP rbnL2VpnLdpPeerAddr | 1.3.6.1.4.1.2352.2.39.1.2.1.1 | IpAddress | not-accessible | This object indicates the ip address if the VPN peer. |
| I32 rbnL2VpnLdpVcId | 1.3.6.1.4.1.2352.2.39.1.2.1.2 | Integer32 | not-accessible | This object indicates the unique virtual VPN circuit id assigned to this circuit. |
| RBN rbnL2VpnLdpCctHandle | 1.3.6.1.4.1.2352.2.39.1.2.1.3 | RbnCircuitHandle | read-only | This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit. |
| RBN rbnL2VpnLdpVpnCctHandle | 1.3.6.1.4.1.2352.2.39.1.2.1.4 | RbnCircuitHandle | read-only | This object indicates the internal representation of the VPN pseudo circuit. |
| U32 rbnL2VpnLdpInLabel | 1.3.6.1.4.1.2352.2.39.1.2.1.5 | Unsigned32 | read-only | This object indicates the value setup in the local configuration to identify this VPN circuit. |
| U32 rbnL2VpnLdpVpnLabel | 1.3.6.1.4.1.2352.2.39.1.2.1.6 | Unsigned32 | read-only | This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the local manager. |
| U32 rbnL2VpnLdpRemGrpId | 1.3.6.1.4.1.2352.2.39.1.2.1.7 | Unsigned32 | read-only | This object indicates the remote group of which this VPN circuit is a part. |
| STR rbnL2VpnLdpLocEncap | 1.3.6.1.4.1.2352.2.39.1.2.1.8 | SnmpAdminString | read-only | This object indicates the local encaps type associated with this VPN circuit. |
| STR rbnL2VpnLdpRemEncap | 1.3.6.1.4.1.2352.2.39.1.2.1.9 | SnmpAdminString | read-only | This object indicates the remote encaps type associated with this VPN circuit. |
| RBN rbnL2VpnLdpLocVcType | 1.3.6.1.4.1.2352.2.39.1.2.1.10 | RbnVpnVcType | read-only | This object indicates the type of virtual circuit on the local system. |
| RBN rbnL2VpnLdpRemVcType | 1.3.6.1.4.1.2352.2.39.1.2.1.11 | RbnVpnVcType | read-only | This object indicates the type of virtual circuit on the remote system. |
| U32 rbnL2VpnLdpLocMtu | 1.3.6.1.4.1.2352.2.39.1.2.1.12 | Unsigned32 | read-only | This object indicates the maximum transmission unit of the local VPN circuit. |
| U32 rbnL2VpnLdpRemMtu | 1.3.6.1.4.1.2352.2.39.1.2.1.13 | Unsigned32 | read-only | This object indicates the maximum transmission unit of the remote connection. |
| T/F rbnL2VpnLdpXcCctUp | 1.3.6.1.4.1.2352.2.39.1.2.1.14 | TruthValue | read-only | This object indicates the status of the VPN cross connect circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected. |
| U32 rbnL2VpnLdpExpBits | 1.3.6.1.4.1.2352.2.39.1.2.1.15 | Unsigned32 | read-only | This object indicates the number of exp bits configured for this VPN circuit. |
| T/F rbnL2VpnLdpInputCctUp | 1.3.6.1.4.1.2352.2.39.1.2.1.16 | TruthValue | read-only | This object indicates the status of the VPN input circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected. |
| RBN rbnL2VpnLdpXcFlags | 1.3.6.1.4.1.2352.2.39.1.2.1.17 | RbnVpnXcFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| NUM rbnL2VpnLdpIfIndexOrZero | 1.3.6.1.4.1.2352.2.39.1.2.1.18 | InterfaceIndexOrZero | read-only | This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry. |
| rbnL2VpnMIBConformance | 1.3.6.1.4.1.2352.2.39.2 | |||
| rbnL2VpnMIBGroups | 1.3.6.1.4.1.2352.2.39.2.1 | |||
| rbnL2VpnStaticGroup | 1.3.6.1.4.1.2352.2.39.2.1.1 | A collection of objects providing information about the status of static L2 VPN connections. | ||
| rbnL2VpnLdpGroup | 1.3.6.1.4.1.2352.2.39.2.1.2 | A collection of objects providing information about the status of L2 VPN connections using Label Detection Protocol. | ||
| rbnMplsL2VpnPwScalarGroup | 1.3.6.1.4.1.2352.2.39.2.1.3 | Collection of scalar objects required for L2VPN PW management | ||
| rbnMplsL2VpnStaticPwGroup | 1.3.6.1.4.1.2352.2.39.2.1.4 | A collection of objects providing information about the status of static L2 VPN Pesudowires. | ||
| rbnMplsL2VpnLdpPwGroup | 1.3.6.1.4.1.2352.2.39.2.1.5 | A collection of objects providing information about the status of L2 VPN Pesudowires using Label Detection Protocol. | ||
| rbnMplsL2VpnPwNotificationGroup | 1.3.6.1.4.1.2352.2.39.2.1.6 | Objects required for L2VPN PW notifications. | ||
| rbnUdpL2VpnStaticPwGroup | 1.3.6.1.4.1.2352.2.39.2.1.7 | A collection of objects providing information about the status of static L2 VPN Pesudowires. | ||
| rbnL2VpnMIBCompliances | 1.3.6.1.4.1.2352.2.39.2.2 | |||
| rbnL2VpnMIBCompliance | 1.3.6.1.4.1.2352.2.39.2.2.1 | The compliance statement for the L2VPN MIB. | ||
| rbnMplsL2VpnPwMIBCompliance | 1.3.6.1.4.1.2352.2.39.2.2.2 | The compliance statement for the L2VPN MIB. | ||
| rbnUdpL2VpnPwMIBCompliance | 1.3.6.1.4.1.2352.2.39.2.2.3 | The compliance statement for the L2VPN MIB. | ||
| rbnMplsL2VpnMIBGroups | 1.3.6.1.4.1.2352.2.39.2.3 | |||
| rbnMplsL2VpnStaticGroup | 1.3.6.1.4.1.2352.2.39.2.3.1 | A collection of objects providing information about the status of static L2 VPN connections. | ||
| rbnMplsL2VpnLdpGroup | 1.3.6.1.4.1.2352.2.39.2.3.2 | A collection of objects providing information about the status of L2 VPN connections using Label Detection Protocol. | ||
| rbnMplsL2VpnMIBCompliances | 1.3.6.1.4.1.2352.2.39.2.4 | |||
| rbnMplsL2VpnMIBCompliance | 1.3.6.1.4.1.2352.2.39.2.4.1 | The compliance statement for the L2VPN MIB. | ||
| rbnMplsL2VpnMIBObjects | 1.3.6.1.4.1.2352.2.39.3 | |||
| rbnMplsL2VpnStaticTable | 1.3.6.1.4.1.2352.2.39.3.3 | not-accessible | This table contains objects which identify static Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured. | |
| rbnMplsL2VpnStaticEntry | 1.3.6.1.4.1.2352.2.39.3.3.1 | not-accessible | A conceptual row in the rbnMplsL2VpnStaticTable. | |
| U32 rbnMplsL2VpnStaticInLabel | 1.3.6.1.4.1.2352.2.39.3.3.1.1 | Unsigned32 | not-accessible | This object indicates the unique value assigned to a particular static VPN circuit. |
| IP rbnMplsL2VpnStaticPeerAddr | 1.3.6.1.4.1.2352.2.39.3.3.1.2 | IpAddress | not-accessible | This object indicates the ip address of the VPN peer. |
| RBN rbnMplsL2VpnStaticCctHandle | 1.3.6.1.4.1.2352.2.39.3.3.1.3 | RbnCircuitHandle | read-only | This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit. |
| RBN rbnMplsL2VpnStaticVpnCctHandle | 1.3.6.1.4.1.2352.2.39.3.3.1.4 | RbnCircuitHandle | read-only | This object indicates the internal representation of VPN pseudo circuit. |
| U32 rbnMplsL2VpnStaticExpBits | 1.3.6.1.4.1.2352.2.39.3.3.1.5 | Unsigned32 | read-only | This object indicates the number of exp bits configured for this VPN circuit. |
| T/F rbnMplsL2VpnStaticInputCctUp | 1.3.6.1.4.1.2352.2.39.3.3.1.6 | TruthValue | read-only | This object indicates the status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is connected with its remote site. A value of false indicates that the remote site is not presently connected. |
| RBN rbnMplsL2VpnStaticXcFlags | 1.3.6.1.4.1.2352.2.39.3.3.1.7 | RbnVpnXcFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| NUM rbnMplsL2VpnStaticIfIndexOrZero | 1.3.6.1.4.1.2352.2.39.3.3.1.8 | InterfaceIndexOrZero | read-only | This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry. |
| RBN rbnMplsL2VpnStaticPwFlags | 1.3.6.1.4.1.2352.2.39.3.3.1.9 | RbnVpnPwFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| RBN rbnMplsL2VpnStaticPwState | 1.3.6.1.4.1.2352.2.39.3.3.1.10 | RbnVpnPwStateType | read-only | This object indicates the status of the VPN input circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active(i.e. up) |
| U32 rbnMplsL2VpnStaticVpnLabel | 1.3.6.1.4.1.2352.2.39.3.3.1.11 | Unsigned32 | read-only | This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the label manager. |
| rbnMplsL2VpnLdpTable | 1.3.6.1.4.1.2352.2.39.3.4 | not-accessible | This table contains objects which identify Layer Distribution Protocol Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured. | |
| rbnMplsL2VpnLdpEntry | 1.3.6.1.4.1.2352.2.39.3.4.1 | not-accessible | A conceptual row in the rbnMplsL2VpnLdpTable. | |
| U32 rbnMplsL2VpnLdpVcId | 1.3.6.1.4.1.2352.2.39.3.4.1.1 | Unsigned32 | not-accessible | This object indicates the unique virtual VPN circuit id assigned to this circuit. |
| IP rbnMplsL2VpnLdpPeerAddr | 1.3.6.1.4.1.2352.2.39.3.4.1.2 | IpAddress | not-accessible | This object indicates the ip address if the VPN peer. |
| RBN rbnMplsL2VpnLdpCctHandle | 1.3.6.1.4.1.2352.2.39.3.4.1.3 | RbnCircuitHandle | read-only | This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit. |
| RBN rbnMplsL2VpnLdpVpnCctHandle | 1.3.6.1.4.1.2352.2.39.3.4.1.4 | RbnCircuitHandle | read-only | This object indicates the internal representation of the VPN pseudo circuit. |
| U32 rbnMplsL2VpnLdpInLabel | 1.3.6.1.4.1.2352.2.39.3.4.1.5 | Unsigned32 | read-only | This object indicates the value setup in the local configuration to identify this VPN circuit. |
| U32 rbnMplsL2VpnLdpVpnLabel | 1.3.6.1.4.1.2352.2.39.3.4.1.6 | Unsigned32 | read-only | This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the local manager. |
| U32 rbnMplsL2VpnLdpRemGrpId | 1.3.6.1.4.1.2352.2.39.3.4.1.7 | Unsigned32 | read-only | This object indicates the remote group of which this VPN circuit is a part. |
| STR rbnMplsL2VpnLdpLocEncap | 1.3.6.1.4.1.2352.2.39.3.4.1.8 | SnmpAdminString | read-only | This object indicates the local encaps type associated with this VPN circuit. |
| STR rbnMplsL2VpnLdpRemEncap | 1.3.6.1.4.1.2352.2.39.3.4.1.9 | SnmpAdminString | read-only | This object indicates the remote encaps type associated with this VPN circuit. |
| RBN rbnMplsL2VpnLdpLocVcType | 1.3.6.1.4.1.2352.2.39.3.4.1.10 | RbnVpnVcType | read-only | This object indicates the type of virtual circuit on the local system. |
| RBN rbnMplsL2VpnLdpRemVcType | 1.3.6.1.4.1.2352.2.39.3.4.1.11 | RbnVpnVcType | read-only | This object indicates the type of virtual circuit on the remote system. |
| U32 rbnMplsL2VpnLdpLocMtu | 1.3.6.1.4.1.2352.2.39.3.4.1.12 | Unsigned32 | read-only | This object indicates the maximum transmission unit of the local VPN circuit. |
| U32 rbnMplsL2VpnLdpRemMtu | 1.3.6.1.4.1.2352.2.39.3.4.1.13 | Unsigned32 | read-only | This object indicates the maximum transmission unit of the remote connection. |
| T/F rbnMplsL2VpnLdpXcCctUp | 1.3.6.1.4.1.2352.2.39.3.4.1.14 | TruthValue | read-only | This object indicates the status of the VPN cross connect circuit state. A value of true indicates that the VPN circuit is connected with its remote site and attachment circuit is up (rbnMplsL2VpnLdpInputCctUp is true). A value of false indicates that the remote site is not presently connected, this mean that either the PSN is not reachable or the attachment circuit is down or signaling parameters mismatched. |
| U32 rbnMplsL2VpnLdpExpBits | 1.3.6.1.4.1.2352.2.39.3.4.1.15 | Unsigned32 | read-only | This object indicates the number of exp bits configured for this VPN circuit. |
| T/F rbnMplsL2VpnLdpInputCctUp | 1.3.6.1.4.1.2352.2.39.3.4.1.16 | TruthValue | read-only | This object indicates the status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is up. A value of false indicates the attachment circuit state is down. |
| RBN rbnMplsL2VpnLdpXcFlags | 1.3.6.1.4.1.2352.2.39.3.4.1.17 | RbnVpnXcFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| NUM rbnMplsL2VpnLdpIfIndexOrZero | 1.3.6.1.4.1.2352.2.39.3.4.1.18 | InterfaceIndexOrZero | read-only | This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry. |
| RBN rbnMplsL2VpnLdpPwFlags | 1.3.6.1.4.1.2352.2.39.3.4.1.19 | RbnVpnPwFlagsType | read-only | This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values. |
| RBN rbnMplsL2VpnLdpPwState | 1.3.6.1.4.1.2352.2.39.3.4.1.20 | RbnVpnPwStateType | read-only | This object indicates the status of the VPN input circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active(i.e. up) |
| rbnMplsL2VpnMIBConformance | 1.3.6.1.4.1.2352.2.39.4 | |||
| rbnMplsL2VpnMIBScalars | 1.3.6.1.4.1.2352.2.39.5 | |||
| T/F rbnMplsL2VpnNotificationEnable | 1.3.6.1.4.1.2352.2.39.5.1 | TruthValue | read-write | If this object is true, then it enables the generation of all notifications defined in this MIB. This object's value should be preserved across agent reboots. |
| rbnUdpL2VpnMIBObjects | 1.3.6.1.4.1.2352.2.39.6 | |||
| rbnUdpL2VpnStaticTable | 1.3.6.1.4.1.2352.2.39.6.1 | not-accessible | This table contains objects which identify static UDP Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured. | |
| rbnUdpL2VpnStaticEntry | 1.3.6.1.4.1.2352.2.39.6.1.1 | not-accessible | A conceptual row in the rbnUdpL2VpnStaticTable. | |
| INE rbnUdpL2VpnStaticPeerPort | 1.3.6.1.4.1.2352.2.39.6.1.1.1 | InetPortNumber | not-accessible | This object indicates the peer port number for this UDP L2 VPN circuit. |
| IPt rbnUdpL2VpnStaticPeerAddressType | 1.3.6.1.4.1.2352.2.39.6.1.1.2 | InetAddressType | not-accessible | This object indicates the peer IP address type for this UDP L2 VPN circuit. |
| IP rbnUdpL2VpnStaticPeerAddress | 1.3.6.1.4.1.2352.2.39.6.1.1.3 | InetAddress | not-accessible | This object indicates the peer IP address for this UDP L2 VPN circuit. The peer address type is determined by the value of the corresponding rbnUdpL2VpnStaticPeerAddressType. |
| IPt rbnUdpL2VpnStaticSourceAddressType | 1.3.6.1.4.1.2352.2.39.6.1.1.4 | InetAddressType | read-only | This object indicates the source IP address type for this UDP L2 VPN circuit. |
| IP rbnUdpL2VpnStaticSourceAddress | 1.3.6.1.4.1.2352.2.39.6.1.1.5 | InetAddress | read-only | This object indicates the source IP address for this UDP L2 VPN circuit. The source address type is determined by the value of the corresponding rbnUdpL2VpnStaticSourceAddressType. |
| INE rbnUdpL2VpnStaticSourcePort | 1.3.6.1.4.1.2352.2.39.6.1.1.6 | InetPortNumber | read-only | This object indicates the source port number for this UDP L2 VPN circuit. |
| RBN rbnUdpL2vpnStaticAccessCctHandle | 1.3.6.1.4.1.2352.2.39.6.1.1.7 | RbnCircuitHandle | read-only | This object indicates the internal representation of the access circuit for this UDP L2 VPN circuit. |
| RBN rbnUdpL2VpnStaticVpnCctHandle | 1.3.6.1.4.1.2352.2.39.6.1.1.8 | RbnCircuitHandle | read-only | This object indicates the internal representation of this UDP L2 VPN circuit. |
| T/F rbnUdpL2VpnStaticInputCctUp | 1.3.6.1.4.1.2352.2.39.6.1.1.9 | TruthValue | read-only | This object indicates the status of this UDP L2 VPN circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected. |
| NUM rbnUdpL2VpnStaticIfIndexOrZero | 1.3.6.1.4.1.2352.2.39.6.1.1.10 | InterfaceIndexOrZero | read-only | This object indicates whether there is a corresponding entry of this UDP L2 VPN access circuit in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry (for example, a pre-provisioned access circuit is used). |
| RBN rbnUdpL2VpnStaticPwFlags | 1.3.6.1.4.1.2352.2.39.6.1.1.11 | RbnVpnPwFlagsType | read-only | This object indicates more detailed information on the status of this UDP L2 VPN circuit. This object is a bit field so it may contain one or more of these values. |
| INT rbnUdpL2vpnStaticDscpCode | 1.3.6.1.4.1.2352.2.39.6.1.1.12 | INTEGER | read-only | Diffserver code for the CES over UDP PW. Default is Zero. The dscp code values are listed as follows: 0..63 Differentiated services codepoint value af11 Assured Forwarding - Class 1/Drop precedence 1 af12 Assured Forwarding - Class 1/Drop precedence 2 af13 Assured Forwarding - Class 1/Drop precedence 3 af21 Assured Forwarding - Class 2/Drop precedence 1 af22 Assured Forwarding - Class 2/Drop precedence 2 af23 Assured Forwarding - Class 2/Drop precedence 3 af31 Assured Forwarding - Class 3/Drop precedence 1 af32 Assured Forwarding - Class 3/Drop precedence 2 af33 Assured Forwarding - Class 3/Drop precedence 3 af41 Assured Forwarding - Class 4/Drop precedence 1 af42 Assured Forwarding - Class 4/Drop precedence 2 af43 Assured Forwarding - Class 4/Drop precedence 3 |
| RBN rbnUdpL2VpnStaticPwState | 1.3.6.1.4.1.2352.2.39.6.1.1.13 | RbnVpnPwStateType | read-only | This object indicates the status of this UDP L2 VPN circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active (i.e. up) |
| RBN rbnUdpL2VpnStaticPsnType | 1.3.6.1.4.1.2352.2.39.6.1.1.14 | RbnVpnPsnType | read-only | This object indicates the packet switched networks(PSN) type for this UDP L2 VPN circuit. |
RFC description
Defines Layer 2 VPN management objects for Redback Networks (Ericsson) devices, supporting static and protocol-based L2VPN circuit monitoring and configuration.
Start monitoring Ericsson SmartEdge router/BRAS platform (Layer 2 VPN / MPLS pseudowire management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.