RAD-DS1-MIB

All MIBs › RAD-DS1-MIB

Category: DS1 and T-Carrier

Description:

Manages RAD Data Communications DS1/T1 interface configuration, framing, line coding, and performance monitoring.

Imported Objects

ifAlias

OBJECT-TYPE

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount
PerfTotalCount

From RAD-MIB

alarmSeverity	OBJECT-TYPE
alarmState	OBJECT-TYPE
diverseIfWanGen	OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Integer32
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

TruthValue

What Is RAD-DS1-MIB?

RAD-DS1-MIB is a RAD Data Communications proprietary MIB extending the standard DS1/T1 MIB with additional current- and interval-statistics objects (built on RAD-GEN-MIB/RAD-MIB). Its current-statistics table reports live DS1 alarm conditions — loss of signal (LOS), loss of frame (LOF), loss of carrier (LOC), AIS, remote alarm indication (RAI), CRC multiframe loss, far-end block errors (FEBE), bipolar violations (BPV), and CRC errors — while a parallel interval table records the same set of counters per 15-minute interval. As a performance/hardware-status MIB it lets an administrator pinpoint exactly which DS1 alarm condition (LOS vs. AIS vs. bipolar violations) is driving circuit errors and how it trends over recent intervals. It is deployed on RAD Data Communications DS1/T1 access equipment. Engineers can download the RAD-DS1-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAD-DS1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

DS1 current and interval alarm/error counters

Supported Devices

RAD Data Communications DS1/T1 access equipment

Monitoring Examples

An administrator checks dsx1CurrentBPV and dsx1IntervalBPV across recent 15-minute intervals to determine whether bipolar violations on a DS1 circuit are a one-off event or a persistent line-quality problem.

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines whether CSU loop will be done locally (by IPmux) or will be transferred to the TDM device.
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) .
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Determine the maximum attenuation of the receive signal that can be compensated for by the interface receive path. Not applicable for T1.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1

OID symbolic	OID numeric	Type	Access	Description
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) .
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Determine the maximum attenuation of the receive signal that can be compensated for by the interface receive path. Not applicable for T1.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate.
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines whether CSU loop will be done locally (by IPmux) or will be transferred to the TDM device.
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.

Counter32 (7)
C32 dsx1DataStreamStatInBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.5	Counter32	read-only	The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.6	Counter32	read-only	The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInErrors	1.3.6.1.4.1.164.3.1.6.4.1.5.1.7	Counter32	read-only	The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatInFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.4	Counter32	read-only	The counter associated with the number of received frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutBytes	1.3.6.1.4.1.164.3.1.6.4.1.5.1.9	Counter32	read-only	The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutDiscards	1.3.6.1.4.1.164.3.1.6.4.1.5.1.10	Counter32	read-only	The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
C32 dsx1DataStreamStatOutFrames	1.3.6.1.4.1.164.3.1.6.4.1.5.1.8	Counter32	read-only	The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
INTEGER (14)
INT dsx1AisEnable	1.3.6.1.4.1.164.3.1.6.4.2.1.12	INTEGER	read-write	Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
INT dsx1CsuLoop	1.3.6.1.4.1.164.3.1.6.4.2.1.18	INTEGER	read-write	This parameter defines whether CSU loop will be done locally (by IPmux) or will be transferred to the TDM device.
INT dsx1dBTxGain	1.3.6.1.4.1.164.3.1.6.4.2.1.3	INTEGER	read-write	Transmit line Gain for T1 CSU line mode.
INT dsx1EchoCancelerModule	1.3.6.1.4.1.164.3.1.6.4.2.1.14	INTEGER	read-only	This parameter indicates whether echo-cancellation module exists for this line.
INT dsx1LeasedLine	1.3.6.1.4.1.164.3.1.6.4.2.1.17	INTEGER	read-write	This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
INT dsx1LineAdaptiveTimingMode	1.3.6.1.4.1.164.3.1.6.4.2.1.10	INTEGER	read-write	Enables end to end clock synchronization. Default value - off.
INT dsx1LineMode	1.3.6.1.4.1.164.3.1.6.4.2.1.2	INTEGER	read-write	T1 device operation mode. Valid for T1 only.
INT dsx1OosSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.20	INTEGER	read-write	This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
INT dsx1PortFunction	1.3.6.1.4.1.164.3.1.6.4.2.1.15	INTEGER	read-write	This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM.
INT dsx1PortMultiplier	1.3.6.1.4.1.164.3.1.6.4.2.1.16	INTEGER	read-write	This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
INT dsx1RestoreTime	1.3.6.1.4.1.164.3.1.6.4.2.1.5	INTEGER	read-write	Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
INT dsx1RxSensitivity	1.3.6.1.4.1.164.3.1.6.4.2.1.4	INTEGER	read-write	Determine the maximum attenuation of the receive signal that can be compensated for by the interface receive path. Not applicable for T1.
INT dsx1Scramble	1.3.6.1.4.1.164.3.1.6.4.2.1.9	INTEGER	read-write	Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
INT dsx1TxClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.11	INTEGER	read-write	The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate.
Integer32 (7)
I32 dsx1ClockSource	1.3.6.1.4.1.164.3.1.6.4.2.1.19	Integer32	read-write	This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
I32 dsx1DataStreamStatIfIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.1	Integer32	not-accessible	The index of the DS1 interface. It may be ifIndex.
I32 dsx1DataStreamStatIndex	1.3.6.1.4.1.164.3.1.6.4.1.5.1.2	Integer32	not-accessible	The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) .
I32 dsx1IdleCode	1.3.6.1.4.1.164.3.1.6.4.2.1.1	Integer32	read-write	Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
I32 dsx1TcFirstSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.6	Integer32	read-write	Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
I32 dsx1TcPattern	1.3.6.1.4.1.164.3.1.6.4.2.1.8	Integer32	read-write	Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
I32 dsx1TcSignal	1.3.6.1.4.1.164.3.1.6.4.2.1.7	Integer32	read-write	Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
OCTET STRING (3)
OCT dsx1CurrentStatus	1.3.6.1.4.1.164.3.1.6.4.1.2.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT dsx1IntervalStatus	1.3.6.1.4.1.164.3.1.6.4.1.3.1.8	OCTET STRING	read-only	The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
OCT dsx1TsEchoCancel	1.3.6.1.4.1.164.3.1.6.4.2.1.13	OCTET STRING	read-write	This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
PerfCurrentCount (11)
PER dsx1CurrentAIS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.4	PerfCurrentCount	read-only	The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentBPV	1.3.6.1.4.1.164.3.1.6.4.1.2.1.9	PerfCurrentCount	read-only	The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentCRCErrors	1.3.6.1.4.1.164.3.1.6.4.1.2.1.12	PerfCurrentCount	read-only	Counts the number of CRC error events, encountered in the current 15 minute interval.
PER dsx1CurrentFEBE	1.3.6.1.4.1.164.3.1.6.4.1.2.1.7	PerfCurrentCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
PER dsx1CurrentLOC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.3	PerfCurrentCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
PER dsx1CurrentLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.10	PerfCurrentCount	read-only	Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
PER dsx1CurrentLOF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.2	PerfCurrentCount	read-only	The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentLOFC	1.3.6.1.4.1.164.3.1.6.4.1.2.1.11	PerfCurrentCount	read-only	Counts the number of loss of frame events measured. encountered in the current 15 minute interval
PER dsx1CurrentLOMF	1.3.6.1.4.1.164.3.1.6.4.1.2.1.6	PerfCurrentCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
PER dsx1CurrentLOS	1.3.6.1.4.1.164.3.1.6.4.1.2.1.1	PerfCurrentCount	read-only	The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
PER dsx1CurrentRAI	1.3.6.1.4.1.164.3.1.6.4.1.2.1.5	PerfCurrentCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
PerfIntervalCount (10)
NUM dsx1IntervalAIS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.4	PerfIntervalCount	read-only	The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalBPV	1.3.6.1.4.1.164.3.1.6.4.1.3.1.9	PerfIntervalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalFEBE	1.3.6.1.4.1.164.3.1.6.4.1.3.1.7	PerfIntervalCount	read-only	Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
NUM dsx1IntervalLOC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.3	PerfIntervalCount	read-only	Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
NUM dsx1IntervalLOCRCMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.10	PerfIntervalCount	read-only	Loss of CRC4 Multi-Frame sequence in E1.
NUM dsx1IntervalLOF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.2	PerfIntervalCount	read-only	The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.3.1.11	PerfIntervalCount	read-only	Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalLOMF	1.3.6.1.4.1.164.3.1.6.4.1.3.1.6	PerfIntervalCount	read-only	Loss of Multi-Frame sequence in E1 time slot 16.
NUM dsx1IntervalLOS	1.3.6.1.4.1.164.3.1.6.4.1.3.1.1	PerfIntervalCount	read-only	The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
NUM dsx1IntervalRAI	1.3.6.1.4.1.164.3.1.6.4.1.3.1.5	PerfIntervalCount	read-only	Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
PerfTotalCount (3)
PER dsx1TotalBPV	1.3.6.1.4.1.164.3.1.6.4.1.4.1.9	PerfTotalCount	read-only	The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOFC	1.3.6.1.4.1.164.3.1.6.4.1.4.1.11	PerfTotalCount	read-only	The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
PER dsx1TotalLOS	1.3.6.1.4.1.164.3.1.6.4.1.4.1.1	PerfTotalCount	read-only	The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
TruthValue (1)
T/F dsx1DataStreamStatValid	1.3.6.1.4.1.164.3.1.6.4.1.5.1.3	TruthValue	read-only	Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
No type (33)
NTF ds1AisSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.10			This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
NTF ds1AisTrap	1.3.6.1.4.1.164.3.1.6.4.0.11			This trap indicates AIS being received at the user DS1 interface.
NTF ds1BpvErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.4			This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
NTF ds1Crc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.6			This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
NTF ds1ExcessiveBpvTrap	1.3.6.1.4.1.164.3.1.6.4.0.5			This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
NTF ds1ExcessiveCrc4ErrorTrap	1.3.6.1.4.1.164.3.1.6.4.0.16			This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
NTF ds1ExcessiveErrorRatioTrap	1.3.6.1.4.1.164.3.1.6.4.0.7			This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
NTF ds1ExcessiveFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.15			This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
NTF ds1ExcessiveLocalMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.17			This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveLocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.20			This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteMfAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.18			This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
NTF ds1ExcessiveRemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.19			This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
ds1Interface	1.3.6.1.4.1.164.3.1.6.4
NTF ds1LinkFrameSlipTrap	1.3.6.1.4.1.164.3.1.6.4.0.3			This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
NTF ds1LocalLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.14			This trap indicates that a local loopback has been activated on the user port.
NTF ds1LocalMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.1			This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
NTF ds1LocalSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.9			This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
NTF ds1NetworkRemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.12			This trap indicates that a remote loopback has been activated, on the local uplink interface.
NTF ds1RemoteLoopTrap	1.3.6.1.4.1.164.3.1.6.4.0.13			This trap indicates that a remote loopback has been activated, on the local user port.
NTF ds1RemoteMultiframeAlarmTrap	1.3.6.1.4.1.164.3.1.6.4.0.2			This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
NTF ds1RemoteSyncLossTrap	1.3.6.1.4.1.164.3.1.6.4.0.8			This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
dsx1DataStreamStatEntry	1.3.6.1.4.1.164.3.1.6.4.1.5.1		not-accessible	An entry in the DS1 Data Stream Statistics table.
dsx1DataStreamStatTable	1.3.6.1.4.1.164.3.1.6.4.1.5		not-accessible	The DS1 Data Stream Statistics table.
dsx1XConfigEntry	1.3.6.1.4.1.164.3.1.6.4.2.1		not-accessible	An entry containing additional configuration parameters.
dsx1XConfigTable	1.3.6.1.4.1.164.3.1.6.4.2		not-accessible	An extension to the DS1 Configuration table.
dsx1XCurrentEntry	1.3.6.1.4.1.164.3.1.6.4.1.2.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XCurrentTable	1.3.6.1.4.1.164.3.1.6.4.1.2		not-accessible	A list of current statistics entries. This table contains additional objects for the current table.
dsx1XIntervalEntry	1.3.6.1.4.1.164.3.1.6.4.1.3.1		not-accessible	An entry containing additional statistical counters applicable to a particular interval table.
dsx1XIntervalTable	1.3.6.1.4.1.164.3.1.6.4.1.3		not-accessible	A list of Interval entries. This table contains additional objects for the interval table.
dsx1XTotalEntry	1.3.6.1.4.1.164.3.1.6.4.1.4.1		not-accessible	An entry containing additional statistical counters applicable to a particular current table.
dsx1XTotalTable	1.3.6.1.4.1.164.3.1.6.4.1.4		not-accessible	A list of Total statistics entries. This table contains additional objects for the Total table.
prtDS1Events	1.3.6.1.4.1.164.3.1.6.4.0
prtDs1PerfHistory	1.3.6.1.4.1.164.3.1.6.4.1

RFC description

DS1 interface performance statistics and error counters for current interval monitoring.

Start monitoring RAD Data Communications DS1/T1 access equipment (alarm/interval statistics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAD-DS1-MIB

This MIB depends on

Related MIBs

What Is RAD-DS1-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description