All MIBs › PRVT-RAPS-MIB
Organization: BATM Advanced Communication
Last Updated: 2010-11-11
Category: Carrier Ethernet, Protection and Redundancy
Description: Manages BATM Advanced Communication G.8032 Ring Automatic Protection Switching (RAPS) ring instance and node configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is PRVT-RAPS-MIB?
This is a private/enterprise MIB implementing ITU-T G.8032 Ethernet Ring Automatic Protection Switching (ERPS) configuration and status for ring-topology carrier Ethernet networks. It exposes a ring-instance table with role (RPL owner/neighbor), control VLAN, CFM domain level used for fault detection, revertive-mode behavior, virtual channel setting, and hold-off timer, plus notifications for ring protection events. It supports monitoring of the software/protocol health of the ring protection mechanism, tracking each ring instance's operational role and control VLAN to detect misconfigured or degraded ring nodes, and using notifications to alert on ring topology changes (link failures, switchovers) that would otherwise cause a network outage. It explicitly depends on IEEE 802.1ag/ITU-T Y.1731 Connectivity Fault Management (CFM), referenced via prvtRapsInstCfmDomainLevel, for the continuity-check mechanism that drives ring protection switching. Typical deployment is on carrier Ethernet ring switches used in metro/access ring topologies requiring sub-50ms protection switching. Engineers can download the PRVT-RAPS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in PRVT-RAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- carrier Ethernet ring switch (G.8032 ERPS)
Monitoring Examples
An operator would poll prvtRapsInstTable/prvtRapsInstEntry, indexed by prvtRapsInstIndex, for prvtRapsInstRole, prvtRapsInstRingId, and prvtRapsInstControlVlan to confirm each node's ring role and VLAN assignment. If prvtRapsInstRevertiveMode is enabled but a ring stays in a non-reverted state after a fault clears, or a prvtRapsMIBNotifications trap fires repeatedly for the same prvtRapsInstRingId, it points to a flapping link or a misconfigured prvtRapsInstHoldOffTimer. prvtRapsInstCfmDomainLevel confirms which CFM maintenance domain drives the ring's continuity-check-based fault detection.
What Can Be Monitored
- ring instance role (owner/neighbor)
- ring protection switchover events
- control VLAN assignment
- CFM domain level
- revertive mode state
- hold-off timer setting
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From PRVT-QOS-MIB
| serviceAccessSwitch | OBJECT-IDENTITY |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF prvtRapsDefectAlarm | 1.3.6.1.4.1.738.1.7.4.0.1 | This trap will be sent by any instance when it notices a defect. So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own. The management entity receiving the notification can identify the system from the network source address of the notification. | ||
| PRV prvtRapsInstCfmDomainLevel | 1.3.6.1.4.1.738.1.7.4.1.1.1.7 | PrvtRapsCfmLevelType | read-create | The CFM domain level for this R-APS instance. Must perform shutdown to change this object. |
| PRV prvtRapsInstClear | 1.3.6.1.4.1.738.1.7.4.1.1.1.15 | PrvtRapsActionType | read-create | Sends the Clear command to this R-APS instance. |
| INT prvtRapsInstControlProtocol | 1.3.6.1.4.1.738.1.7.4.1.1.1.20 | INTEGER | read-create | The protocol that controls the main ring. |
| PRV prvtRapsInstControlVlan | 1.3.6.1.4.1.738.1.7.4.1.1.1.6 | PrvtRapsVlanIdType | read-create | The control VLAN for this R-APS instance. When main ring's control protocol is vpls (prvtRapsInstControlProtocol equals 'vpls'), this should be set equal to the ring's instance ID (prvtRapsInstIndex). This object must be set to the ID of an existing VLAN. Each R-APS instance must use a unique VLAN for the control VLAN. Must perform shutdown to change this object. |
| STR prvtRapsInstDescription | 1.3.6.1.4.1.738.1.7.4.1.1.1.19 | DisplayString | read-create | RAPS instance description. |
| T/F prvtRapsInstDisableVirtChan | 1.3.6.1.4.1.738.1.7.4.1.1.1.9 | TruthValue | read-create | Set to 'true' to select that the node is part of a sub-ring without a RAPS virtual channel. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). Must be set 'false' when in version 1 mode. |
| prvtRapsInstEntry | 1.3.6.1.4.1.738.1.7.4.1.1.1 | not-accessible | An entry in prvtRapsInstTable. | |
| PRV prvtRapsInstGuardTimer | 1.3.6.1.4.1.738.1.7.4.1.1.1.12 | PrvtRapsGuardTimerType | read-create | The guard timer time-out value for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). |
| PRV prvtRapsInstHoldOffTimer | 1.3.6.1.4.1.738.1.7.4.1.1.1.10 | PrvtRapsHoldOffType | read-create | The hold-off timer time-out value for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). |
| PRV prvtRapsInstIndex | 1.3.6.1.4.1.738.1.7.4.1.1.1.1 | PrvtRapsInstIndexType | not-accessible | An arbitrary index uniquely identifying a Ring APS instance. |
| PRV prvtRapsInstMode | 1.3.6.1.4.1.738.1.7.4.1.1.1.3 | PrvtRapsModeType | read-create | The G.8032 mode for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). In version 1 mode (prvtRapsInstMode equals 'version1'), ring ID (prvtRapsInstRingId) must be 1. |
| prvtRapsInstMonVlanEntry | 1.3.6.1.4.1.738.1.7.4.1.2.1 | not-accessible | An entry in prvtRapsInstMonVlanTable. | |
| PRV prvtRapsInstMonVlanId | 1.3.6.1.4.1.738.1.7.4.1.2.1.1 | PrvtRapsVlanIdType | not-accessible | Uniquely identifies a VLAN to be monitored. This object must be the ID of an existing VLAN. Must not be the same VLAN as the control VLAN (prvtRapsInstControlVlan). |
| ROW prvtRapsInstMonVlanRowStatus | 1.3.6.1.4.1.738.1.7.4.1.2.1.2 | RowStatus | read-create | The RowStatus for this monitored VLAN. |
| prvtRapsInstMonVlanTable | 1.3.6.1.4.1.738.1.7.4.1.2 | not-accessible | Monitor VLAN Table Each entry in this table defines a VLAN that will be monitored. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). | |
| PRV prvtRapsInstOperStatus | 1.3.6.1.4.1.738.1.7.4.1.1.1.16 | PrvtRapsInstStatusType | read-only | The operational status of this R-APS instance. |
| prvtRapsInstPortStatusEntry | 1.3.6.1.4.1.738.1.7.4.1.5.1 | not-accessible | An entry in prvtRapsInstPortStatusTable. | |
| PRV prvtRapsInstPortStatusIfIndex | 1.3.6.1.4.1.738.1.7.4.1.5.1.1 | PrvtRapsIfIndexOrAgIdType | not-accessible | Uniquely identifies a physical port (ifIndex) or a LAG port (LAG ID) belonging to a R-APS instance. |
| PRV prvtRapsInstPortStatusLink | 1.3.6.1.4.1.738.1.7.4.1.5.1.2 | PrvtRapsLinkOperStatusType | read-only | The operational status of this port. |
| PRV prvtRapsInstPortStatusRcvdCmd | 1.3.6.1.4.1.738.1.7.4.1.5.1.5 | PrvtRapsReceivedCommandType | read-only | The command received on this port. |
| PRV prvtRapsInstPortStatusRcvdInfo | 1.3.6.1.4.1.738.1.7.4.1.5.1.6 | PrvtRapsReceivedInfoType | read-only | The info received on this port. |
| MAC prvtRapsInstPortStatusRcvdNodeId | 1.3.6.1.4.1.738.1.7.4.1.5.1.4 | MacAddress | read-only | The MAC address of the remote R-APS device connected to this port. |
| PRV prvtRapsInstPortStatusRemoteMep | 1.3.6.1.4.1.738.1.7.4.1.5.1.3 | PrvtRapsMepIdType | read-only | The maintenance entity group end point ID for the remote port connected to this port. |
| prvtRapsInstPortStatusTable | 1.3.6.1.4.1.738.1.7.4.1.5 | not-accessible | R-APS Instance Port Status Table Each entry in this table gives status information concerning a particular port (physical port or LAG interface port) belonging to a R-APS instance. | |
| PRV prvtRapsInstRapsState | 1.3.6.1.4.1.738.1.7.4.1.1.1.17 | PrvtRapsStatesType | read-only | The current state for this R-APS instance. |
| T/F prvtRapsInstRevertiveMode | 1.3.6.1.4.1.738.1.7.4.1.1.1.8 | TruthValue | read-create | Set to 'true' to select revertive behavior for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). Non-revertive behavior is not available in version 1 mode. |
| PRV prvtRapsInstRingId | 1.3.6.1.4.1.738.1.7.4.1.1.1.4 | PrvtRapsRingIdType | read-create | The Ring ID for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). In version 1 mode (prvtRapsInstMode equals 'version1'), ring ID (prvtRapsInstRingId) must be 1. |
| prvtRapsInstRingLagEntry | 1.3.6.1.4.1.738.1.7.4.1.4.1 | not-accessible | An entry in prvtRapsInstRingLagTable. | |
| PRV prvtRapsInstRingLagForcedSwitch | 1.3.6.1.4.1.738.1.7.4.1.4.1.7 | PrvtRapsActionType | read-create | Send the Forced Switch command to this LAG interface. |
| PRV prvtRapsInstRingLagId | 1.3.6.1.4.1.738.1.7.4.1.4.1.3 | PrvtRapsLinkAggIdType | read-create | The ID of a LAG interface belonging to a R-APS instance. This object must be set to the ID of an existing LAG interface. No two LAG ports within the same ring instance can use the same LAG port. |
| U32 prvtRapsInstRingLagIndex | 1.3.6.1.4.1.738.1.7.4.1.4.1.1 | Unsigned32 | not-accessible | An arbitrary index uniquely identifying a LAG interface belonging to a R-APS instance. When a physical port and a LAG port are used in the same R-APS instance, the two ports must use unique index values (i.e. prvtRapsInstRingPortIndex must not equal prvtRapsInstRingLagIndex). |
| PRV prvtRapsInstRingLagManSwitch | 1.3.6.1.4.1.738.1.7.4.1.4.1.6 | PrvtRapsActionType | read-create | Send the Manual Switch command to this LAG interface. |
| PRV prvtRapsInstRingLagMep | 1.3.6.1.4.1.738.1.7.4.1.4.1.4 | PrvtRapsMepIdType | read-create | The peer maintenance entity group end point ID that should monitor this LAG interface. No two LAG ports within the same ring instance can use the same MEP ID. |
| ROW prvtRapsInstRingLagRowStatus | 1.3.6.1.4.1.738.1.7.4.1.4.1.2 | RowStatus | read-create | The RowStatus for this LAG interface. |
| T/F prvtRapsInstRingLagRpl | 1.3.6.1.4.1.738.1.7.4.1.4.1.5 | TruthValue | read-create | Set to 'true' to define this ring LAG port as a Ring Protection Link port. Exactly one RPL port must be defined when ring role (prvtRapsInstRole) is not 'simpleNode'. In 'simpleNode' role, no RPL ports must be defined. |
| prvtRapsInstRingLagTable | 1.3.6.1.4.1.738.1.7.4.1.4 | not-accessible | R-APS Instance Ring LAG Table Each entry in this table defines a Link Aggregation Group interface belonging to a R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). Exactly two interfaces must be defined per instance. This includes physical ports (defined in prvtRapsInstRingPortTable) and LAG interfaces (defined in prvtRapsInstRingLagTable). | |
| prvtRapsInstRingPortEntry | 1.3.6.1.4.1.738.1.7.4.1.3.1 | not-accessible | An entry in prvtRapsInstRingPortTable. | |
| PRV prvtRapsInstRingPortForcedSwitch | 1.3.6.1.4.1.738.1.7.4.1.3.1.7 | PrvtRapsActionType | read-create | Send the Forced Switch command to this ring port. |
| NUM prvtRapsInstRingPortIfIndex | 1.3.6.1.4.1.738.1.7.4.1.3.1.3 | InterfaceIndex | read-create | The ifIndex of the physical port assigned to this ring port. No two ports within the same ring instance can use the same physical port. |
| U32 prvtRapsInstRingPortIndex | 1.3.6.1.4.1.738.1.7.4.1.3.1.1 | Unsigned32 | not-accessible | An arbitrary index uniquely identifying a physical port belonging to a R-APS instance. When a physical port and a LAG port are used in the same R-APS instance, the two ports must use unique index values (i.e. prvtRapsInstRingPortIndex must not equal prvtRapsInstRingLagIndex). |
| PRV prvtRapsInstRingPortManSwitch | 1.3.6.1.4.1.738.1.7.4.1.3.1.6 | PrvtRapsActionType | read-create | Send the Manual Switch command to this ring port. |
| PRV prvtRapsInstRingPortMep | 1.3.6.1.4.1.738.1.7.4.1.3.1.4 | PrvtRapsMepIdType | read-create | The peer maintenance entity group end point ID that should monitor this ring port. No two ports within the same ring instance can use the same MEP ID. |
| PRV prvtRapsInstRingPortMonitoringMethod | 1.3.6.1.4.1.738.1.7.4.1.3.1.8 | PrvtRapsMonitoringMethodType | read-create | Ethernet ring protection monitoring methods |
| ROW prvtRapsInstRingPortRowStatus | 1.3.6.1.4.1.738.1.7.4.1.3.1.2 | RowStatus | read-create | The RowStatus for this ring port. |
| T/F prvtRapsInstRingPortRpl | 1.3.6.1.4.1.738.1.7.4.1.3.1.5 | TruthValue | read-create | Set to 'true' to define this ring port as a Ring Protection Link port. Exactly one RPL port must be defined when ring role (prvtRapsInstRole) is not 'simpleNode'. In 'simpleNode' role, no RPL ports must be defined. |
| prvtRapsInstRingPortTable | 1.3.6.1.4.1.738.1.7.4.1.3 | not-accessible | R-APS Instance Ring Port Table. Each entry in this table defines a port belonging to a R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). Exactly two interfaces must be defined per instance. This includes physical ports (defined in prvtRapsInstRingPortTable) and LAG interfaces (defined in prvtRapsInstRingLagTable). In the case when one physical port and one LAG interface is used, the two port index values must be unique (i.e. prvtRapsInstRingPortIndex must not equal prvtRapsInstRingLagIndex) | |
| PRV prvtRapsInstRole | 1.3.6.1.4.1.738.1.7.4.1.1.1.5 | PrvtRapsRoleType | read-create | The role of the node for this R-APS instance. Must perform shutdown to change this object. |
| ROW prvtRapsInstRowStatus | 1.3.6.1.4.1.738.1.7.4.1.1.1.2 | RowStatus | read-create | The RowStatus for this R-APS instance. |
| T/F prvtRapsInstShutdown | 1.3.6.1.4.1.738.1.7.4.1.1.1.14 | TruthValue | read-create | Set to 'true' to de-activate this R-APS instance. |
| PRV prvtRapsInstSubRingBlockTimer | 1.3.6.1.4.1.738.1.7.4.1.6.1.10 | PrvtRapsBlockTimerType | read-only | The wait to block timer time-out value for this sub-ring. |
| PRV prvtRapsInstSubRingClear | 1.3.6.1.4.1.738.1.7.4.1.6.1.13 | PrvtRapsActionType | read-create | Send the Clear command to this sub-ring. |
| PRV prvtRapsInstSubRingControlVlan | 1.3.6.1.4.1.738.1.7.4.1.6.1.29 | PrvtRapsVlanIdType | read-create | The control VLAN for this sub-ring. This object must be set to the ID of an existing VLAN. Must not be the same VLAN as a monitored VLAN in any instance. Must perform shutdown to change this object. |
| NTF prvtRapsInstSubRingDefectAlarm | 1.3.6.1.4.1.738.1.7.4.0.3 | This trap will be sent by any subring instance when it notices a defect. So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRapsInstSubRingOperStatus variable in the notification. | ||
| STR prvtRapsInstSubRingDescription | 1.3.6.1.4.1.738.1.7.4.1.6.1.24 | DisplayString | read-create | RAPS instance sub-ring description. |
| prvtRapsInstSubRingEntry | 1.3.6.1.4.1.738.1.7.4.1.6.1 | not-accessible | An entry in prvtRapsInstSubRingTable. | |
| PRV prvtRapsInstSubRingForcedSwitch | 1.3.6.1.4.1.738.1.7.4.1.6.1.15 | PrvtRapsActionType | read-create | Send the Forced Switch command to this sub-ring. |
| PRV prvtRapsInstSubRingGuardTimer | 1.3.6.1.4.1.738.1.7.4.1.6.1.9 | PrvtRapsGuardTimerType | read-create | The guard timer time-out value for this sub-ring. |
| PRV prvtRapsInstSubRingHoldOffTimer | 1.3.6.1.4.1.738.1.7.4.1.6.1.7 | PrvtRapsHoldOffType | read-create | The hold-off timer time-out value for this sub-ring. |
| PRV prvtRapsInstSubRingId | 1.3.6.1.4.1.738.1.7.4.1.6.1.3 | PrvtRapsRingIdType | read-create | The ring ID for this sub-ring. |
| PRV prvtRapsInstSubRingIndex | 1.3.6.1.4.1.738.1.7.4.1.6.1.1 | PrvtRapsInstIndexType | not-accessible | An arbitrary index uniquely identifying a sub-ring for this R-APS instance. |
| prvtRapsInstSubRingLagEntry | 1.3.6.1.4.1.738.1.7.4.1.8.1 | not-accessible | An entry in prvtRapsInstSubRingLagTable. | |
| PRV prvtRapsInstSubRingLagId | 1.3.6.1.4.1.738.1.7.4.1.8.1.1 | PrvtRapsLinkAggIdType | not-accessible | Uniquely identifies a LAG interface belonging to a sub-ring. Must be set to the LAG ID of an existing LAG interface. A sub-ring LAG port can not be part of the main ring. |
| PRV prvtRapsInstSubRingLagMep | 1.3.6.1.4.1.738.1.7.4.1.8.1.3 | PrvtRapsMepIdType | read-create | The peer maintenance entity group end point ID that should monitor this sub-ring LAG interface. A sub-ring MEP can not be used in another ring. |
| PRV prvtRapsInstSubRingLagMonitoringMethod | 1.3.6.1.4.1.738.1.7.4.1.8.1.5 | PrvtRapsMonitoringMethodType | read-create | Ethernet ring protection monitoring methods |
| ROW prvtRapsInstSubRingLagRowStatus | 1.3.6.1.4.1.738.1.7.4.1.8.1.2 | RowStatus | read-create | The RowStatus for this sub-ring LAG interface. |
| T/F prvtRapsInstSubRingLagRpl | 1.3.6.1.4.1.738.1.7.4.1.8.1.4 | TruthValue | read-create | Set to 'true' to define this sub-ring LAG port as a Ring Protection Link port. Exactly one RPL port must be defined when sub-ring role (prvtRapsInstSubRingRole) is not 'simpleNode'. In 'simpleNode' role, no RPL ports must be defined. |
| prvtRapsInstSubRingLagTable | 1.3.6.1.4.1.738.1.7.4.1.8 | not-accessible | R-APS Instance Sub-ring LAG interface Table An entry in this table defines a LAG interface belonging to a sub-ring. Exactly one interface must be defined per sub-ring. This includes physical ports (defined in prvtRapsInstSubRingPortTable) and LAG interfaces (defined in prvtRapsInstSubRingLagTable). | |
| PRV prvtRapsInstSubRingLinkStatus | 1.3.6.1.4.1.738.1.7.4.1.6.1.20 | PrvtRapsLinkOperStatusType | read-only | The operational status of the port belonging to this sub-ring. |
| PRV prvtRapsInstSubRingManualSwitch | 1.3.6.1.4.1.738.1.7.4.1.6.1.14 | PrvtRapsActionType | read-create | Send the Manual Switch command to this sub-ring. |
| PRV prvtRapsInstSubRingOperStatus | 1.3.6.1.4.1.738.1.7.4.1.6.1.16 | PrvtRapsInstStatusType | read-only | The operational status of this sub-ring. |
| prvtRapsInstSubRingPortEntry | 1.3.6.1.4.1.738.1.7.4.1.7.1 | not-accessible | An entry in prvtRapsInstSubRingPortTable. | |
| PRV prvtRapsInstSubRingPortMep | 1.3.6.1.4.1.738.1.7.4.1.7.1.2 | PrvtRapsMepIdType | read-create | The peer maintenance entity group end point ID that should monitor this sub-ring port. A sub-ring MEP can not be used in another ring. |
| PRV prvtRapsInstSubRingPortMonitoringMethod | 1.3.6.1.4.1.738.1.7.4.1.7.1.4 | PrvtRapsMonitoringMethodType | read-create | Ethernet ring protection monitoring methods |
| OCT prvtRapsInstSubRingPortName | 1.3.6.1.4.1.738.1.7.4.1.6.1.19 | OCTET STRING | read-only | The textual name of the port belonging to this sub-ring. For a physical port, the format is U/S/P. For a LAG interface, the format is agX. |
| ROW prvtRapsInstSubRingPortRowStatus | 1.3.6.1.4.1.738.1.7.4.1.7.1.1 | RowStatus | read-create | The RowStatus for this sub-ring port. |
| T/F prvtRapsInstSubRingPortRpl | 1.3.6.1.4.1.738.1.7.4.1.7.1.3 | TruthValue | read-create | Set to 'true' to define this sub-ring port as a Ring Protection Link port. Exactly one RPL port must be defined when sub-ring role (prvtRapsInstSubRingRole) is not 'simpleNode'. In 'simpleNode' role, no RPL ports must be defined. |
| prvtRapsInstSubRingPortTable | 1.3.6.1.4.1.738.1.7.4.1.7 | not-accessible | R-APS Instance Sub-ring port Table An entry in this table defines a physical port belonging to a sub-ring. Exactly one interface must be defined per sub-ring. This includes physical ports (defined in prvtRapsInstSubRingPortTable) and LAG interfaces (defined in prvtRapsInstSubRingLagTable). A sub-ring port can not be part of the main ring. | |
| T/F prvtRapsInstSubRingPropTopChng | 1.3.6.1.4.1.738.1.7.4.1.6.1.11 | TruthValue | read-create | Set to 'true' to enable topology change propagation for this sub-ring. |
| PRV prvtRapsInstSubRingRapsState | 1.3.6.1.4.1.738.1.7.4.1.6.1.17 | PrvtRapsStatesType | read-only | The current state of this sub-ring. |
| PRV prvtRapsInstSubRingRcvdCmd | 1.3.6.1.4.1.738.1.7.4.1.6.1.22 | PrvtRapsReceivedCommandType | read-only | The command received on the port belonging to this sub-ring. |
| PRV prvtRapsInstSubRingRcvdInfo | 1.3.6.1.4.1.738.1.7.4.1.6.1.23 | PrvtRapsReceivedInfoType | read-only | The info received on the port belonging to this sub-ring. |
| MAC prvtRapsInstSubRingRcvdNodeId | 1.3.6.1.4.1.738.1.7.4.1.6.1.21 | MacAddress | read-only | The MAC address of the remote R-APS device connected to the port belonging to this sub-ring. |
| T/F prvtRapsInstSubRingRevertiveMode | 1.3.6.1.4.1.738.1.7.4.1.6.1.6 | TruthValue | read-create | Set to 'true' to select revertive behavior for this sub-ring. |
| PRV prvtRapsInstSubRingRole | 1.3.6.1.4.1.738.1.7.4.1.6.1.4 | PrvtRapsRoleType | read-create | The role of the node inside this sub-ring. Must perform shutdown to change this object. |
| ROW prvtRapsInstSubRingRowStatus | 1.3.6.1.4.1.738.1.7.4.1.6.1.2 | RowStatus | read-create | The RowStatus for this sub-ring. |
| T/F prvtRapsInstSubRingShutdown | 1.3.6.1.4.1.738.1.7.4.1.6.1.12 | TruthValue | read-create | Set to 'true' to de-activate this sub-ring. |
| NTF prvtRapsInstSubRingSwitchoverAlarm | 1.3.6.1.4.1.738.1.7.4.0.4 | This trap will be sent by any subring instance when it changes state. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRapsInstSubRingRapsState variable in the notification. | ||
| prvtRapsInstSubRingTable | 1.3.6.1.4.1.738.1.7.4.1.6 | not-accessible | R-APS Instance Sub-ring Table Each entry in this table defines a sub-ring belonging to a R-APS instance. Sub-rings are not available in version 1 mode. | |
| PRV prvtRapsInstSubRingTopPriCmd | 1.3.6.1.4.1.738.1.7.4.1.6.1.18 | PrvtRapsTopPriCmdType | read-only | The received Top Priority Request and Status value for this sub-ring. |
| PRV prvtRapsInstSubRingVcRcvdCmd | 1.3.6.1.4.1.738.1.7.4.1.6.1.26 | PrvtRapsReceivedCommandType | read-only | The command received through the virtual channel belonging to this sub-ring. |
| PRV prvtRapsInstSubRingVcRcvdInfo | 1.3.6.1.4.1.738.1.7.4.1.6.1.27 | PrvtRapsReceivedInfoType | read-only | The info received through the virtual channel belonging to this sub-ring. |
| MAC prvtRapsInstSubRingVcRcvdNodeId | 1.3.6.1.4.1.738.1.7.4.1.6.1.25 | MacAddress | read-only | The MAC address of the remote R-APS device connected through the virtual channel. |
| U32 prvtRapsInstSubRingVirtChanSvc | 1.3.6.1.4.1.738.1.7.4.1.6.1.28 | Unsigned32 | read-create | Configure the virtual channel service for this sub-ring. Only applicable when main ring's control protocol is vpls (prvtRapsInstControlProtocol equals 'vpls'). Must be a service ID from PRVT-SERV-MIB::serviceId. No two sub-rings can use the same service ID for the virtual channel service. |
| PRV prvtRapsInstSubRingVirtChanVlan | 1.3.6.1.4.1.738.1.7.4.1.6.1.5 | PrvtRapsVlanIdType | read-create | Configures the virtual channel VLAN for this sub-ring. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). Must be a VLAN from the prvtRapsInstMonVlanTable. No two sub-rings can use the same VLAN for the virtual channel VLAN. |
| PRV prvtRapsInstSubRingWaitTimer | 1.3.6.1.4.1.738.1.7.4.1.6.1.8 | PrvtRapsWaitTimerType | read-create | The wait-to-restore timer time-out value for this sub-ring. |
| prvtRapsInstTable | 1.3.6.1.4.1.738.1.7.4.1.1 | not-accessible | R-APS Instance table. Each entry in this table defines an instance of a Ring APS. | |
| PRV prvtRapsInstTopPriCmd | 1.3.6.1.4.1.738.1.7.4.1.1.1.18 | PrvtRapsTopPriCmdType | read-only | The received Top Priority Request and Status value for this R-APS instance. |
| PRV prvtRapsInstWaitToBlockTimer | 1.3.6.1.4.1.738.1.7.4.1.1.1.13 | PrvtRapsBlockTimerType | read-only | The wait to block timer time-out value for this sub-ring. |
| PRV prvtRapsInstWaitToRestoreTimer | 1.3.6.1.4.1.738.1.7.4.1.1.1.11 | PrvtRapsWaitTimerType | read-create | The wait-to-restore timer time-out value for this R-APS instance. Only applicable when main ring's control protocol is raps (prvtRapsInstControlProtocol equals 'raps'). |
| prvtRapsMIB | 1.3.6.1.4.1.738.1.7.4 | The SNMP MIB module for Ring Automatic Protection Switching (G.8032). | ||
| prvtRapsMIBNotifications | 1.3.6.1.4.1.738.1.7.4.0 | |||
| prvtRapsMIBObjects | 1.3.6.1.4.1.738.1.7.4.1 | |||
| NTF prvtRapsSwitchoverAlarm | 1.3.6.1.4.1.738.1.7.4.0.2 | This trap will be sent by any instance when it changes state. The management entity receiving the notification can identify the system from the network source address of the notification |
RFC description
Ring Automatic Protection Switching (G.8032) MIB for BATM/Telco Systems switches, managing ring topology redundancy and failover.
Start monitoring carrier Ethernet ring switch (G.8032 ERPS) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.