| OID symbolic | OID numeric | Type | Access | Description |
|---|
| prvtLmgr | 1.3.6.1.4.1.738.1.6.5.4 | | | The MIB module for management of the PRVT-LMGR
product. |
| prvtLmgrObjects | 1.3.6.1.4.1.738.1.6.5.4.1 | | | |
| ADR prvtLsrId | 1.3.6.1.4.1.738.1.6.5.4.1.1 | InetAddressIPv4 | read-write | This object allows LSR Id value to be set. It is needed for unique
identification of LSR instance, from which the packets are sent
through created LDP session.
Although every 32 bit value is valid, it is recommended
the device's loopback ip address to be used.
A value of zero indicates that no LSR ID has been
configured. In this case, the signaling protocol stack
should construct a unique LSR ID from the other
information that is available to it (such as IP
addresses). For example, PRVT-CR-LDP and PRVT-RSVP derive
the LSR ID by taking the 32 low bits of the following
_transport_address_ field, left padding with zeros if
necessary. |
| prvtLmgrLsrEntityTable | 1.3.6.1.4.1.738.1.6.5.4.1.2 | | not-accessible | Each entry represents an instance of the Label Manager.
Each instance is identified by LSR index. |
| prvtLmgrLsrEntityEntry | 1.3.6.1.4.1.738.1.6.5.4.1.2.1 | | not-accessible | Each entry represents a Label Manager entity. |
| PRV prvtlmgrLsrEntityLsrIndex | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.1 | PrvtLmgrIndex | not-accessible | LSR index for this prvtLmgrLsrEntityEntry. This is the
entity index passed in the Label Manager create
parameters. |
| PRV prvtLmgrLsrEntityAdminStatus | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.2 | PrvtLmgrAdminStatus | read-create | Administrative status for Label Manager. When
prvtLmgrLsrEntityRowStatus is 'active' and
prvtLmgrLsrEntityAdminStatus is 'up' Label Manager is
active and only these two fields and
prvtLmgrLsrEntityMinLsiBuffers can be modified. |
| PRV prvtLmgrLsrEntityOperStatus | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.3 | PrvtLmgrOperStatus | read-only | The current operational status of the Label Manager
entity. |
| ROW prvtLmgrLsrEntityRowStatus | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.4 | RowStatus | read-create | Row status for the Label Manager table entry, used to
create and destroy table entries. When
prvtLmgrLsrEntityRowStatus is 'active' and
prvtLmgrLsrEntityAdminStatus is 'up' Label Manager is
active and only these two fields and
prvtLmgrLsrEntityMinLsiBuffers can be modified. |
| U32 prvtLmgrLsrEntityMinLsiBuffers | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.5 | Unsigned32 | read-create | Minimum number of buffers to allocate for Label Switch
Interface requests. This number includes any buffers sent
to the Label Switch Controller and awaiting a response. |
| U32 prvtLmgrLsrEntityMaxLsiBuffers | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.6 | Unsigned32 | read-create | Maximum number of buffers to allocate for Label Switch
Interface requests. A value of 0 means no maximum,
otherwise this value must equal or exceed the minimum
buffer count. |
| PRV prvtLmgrLscStatus | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.7 | PrvtLmgrPartnerStatus | read-only | Diagnostic field providing information about the status
of the Label Switch Controller as seen by Label Manager. |
| U32 prvtLmgrLdbCount | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.8 | Unsigned32 | read-only | Diagnostic field providing information about the number
of active interfaces between Label Manager and the its
Label Database Interface users (PRVT-TEMIB and PRVT-RSVP). |
| U32 prvtLmgrLsrEntityLsrId | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.9 | Unsigned32 | read-only | An ID that uniquely identifies this LSR within the
network.
The LSR ID is typically derived from one of the LSR's IP
addresses. It may be used for path vector based loop
detection if the signaling protocol in use implements
that.
A value of zero indicates that no LSR ID has been
configured. In this case, the signaling protocol stack
should construct a unique LSR ID from the other
information that is available to it (such as IP
addresses). For example, PRVT-CR-LDP and PRVT-RSVP derive
the LSR ID by taking the 32 low bits of the following
_transport_address_ field, left padding with zeros if
necessary.
The LSR ID is only used to identify this LSR on IPv4
networks. See dcLmgrLsrEntityIpv6TranAddr for equivalent
function for use in IPv6 networks. |
| IPt prvtLmgrLsrEntityTranAddrType | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.10 | InetAddressType | read-create | The type of the internetwork layer address used as the
transport address. Currently this must be IPv4. See
dcLmgrLsrEntityIpv6TranAddr, below, for the equivalent
field for use in IPv6 networks.
The transport address is used by LDP as the source
transport address for LDP Hello messages for the global
(per-platform) label space.
The transport address is used by RSVP as the source
address for messages originating on unnumbered interfaces.
This object indicates how the value of
mplsLdpEntityTransAddr is to be interpreted. |
| U32 prvtLmgrLsrEntityTranAddrLen | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.11 | Unsigned32 | read-create | The length of the internetwork layer address used as the
transport address for LDP Hello messages in the global
label space and for messages originating on unnumbered
interfaces in RSVP. Currently this must be an IPv4
address.
This object indicates how many elements of the
mplsLdpEntityTransAddr array are valid. This value must
not exceed _LMGR_LSR_ADDR_LEN_. |
| IP prvtLmgrLsrEntityTranAddr | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.12 | InetAddress | read-create | The value of the internetwork layer address used as the
transport address for LDP Hello messages in the global
label space and for messages originating on unnumbered
interfaces in RSVP.
This must be an IPv4 address. See
dcLmgrLsrEntityIpv6TranAddr, below, for the equivalent
field for use in IPv6 networks.
If the transport address is not set, then _lsr_id_ must be
set to zero. In this case, the transport address and LSR
ID are taken from an address on the Interface Information
Interface. |
| PRV prvtLmgrLsrEntityControlMode | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.13 | PrvtLmgrControlModes | read-create | The LSP control mode that this LSR should adopt.
This field is only used by Label Manager in systems where
it supports LDP and/or CR-LDP. |
| T/F prvtLmgrLsrEntityMergeLsps | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.14 | TruthValue | read-create | Whether this LSR should aim to merge LSPs, where permitted
by the underlying hardware.
This field is only used by Label Manager in systems where
it supports LDP and/or CR-LDP. |
| T/F prvtLmgrLsrEntityLoopDetection | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.15 | TruthValue | read-create | Whether this LSR should perform loop detection.
This field is only used by Label Manager in systems where
it supports LDP and/or CR-LDP. |
| T/F prvtLmgrLsrEntityPerformGrouping | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.16 | TruthValue | read-create | Whether Label Manager should perform LSP grouping on
behalf of the LDBI user. This field is currently only
used for systems supporting RSVP. |
| T/F prvtLmgrLsrAutoStaticLsps | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.17 | TruthValue | read-create | Whether Label Manager should automatically activate or
deactivate static LSPs when the interfaces on which they
depend become active or inactive. |
| T/F prvtLmgrLsrDisplayPhpXCs | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.18 | TruthValue | read-create | Whether Label Manager should display the virtual cross
connects its sets up at the Egress node of Implicit Null
and Explicit Null LSPs in the mplsXcTable. These cross
connects do not represent real switch programming, but do
show the prescence of such LSPs, and correspond to the
entries in the mplsTunnelTable for theses types of LSP. |
| IP prvtLmgrLsrEntityIpv6TranAddr | 1.3.6.1.4.1.738.1.6.5.4.1.2.1.19 | InetAddress | read-create | The value of the internetwork address used for messages
originating on unnumbered interfaces in RSVP in an IPv6
network.
This value also uniquely identifies this LSR within an
IPv6 network.
If this address is not set, the IPv6 transport address is
taken from an address on the Interface Information
Interface.
A length value of zero indicates that no IPv6 transport
address has been configured. In this case, if IPv6
support is configured, the signaling protocol stack should
use an IPv6 address configured to the signaling stack over
the Interface Information Interface that is flagged as
suitable for use as a stable address. |
| prvtLmgrLsrLspXcTable | 1.3.6.1.4.1.738.1.6.5.4.1.3 | | not-accessible | Each entry represents an instance of an LSP
cross-conect between a single in-segment and a
single out-segment. |
| prvtLmgrLsrLspXcEntry | 1.3.6.1.4.1.738.1.6.5.4.1.3.1 | | not-accessible | Each entry represents an LSP cross connect. |
| U32 prvtLmgrLsrLspXcIndex | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.2 | Unsigned32 | not-accessible | XC index for this prvtLmgrLsrLspXc. This is the XC index
assigned by Label Manager for the LSP. |
| U32 prvtLmgrLsrLspInSegIndex | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.3 | Unsigned32 | not-accessible | Index for the in segment. This is the index assigned
by Label Manager for the in segment. |
| U32 prvtLmgrLsrLspInSegIfIndex | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.4 | Unsigned32 | read-only | If index for the in segment. This is the If index
specified on setting up the in segment. |
| U32 prvtLmgrLsrLspInSegLabel | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.5 | Unsigned32 | read-only | Top label for the in segment. This is the Label assigned
by Label Manager Label Library for the in segment. |
| U32 prvtLmgrLsrLspOutSegIndex | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.6 | Unsigned32 | not-accessible | Index for the out segment. This is the index assigned
by Label Manager for the out segment. |
| U32 prvtLmgrLsrLspOutSegIfIndex | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.7 | Unsigned32 | read-only | Interface Index for the out segment. This is the
interface index specified when setting up the out segment. |
| U32 prvtLmgrLsrLspOutSegLabel | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.8 | Unsigned32 | read-only | Top label for the out segment. This is the label
specified by the remote LSR for the out segment. |
| ADR prvtLmgrLsrLspOutSegNextHopAddr | 1.3.6.1.4.1.738.1.6.5.4.1.3.1.9 | InetAddressIPv4 | read-only | Next hop address for the out segment. This is the address
specified by the remote LSR for the out segment. |
| prvtLmgrConformance | 1.3.6.1.4.1.738.1.6.5.4.2 | | | |
| prvtLmgrCompliances | 1.3.6.1.4.1.738.1.6.5.4.2.1 | | | |
| prvtLmgrCompliance | 1.3.6.1.4.1.738.1.6.5.4.2.1.1 | | | The compliance statement for the PRVT-LMGR product. |
| prvtLmgrGroups | 1.3.6.1.4.1.738.1.6.5.4.2.2 | | | |
| prvtLmgrEntityGroup | 1.3.6.1.4.1.738.1.6.5.4.2.2.2 | | | Label Manager Entity Objects. |
| prvtLmgrMiscGroup | 1.3.6.1.4.1.738.1.6.5.4.2.2.3 | | | Miscellaneous Non-Mandatory Objects. |
