All MIBs › OSPFV3-MIB-JUNIPER
Organization: IETF OSPF Working Group
Last Updated: 2011-03-30
Category: Routing
Description: Provides Juniper Networks private OSPFv3 management extensions for IPv6 routing configuration and status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is OSPFV3-MIB-JUNIPER?
OSPFV3-MIB-JUNIPER is Juniper Networks' private-enterprise adaptation of the standard OSPFv3 MIB, used to manage and monitor OSPF version 3 routing (the IPv6-capable variant of OSPF) on Juniper routing platforms. No sample runtime objects were captured for this module in this dataset, but per its stated scope it covers OSPFv3 protocol/process configuration, area and interface settings, and neighbor/adjacency status for IPv6 routing. In monitoring terms this is a software/protocol-status MIB rather than a hardware one - it would be used to check neighbor adjacency state, area configuration consistency, and routing process health. It explicitly builds on and depends on the IETF's standard OSPFv3 MIB (as referenced in the RFC placeholder in its description), adding Juniper-private extensions on top. It's deployed on Juniper routers and switches running OSPFv3 for IPv6 unicast routing, polled by network management systems tracking routing protocol health. Engineers implementing or auditing this functionality typically reference the OSPFV3-MIB-JUNIPER RFC/standard documentation for the authoritative specification.
IPNetwork Monitor allows you to monitor SNMP objects defined in OSPFV3-MIB-JUNIPER. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper Networks router or switch running OSPFv3
Monitoring Examples
Because sample_objects is empty for this module, no concrete object names can be cited from this dataset; per its stated purpose, a typical use would be polling OSPFv3 neighbor and interface state (as extended from the base OSPFv3 MIB) to detect adjacency flaps or area misconfiguration, but this specific scenario cannot be grounded in named objects here.
What Can Be Monitored
- OSPFv3 neighbor adjacency state
- OSPFv3 interface configuration
- OSPF area status
- routing process state
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressPrefixLength | |
| InetAddressType |
From OSPF-MIB
| BigMetric | |
| DesignatedRouterPriority | |
| HelloRange | |
| Metric | |
| Status |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| mib-2 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| jnxOspfv3MIB | 1.3.6.1.4.1.2636.5.4.1 | The MIB module for OSPF version 3. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices. | ||
| jnxOspfv3Notifications | 1.3.6.1.4.1.2636.5.4.1.0 | |||
| NTF jnxOspfv3VirtIfStateChange | 1.3.6.1.4.1.2636.5.4.1.0.1 | An ospfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point). | ||
| NTF jnxOspfv3NbrStateChange | 1.3.6.1.4.1.2636.5.4.1.0.2 | An ospfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange. | ||
| NTF jnxOspfv3VirtNbrStateChange | 1.3.6.1.4.1.2636.5.4.1.0.3 | An ospfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full). | ||
| NTF jnxOspfv3IfConfigError | 1.3.6.1.4.1.2636.5.4.1.0.4 | An ospfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming. | ||
| NTF jnxOspfv3VirtIfConfigError | 1.3.6.1.4.1.2636.5.4.1.0.5 | An ospfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming. | ||
| NTF jnxOspfv3IfRxBadPacket | 1.3.6.1.4.1.2636.5.4.1.0.6 | An ospfv3IfRxBadPacket notification signifies that an ospfv3 packet that cannot be parsed has been received on a non-virtual interface. | ||
| NTF jnxOspfv3VirtIfRxBadPacket | 1.3.6.1.4.1.2636.5.4.1.0.7 | An ospfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface. | ||
| NTF jnxOspfv3LsdbOverflow | 1.3.6.1.4.1.2636.5.4.1.0.8 | An ospfv3LsdbOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ospfv3ExtAreaLsdbLimit. | ||
| NTF jnxOspfv3LsdbApproachingOverflow | 1.3.6.1.4.1.2636.5.4.1.0.9 | An ospfv3LsdbApproachingOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ninety percent of ospfv3ExtAreaLsdbLimit. | ||
| NTF jnxOspfv3IfStateChange | 1.3.6.1.4.1.2636.5.4.1.0.10 | An ospfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup). | ||
| NTF jnxOspfv3NssaTranslatorStatusChange | 1.3.6.1.4.1.2636.5.4.1.0.11 | An ospfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per area basis. | ||
| NTF jnxOspfv3RestartStatusChange | 1.3.6.1.4.1.2636.5.4.1.0.12 | An ospfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes. | ||
| NTF jnxOspfv3NbrRestartHelperStatusChange | 1.3.6.1.4.1.2636.5.4.1.0.13 | An ospfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor. | ||
| NTF jnxOspfv3VirtNbrRestartHelperStatusChange | 1.3.6.1.4.1.2636.5.4.1.0.14 | An ospfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor. | ||
| jnxOspfv3Objects | 1.3.6.1.4.1.2636.5.4.1.1 | |||
| jnxOspfv3GeneralGroup | 1.3.6.1.4.1.2636.5.4.1.1.1 | |||
| JNX jnxOspfv3RouterId | 1.3.6.1.4.1.2636.5.4.1.1.1.1 | JnxOspfv3RouterIdTc | read-write | A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router. |
| STA jnxOspfv3AdminStat | 1.3.6.1.4.1.2636.5.4.1.1.1.2 | Status | read-write | The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces. |
| INT jnxOspfv3VersionNumber | 1.3.6.1.4.1.2636.5.4.1.1.1.3 | INTEGER | read-only | The version number of OSPF for IPv6 is 3. |
| T/F jnxOspfv3AreaBdrRtrStatus | 1.3.6.1.4.1.2636.5.4.1.1.1.4 | TruthValue | read-only | A flag to note whether this router is an area border router. |
| T/F jnxOspfv3ASBdrRtrStatus | 1.3.6.1.4.1.2636.5.4.1.1.1.5 | TruthValue | read-write | A flag to note whether this router is configured as an Autonomous System border router. |
| G32 jnxOspfv3AsScopeLsaCount | 1.3.6.1.4.1.2636.5.4.1.1.1.6 | Gauge32 | read-only | The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database. |
| I32 jnxOspfv3AsScopeLsaCksumSum | 1.3.6.1.4.1.2636.5.4.1.1.1.7 | Integer32 | read-only | The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers. |
| C32 jnxOspfv3OriginateNewLsas | 1.3.6.1.4.1.2636.5.4.1.1.1.8 | Counter32 | read-only | The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA. |
| C32 jnxOspfv3RxNewLsas | 1.3.6.1.4.1.2636.5.4.1.1.1.9 | Counter32 | read-only | The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements. |
| G32 jnxOspfv3ExtLsaCount | 1.3.6.1.4.1.2636.5.4.1.1.1.10 | Gauge32 | read-only | The number of External(LS type 0x4005) in the link state database |
| I32 jnxOspfv3ExtAreaLsdbLimit | 1.3.6.1.4.1.2636.5.4.1.1.1.11 | Integer32 | read-write | The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. Ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded). |
| BIT jnxOspfv3MulticastExtensions | 1.3.6.1.4.1.2636.5.4.1.1.1.12 | Bits | read-write | A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multicast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area multicast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Autonomous Systems (called inter-AS multicast routing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared. |
| U32 jnxOspfv3ExitOverflowInterval | 1.3.6.1.4.1.2636.5.4.1.1.1.13 | Unsigned32 | read-write | The number of seconds that, after entering Overflow State, a router will attempt to leave Overflow State. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow State until restarted. |
| T/F jnxOspfv3DemandExtensions | 1.3.6.1.4.1.2636.5.4.1.1.1.14 | TruthValue | read-write | The router's support for demand routing. |
| U32 jnxOspfv3ReferenceBandwidth | 1.3.6.1.4.1.2636.5.4.1.1.1.15 | Unsigned32 | read-write | Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS) |
| INT jnxOspfv3RestartSupport | 1.3.6.1.4.1.2636.5.4.1.1.1.16 | INTEGER | read-write | The router's support for OSPF Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts. |
| NUM jnxOspfv3RestartInterval | 1.3.6.1.4.1.2636.5.4.1.1.1.17 | JnxOspfv3UpToRefreshIntervalTc | read-write | Configured OSPF Graceful restart timeout interval. |
| INT jnxOspfv3RestartStatus | 1.3.6.1.4.1.2636.5.4.1.1.1.18 | INTEGER | read-only | The current status of OSPF Graceful restart capability. |
| NUM jnxOspfv3RestartAge | 1.3.6.1.4.1.2636.5.4.1.1.1.19 | JnxOspfv3UpToRefreshIntervalTc | read-only | Remaining time in current OSPF Graceful restart interval. |
| INT jnxOspfv3RestartExitRc | 1.3.6.1.4.1.2636.5.4.1.1.1.20 | INTEGER | read-only | Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change. |
| T/F jnxOspfv3NotificationEnable | 1.3.6.1.4.1.2636.5.4.1.1.1.21 | TruthValue | read-write | If this object is set to true(1), then it enables the generation of OSPFv3 Notifications. If it is set to false(2), these notifications are not generated. Configured values MUST survive an agent reboot. |
| jnxOspfv3AreaTable | 1.3.6.1.4.1.2636.5.4.1.1.2 | not-accessible | Information describing the configured parameters and cumulative statistics of the router's attached areas. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3AreaEntry | 1.3.6.1.4.1.2636.5.4.1.1.2.1 | not-accessible | Information describing the configured parameters and cumulative statistics of one of the router's attached areas. | |
| JNX jnxOspfv3AreaId | 1.3.6.1.4.1.2636.5.4.1.1.2.1.1 | JnxOspfv3AreaIdTc | not-accessible | A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone. |
| INT jnxOspfv3ImportAsExtern | 1.3.6.1.4.1.2636.5.4.1.1.2.1.2 | INTEGER | read-create | Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope |
| C32 jnxOspfv3AreaSpfRuns | 1.3.6.1.4.1.2636.5.4.1.1.2.1.3 | Counter32 | read-only | The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm. |
| G32 jnxOspfv3AreaBdrRtrCount | 1.3.6.1.4.1.2636.5.4.1.1.2.1.4 | Gauge32 | read-only | The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass. |
| G32 jnxOspfv3AreaAsBdrRtrCount | 1.3.6.1.4.1.2636.5.4.1.1.2.1.5 | Gauge32 | read-only | The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass. |
| G32 jnxOspfv3AreaScopeLsaCount | 1.3.6.1.4.1.2636.5.4.1.1.2.1.6 | Gauge32 | read-only | The total number of Area-Scope link state advertisements in this area's link state database. |
| I32 jnxOspfv3AreaScopeLsaCksumSum | 1.3.6.1.4.1.2636.5.4.1.1.2.1.7 | Integer32 | read-only | The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers. |
| INT jnxOspfv3AreaSummary | 1.3.6.1.4.1.2636.5.4.1.1.2.1.8 | INTEGER | read-create | The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs. |
| ROW jnxOspfv3AreaStatus | 1.3.6.1.4.1.2636.5.4.1.1.2.1.9 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| BIG jnxOspfv3StubMetric | 1.3.6.1.4.1.2636.5.4.1.1.2.1.10 | BigMetric | read-create | The metric value advertised for the default route into Stub and NSSA areas. |
| INT jnxOspfv3AreaNssaTranslatorRole | 1.3.6.1.4.1.2636.5.4.1.1.2.1.11 | INTEGER | read-create | Indicates an NSSA Border router's ability to perform NSSA translation of NSSA-LSAs into AS-External-LSAs. |
| INT jnxOspfv3AreaNssaTranslatorState | 1.3.6.1.4.1.2636.5.4.1.1.2.1.12 | INTEGER | read-only | Indicates if and how an NSSA Border router is performing NSSA translation of NSSA-LSAs into AS-External-LSA's. When this object is set to enabled, the NSSA Border router's ospfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating NSSA-LSA's into AS-External-LSA's. When this object is set to disabled, a candidate NSSA Border router is NOT translating NSSA-LSA's into AS-External-LSA's. |
| U32 jnxOspfv3AreaNssaTranslatorStabInt | 1.3.6.1.4.1.2636.5.4.1.1.2.1.13 | Unsigned32 | read-create | The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties. |
| C32 jnxOspfv3AreaNssaTranslatorEvents | 1.3.6.1.4.1.2636.5.4.1.1.2.1.14 | Counter32 | read-only | Indicates the number of Translator State changes that have occurred since the last boot-up. |
| INT jnxOspfv3AreaStubMetricType | 1.3.6.1.4.1.2636.5.4.1.1.2.1.15 | INTEGER | read-create | This variable displays the type of metric advertised as a default route. |
| jnxOspfv3AsLsdbTable | 1.3.6.1.4.1.2636.5.4.1.1.3 | not-accessible | The OSPFv3 Process's AS-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3AsLsdbEntry | 1.3.6.1.4.1.2636.5.4.1.1.3.1 | not-accessible | A single AS-Scope Link State Advertisement. | |
| U32 jnxOspfv3AsLsdbType | 1.3.6.1.4.1.2636.5.4.1.1.3.1.1 | Unsigned32 | not-accessible | The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database. |
| JNX jnxOspfv3AsLsdbRouterId | 1.3.6.1.4.1.2636.5.4.1.1.3.1.2 | JnxOspfv3RouterIdTc | not-accessible | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| U32 jnxOspfv3AsLsdbLsid | 1.3.6.1.4.1.2636.5.4.1.1.3.1.3 | Unsigned32 | not-accessible | The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. |
| I32 jnxOspfv3AsLsdbSequence | 1.3.6.1.4.1.2636.5.4.1.1.3.1.4 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 jnxOspfv3AsLsdbAge | 1.3.6.1.4.1.2636.5.4.1.1.3.1.5 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 jnxOspfv3AsLsdbChecksum | 1.3.6.1.4.1.2636.5.4.1.1.3.1.6 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT jnxOspfv3AsLsdbAdvertisement | 1.3.6.1.4.1.2636.5.4.1.1.3.1.7 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. |
| T/F jnxOspfv3AsLsdbTypeKnown | 1.3.6.1.4.1.2636.5.4.1.1.3.1.8 | TruthValue | read-only | Indicates whether the LSA type is recognized by this Router. |
| jnxOspfv3AreaLsdbTable | 1.3.6.1.4.1.2636.5.4.1.1.4 | not-accessible | The OSPFv3 Process's Area-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3AreaLsdbEntry | 1.3.6.1.4.1.2636.5.4.1.1.4.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| JNX jnxOspfv3AreaLsdbAreaId | 1.3.6.1.4.1.2636.5.4.1.1.4.1.1 | JnxOspfv3AreaIdTc | not-accessible | The 32-bit identifier of the Area from which the LSA was received. |
| U32 jnxOspfv3AreaLsdbType | 1.3.6.1.4.1.2636.5.4.1.1.4.1.2 | Unsigned32 | not-accessible | The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database. |
| JNX jnxOspfv3AreaLsdbRouterId | 1.3.6.1.4.1.2636.5.4.1.1.4.1.3 | JnxOspfv3RouterIdTc | not-accessible | The 32-bit number that uniquely identifies the originating router in the Autonomous System. |
| U32 jnxOspfv3AreaLsdbLsid | 1.3.6.1.4.1.2636.5.4.1.1.4.1.4 | Unsigned32 | not-accessible | The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. |
| I32 jnxOspfv3AreaLsdbSequence | 1.3.6.1.4.1.2636.5.4.1.1.4.1.5 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 jnxOspfv3AreaLsdbAge | 1.3.6.1.4.1.2636.5.4.1.1.4.1.6 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 jnxOspfv3AreaLsdbChecksum | 1.3.6.1.4.1.2636.5.4.1.1.4.1.7 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT jnxOspfv3AreaLsdbAdvertisement | 1.3.6.1.4.1.2636.5.4.1.1.4.1.8 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. |
| T/F jnxOspfv3AreaLsdbTypeKnown | 1.3.6.1.4.1.2636.5.4.1.1.4.1.9 | TruthValue | read-only | Indicates whether the LSA type is recognized by this Router. |
| jnxOspfv3LinkLsdbTable | 1.3.6.1.4.1.2636.5.4.1.1.5 | not-accessible | The OSPFv3 Process's Link-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3LinkLsdbEntry | 1.3.6.1.4.1.2636.5.4.1.1.5.1 | not-accessible | A single Link-Scope Link State Advertisement. | |
| NUM jnxOspfv3LinkLsdbIfIndex | 1.3.6.1.4.1.2636.5.4.1.1.5.1.1 | InterfaceIndex | not-accessible | The identifier of the link from which the LSA was received. |
| JNX jnxOspfv3LinkLsdbIfInstId | 1.3.6.1.4.1.2636.5.4.1.1.5.1.2 | JnxOspfv3IfInstIdTc | not-accessible | The identifier of the interface instance from which the LSA was received. |
| U32 jnxOspfv3LinkLsdbType | 1.3.6.1.4.1.2636.5.4.1.1.5.1.3 | Unsigned32 | not-accessible | The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database. |
| JNX jnxOspfv3LinkLsdbRouterId | 1.3.6.1.4.1.2636.5.4.1.1.5.1.4 | JnxOspfv3RouterIdTc | not-accessible | The 32 bit number that uniquely identifies the originating router in the Autonomous System. |
| U32 jnxOspfv3LinkLsdbLsid | 1.3.6.1.4.1.2636.5.4.1.1.5.1.5 | Unsigned32 | not-accessible | The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. |
| I32 jnxOspfv3LinkLsdbSequence | 1.3.6.1.4.1.2636.5.4.1.1.5.1.6 | Integer32 | read-only | The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. |
| I32 jnxOspfv3LinkLsdbAge | 1.3.6.1.4.1.2636.5.4.1.1.5.1.7 | Integer32 | read-only | This field is the age of the link state advertisement in seconds. |
| I32 jnxOspfv3LinkLsdbChecksum | 1.3.6.1.4.1.2636.5.4.1.1.5.1.8 | Integer32 | read-only | This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. |
| OCT jnxOspfv3LinkLsdbAdvertisement | 1.3.6.1.4.1.2636.5.4.1.1.5.1.9 | OCTET STRING | read-only | The entire Link State Advertisement, including its header. |
| T/F jnxOspfv3LinkLsdbTypeKnown | 1.3.6.1.4.1.2636.5.4.1.1.5.1.10 | TruthValue | read-only | Indicates whether the LSA type is recognized by this Router. |
| jnxOspfv3HostTable | 1.3.6.1.4.1.2636.5.4.1.1.6 | not-accessible | The list of Hosts, and their metrics, that the router will advertise as host routes. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3HostEntry | 1.3.6.1.4.1.2636.5.4.1.1.6.1 | not-accessible | A metric to be advertised when a given host is reachable. | |
| IPt jnxOspfv3HostAddressType | 1.3.6.1.4.1.2636.5.4.1.1.6.1.1 | InetAddressType | not-accessible | The address type of ospfv3HostAddress. Only IPv6 addresses without zone index are expected. |
| IP jnxOspfv3HostAddress | 1.3.6.1.4.1.2636.5.4.1.1.6.1.2 | InetAddress | not-accessible | The IPv6 Address of the Host. Must be a Global address. |
| MET jnxOspfv3HostMetric | 1.3.6.1.4.1.2636.5.4.1.1.6.1.3 | Metric | read-create | The Metric to be advertised. |
| ROW jnxOspfv3HostStatus | 1.3.6.1.4.1.2636.5.4.1.1.6.1.4 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| JNX jnxOspfv3HostAreaID | 1.3.6.1.4.1.2636.5.4.1.1.6.1.5 | JnxOspfv3AreaIdTc | read-create | The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 interface is in, or Area 0 |
| jnxOspfv3IfTable | 1.3.6.1.4.1.2636.5.4.1.1.7 | not-accessible | The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3IfEntry | 1.3.6.1.4.1.2636.5.4.1.1.7.1 | not-accessible | The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3. | |
| NUM jnxOspfv3IfIndex | 1.3.6.1.4.1.2636.5.4.1.1.7.1.1 | InterfaceIndex | not-accessible | The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured. |
| JNX jnxOspfv3IfInstId | 1.3.6.1.4.1.2636.5.4.1.1.7.1.2 | JnxOspfv3IfInstIdTc | not-accessible | Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only. |
| JNX jnxOspfv3IfAreaId | 1.3.6.1.4.1.2636.5.4.1.1.7.1.3 | JnxOspfv3AreaIdTc | read-create | A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone. |
| INT jnxOspfv3IfType | 1.3.6.1.4.1.2636.5.4.1.1.7.1.4 | INTEGER | read-create | The OSPFv3 interface type. |
| STA jnxOspfv3IfAdminStat | 1.3.6.1.4.1.2636.5.4.1.1.7.1.5 | Status | read-create | The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3. |
| DES jnxOspfv3IfRtrPriority | 1.3.6.1.4.1.2636.5.4.1.1.7.1.6 | DesignatedRouterPriority | read-create | The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker. |
| NUM jnxOspfv3IfTransitDelay | 1.3.6.1.4.1.2636.5.4.1.1.7.1.7 | JnxOspfv3UpToRefreshIntervalTc | read-create | The estimated number of seconds it takes to transmit a link state update packet over this interface. |
| NUM jnxOspfv3IfRetransInterval | 1.3.6.1.4.1.2636.5.4.1.1.7.1.8 | JnxOspfv3UpToRefreshIntervalTc | read-create | The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. |
| HEL jnxOspfv3IfHelloInterval | 1.3.6.1.4.1.2636.5.4.1.1.7.1.9 | HelloRange | read-create | The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network. |
| NUM jnxOspfv3IfRtrDeadInterval | 1.3.6.1.4.1.2636.5.4.1.1.7.1.10 | JnxOspfv3DeadIntRangeTc | read-create | The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. |
| U32 jnxOspfv3IfPollInterval | 1.3.6.1.4.1.2636.5.4.1.1.7.1.11 | Unsigned32 | read-create | The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor. |
| INT jnxOspfv3IfState | 1.3.6.1.4.1.2636.5.4.1.1.7.1.12 | INTEGER | read-only | The OSPFv3 Interface State. |
| JNX jnxOspfv3IfDesignatedRouter | 1.3.6.1.4.1.2636.5.4.1.1.7.1.13 | JnxOspfv3RouterIdTc | read-only | The Router ID of the Designated Router. |
| JNX jnxOspfv3IfBackupDesignatedRouter | 1.3.6.1.4.1.2636.5.4.1.1.7.1.14 | JnxOspfv3RouterIdTc | read-only | The Router ID of the Backup Designated Router. |
| C32 jnxOspfv3IfEvents | 1.3.6.1.4.1.2636.5.4.1.1.7.1.15 | Counter32 | read-only | The number of times this OSPF interface has changed its state, or an error has occurred. |
| ROW jnxOspfv3IfStatus | 1.3.6.1.4.1.2636.5.4.1.1.7.1.16 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| INT jnxOspfv3IfMulticastForwarding | 1.3.6.1.4.1.2636.5.4.1.1.7.1.17 | INTEGER | read-create | The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effectively disables all multicast forwarding. |
| T/F jnxOspfv3IfDemand | 1.3.6.1.4.1.2636.5.4.1.1.7.1.18 | TruthValue | read-create | Indicates whether Demand OSPFv3 procedures (hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface. |
| MET jnxOspfv3IfMetricValue | 1.3.6.1.4.1.2636.5.4.1.1.7.1.19 | Metric | read-create | The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the ospfv3ReferenceBandwidth object. |
| G32 jnxOspfv3IfLinkScopeLsaCount | 1.3.6.1.4.1.2636.5.4.1.1.7.1.20 | Gauge32 | read-only | The total number of Link-Scope link state advertisements in this link's link state database. |
| I32 jnxOspfv3IfLinkLsaCksumSum | 1.3.6.1.4.1.2636.5.4.1.1.7.1.21 | Integer32 | read-only | The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers. |
| T/F jnxOspfv3IfDemandNbrProbe | 1.3.6.1.4.1.2636.5.4.1.1.7.1.22 | TruthValue | read-create | Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default. |
| U32 jnxOspfv3IfDemandNbrProbeRetxLimit | 1.3.6.1.4.1.2636.5.4.1.1.7.1.23 | Unsigned32 | read-create | The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down. |
| U32 jnxOspfv3IfDemandNbrProbeInterval | 1.3.6.1.4.1.2636.5.4.1.1.7.1.24 | Unsigned32 | read-create | Defines how often the neighbor will be probed. |
| jnxOspfv3VirtIfTable | 1.3.6.1.4.1.2636.5.4.1.1.8 | not-accessible | Information about this router's virtual interfaces. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3VirtIfEntry | 1.3.6.1.4.1.2636.5.4.1.1.8.1 | not-accessible | Information about a single Virtual Interface. | |
| JNX jnxOspfv3VirtIfAreaId | 1.3.6.1.4.1.2636.5.4.1.1.8.1.1 | JnxOspfv3AreaIdTc | not-accessible | The Transit Area that the Virtual Link traverses. By definition, this is not Area 0 |
| JNX jnxOspfv3VirtIfNeighbor | 1.3.6.1.4.1.2636.5.4.1.1.8.1.2 | JnxOspfv3RouterIdTc | not-accessible | The Router ID of the Virtual Neighbor. |
| NUM jnxOspfv3VirtIfIndex | 1.3.6.1.4.1.2636.5.4.1.1.8.1.3 | InterfaceIndex | read-only | The local interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs. |
| JNX jnxOspfv3VirtIfInstId | 1.3.6.1.4.1.2636.5.4.1.1.8.1.4 | JnxOspfv3IfInstIdTc | read-create | Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only. |
| NUM jnxOspfv3VirtIfTransitDelay | 1.3.6.1.4.1.2636.5.4.1.1.8.1.5 | JnxOspfv3UpToRefreshIntervalTc | read-create | The estimated number of seconds it takes to transmit a link state update packet over this interface. |
| NUM jnxOspfv3VirtIfRetransInterval | 1.3.6.1.4.1.2636.5.4.1.1.8.1.6 | JnxOspfv3UpToRefreshIntervalTc | read-create | The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time. |
| HEL jnxOspfv3VirtIfHelloInterval | 1.3.6.1.4.1.2636.5.4.1.1.8.1.7 | HelloRange | read-create | The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor. |
| NUM jnxOspfv3VirtIfRtrDeadInterval | 1.3.6.1.4.1.2636.5.4.1.1.8.1.8 | JnxOspfv3DeadIntRangeTc | read-create | The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor. |
| INT jnxOspfv3VirtIfState | 1.3.6.1.4.1.2636.5.4.1.1.8.1.9 | INTEGER | read-only | ospf virtual interface states. The same encoding as the ospfV3IfTable is used. |
| C32 jnxOspfv3VirtIfEvents | 1.3.6.1.4.1.2636.5.4.1.1.8.1.10 | Counter32 | read-only | The number of state changes or error events on this Virtual Link |
| ROW jnxOspfv3VirtIfStatus | 1.3.6.1.4.1.2636.5.4.1.1.8.1.11 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| G32 jnxOspfv3VirtIfLinkScopeLsaCount | 1.3.6.1.4.1.2636.5.4.1.1.8.1.12 | Gauge32 | read-only | The total number of Link-Scope link state advertisements in this virtual link's link state database. |
| I32 jnxOspfv3VirtIfLinkLsaCksumSum | 1.3.6.1.4.1.2636.5.4.1.1.8.1.13 | Integer32 | read-only | The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers. |
| jnxOspfv3NbrTable | 1.3.6.1.4.1.2636.5.4.1.1.9 | not-accessible | A table of non-virtual neighbor information. | |
| jnxOspfv3NbrEntry | 1.3.6.1.4.1.2636.5.4.1.1.9.1 | not-accessible | The information regarding a single neighbor. | |
| NUM jnxOspfv3NbrIfIndex | 1.3.6.1.4.1.2636.5.4.1.1.9.1.1 | InterfaceIndex | not-accessible | The local link ID of the link over which the neighbor can be reached. |
| JNX jnxOspfv3NbrIfInstId | 1.3.6.1.4.1.2636.5.4.1.1.9.1.2 | JnxOspfv3IfInstIdTc | not-accessible | Interface instance over which the neighbor can be reached. This ID has local link significance only. |
| JNX jnxOspfv3NbrRtrId | 1.3.6.1.4.1.2636.5.4.1.1.9.1.3 | JnxOspfv3RouterIdTc | not-accessible | A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. |
| IPt jnxOspfv3NbrAddressType | 1.3.6.1.4.1.2636.5.4.1.1.9.1.4 | InetAddressType | read-only | The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected. |
| IP jnxOspfv3NbrAddress | 1.3.6.1.4.1.2636.5.4.1.1.9.1.5 | InetAddress | read-only | The IPv6 address of the neighbor associated with the local link. |
| I32 jnxOspfv3NbrOptions | 1.3.6.1.4.1.2636.5.4.1.1.9.1.6 | Integer32 | read-only | A Bit Mask corresponding to the neighbor's options field. |
| DES jnxOspfv3NbrPriority | 1.3.6.1.4.1.2636.5.4.1.1.9.1.7 | DesignatedRouterPriority | read-only | The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network. |
| INT jnxOspfv3NbrState | 1.3.6.1.4.1.2636.5.4.1.1.9.1.8 | INTEGER | read-only | The State of the relationship with this Neighbor. |
| C32 jnxOspfv3NbrEvents | 1.3.6.1.4.1.2636.5.4.1.1.9.1.9 | Counter32 | read-only | The number of times this neighbor relationship has changed state, or an error has occurred. |
| G32 jnxOspfv3NbrLsRetransQLen | 1.3.6.1.4.1.2636.5.4.1.1.9.1.10 | Gauge32 | read-only | The current length of the retransmission queue. |
| T/F jnxOspfv3NbrHelloSuppressed | 1.3.6.1.4.1.2636.5.4.1.1.9.1.11 | TruthValue | read-only | Indicates whether Hellos are being suppressed to the neighbor |
| NUM jnxOspfv3NbrIfId | 1.3.6.1.4.1.2636.5.4.1.1.9.1.12 | InterfaceIndex | read-only | The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index. |
| INT jnxOspfv3NbrRestartHelperStatus | 1.3.6.1.4.1.2636.5.4.1.1.9.1.13 | INTEGER | read-only | Indicates whether the router is acting as a Graceful restart helper for the neighbor. |
| NUM jnxOspfv3NbrRestartHelperAge | 1.3.6.1.4.1.2636.5.4.1.1.9.1.14 | JnxOspfv3UpToRefreshIntervalTc | read-only | Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor. |
| INT jnxOspfv3NbrRestartHelperExitRc | 1.3.6.1.4.1.2636.5.4.1.1.9.1.15 | INTEGER | read-only | Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currentlyly underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change. |
| jnxOspfv3CfgNbrTable | 1.3.6.1.4.1.2636.5.4.1.1.10 | not-accessible | A table of configured, non-virtual neighbor information. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3CfgNbrEntry | 1.3.6.1.4.1.2636.5.4.1.1.10.1 | not-accessible | The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery. | |
| NUM jnxOspfv3CfgNbrIfIndex | 1.3.6.1.4.1.2636.5.4.1.1.10.1.1 | InterfaceIndex | not-accessible | The local link ID of the link over which the neighbor can be reached. |
| JNX jnxOspfv3CfgNbrIfInstId | 1.3.6.1.4.1.2636.5.4.1.1.10.1.2 | JnxOspfv3IfInstIdTc | not-accessible | Interface instance over which the neighbor can be reached. This ID has local link significance only. |
| IPt jnxOspfv3CfgNbrAddressType | 1.3.6.1.4.1.2636.5.4.1.1.10.1.3 | InetAddressType | not-accessible | The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected. |
| IP jnxOspfv3CfgNbrAddress | 1.3.6.1.4.1.2636.5.4.1.1.10.1.4 | InetAddress | not-accessible | The IPv6 address of the neighbor associated with the local link. |
| DES jnxOspfv3CfgNbrPriority | 1.3.6.1.4.1.2636.5.4.1.1.10.1.5 | DesignatedRouterPriority | read-create | The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network. |
| ROW jnxOspfv3CfgNbrStatus | 1.3.6.1.4.1.2636.5.4.1.1.10.1.6 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| jnxOspfv3VirtNbrTable | 1.3.6.1.4.1.2636.5.4.1.1.11 | not-accessible | A table of virtual neighbor information. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643. | |
| jnxOspfv3VirtNbrEntry | 1.3.6.1.4.1.2636.5.4.1.1.11.1 | not-accessible | Virtual neighbor information. | |
| JNX jnxOspfv3VirtNbrArea | 1.3.6.1.4.1.2636.5.4.1.1.11.1.1 | JnxOspfv3AreaIdTc | not-accessible | The Transit Area Identifier. |
| JNX jnxOspfv3VirtNbrRtrId | 1.3.6.1.4.1.2636.5.4.1.1.11.1.2 | JnxOspfv3RouterIdTc | not-accessible | A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. |
| NUM jnxOspfv3VirtNbrIfIndex | 1.3.6.1.4.1.2636.5.4.1.1.11.1.3 | InterfaceIndex | read-only | The local interface ID for the virtual link over which the neighbor can be reached. |
| JNX jnxOspfv3VirtNbrIfInstId | 1.3.6.1.4.1.2636.5.4.1.1.11.1.4 | JnxOspfv3IfInstIdTc | read-only | The interface instance for the virtual link over which the neighbor can be reached. |
| IPt jnxOspfv3VirtNbrAddressType | 1.3.6.1.4.1.2636.5.4.1.1.11.1.5 | InetAddressType | read-only | The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected. |
| IP jnxOspfv3VirtNbrAddress | 1.3.6.1.4.1.2636.5.4.1.1.11.1.6 | InetAddress | read-only | The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address. |
| I32 jnxOspfv3VirtNbrOptions | 1.3.6.1.4.1.2636.5.4.1.1.11.1.7 | Integer32 | read-only | A Bit Mask corresponding to the neighbor's options field. |
| INT jnxOspfv3VirtNbrState | 1.3.6.1.4.1.2636.5.4.1.1.11.1.8 | INTEGER | read-only | The state of the Virtual Neighbor Relationship. |
| C32 jnxOspfv3VirtNbrEvents | 1.3.6.1.4.1.2636.5.4.1.1.11.1.9 | Counter32 | read-only | The number of times this virtual link has changed its state, or an error has occurred. |
| G32 jnxOspfv3VirtNbrLsRetransQLen | 1.3.6.1.4.1.2636.5.4.1.1.11.1.10 | Gauge32 | read-only | The current length of the retransmission queue. |
| T/F jnxOspfv3VirtNbrHelloSuppressed | 1.3.6.1.4.1.2636.5.4.1.1.11.1.11 | TruthValue | read-only | Indicates whether Hellos are being suppressed to the neighbor |
| NUM jnxOspfv3VirtNbrIfId | 1.3.6.1.4.1.2636.5.4.1.1.11.1.12 | InterfaceIndex | read-only | The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID. |
| INT jnxOspfv3VirtNbrRestartHelperStatus | 1.3.6.1.4.1.2636.5.4.1.1.11.1.13 | INTEGER | read-only | Indicates whether the router is acting as a Graceful restart helper for the neighbor. |
| NUM jnxOspfv3VirtNbrRestartHelperAge | 1.3.6.1.4.1.2636.5.4.1.1.11.1.14 | JnxOspfv3UpToRefreshIntervalTc | read-only | Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor. |
| INT jnxOspfv3VirtNbrRestartHelperExitRc | 1.3.6.1.4.1.2636.5.4.1.1.11.1.15 | INTEGER | read-only | Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change. |
| jnxOspfv3AreaAggregateTable | 1.3.6.1.4.1.2636.5.4.1.1.12 | not-accessible | A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one. Marking this table and its objects deprecated as it is now implemented as part of RFC 5643. | |
| jnxOspfv3AreaAggregateEntry | 1.3.6.1.4.1.2636.5.4.1.1.12.1 | not-accessible | A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one. | |
| JNX jnxOspfv3AreaAggregateAreaID | 1.3.6.1.4.1.2636.5.4.1.1.12.1.1 | JnxOspfv3AreaIdTc | not-accessible | The Area the Address Aggregate is to be found within. |
| INT jnxOspfv3AreaAggregateAreaLsdbType | 1.3.6.1.4.1.2636.5.4.1.1.12.1.2 | INTEGER | not-accessible | The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to. |
| IPt jnxOspfv3AreaAggregatePrefixType | 1.3.6.1.4.1.2636.5.4.1.1.12.1.4 | InetAddressType | not-accessible | The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected. |
| IP jnxOspfv3AreaAggregatePrefix | 1.3.6.1.4.1.2636.5.4.1.1.12.1.5 | InetAddress | not-accessible | The IPv6 Prefix. |
| ADR jnxOspfv3AreaAggregatePrefixLength | 1.3.6.1.4.1.2636.5.4.1.1.12.1.6 | InetAddressPrefixLength | not-accessible | The length of the prefix (in bits). A prefix can not be shorter than 3 bits. |
| ROW jnxOspfv3AreaAggregateStatus | 1.3.6.1.4.1.2636.5.4.1.1.12.1.7 | RowStatus | read-create | This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| INT jnxOspfv3AreaAggregateEffect | 1.3.6.1.4.1.2636.5.4.1.1.12.1.8 | INTEGER | read-create | Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area. |
| INT jnxOspfv3AreaAggregateRouteTag | 1.3.6.1.4.1.2636.5.4.1.1.12.1.9 | INTEGER | read-create | This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSA's to AS-External-LSA's. |
| jnxOspfv3NotificationEntry | 1.3.6.1.4.1.2636.5.4.1.1.13 | |||
| INT jnxOspfv3ConfigErrorType | 1.3.6.1.4.1.2636.5.4.1.1.13.1 | INTEGER | accessible-for-notify | Potential types of configuration conflicts. Used by the ospfv3ConfigError and ospfv3ConfigVirtError notifications. When the last value of a notification using this object is needed, but no notifications of that type have been sent, this value pertaining to this object should be returned as noError |
| INT jnxOspfv3PacketType | 1.3.6.1.4.1.2636.5.4.1.1.13.2 | INTEGER | accessible-for-notify | OSPFv3 packet types. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as nullPacket |
| IP jnxOspfv3PacketSrc | 1.3.6.1.4.1.2636.5.4.1.1.13.3 | InetAddress | accessible-for-notify | The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as 0 Only IPv6 addresses without zone index are expected. |
| jnxOspfv3Conformance | 1.3.6.1.4.1.2636.5.4.1.2 | |||
| jnxOspfv3Groups | 1.3.6.1.4.1.2636.5.4.1.2.1 | |||
| jnxOspfv3BasicGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.1 | These objects are used for managing/monitoring OSPFv3 global parameters. | ||
| jnxOspfv3AreaGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.2 | These objects are used for ospfv3 systems supporting areas. | ||
| jnxOspfv3AsLsdbGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.3 | These objects are used for ospfv3 systems that display their AS-scope link state database. | ||
| jnxOspfv3AreaLsdbGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.4 | These objects are used for OSPFv3 systems that display their Area-scope link state database. | ||
| jnxOspfv3LinkLsdbGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.5 | These objects are used for OSPFv3 systems that display their Link-scope link state database. | ||
| jnxOspfv3HostGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.6 | These objects are used for OSPFv3 systems that support attached hosts. | ||
| jnxOspfv3IfGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.7 | These interface objects used for managing/monitoring OSPFv3 interfaces. | ||
| jnxOspfv3VirtIfGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.8 | These virtual interface objects are used for managing/monitoring OSPFv3 virtual interfaces. | ||
| jnxOspfv3NbrGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.9 | These neighbor objects are used for managing/monitoring OSPFv3 neighbors. | ||
| jnxOspfv3CfgNbrGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.10 | These configured neighbor objects are used for managing/monitoring ospfv3 configured neighbors. | ||
| jnxOspfv3VirtNbrGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.11 | These virtual neighbor objects are used for managing/monitoring OSPFv3 virtual neighbors. | ||
| jnxOspfv3AreaAggregateGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.12 | These area aggregate objects used required for aggregating OSPFv3 prefixes for summarization across areas. | ||
| jnxOspfv3NotificationObjectGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.13 | These objects are used to record notification parameters | ||
| jnxOspfv3NotificationGroup | 1.3.6.1.4.1.2636.5.4.1.2.1.14 | This group is used for OSPFv3 notifications | ||
| jnxOspfv3Compliances | 1.3.6.1.4.1.2636.5.4.1.2.2 | |||
| jnxOspfv3Compliance | 1.3.6.1.4.1.2636.5.4.1.2.2.1 | The compliance statement |
RFC description
Manages OSPFv3 routing protocol for IPv6 networks on Juniper devices. Provides interface, neighbor, and route tracking (deprecated in favor of RFC 5643).
Start monitoring Juniper Networks router/switch running OSPFv3 with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.